For implicit namespacing and clarity, prefix the common Port IEEE
Priority Remapping registers macros with MV88E6095_PORT_IEEE_PRIO.
The 88E6390 family turned the 0x18 register into a single indirect
table, document that at the same time.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Also fix the following checkpatch checks with a temporary variable:
CHECK: Alignment should match open parenthesis
#65: FILE: drivers/net/dsa/mv88e6xxx/port.c:932:
+ err = mv88e6xxx_port_ieeepmt_write(chip, port,
+ MV88E6390_PORT_IEEE_PRIO_MAP_TABLE_INGRESS_PCP,
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Association
Vector Register macros with MV88E6XXX_PORT_ASSOC_VECTOR.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Egress Rate
Control and Port Egress Rate Control 2 registers macros with
MV88E6XXX_PORT_EGRESS_RATE_CTL1 and MV88E6XXX_PORT_EGRESS_RATE_CTL2.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Control 2
Register macros with MV88E6XXX_PORT_CTL2 and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6095_PORT_CTL2_CPU_PORT_MASK.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Default
VLAN Register macros with MV88E6XXX_PORT_DEFAULT_VLAN.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Based VLAN
Register macros with MV88E6XXX_PORT_BASE_VLAN.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Control 1
Register macros with MV88E6XXX_PORT_CTL1.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Control
Register macros with MV88E6XXX_PORT_CTL0 and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6185_PORT_CTL0_USE_TAG.)
The reason for CTL0 is to make it clear between the badly named
"Port Control", "Port Control 1" and "Port Control 2" registers.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Switch ID
Register macros with MV88E6XXX_PORT_SWITCH_ID.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers, this means shifting their values by 4.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Jamming
Control Register macros with MV88E6XXX_PORT_JAM_CTL and the ones which
differ between implementations with a chosen reference model
(e.g. MV88E6097_PORT_JAM_CTL.)
The 88E6390 family renamed the register to Flow Control and turned it
into an indirect table. Document that as well.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common MAC Control
Register macros with MV88E6XXX_PORT_MAC_CTL and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6065_PORT_MAC_CTL_SPEED_200.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Status
Register macros with MV88E6XXX_PORT_STS and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6352_PORT_STS_EEE.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many situations where generic HID driver provides some basic level
of support for certain device, but later this support (usually by implementing
vendor-specific extensions of HID protocol) is extended and the support moved
over to a separate (usually per-vendor) specific driver.
This might bring a rather unpleasant suprise for users, as all of a sudden
there is a new config option they have to enable in order to get any support
for their device whatsoever, although previous kernel versions provided basic
support through the generic driver. Which is rightfully seen as a regression.
Fix this by including the entry for a particular device in
hid_have_special_driver[] iff the specific config option has been specified,
and let generic driver handle the device otherwise.
Also make the behavior of hid_scan_report() (where the same decision is being
taken on a per-report level) consistent.
While at it, reshuffle the hid_have_special_driver[] a bit to restore the
alphabetical ordering (first order by config option, and within those
sections order by VID).
This is considered a short-term solution, before generic way of giving
precedence to special drivers and falling back to generic driver is
figured out.
While at it, fixup a missing entry for GFRM driver; thanks to Hans de Geode for
spotting this (and for discovering a few issues in the conversion).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wifi driver can decide to not provide parts of the station info. For
example, the expected throughput of the station can be omitted when the
used rate control doesn't provide this kind of information.
The B.A.T.M.A.N. V implementation must therefore check the filled bitfield
before it tries to access the expected_throughput of the returned
station_info.
Reported-by: Alvaro Antelo <alvaro.antelo@gmail.com>
Fixes: c833484e5f ("batman-adv: ELP - compute the metric based on the estimated throughput")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A wifi interface should never be handled like an ethernet devices. The
parser of the cfg80211 output must therefore skip the ethtool code when
cfg80211_get_station returned an error.
