If the PWM was not enabled at U-Boot loader, PWM could not work for
clock always disabled at PWM driver. The PWM clock is enabled at
beginning of pwm_apply(), but disabled at end of pwm_apply().
If the PWM was enabled at U-Boot loader, PWM clock is always enabled
unless closed by ATF. The pwm-backlight might turn off the power at
early suspend, should disable PWM clock for saving power consume.
It is important to provide opportunity to enable/disable clock at PWM
driver, the PWM consumer should ensure correct order to call PWM enable
and disable, and PWM driver ensure state of PWM clock synchronized with
PWM enabled state.
Fixes: 2bf1c98aa5 ("pwm: rockchip: Add support for atomic update")
Cc: stable@vger.kernel.org
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
At least on cherrytrail, the update bit will never go low when the
enabled bit is not set.
This causes the backlight on my cube iwork8 air tablet to never turn on
again after being turned off because in the pwm_lpss_apply enable path
pwm_lpss_update will fail causing an error exit and the enable-bit to
never get set. Any following pwm_lpss_apply calls will fail the
pwm_lpss_is_updating check.
Since the docs say that the update bit should be set before the
enable-bit, split pwm_lpss_update into setting the update-bit and
pwm_lpss_wait_for_update, and move the pwm_lpss_wait_for_update call
in the enable path to after setting the enable-bit.
Fixes: 10d56a4 ("pwm: lpss: Avoid reconfiguring while UPDATE bit...")
Cc: Ilkka Koskinen <ilkka.koskinen@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As a preparation for special treatment for Broxton we split Tangier
configuration.
Fixes: b89b4b7a3d ("pwm: lpss: pci: Enable PWM module on Intel Edison")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This set contains mostly fixes to existing drivers as well as cleanup of
code that's not been in active use for a while.
-----BEGIN PGP SIGNATURE-----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=J9q4
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set contains mostly fixes to existing drivers as well as cleanup
of code that's not been in active use for a while"
* tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (27 commits)
acpi: lpss: call pwm_add_table() for BSW PWM device
pwm: Try to load modules during pwm_get()
pwm: Don't hold pwm_lookup_lock longer than necessary
pwm: Make the PWM_POLARITY flag in DTB optional
pwm: Print error messages with pr_err() instead of pr_debug()
pwm: imx: Add polarity inversion support to i.MX's PWMv2
pwm: imx: doc: Update imx-pwm.txt documentation entry
pwm: imx: Remove redundant i.MX PWMv2 code
pwm: imx: Provide atomic PWM support for i.MX PWMv2
pwm: imx: Move PWMv2 wait for fifo slot code to a separate function
pwm: imx: Move PWMv2 software reset code to a separate function
pwm: imx: Rewrite v1 code to facilitate switch to atomic PWM
pwm: imx: Add separate set of PWM ops for v1 and v2
pwm: imx: Remove ipg clock and enable per clock when required
pwm: lpss: Add Intel Gemini Lake PCI ID
pwm: lpss: Do not export board infos for different PWM types
pwm: lpss: Avoid reconfiguring while UPDATE bit is still enabled
pwm: lpss: Switch to new atomic API
pwm: lpss: Allow duty cycle to be 0
pwm: lpss: Avoid potential overflow of base_unit
...
Add a module name string to the pwm_lookup struct and if specified try
to load the module using request_module() if pwmchip_find_by_name() is
unable to find the PWM chip.
This is a last resort to work around drivers that can't - and can't be
made to - deal with deferred probe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[thierry.reding@gmail.com: rename new macro, reword commit message]
[thierry.reding@gmail.com: add comment explaining use-case]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is no need to hold pwm_lookup_lock after we're done with looping
over pwm_lookup_list, so release it earlier.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Change the PWM chip driver registration so that a chip driver that
supports polarity inversion can still be used with DTBs that don't
provide the polarity flag as part of the specifier.
This is done to provide polarity inversion support for the pwm-imx
driver without having to modify all existing DTS files.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Make the messages that are printed in case of fatal errors actually
visible to the user without having to recompile the driver with
debugging enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With this patch the polarity settings for i.MX's PWMv2 is now supported
on top of atomic PWM setting
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The code providing functionality surpassed by the atomic PWM is not
needed anymore and hence can be removed.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The code, which waits for fifo slot, has been extracted from
imx_pwm_config_v2 function and moved to new one - imx_pwm_wait_fifo_slot().
This change reduces the overall size of imx_pwm_config_v2() and prepares
it for atomic PWM operation.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The software reset code has been extracted from imx_pwm_config_v2 function
and moved to new one - imx_pwm_sw_reset().
This change reduces the overall size of imx_pwm_config_v2() and prepares
it for atomic PWM operation.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The code has been rewritten to remove "generic" calls to
imx_pwm_{enable|disable|config}.
