The function really shouldn't be called prepare_for_handlers(),
all it does is check if the frame should be dropped. Rename it
to ieee80211_accept_frame() and clean it up a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With promisc support gone, only AP and P2P-Device type interfaces
still clear IEEE80211_RX_RA_MATCH. In both cases this isn't really
necessary though, so we can remove that flag and the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow debug builds to configure the station hash table maximum
size in order to run with hash collisions in limited scenarios
such as hwsim testing. The default remains 0 which effectively
means no limit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the necessary software segmentation on the normal
TX path so that fast-xmit can use segmentation offload if
the hardware (or driver) supports it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drivers want to support S/G (really just gather DMA on TX) then
we can now easily support this on the fast-xmit path since it just
needs to write to the ethernet header (and already has a check for
that being possible.)
However, disallow this on the regular TX path (which has to handle
fragmentation, software crypto, etc.) by calling skb_linearize().
Also allow the related HIGHDMA since that's not interesting to the
code in mac80211 at all anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we go through the complete TX processing, there are a number
of things like fragmentation and software crypto that require the
checksum to be calculated already.
In favour of maintainability, instead of adding the necessary call
to skb_checksum_help() in all the places that need it, just do it
once before the regular TX processing.
Right now this only affects the TI wlcore and QCA ath10k drivers
since they're the only ones using checksum offload. The previous
commits enabled fast-xmit for them in almost all cases.
For wlcore this even fixes a corner case: when a key fails to be
programmed to hardware software encryption gets used, encrypting
frames with a bad checksum.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IBSS can be supported very easily since it uses the standard station
authorization state etc. so it just needs to be covered by the header
building switch statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When crypto is offloaded then in some cases it's all handled
by the device, and in others only some space for the IV must
be reserved in the frame. Handle both of these cases in the
fast-xmit path, up to a limit of 18 bytes of space for IVs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver handles fragmentation then it wouldn't
be done in software so we can still use the fast-xmit
path in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to speed up mac80211's TX path, add the "fast-xmit" cache
that will cache the data frame 802.11 header and other data to be
able to build the frame more quickly. This cache is rebuilt when
external triggers imply changes, but a lot of the checks done per
packet today are simplified away to the check for the cache.
There's also a more detailed description in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both minstrel (reported by Sven Eckelmann) and the iwlwifi rate
control aren't properly taking concurrency into account. It's
likely that the same is true for other rate control algorithms.
In the case of minstrel this manifests itself in crashes when an
update and other data access are run concurrently, for example
when the stations change bandwidth or similar. In iwlwifi, this
can cause firmware crashes.
Since fixing all rate control algorithms will be very difficult,
just provide locking for invocations. This protects the internal
data structures the algorithms maintain.
I've manipulated hostapd to test this, by having it change its
advertised bandwidth roughly ever 150ms. At the same time, I'm
running a flood ping between the client and the AP, which causes
this race of update vs. get_rate/status to easily happen on the
client. With this change, the system survives this test.
Reported-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh plink code uses sta->lock to serialize access to the
plink state fields between the peer link state machine and the
peer link timer. Some paths (e.g. those involving
mps_qos_null_tx()) unfortunately hold this spinlock across
frame tx, which is soon to be disallowed. Add a new spinlock
just for plink access.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that
user space tools like perf and trace-cmd can parse the binary data
and express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values
by the C pre-processor. Thus, the enum string is exported to the
format file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings
in the TP_printk() format into their number, and that is what is
shown to user space. For example, the tracepoint tlb_flush currently
has this in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVLBTuAAoJEEjnJuOKh9ldjHMIALdRS755TXCZGOf0r7O2akOR
wMPeum7C+ae1mH+jCsJKUC0/jUfQKaMt/UxoHlipDgcGg8kD2jtGnGCw4Xlwvdsr
y4rFmcTRSl1mo0zDSsg6ujoupHlVYN0+JPjrd7S3cv/llJoY49zcanNLF7S2XLeM
dZCtWRLWYpBiWO68ai6AqJTnE/eGFIqBI048qb5Eg8dbK243SSeSIf9Ywhb+VsA+
aq6F7cWI/H6j4tbeza8tAN19dcwenDro5EfCDY8ARQHJu1f6Y3+DLf2imjkd6Aiu
JVAoGIjHIpI+djwCZC1u4gi4urjfOqYartrM3Q54tb3YWYqHeNqP2ASI2a4EpYk=
=Ixwt
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Some clean ups and small fixes, but the biggest change is the addition
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that user
space tools like perf and trace-cmd can parse the binary data and
express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values by
the C pre-processor. Thus, the enum string is exported to the format
file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings in
the TP_printk() format into their number, and that is what is shown to
user space. For example, the tracepoint tlb_flush currently has this
in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })"
* tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (27 commits)
tracing: Add enum_map file to show enums that have been mapped
writeback: Export enums used by tracepoint to user space
v4l: Export enums used by tracepoints to user space
SUNRPC: Export enums in tracepoints to user space
mm: tracing: Export enums in tracepoints to user space
irq/tracing: Export enums in tracepoints to user space
f2fs: Export the enums in the tracepoints to userspace
net/9p/tracing: Export enums in tracepoints to userspace
x86/tlb/trace: Export enums in used by tlb_flush tracepoint
tracing/samples: Update the trace-event-sample.h with TRACE_DEFINE_ENUM()
tracing: Allow for modules to convert their enums to values
tracing: Add TRACE_DEFINE_ENUM() macro to map enums to their values
tracing: Update trace-event-sample with TRACE_SYSTEM_VAR documentation
tracing: Give system name a pointer
brcmsmac: Move each system tracepoints to their own header
iwlwifi: Move each system tracepoints to their own header
mac80211: Move message tracepoints to their own header
tracing: Add TRACE_SYSTEM_VAR to xhci-hcd
tracing: Add TRACE_SYSTEM_VAR to kvm-s390
tracing: Add TRACE_SYSTEM_VAR to intel-sst
...