Fixes: f44a3ae9a2 ("batman-adv: refactor wifi interface detection")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assingment if ->probe() fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is very useful to know what ampdu action is currently
happening. Add this information to the tracepoint.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The description of NL80211_CMD_ROAM indicated possibility for a
request to roam issued by user-space. However, it also states that
as not being implemented right now. This has been so since commit
b23aa676ab ("cfg80211: connect/disconnect API") added in 2009.
So it seems safe to assume it will not be added any time soon and
thus remove it.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that initiate roaming while being connected to a network that
uses 802.1X authentication need to inform user space if 802.1X
authentication is further required after roaming.
For example, when using the Fast transition protocol, roaming within
the mobility domain does not require new 802.1X authentication, but
roaming to another mobility domain does.
In addition, some drivers may not support 802.1X authentication
(so it has to be done in user space), while other drivers do.
Add a flag to the roaming notification to indicate if user space is
required to do 802.1X authentication after the roaming or not.
This flag will only be used for networks that use 802.1X
authentication. For networks that do not use 802.1X authentication it
is assumed that no further action is required from user space after
the roaming notification.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com reuse NL80211_ATTR_PORT_AUTHORIZED]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[rebase to apply w/o the flag in CONNECT]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API for setting the PMK to the driver. For FT support, allow
setting also the PMK-R0 Name.
This can be used by drivers that support 4-Way handshake offload
while IEEE802.1X authentication is managed by upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[arend.vanspriel@broadcom.com: add WANT_1X_4WAY_HS attribute]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X docs a bit to
say that the device may require it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let drivers advertise support for station-mode 4-way handshake
offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK flag.
Extend use of NL80211_ATTR_PMK attribute indicating it might be passed
as part of NL80211_CMD_CONNECT command, and contain the PSK (which is
the PMK, hence the name.)
The driver/device is assumed to handle the 4-way handshake by
itself in this case (including key derivations, etc.), instead
of relying on the supplicant.
This patch is somewhat based on this one (by Vladimir Kondratiev):
https://patchwork.kernel.org/patch/1309561/.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com rebase dealing with existing ATTR_PMK]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK docs to indicate
that this offload might be required]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).
This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.
Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
sdata->smps_mode = SMPS_DYNAMIC
bss->req_smps = SMPS_OFF
That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.
Fix that by properly setting bss->req_smps in
ieee80211_start_ap.
Fixes: f699317487 ("mac80211: set smps_mode according to ap params")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 changes the channel, it also calls into the driver's
bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver
may, like iwlwifi does, access more data from bss_info in that case
and iwlwifi accesses the basic_rates bitmap, but if changing from a
band with more (basic) rates to one with fewer, an out-of-bounds
access of the rate array may result.
While we can't avoid having invalid data at some point in time, we
can avoid having it while we call the driver - so set up all the
data before configuring the channel, and then apply it afterwards.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677
Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Debugged-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need for the station MLME code to handle bitrates for 5
or 10 MHz channels when it can't ever create such a configuration.
Remove the unnecessary code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver reports the rx timestamp at PLCP start, mac80211 can
only handle legacy encoding, but the code checks that the encoding
is not legacy. Fix this.
Fixes: da6a4352e7 ("mac80211: separate encoding/bandwidth from flags")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a peer sends a BAR frame with PM bit clear, we should
not modify its PM state as madated by the spec in
802.11-20012 10.2.1.2.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support;
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector;
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5lPB
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
* tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: don't use linux IRQ #0
xtensa: reduce double exception literal reservation
xtensa: ISS: Use kmalloc_array() in simdisk_init()
xtensa: Use seq_puts() in c_show()
Pull s390 fixes from Martin Schwidefsky:
- A fix for KVM to avoid kernel oopses in case of host protection
faults due to runtime instrumentation
- A fix for the AP bus to avoid dead devices after unbind / bind
- A fix for a compile warning merged from the vfio_ccw tree
- Updated default configurations
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfig
s390/zcrypt: Fix blocking queue device after unbind/bind.
