Even if we send an IPv6 packet without options, MAX_HEADER might not be
enough to account for the additional headroom required by alignment of
hardware headers.
On a configuration without HYPERV_NET, WLAN, AX25, and with IPV6_TUNNEL,
sending short SCTP packets over IPv4 over L2TP over IPv6, we start with
100 bytes of allocated headroom in sctp_packet_transmit(), end up with 54
bytes after l2tp_xmit_skb(), and 14 bytes in ip6_finish_output2().
Those would be enough to append our 14 bytes header, but we're going to
align that to 16 bytes, and write 2 bytes out of the allocated slab in
neigh_hh_output().
KASan says:
[ 264.967848] ==================================================================
[ 264.967861] BUG: KASAN: slab-out-of-bounds in ip6_finish_output2+0x1aec/0x1c70
[ 264.967866] Write of size 16 at addr 000000006af1c7fe by task netperf/6201
[ 264.967870]
[ 264.967876] CPU: 0 PID: 6201 Comm: netperf Not tainted 4.20.0-rc4+ #1
[ 264.967881] Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
[ 264.967887] Call Trace:
[ 264.967896] ([<00000000001347d6>] show_stack+0x56/0xa0)
[ 264.967903] [<00000000017e379c>] dump_stack+0x23c/0x290
[ 264.967912] [<00000000007bc594>] print_address_description+0xf4/0x290
[ 264.967919] [<00000000007bc8fc>] kasan_report+0x13c/0x240
[ 264.967927] [<000000000162f5e4>] ip6_finish_output2+0x1aec/0x1c70
[ 264.967935] [<000000000163f890>] ip6_finish_output+0x430/0x7f0
[ 264.967943] [<000000000163fe44>] ip6_output+0x1f4/0x580
[ 264.967953] [<000000000163882a>] ip6_xmit+0xfea/0x1ce8
[ 264.967963] [<00000000017396e2>] inet6_csk_xmit+0x282/0x3f8
[ 264.968033] [<000003ff805fb0ba>] l2tp_xmit_skb+0xe02/0x13e0 [l2tp_core]
[ 264.968037] [<000003ff80631192>] l2tp_eth_dev_xmit+0xda/0x150 [l2tp_eth]
[ 264.968041] [<0000000001220020>] dev_hard_start_xmit+0x268/0x928
[ 264.968069] [<0000000001330e8e>] sch_direct_xmit+0x7ae/0x1350
[ 264.968071] [<000000000122359c>] __dev_queue_xmit+0x2b7c/0x3478
[ 264.968075] [<00000000013d2862>] ip_finish_output2+0xce2/0x11a0
[ 264.968078] [<00000000013d9b14>] ip_finish_output+0x56c/0x8c8
[ 264.968081] [<00000000013ddd1e>] ip_output+0x226/0x4c0
[ 264.968083] [<00000000013dbd6c>] __ip_queue_xmit+0x894/0x1938
[ 264.968100] [<000003ff80bc3a5c>] sctp_packet_transmit+0x29d4/0x3648 [sctp]
[ 264.968116] [<000003ff80b7bf68>] sctp_outq_flush_ctrl.constprop.5+0x8d0/0xe50 [sctp]
[ 264.968131] [<000003ff80b7c716>] sctp_outq_flush+0x22e/0x7d8 [sctp]
[ 264.968146] [<000003ff80b35c68>] sctp_cmd_interpreter.isra.16+0x530/0x6800 [sctp]
[ 264.968161] [<000003ff80b3410a>] sctp_do_sm+0x222/0x648 [sctp]
[ 264.968177] [<000003ff80bbddac>] sctp_primitive_ASSOCIATE+0xbc/0xf8 [sctp]
[ 264.968192] [<000003ff80b93328>] __sctp_connect+0x830/0xc20 [sctp]
[ 264.968208] [<000003ff80bb11ce>] sctp_inet_connect+0x2e6/0x378 [sctp]
[ 264.968212] [<0000000001197942>] __sys_connect+0x21a/0x450
[ 264.968215] [<000000000119aff8>] sys_socketcall+0x3d0/0xb08
[ 264.968218] [<000000000184ea7a>] system_call+0x2a2/0x2c0
[...]
Just like ip_finish_output2() does for IPv4, check that we have enough
headroom in ip6_xmit(), and reallocate it if we don't.