* new mac80211 internal software queue to allow drivers to have
shorter hardware queues and pull on-demand
* use rhashtable for mac80211 station table
* minstrel rate control debug improvements and some refactoring
* fix noisy message about TX power reduction
* fix continuous message printing and activity if CRDA doesn't respond
* fix VHT-related capabilities with "iw connect" or "iwconfig ..."
* fix Kconfig for cfg80211 wireless extensions compatibility
-----BEGIN PGP SIGNATURE-----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=mtuo
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
There isn't much left, but we have
* new mac80211 internal software queue to allow drivers to have
shorter hardware queues and pull on-demand
* use rhashtable for mac80211 station table
* minstrel rate control debug improvements and some refactoring
* fix noisy message about TX power reduction
* fix continuous message printing and activity if CRDA doesn't respond
* fix VHT-related capabilities with "iw connect" or "iwconfig ..."
* fix Kconfig for cfg80211 wireless extensions compatibility
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Every tracing file must have its own TRACE_SYSTEM defined.
The mac80211 tracepoint header broke this and add in the middle
of the file had:
#undef TRACE_SYSTEM
#define TRACE_SYSTEM mac80211_msg
Unfortunately, this broke new code in the ftrace infrastructure.
Moving the mac80211_msg into its own trace file with its own
TRACE_SYSTEM defined fixes the issue.
Link: http://lkml.kernel.org/r/1428389938.1841.1.camel@sipsolutions.net
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This changes a couple of messages from sdata_info to sdata_dbg.
This should reduce some log spam, as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=1206468
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the statistical descriptor "standard deviation"
to better describe the current properties of Minstrel and
Minstrel-HTs success probability distribution. The standard
deviation (SD) is calculated as exponential weighted moving
standard deviation (EWMSD) and its current value is added as
new column in all rc_stats (in debugfs).
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch reduces the calculation costs of the EWMA macro from
"2x multiplication and 1 addition" down to "1x multiplication and
2x additions". This slightly improves performance depending on the
CPU architecture.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the new statistic "maximum possible lossless
throughput" to Minstrels and Minstrel-HTs rc_stats (in debugfs). This
enables comprehensive comparison between current per-rate throughput
and max. achievable per-rate throughput.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch moves Minstrels and Minstrel-HTs per-rate throughput
calculation (EWMA(thr)) into a dedicated function to be called.
Therefore the variable "unsigned int cur_tp" within struct
"minstrel_rate_stats" becomes obsolete. and is removed to free
up its space.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch ensures a consistent usage of variable names for type
"minstrel_rate_stats" to be used as "mrs" and from type minstrel_rate
as "mr" across both Minstrel & Minstrel-HT. In addition some
variable and function names got changed to more meaningful ones.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch unifies the calculation of Minstrels and Minstrel-HTs
per-rate statistic. The new common function minstrel_calc_rate_stats()
is called when a statistic update is performed.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a new debugfs file "rc_stats_csv" to output
Minstrel-HTs statistics in a common csv format that is easy
to parse.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
[remove printing current time of day]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a new debugfs file "rc_stats_csv" to output Minstrels
statistics in a common csv format that is easy to parse.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
[remove printing current time of day]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch restructures the rc_stats debugfs table of Minstrel-HT in
order to achieve better human readability. A new layout of the
statistics and a new header is added. In addition to the old layout
there are two new columns of information added:
idx - representing the rate index of each rate in mac80211 which
can be used to set specific rates as fixed rate via debugfs
airtime - the tx-time in micro seconds that a 1200 Byte packet
takes to be transmitted over the air at the given rate
The old layout of rc_stats:
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
HT20/LGI MCS0 5.6 100.0 100.0 1 0( 0) 1( 1)
HT20/LGI B MCS1 10.5 100.0 100.0 0 0( 0) 1( 1)
HT20/LGI A MCS2 14.8 100.0 100.0 0 0( 0) 1( 1)
...
is changed into this new layout:
best ________rate______ __statistics__ ________last_______ ______sum-of________
mode guard # rate [name idx airtime] [ ø(tp) ø(prob)] [prob.|retry|suc|att] [#success | #attempts]
HT20 LGI 1 MCS0 0 1480 0.0 0.0 0.0 1 0 0 0 0
HT20 LGI 1 B MCS1 1 740 10.5 100.0 100.0 0 0 0 1 1
HT20 LGI 1 A MCS2 2 496 14.8 100.0 100.0 0 0 0 1 1
...