s390/vfio_ccw: make some symbols static
s390/kvm: do not rely on the ILC on kvm host protection fauls
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HSR interface is setup using ip link command, an annoying warning
appears with the trace as below:-
[ 203.019828] hsr_get_node: Non-HSR frame
[ 203.019833] Modules linked in:
[ 203.019848] CPU: 0 PID: 158 Comm: sd-resolve Tainted: G W 4.12.0-rc3-00052-g9fa6bf70 #2
[ 203.019853] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 203.019869] [<c0110280>] (unwind_backtrace) from [<c010c2f4>] (show_stack+0x10/0x14)
[ 203.019880] [<c010c2f4>] (show_stack) from [<c04b9f64>] (dump_stack+0xac/0xe0)
[ 203.019894] [<c04b9f64>] (dump_stack) from [<c01374e8>] (__warn+0xd8/0x104)
[ 203.019907] [<c01374e8>] (__warn) from [<c0137548>] (warn_slowpath_fmt+0x34/0x44)
root@am57xx-evm:~# [ 203.019921] [<c0137548>] (warn_slowpath_fmt) from [<c081126c>] (hsr_get_node+0x148/0x170)
[ 203.019932] [<c081126c>] (hsr_get_node) from [<c0814240>] (hsr_forward_skb+0x110/0x7c0)
[ 203.019942] [<c0814240>] (hsr_forward_skb) from [<c0811d64>] (hsr_dev_xmit+0x2c/0x34)
[ 203.019954] [<c0811d64>] (hsr_dev_xmit) from [<c06c0828>] (dev_hard_start_xmit+0xc4/0x3bc)
[ 203.019963] [<c06c0828>] (dev_hard_start_xmit) from [<c06c13d8>] (__dev_queue_xmit+0x7c4/0x98c)
[ 203.019974] [<c06c13d8>] (__dev_queue_xmit) from [<c0782f54>] (ip6_finish_output2+0x330/0xc1c)
[ 203.019983] [<c0782f54>] (ip6_finish_output2) from [<c0788f0c>] (ip6_output+0x58/0x454)
[ 203.019994] [<c0788f0c>] (ip6_output) from [<c07b16cc>] (mld_sendpack+0x420/0x744)
As this is an expected path to hsr_get_node() with frame coming from
the master interface, add a check to ensure packet is not from the
master port and then warn.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give back all modes advertised by the link partner. This change brings
the marvell phy driver in line with all other phy drivers.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes vxlan_snoop to not move permanent fdb entries
on learn events. This is consistent with the bridge fdb
handling of permanent entries.
Fixes: 26a41ae604 ("vxlan: only migrate dynamic FDB entries")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZPpCkAAoJEG4XJFUm622bUTMH/ipenw7p7otrhw9qtSBcqBRJ
hS+1i2J+VXDXptFng0ziPWVv6mvhANvBszuOmiNMOgqjx2HrVknwlKUKViklHN3p
E1PE3/A3bRpzBjMk4j8r/Z7VJK3rDa4WSi/AMJtqV9noNm5FfiOrCk7rXm2MLBns
x1Wyr/7OX12hiB4SCoOuOZqS/TvHlNCW71BoyRruq01N2MA1iSonLCYJbovgi7Ds
9acAY90PF8jLC+o7wxYkwuRqWncNhnKOsVNhc/6DKH91zB+C5sw2NGfD3WMfot/Z
9uC5nBWNadoLGi636y+9evIRgNAFCczCZZSUeY7jMWiVn7XyFy8zoc4fv2ZSBto=
=6md1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
udp: reduce cache pressure
In the most common use case, many skb fields are not used by recvmsg(), and
the few ones actually accessed lays on cold cachelines, which leads to several
cache miss per packet.
This patch series attempts to reduce such misses with different strategies:
* caching the interesting fields in the scratched space
* avoid accessing at all uninteresting fields
* prefetching
Tested using the udp_sink program by Jesper[1] as the receiver, an h/w l4 rx
hash on the ingress nic, so that the number of ingress nic rx queues hit by the
udp traffic could be controlled via ethtool -L.
The udp_sink program was bound to the first idle cpu, to get more
stable numbers.