This issue is older than git history.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'seg6_output', stack variable 'struct flowi6 fl6' was missing
initialization.
Fixes: 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *_frag_reasm() functions are susceptible to miscalculating the byte
count of packet fragments in case the truesize of a head buffer changes.
The truesize member may be changed by the call to skb_unclone(), leaving
the fragment memory limit counter unbalanced even if all fragments are
processed. This miscalculation goes unnoticed as long as the network
namespace which holds the counter is not destroyed.
Should an attempt be made to destroy a network namespace that holds an
unbalanced fragment memory limit counter the cleanup of the namespace
never finishes. The thread handling the cleanup gets stuck in
inet_frags_exit_net() waiting for the percpu counter to reach zero. The
thread is usually in running state with a stacktrace similar to:
PID: 1073 TASK: ffff880626711440 CPU: 1 COMMAND: "kworker/u48:4"
#5 [ffff880621563d48] _raw_spin_lock at ffffffff815f5480
#6 [ffff880621563d48] inet_evict_bucket at ffffffff8158020b
#7 [ffff880621563d80] inet_frags_exit_net at ffffffff8158051c
#8 [ffff880621563db0] ops_exit_list at ffffffff814f5856
#9 [ffff880621563dd8] cleanup_net at ffffffff814f67c0
#10 [ffff880621563e38] process_one_work at ffffffff81096f14
It is not possible to create new network namespaces, and processes
that call unshare() end up being stuck in uninterruptible sleep state
waiting to acquire the net_mutex.
The bug was observed in the IPv6 netfilter code by Per Sundstrom.
I thank him for his analysis of the problem. The parts of this patch
that apply to IPv4 and IPv6 fragment reassembly are preemptive measures.
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Reported-by: Per Sundstrom <per.sundstrom@redqube.se>
Acked-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Disable BH while holding list spinlock in nf_conncount, from
Taehee Yoo.
2) List corruption in nf_conncount, also from Taehee.
3) Fix race that results in leaving around an empty list node in
nf_conncount, from Taehee Yoo.
4) Proper chain handling for inactive chains from the commit path,
from Florian Westphal. This includes a selftest for this.
5) Do duplicate rule handles when replacing rules, also from Florian.
6) Remove net_exit path in xt_RATEEST that results in splat, from Taehee.
7) Possible use-after-free in nft_compat when releasing extensions.
From Florian.
8) Memory leak in xt_hashlimit, from Taehee.
9) Call ip_vs_dst_notifier after ipv6_dev_notf, from Xin Long.
10) Fix cttimeout with udplite and gre, from Florian.
11) Preserve oif for IPv6 link-local generated traffic from mangle
table, from Alin Nastac.
12) Missing error handling in masquerade notifiers, from Taehee Yoo.
13) Use mutex to protect registration/unregistration of masquerade
extensions in order to prevent a race, from Taehee.
14) Incorrect condition check in tree_nodes_free(), also from Taehee.
15) Fix chain counter leak in rule replacement path, from Taehee.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
register_{netdevice/inetaddr/inet6addr}_notifier may return an error
value, this patch adds the code to handle these error paths.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When ip6_route_me_harder is invoked, it resets outgoing interface of:
- link-local scoped packets sent by neighbor discovery
- multicast packets sent by MLD host
- multicast packets send by MLD proxy daemon that sets outgoing
interface through IPV6_PKTINFO ipi6_ifindex
Link-local and multicast packets must keep their original oif after
ip6_route_me_harder is called.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In ip packet generation, pagedlen is initialized for each skb at the
start of the loop in __ip(6)_append_data, before label alloc_new_skb.
Depending on compiler options, code can be generated that jumps to
this label, triggering use of an an uninitialized variable.
In practice, at -O2, the generated code moves the initialization below
the label. But the code should not rely on that for correctness.
Fixes: 15e36f5b8e ("udp: paged allocation with gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we add a new IPv6 address, we should also join corresponding solicited-node
multicast address, unless the interface has IFF_NOARP flag, as function
addrconf_join_solict() did. But if we remove IFF_NOARP flag later, we do
not do dad and add the mcast address. So we will drop corresponding neighbour
discovery message that came from other nodes.
A typical example is after creating a ipvlan with mode l3, setting up an ipv6
address and changing the mode to l2. Then we will not be able to ping this
address as the interface doesn't join related solicited-node mcast address.