Such approach would facilitate switch to atomic PWM (a.k.a ->apply())
implementation.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch provides separate set of PWM operations utilized by i.MX's
v1 and v2 of the PWM hardware.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The use of the ipg clock was introduced with commit 7b27c160c6 ("pwm:
i.MX: fix clock lookup"). In the commit message it was claimed that the
ipg clock is enabled for register accesses. This is true for the
->config() callback, but not for the ->set_enable() callback. Given that
the ipg clock is not consistently enabled for all register accesses we
can assume that either it is not required at all or that the current
code does not work. Remove the ipg clock code for now so that it's no
longer in the way of refactoring the driver.
On the other hand, the i.MX 7 IP requires the peripheral clock to be
enabled before accessing its registers. Since ->config() can be called
when the PWM is disabled (in which case, the peripheral clock is also
disabled), we need to surround the imx->config() with
clk_prepare_enable(per_clk)/clk_disable_unprepare(per_clk) calls.
Note that the driver was working fine for the i.MX 7 IP so far because
the ipg and peripheral clock use the same hardware clock gate, which
guaranteed peripheral clock activation even when ->config() was called
when the PWM was disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Intel Gemini Lake PWM is pretty much same as used in Intel Broxton. Add
this new PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM LPSS probe drivers just pass a pointer to the exported board
info structures to pwm_lpss_probe() based on device PCI or ACPI ID.
In order to remove the knowledge of specific devices from library part of
the driver and reduce noise in exported namespace just duplicate the
board info structures and stop exporting them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
PWM Configuration register has SW_UPDATE bit that is set when a new
configuration is written to the register. The bit is automatically
cleared at the start of the next output cycle by the IP block.
If one writes a new configuration to the register while it still has
the bit enabled, PWM may freeze. That is, while one can still write
to the register, it won't have an effect. Thus, we try to sleep long
enough that the bit gets cleared and make sure the bit is not
enabled while we update the configuration.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Richard Griffiths <richard.a.griffiths@intel.com>
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of doing things separately, which is not so reliable on some platforms,
switch the driver to use new atomic API, i.e. ->apply() callback.
The change has been tested on Intel platforms such as Broxton, BayTrail, and
Merrifield.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A duty cycle is represented by values [0..<period>] which reflects [0%..100%].
0% of the duty cycle means always off (logical "0") on output. Allow this in
the driver.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The resolution of base_unit is derived from base_unit_bits and thus must be
equal to (2^base_unit_bits - 1). Otherwise frequency and therefore base_unit
might potentially overflow.
Prevent the above by substracting 1 in all cases where base_unit_bits or
derivative is used.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This driver adds support for PWM driver on STM32 platform.
The SoC have multiple instances of the hardware IP and each
of them could have small differences: number of channels,
complementary output, auto reload register size...
version 9:
- fix commit message header
- remove one space MODULE_ALIAS
version 8:
- fix comments done by Thierry on version 7
version 6:
- change st,breakinput parameter to make it usuable for stm32f7 too.
version 4:
- detect at probe time hardware capabilities
- fix comments done on v2 and v3
- use PWM atomic ops
version 2:
- only keep one comptatible
- use DT parameters to discover hardware block configuration
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When first implementing support for changing the output frequency, an
optimization was added to continue the PWM after changing the prescaler
without having to reprogram the ON and OFF registers for the duty cycle,
in case the duty cycle stayed the same. This was flawed, because we
compared the absolute value of the duty cycle in nanoseconds instead of
the ratio to the period.
Fix the problem by removing the shortcut.
Fixes: 01ec847200 ("pwm-pca9685: Support changing the output frequency")
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Declare pwm_ops structures as const as they are only stored in the ops
field of a pwm_chip structure. This field is of type const struct pwm_ops
*, so pwm_ops structures having this property can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct pwm_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct pxa_pwm_chip pwm;
struct bfin_pwm_chip bwm;
struct vt8500_chip vp;
struct imx_chip icp;
@@
(
pwm.chip.ops=&i@p
|
bwm.chip.ops=&i@p
|
vp.chip.ops=&i@p
|
icp.chip.ops=&i@p
)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct pwm_ops i;
File size details:
text data bss dec hex filename
1646 328 0 1974 7b6 drivers/pwm/pwm-imx.o
1742 224 0 1966 7ae drivers/pwm/pwm-imx.o
1941 296 0 2237 8bd drivers/pwm/pwm-pxa.o
2037 192 0 2229 8b5 drivers/pwm/pwm-pxa.o
1946 296 0 2242 8c2 drivers/pwm/pwm-vt8500.o
2050 192 0 2242 8c2 drivers/pwm/pwm-vt8500.o
The drivers/pwm/pwm-bfin.o file did not compile.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add dependency on COMMON_CLK and allow COMPILE_TEST for broader compile
coverage. Default to Y for IPROC SoCs. This allows the driver to simply
be enabled by selecting PWM.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
[thierry.reding@gmail.com: reword commit message]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PCA9685 controller has full on/off bit for each PWM channel. Setting
this bit bypasses the PWM control and the line works just as it would be a
GPIO. Furthermore in Intel Galileo it is actually used as GPIO output for
discreet muxes on the board.