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch restructures the rc_stats debugfs table of Minstrel in
order to achieve better human readability. A new layout of the
statistics and a new header is added. In addition to the old layout
there are two new columns of information added:
idx - representing the rate index of each rate in mac80211 which
can be used to set specific rates as fixed rate via debugfs
airtime - the tx-time in micro seconds that a 1200 Byte packet
takes to be transmitted over the air at the given rate
The old layout of rc_stats:
rate tpt eprob *prob ret *ok(*cum) ok( cum)
DP 1 0.9 93.5 100.0 1 0( 0) 2( 2)
2 0.4 40.0 100.0 0 0( 0) 4( 10)
5.5 0.0 0.0 0.0 0 0( 0) 0( 0)
...
is changed into this new layout:
best _______rate_____ __statistics__ ________last_______ ______sum-of________
rate [name idx tx-time] [ ø(tp) ø(prob)] [prob.|retry|suc|att] [#success | #attempts]
DP 1 0 9738 0.9 93.5 100.0 1 1 1 2 2
2 1 4922 0.4 40.0 100.0 1 0 0 4 10
5.5 2 1858 0.0 0.0 0.0 2 0 0 0 0
...
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently have a hand-rolled table with 256 entries and are
using the last byte of the MAC address as the hash. This hash
is obviously very fast, but collisions are easily created and
we waste a lot of space in the common case of just connecting
as a client to an AP where we just have a single station. The
other common case of an AP is also suboptimal due to the size
of the hash table and the ease of causing collisions.
Convert all of this to use rhashtable with jhash, which gives
us the advantage of a far better hash function (with random
perturbation to avoid hash collision attacks) and of course
that the hash table grows and shrinks dynamically with chain
length, improving both cases above.
Use a specialised hash function (using jhash, but with fixed
length) to achieve better compiler optimisation as suggested
by Sergey Ryazanov.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the upcoming fast-xmit patch, changing station state will
build a header cache based on the station's capabilities, and
as the QoS capability (sta.wme) impacts the header, it needs
to be set before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These are mandated by IEEE802.11-2012 section 8.5.8.6 and IEEE802.11ac-2013
section 8.5.8.16.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT support for IBSS. Drivers could activate
this feature by setting NL80211_EXT_FEATURE_VHT_IBSS
flag.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of wide bandwidth (wider than 20MHz) used by IBSS,
scan all channels in chandef to be able to find neighboring
IBSS netwqworks that use the same overall channels but a different
control channel.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to look up the RA station earlier to implement a TX
fastpath, factor out the lookup from ieee80211_build_hdr().
To always have a valid station pointer, also move some of the
checks into the new function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Indicating just the peer's capability is fairly pointless
if the local device doesn't support it. Make the variable
track both combined, and remove the 'local support' check
in the TX path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Louis reported that a static checker was complaining that
the 'dst' variable was set (multiple times) but not used.
This is due to a previous commit having removed the usage
(apparently erroneously), so add it back.
Fixes: a344d6778a ("mac80211: allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR")
Reported-by: Louis Langholtz <lou_langholtz@me.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is written using an anti-pattern called "success handling"
which makes it hard to read, especially if you are used to normal kernel
style. It should instead be written as a list of directives in a row
with branches for error handling.
(Basically copied from Dan's previous patch for CCM)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is written using an anti-pattern called "success handling"
which makes it hard to read, especially if you are used to normal kernel
style. It should instead be written as a list of directives in a row
with branches for error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 8ade538bf3 ("mac80111: Add BIP-GMAC-128 and BIP-GMAC-256
ciphers") had the success return in incorrect place before the
crypto_aead_setauthsize() call which practically ended up skipping that
call unconditionally.
The missing call did not actually change any functionality since
GMAC_MIC_LEN (16) is identical to the maxauthsize in gcm(aes) and as
such, the default value used for the authsize parameter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a peer or some local agent (rate control, ...) decides to start
an aggregation session but doesn't support HT (which also implies
QoS), reject it.
This is mostly a corner case as such peers normally won't try to
use block-ack sessions and rate control wouldn't start them, but
technically QoS stations could request it according to the spec.
However, since drivers don't really support such non-HT sessions
it's better to reject them.
Also, while at it, move the tracing for TX sessions earlier so it
captures the error cases as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Seems Broadcom TDLS peers (Nexus 5, Xperia Z3) refuse to allow TDLS
connection when channel-switching is supported but the regulatory
classes IE is missing from the setup request.
Add a chandef to reg-class translation function to cfg80211 and use it
to add the required IE during setup. For now add only the current
regulatory class as supported - it is enough to resolve the
compatibility issue.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop scan before authentication or association to make sure
that nothing interferes with connection flow.
Currently mac80211 defers RX auth and assoc packets (among other ones)
until after the scan is complete, so auth during scan is likely to fail
if scan took too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the reason
of the deauth.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