Fix it by re-doing dad when interface changed IFF_NOARP flag. Then we will add
corresponding mcast group and check if there is a duplicate address on the
network.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Reported-by: Preethi Ramachandra <preethir@juniper.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These is no need to hold dst before calling rt6_remove_exception_rt().
The call to dst_hold_safe() in ip6_link_failure() was for ip6_del_rt(),
which has been removed in Commit 93531c6743 ("net/ipv6: separate
handling of FIB entries from dst based routes"). Otherwise, it will
cause a dst leak.
This patch is to simply remove the dst_hold_safe() call before calling
rt6_remove_exception_rt() and also do the same in ip6_del_cached_rt().
It's safe, because the removal of the exception that holds its dst's
refcnt is protected by rt6_exception_lock.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Fixes: 23fb93a4d3 ("net/ipv6: Cleanup exception and cache route handling")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains the first batch of Netfilter fixes for
your net tree:
1) Fix splat with IPv6 defragmenting locally generated fragments,
from Florian Westphal.
2) Fix Incorrect check for missing attribute in nft_osf.
3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
header, from Jiri Slaby.
4) Revert map lookup in nft_numgen, this is already possible with
the existing infrastructure without this extension.
5) Fix wrong listing of set reference counter, make counter
synchronous again, from Stefano Brivio.
6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.
7) Fix allocation failure with large set, use kvcalloc().
From Andrey Ryabinin.
8) No need to disable BH when fetch ip set comment, patch from
Jozsef Kadlecsik.
9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
Taehee Yoo.
10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
from Jozsef Kadlecsik.
11) Fix setting default timeout via nfnetlink_cttimeout, this
comes with preparation patch to add nf_{tcp,udp,...}_pernet()
helper.
12) Allow ebtables table nat to be of filter type via nft_compat.
From Florian Westphal.
13) Incorrect calculation of next bucket in early_drop, do no bump
hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.
Fixes: 08e814c9e8 ("net/ipv6: Bail early if user only wants cloned entries")
Fixes: ae677bbb44 ("net: Don't return invalid table id error when dumping all families")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.
Fixes: 2384d02520 ("net/ipv6: Add anycast addresses to a global hashtable")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp6_send() function is expensive on systems with a large number of
interfaces. Every time it’s called, it has to verify that the source
address does not correspond to an existing anycast address by looping
through every device and every anycast address on the device. This can
result in significant delays for a CPU when there are a large number of
neighbors and ND timers are frequently timing out and calling
neigh_invalidate().
Add anycast addresses to a global hashtable to allow quick searching for
matching anycast addresses. This is based on inet6_addr_lst in addrconf.c.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traceroute executed in a vrf succeeds if no device is given or if the
vrf is given as the device, but fails if the interface is given as the
device. This is for default UDP probes, it succeeds for TCP SYN or ICMP
ECHO probes. As the skb bound dev is the interface and the sk dev is
the vrf, sk lookup fails for ICMP_DEST_UNREACH and ICMP_TIME_EXCEEDED
messages. The solution is for the secondary dev to be passed so that
the interface is available for the device match to succeed, in the same
way as is already done for non-error cases.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a61bbcf28a ("[NET]: Store skb->timestamp as offset to a base
timestamp") introduces a neighbour control buffer and zeroes it out in
ndisc_rcv(), as ndisc_recv_ns() uses it.
Commit f2776ff047 ("[IPV6]: Fix address/interface handling in UDP and
DCCP, according to the scoping architecture.") introduces the usage of the
IPv6 control buffer in protocol error handlers (e.g. inet6_iif() in
present-day __udp6_lib_err()).
Now, with commit b94f1c0904 ("ipv6: Use icmpv6_notify() to propagate
redirect, instead of rt6_redirect()."), we call protocol error handlers
from ndisc_redirect_rcv(), after the control buffer is already stolen and
some parts are already zeroed out. This implies that inet6_iif() on this
path will always return zero.
This gives unexpected results on UDP socket lookup in __udp6_lib_err(), as
we might actually need to match sockets for a given interface.
Instead of always claiming the control buffer in ndisc_rcv(), do that only
when needed.
Fixes: b94f1c0904 ("ipv6: Use icmpv6_notify() to propagate redirect, instead of rt6_redirect().")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cleanup path will put the target net when netnsid is set. So we must
reset netnsid if the input is invalid.