This patch adds GPIO output only support for the driver so that we can
control the muxes on Galileo using standard GPIO interfaces available in
the kernel. GPIO and PWM functionality is exclusive so only one can be
active at a time on a single PWM channel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
All PWM devices have been marked as "might sleep" since v4.5, there is
no longer a need to differentiate on a per-chip basis.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This is a very tiny pull request, with just a new driver for HiSilicon
BVT SoCs and a cleanup for the Amlogic Meson driver.
There are other patches on the list, but my timing was really bad this
time and I ended up not having the time to look at them in enough detail
to be comfortable merging them.
-----BEGIN PGP SIGNATURE-----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=WHNA
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This is a very tiny pull request, with just a new driver for HiSilicon
BVT SoCs and a cleanup for the Amlogic Meson driver.
There are other patches on the list, but my timing was really bad this
time and I ended up not having the time to look at them in enough
detail to be comfortable merging them"
* tag 'pwm/for-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Add PWM driver for HiSilicon BVT SOCs
pwm: meson: Remove unneeded platform MODULE_ALIAS
Add PWM driver for the PWM controller found on HiSilicon BVT SoCs such
as Hi3519V100, Hi3516CV300, etc. The PWM controller is primarily in
charge of controlling the P-Iris lens.
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Jian Yuan <yuanjian12@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Make sure to drop the reference to the parent device taken by
class_find_device() after "unexporting" any children when deregistering
a PWM chip.
Fixes: 0733424c9b ("pwm: Unexport children before chip removal")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The Amlogic Meson is a DT-only platform, which means the devices are
registered via OF and not using the legacy platform devices support.
So there's no need to have a MODULE_ALIAS("platform:meson-pwm") since
the reported uevent MODALIAS to user-space will always be the OF one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The driver uses the spin_lock but does not initialize it. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When building with -Wmaybe-uninitialized, we get a couple of harmless
warnings about three functions in this new driver that don't look
safe to the compiler:
drivers/pwm/pwm-meson.c: In function 'meson_pwm_get_state':
drivers/pwm/pwm-meson.c:355:26: error: 'mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c: In function 'meson_pwm_disable':
drivers/pwm/pwm-meson.c:263:13: error: 'enable' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c: In function 'meson_pwm_apply':
drivers/pwm/pwm-meson.c:231:13: error: 'clk_shift' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c:231:36: error: 'enable' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c:231:24: error: 'clk_enable' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Specifically, if we have a device with an ID other than 0 or 1,
this would result in undefined behavior. This is currently not
possible, but the compiler cannot be expected to know this.
This patch adds a 'default' clause to let the compiler know
what to do instead, which shuts up the warning and makes the
code slightly more resiliant in case it gets extended to other
identifiers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This includes fixing some Coding Style issues and re-ordering and/or
simplifying a little code.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[thierry.reding@gmail.com: applied some bikeshedding>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Setting up the STI PWM IP as capture only, with zero PWM output devices
is a perfectly valid configuration. It is no longer okay to assume that
there must be at least 1 PWM output device. In this patch we make the
default number of PWM output devices zero and only configure channels
explicitly requested.
Reported-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Once a PWM capture has been initiated, the capture call enables a rising
edge detection interrupt, then waits. Once each of the 3 phase changes
have been recorded the thread then wakes. The remaining part of the call
carries out the relevant calculations and returns a structure filled out
with the capture data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Here we're requesting the PWM capture IRQ and supplying the handler that
will be called in the event of an interrupt to handle it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Each PWM capture device is allocated a structure to hold its own state.
During a capture the device may be partaking in one of 3 phases. Initial
(rising) phase change, a subsequent (falling) phase change indicating
end of the duty-cycle phase and finally a final (rising) phase change
indicating the end of the period. The timer value snapshot each event is
held in a variable of the same name, and the phase number (0, 1, 2) is
contained in the index variable. Other device specific information, such
as GPIO pin, the IRQ wait queue and locking is also contained in the
structure. This patch initialises this structure for each of the
available devices.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
ST's PWM IP is supplied by 2 different clocks. One for PWM output and
the other for capture. This patch provides clock handling for the
latter.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This is in preparation for subsequent patches that add support for PWM
capture to this driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In the original code the clock rate was only obtained during
initialisation; however, the rate may change between then and
its use. This patch ensures the correct rate is acquired just
before use.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Exciting functionality is on the way to this device. But
before we can add it, we need to do some basic housekeeping
so the additions can be added cleanly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This is to bring the terminology used in the STi PWM driver more
into line with the PWM subsystem.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The lpc-18xx driver currently manipulates the pwm_device struct directly
rather than using the pwm_set_chip_data() function. While the current
method may save a clock cycle or two, using the explicit function call
makes it more obvious that data is set to the local chip data pointer.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for the PWM controller found in the Amlogic SoCs. This
driver supports the Meson8b and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