On a single numa node receiver:
nic rx queues vanilla patched kernel delta
1 1850 kpps 1850 kpps 0%
2 2370 kpps 2700 kpps 13.9%
16 2000 kpps 2220 kpps 11%
[1] https://github.com/netoptimizer/network-testing/blob/master/src/udp_sink.c
v1 -> v2:
- replaced secpath_reset() with skb_release_head_state()
- changed udp_dev_scratch fields types to u{32,16} variant,
replaced bitfield with bool
v2 -> v3:
- no changes, tested against apachebench for performances regression
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
when udp_recvmsg() is executed, on x86_64 and other archs, most skb
fields are on cold cachelines.
If the skb are linear and the kernel don't need to compute the udp
csum, only a handful of skb fields are required by udp_recvmsg().
Since we already use skb->dev_scratch to cache hot data, and
there are 32 bits unused on 64 bit archs, use such field to cache
as much data as we can, and try to prefetch on dequeue the relevant
fields that are left out.
This can save up to 2 cache miss per packet.
v1 -> v2:
- changed udp_dev_scratch fields types to u{32,16} variant,
replaced bitfiled with bool
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since UDP no more uses sk->destructor, we can clear completely
the skb head state before enqueuing. Amend and use
skb_release_head_state() for that.
All head states share a single cacheline, which is not
normally used/accesses on dequeue. We can avoid entirely accessing
such cacheline implementing and using in the UDP code a specialized
skb free helper which ignores the skb head state.
This saves a cacheline miss at skb deallocation time.
v1 -> v2:
replaced secpath_reset() with skb_release_head_state()
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is replicated in 3 different places; move it to a
common helper.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports the MTU to be changed and the driver it self is
somewhat prepared to support this. This patch hooks up the callbacks to
be able to change the MTU from user-space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/snmp6 yields bogus values on 32 bit kernels.
Use "u64" instead of "unsigned long" in sizeof().
Fixes: 4a4857b1c8 ("proc: Reduce cache miss in snmp6_seq_show")
Signed-off-by: Christian Perle <christian.perle@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull devfreq fixes from MyungJoo Ham.
* 'for-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mzx/devfreq:
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
'of_node_put()' should be called on pointer returned by
'of_parse_phandle()' when done. In this function this is done in all path
except this 'continue', so add it.
Fixes: 97735da074 (drivers: cpuidle: Add status property to ARM idle states)
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 27ed3cd2eb (cpufreq: conservative: Fix the logic in frequency
decrease checking) removed the 10 point substraction when comparing the
load against down_threshold but did not remove the related limit for the
down_threshold value. As a result, down_threshold lower than 11 is not
allowed even though values from 1 to 10 do work correctly too. The
comment ("cannot be lower than 11 otherwise freq will not fall") also
does not apply after removing the substraction.
For this reason, allow down_threshold to take any value from 1 to 99
and fix the related comment.
Fixes: 27ed3cd2eb (cpufreq: conservative: Fix the logic in frequency decrease checking)
Signed-off-by: Tomasz Wilczyński <twilczynski@naver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 39b64aa1c0 (cpufreq: schedutil: Reduce frequencies
slower) that introduced unintentional changes in behavior leading
to adverse effects on some systems.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Considering this case:
1. A program opens a sysfs table file 65535 times, it can increase
validation_count and first increment cause the table to be mapped:
validation_count = 65535
2. AML execution causes "Load" to be executed on the same
table, this time it cannot increase validation_count, so
validation_count remains:
validation_count = 65535
3. The program closes sysfs table file 65535 times, it can decrease
validation_count and the last decrement cause the table to be
unmapped:
validation_count = 0
4. AML code still accessing the loaded table, kernel crash can be
observed.
To prevent that from happening, add a validation_count threashold.
When it is reached, the validation_count can no longer be
incremented/decremented to invalidate the table descriptor (means
preventing table unmappings)
Note that code added in acpi_tb_put_table() is actually a no-op but
changes the warning message into a "warn once" one. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog, comments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ppmu_events array is accessed only in this compilation unit so it
can be made static.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