Fixes: d7e38611b8 ("net/ipv4: Put target net when address dump fails due to bad attributes")
Fixes: 242afaa696 ("net/ipv6: Put target net when address dump fails due to bad attributes")
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipv4 and normal ipv6 defrag, netfilter ipv6 defragmentation did
not save/restore skb->dst.
This causes oops when handling locally generated ipv6 fragments, as
output path needs a valid dst.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Fixes: 84379c9afe ("netfilter: ipv6: nf_defrag: drop skb dst before queueing")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The intent of ip6_route_check_nh_onlink is to make sure the gateway
given for an onlink route is not actually on a connected route for
a different interface (e.g., 2001:db8:1::/64 is on dev eth1 and then
an onlink route has a via 2001:db8:1::1 dev eth2). If the gateway
lookup hits the default route then it most likely will be a different
interface than the onlink route which is ok.
Update ip6_route_check_nh_onlink to disregard the device mismatch
if the gateway lookup hits the default route. Turns out the existing
onlink tests are passing because there is no default route or it is
an unreachable default, so update the onlink tests to have a default
route other than unreachable.
Fixes: fc1e64e109 ("net/ipv6: Add support for onlink flag")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057 ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing a route dump across all address families, do not error out
if the table does not exist. This allows a route dump for AF_UNSPEC
with a table id that may only exist for some of the families.
Do return the table does not exist error if dumping routes for a
specific family and the table does not exist.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tgt_net is set based on IFA_TARGET_NETNSID attribute in the dump
request, make sure all error paths call put_net.
Fixes: 6371a71f3a ("net/ipv6: Add support for dumping addresses for a specific device")
Fixes: ed6eff1179 ("net/ipv6: Update inet6_dump_addr for strict data checking")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an RTM_GETADDR dump request has ifa_index set in the ifaddrmsg
header, then return only the addresses for that device.
Since inet6_dump_addr is reused for multicast and anycast addresses,
this adds support for device specfic dumps of RTM_GETMULTICAST and
RTM_GETANYCAST as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_idx is always 0 going into in6_dump_addrs; it is passed as a pointer
to save the last good index into cb. Since cb is already argument to
in6_dump_addrs, just save the value there.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern's dump indexing bug fix in 'net' overlapped the
change of the function signature of inet6_fill_ifaddr() in
'net-next'. Trivially resolved.
Signed-off-by: David S. Miller <davem@davemloft.net>
The loop wants to skip previously dumped addresses, so loops until
current index >= saved index. If the message fills it wants to save
the index for the next address to dump - ie., the one that did not
fit in the current message.
Currently, it is incrementing the index counter before comparing to the
saved index, and then the saved index is off by 1 - it assumes the
current address is going to fit in the message.
Change the index handling to increment only after a succesful dump.
Fixes: 502a2ffd73 ("ipv6: convert idev_list to list macros")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 058214a4d1 ("ip6_tun: Add infrastructure for doing
encapsulation") added the ip6_tnl_encap() call in ip6_tnl_xmit(), before
the call to ipv6_push_frag_opts() to append the IPv6 Tunnel Encapsulation
Limit option (option 4, RFC 2473, par. 5.1) to the outer IPv6 header.
As long as the option didn't actually end up in generated packets, this
wasn't an issue. Then commit 89a23c8b52 ("ip6_tunnel: Fix missing tunnel
encapsulation limit option") fixed sending of this option, and the
resulting layout, e.g. for FoU, is:
.-------------------.------------.----------.-------------------.----- - -
| Outer IPv6 Header | UDP header | Option 4 | Inner IPv6 Header | Payload
'-------------------'------------'----------'-------------------'----- - -
Needless to say, FoU and GUE (at least) won't work over IPv6. The option
is appended by default, and I couldn't find a way to disable it with the
current iproute2.
Turn this into a more reasonable:
.-------------------.----------.------------.-------------------.----- - -
| Outer IPv6 Header | Option 4 | UDP header | Inner IPv6 Header | Payload
'-------------------'----------'------------'-------------------'----- - -
With this, and with 84dad55951 ("udp6: fix encap return code for
resubmitting"), FoU and GUE work again over IPv6.
Fixes: 058214a4d1 ("ip6_tun: Add infrastructure for doing encapsulation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-10-18
1) Free the xfrm interface gro_cells when deleting the
interface, otherwise we leak it. From Li RongQing.
2) net/core/flow.c does not exist anymore, so remove it
from the MAINTAINERS file.
3) Fix a slab-out-of-bounds in _decode_session6.
From Alexei Starovoitov.
4) Fix RCU protection when policies inserted into
thei bydst lists. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit eb63f2964d ("udp6: add missing checks on edumux packet
processing") used the same return code convention of the ipv4 counterpart,
but ipv6 uses the opposite one: positive values means resubmit.
This change addresses the issue, using positive return value for
resubmitting. Also update the related comment, which was broken, too.
Fixes: eb63f2964d ("udp6: add missing checks on edumux packet processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, IPv6 fib no longer contains cloned routes. If a user
requests a route dump for only cloned entries, no sense walking the FIB
and returning everything.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update parsing of route dump request to enable kernel side filtering.
Allow filtering results by protocol (e.g., which routing daemon installed
the route), route type (e.g., unicast), table id and nexthop device. These
amount to the low hanging fruit, yet a huge improvement, for dumping
routes.
ip_valid_fib_dump_req is called with RTNL held, so __dev_get_by_index can
be used to look up the device index without taking a reference. From
there filter->dev is only used during dump loops with the lock still held.
Set NLM_F_DUMP_FILTERED in the answer_flags so the user knows the results
have been filtered should no entries be returned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by egress device index and
table id. If the table id is given in the filter, lookup table and
call mr_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by table id, egress device
index, protocol, and route type. If the table id is given in the filter,
lookup the table and call fib6_dump_table directly for it.
Move the existing route flags check for prefix only routes to the new
filter.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct fib_dump_filter for options on limiting which routes are
returned in a dump request. The current list is table id, protocol,
route type, rtm_flags and nexthop device index. struct net is needed
to lookup the net_device from the index.
Declare the filter for each route dump handler and plumb the new
arguments from dump handlers to ip_valid_fib_dump_req.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Convert BPF sockmap and kTLS to both use a new sk_msg API and enable
sk_msg BPF integration for the latter, from Daniel and John.
2) Enable BPF syscall side to indicate for maps that they do not support
a map lookup operation as opposed to just missing key, from Prashant.
3) Add bpftool map create command which after map creation pins the
map into bpf fs for further processing, from Jakub.
4) Add bpftool support for attaching programs to maps allowing sock_map
and sock_hash to be used from bpftool, from John.
5) Improve syscall BPF map update/delete path for map-in-map types to
wait a RCU grace period for pending references to complete, from Daniel.
6) Couple of follow-up fixes for the BPF socket lookup to get it
enabled also when IPv6 is compiled as a module, from Joe.
7) Fix a generic-XDP bug to handle the case when the Ethernet header
was mangled and thus update skb's protocol and data, from Jesper.
8) Add a missing BTF header length check between header copies from
user space, from Wenwen.
9) Minor fixups in libbpf to use __u32 instead u32 types and include
proper perf_event.h uapi header instead of perf internal one, from Yonghong.
10) Allow to pass user-defined flags through EXTRA_CFLAGS and EXTRA_LDFLAGS
to bpftool's build, from Jiri.
11) BPF kselftest tweaks to add LWTUNNEL to config fragment and to install
with_addr.sh script from flow dissector selftest, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 270972554c ("[IPV6]: ROUTE: Add Router Reachability
Probing (RFC4191).") introduced router probing, the rt6_probe() function
required that a neighbour entry existed. This neighbour entry is used to
record the timestamp of the last probe via the ->updated field.
Later, commit 2152caea71 ("ipv6: Do not depend on rt->n in rt6_probe().")
removed the requirement for a neighbour entry. Neighbourless routes skip
the interval check and are not rate-limited.
This patch adds rate-limiting for neighbourless routes, by recording the
timestamp of the last probe in the fib6_info itself.
Fixes: 2152caea71 ("ipv6: Do not depend on rt->n in rt6_probe().")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a more complete fix than d71019b54b ("net: core: Fix build
with CONFIG_IPV6=m"), so that IPv6 sockets may be looked up if the IPv6
module is loaded (not just if it's compiled in).
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link's carrier goes down it could be a sign of the port changing
networks. If the new network has overlapping addresses with the old one,
then the kernel will continue trying to use neighbor entries established
based on the old network until the entries finally age out - meaning a
potentially long delay with communications not working.
This patch evicts neighbor entries on carrier down with the exception of
those marked permanent. Permanent entries are managed by userspace (either
an admin or a routing daemon such as FRR).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another difference between IPv4 and IPv6 is the generation of RTM_DELROUTE
notifications when a device is taken down (admin down) or deleted. IPv4
does not generate a message for routes evicted by the down or delete;
IPv6 does. A NOS at scale really needs to avoid these messages and have
IPv4 and IPv6 behave similarly, relying on userspace to handle link
notifications and evict the routes.
At this point existing user behavior needs to be preserved. Since
notifications are a global action (not per app) the only way to preserve
existing behavior and allow the messages to be skipped is to add a new
sysctl (net/ipv6/route/skip_notify_on_dev_down) which can be set to
disable the notificatioons.
IPv6 route code already supports the option to skip the message (it is
used for multipath routes for example). Besides the new sysctl we need
to pass the skip_notify setting through the generic fib6_clean and
fib6_walk functions to fib6_clean_node and to set skip_notify on calls
to __ip_del_rt for the addrconf_ifdown path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib6_info_alloc() function allocates percpu memory to hold per CPU
pointers to rt6_info, but this memory is never freed. Fix it.
Fixes: a64efe142f ("net/ipv6: introduce fib6_info struct and helpers")
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_route_table_template is exported but there are no users outside
of route.c. Make it static.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree:
1) Support for matching on ipsec policy already set in the route, from
Florian Westphal.
2) Split set destruction into deactivate and destroy phase to make it
fit better into the transaction infrastructure, also from Florian.
This includes a patch to warn on imbalance when setting the new
activate and deactivate interfaces.
3) Release transaction list from the workqueue to remove expensive
synchronize_rcu() from configuration plane path. This speeds up
configuration plane quite a bit. From Florian Westphal.
4) Add new xfrm/ipsec extension, this new extension allows you to match
for ipsec tunnel keys such as source and destination address, spi and
reqid. From Máté Eckl and Florian Westphal.
5) Add secmark support, this includes connsecmark too, patches
from Christian Gottsche.
6) Allow to specify remaining bytes in xt_quota, from Chenbo Feng.
One follow up patch to calm a clang warning for this one, from
Nathan Chancellor.
7) Flush conntrack entries based on layer 3 family, from Kristian Evensen.
8) New revision for cgroups2 to shrink the path field.
9) Get rid of obsolete need_conntrack(), as a result from recent
demodularization works.
10) Use WARN_ON instead of BUG_ON, from Florian Westphal.
11) Unused exported symbol in nf_nat_ipv4_fn(), from Florian.
12) Remove superfluous check for timeout netlink parser and dump
functions in layer 4 conntrack helpers.
13) Unnecessary redundant rcu read side locks in NAT redirect,
from Taehee Yoo.
14) Pass nf_hook_state structure to error handlers, patch from
Florian Westphal.
15) Remove ->new() interface from layer 4 protocol trackers. Place
them in the ->packet() interface. From Florian.
16) Place conntrack ->error() handling in the ->packet() interface.
Patches from Florian Westphal.
17) Remove unused parameter in the pernet initialization path,
also from Florian.
18) Remove additional parameter to specify layer 3 protocol when
looking up for protocol tracker. From Florian.
19) Shrink array of layer 4 protocol trackers, from Florian.
20) Check for linear skb only once from the ALG NAT mangling
codebase, from Taehee Yoo.
21) Use rhashtable_walk_enter() instead of deprecated
rhashtable_walk_init(), also from Taehee.
22) No need to flush all conntracks when only one single address
is gone, from Tan Hu.
23) Remove redundant check for NAT flags in flowtable code, from
Taehee Yoo.
24) Use rhashtable_lookup() instead of rhashtable_lookup_fast()
from netfilter codebase, since rcu read lock side is already
assumed in this path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update inet_netconf_dump_devconf, inet6_netconf_dump_devconf, and
mpls_netconf_dump_devconf for strict data checking. If the flag is set,
the dump request is expected to have an netconfmsg struct as the header.
The struct only has the family member and no attributes can be appended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ip6addrlbl_dump for strict data checking. If the flag is set,
the dump request is expected to have an ifaddrlblmsg struct as the
header. All elements of the struct are expected to be 0 and no
attributes can be appended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
