There was a regression introduced by the blamed commit, where pinging to
a VLAN-unaware bridge would fail with the repeated message "Couldn't
decode source port" coming from the tagging protocol driver.
When receiving packets with a bridge_vid as determined by
dsa_tag_8021q_bridge_join(), dsa_8021q_rcv() will decode:
- source_port = 0 (which isn't really valid, more like "don't know")
- switch_id = 0 (which isn't really valid, more like "don't know")
- vbid = value in range 1-7
Since the blamed patch has reversed the order of the checks, we are now
going to believe that source_port != -1 and switch_id != -1, so they're
valid, but they aren't.
The minimal solution to the problem is to only populate source_port and
switch_id with what dsa_8021q_rcv() came up with, if the vbid is zero,
i.e. the source port information is trustworthy.
Fixes: c1ae02d876 ("net: dsa: tag_sja1105: always prefer source port information from INCL_SRCPT")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the synchronization rules for .ndo_get_stats() as seen in
Documentation/networking/netdevices.rst, acquiring a plain spin_lock()
should not be illegal, but the bridge driver implementation makes it so.
After running these commands, I am being faced with the following
lockdep splat:
$ ip link add link swp0 name macsec0 type macsec encrypt on && ip link set swp0 up
$ ip link add dev br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set macsec0 master br0 && ip link set macsec0 up
========================================================
WARNING: possible irq lock inversion dependency detected
6.4.0-04295-g31b577b4bd4a #603 Not tainted
--------------------------------------------------------
swapper/1/0 just changed the state of lock:
ffff6bd348724cd8 (&br->lock){+.-.}-{3:3}, at: br_forward_delay_timer_expired+0x34/0x198
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&ocelot->stats_lock){+.+.}-{3:3}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Chain exists of:
&br->lock --> &br->hash_lock --> &ocelot->stats_lock
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ocelot->stats_lock);
local_irq_disable();
lock(&br->lock);
lock(&br->hash_lock);
<Interrupt>
lock(&br->lock);
*** DEADLOCK ***
(details about the 3 locks skipped)
swp0 is instantiated by drivers/net/dsa/ocelot/felix.c, and this
only matters to the extent that its .ndo_get_stats64() method calls
spin_lock(&ocelot->stats_lock).
Documentation/locking/lockdep-design.rst says:
| A lock is irq-safe means it was ever used in an irq context, while a lock
| is irq-unsafe means it was ever acquired with irq enabled.
(...)
| Furthermore, the following usage based lock dependencies are not allowed
| between any two lock-classes::
|
| <hardirq-safe> -> <hardirq-unsafe>
| <softirq-safe> -> <softirq-unsafe>
Lockdep marks br->hash_lock as softirq-safe, because it is sometimes
taken in softirq context (for example br_fdb_update() which runs in
NET_RX softirq), and when it's not in softirq context it blocks softirqs
by using spin_lock_bh().
Lockdep marks ocelot->stats_lock as softirq-unsafe, because it never
blocks softirqs from running, and it is never taken from softirq
context. So it can always be interrupted by softirqs.
There is a call path through which a function that holds br->hash_lock:
fdb_add_hw_addr() will call a function that acquires ocelot->stats_lock:
ocelot_port_get_stats64(). This can be seen below:
ocelot_port_get_stats64+0x3c/0x1e0
felix_get_stats64+0x20/0x38
dsa_slave_get_stats64+0x3c/0x60
dev_get_stats+0x74/0x2c8
rtnl_fill_stats+0x4c/0x150
rtnl_fill_ifinfo+0x5cc/0x7b8
rtmsg_ifinfo_build_skb+0xe4/0x150
rtmsg_ifinfo+0x5c/0xb0
__dev_notify_flags+0x58/0x200
__dev_set_promiscuity+0xa0/0x1f8
dev_set_promiscuity+0x30/0x70
macsec_dev_change_rx_flags+0x68/0x88
__dev_set_promiscuity+0x1a8/0x1f8
__dev_set_rx_mode+0x74/0xa8
dev_uc_add+0x74/0xa0
fdb_add_hw_addr+0x68/0xd8
fdb_add_local+0xc4/0x110
br_fdb_add_local+0x54/0x88
br_add_if+0x338/0x4a0
br_add_slave+0x20/0x38
do_setlink+0x3a4/0xcb8
rtnl_newlink+0x758/0x9d0
rtnetlink_rcv_msg+0x2f0/0x550
netlink_rcv_skb+0x128/0x148
rtnetlink_rcv+0x24/0x38
the plain English explanation for it is:
The macsec0 bridge port is created without p->flags & BR_PROMISC,
because it is what br_manage_promisc() decides for a VLAN filtering
bridge with a single auto port.
As part of the br_add_if() procedure, br_fdb_add_local() is called for
the MAC address of the device, and this results in a call to
dev_uc_add() for macsec0 while the softirq-safe br->hash_lock is taken.
Because macsec0 does not have IFF_UNICAST_FLT, dev_uc_add() ends up
calling __dev_set_promiscuity() for macsec0, which is propagated by its
implementation, macsec_dev_change_rx_flags(), to the lower device: swp0.
This triggers the call path:
dev_set_promiscuity(swp0)
-> rtmsg_ifinfo()
-> dev_get_stats()
-> ocelot_port_get_stats64()
with a calling context that lockdep doesn't like (br->hash_lock held).
Normally we don't see this, because even though many drivers that can be
bridge ports don't support IFF_UNICAST_FLT, we need a driver that
(a) doesn't support IFF_UNICAST_FLT, *and*
(b) it forwards the IFF_PROMISC flag to another driver, and
(c) *that* driver implements ndo_get_stats64() using a softirq-unsafe
spinlock.
Condition (b) is necessary because the first __dev_set_rx_mode() calls
__dev_set_promiscuity() with "bool notify=false", and thus, the
rtmsg_ifinfo() code path won't be entered.
The same criteria also hold true for DSA switches which don't report
IFF_UNICAST_FLT. When the DSA master uses a spin_lock() in its
ndo_get_stats64() method, the same lockdep splat can be seen.
I think the deadlock possibility is real, even though I didn't reproduce
it, and I'm thinking of the following situation to support that claim:
fdb_add_hw_addr() runs on a CPU A, in a context with softirqs locally
disabled and br->hash_lock held, and may end up attempting to acquire
ocelot->stats_lock.
In parallel, ocelot->stats_lock is currently held by a thread B (say,
ocelot_check_stats_work()), which is interrupted while holding it by a
softirq which attempts to lock br->hash_lock.
Thread B cannot make progress because br->hash_lock is held by A. Whereas
thread A cannot make progress because ocelot->stats_lock is held by B.
When taking the issue at face value, the bridge can avoid that problem
by simply making the ports promiscuous from a code path with a saner
calling context (br->hash_lock not held). A bridge port without
IFF_UNICAST_FLT is going to become promiscuous as soon as we call
dev_uc_add() on it (which we do unconditionally), so why not be
preemptive and make it promiscuous right from the beginning, so as to
not be taken by surprise.
With this, we've broken the links between code that holds br->hash_lock
or br->lock and code that calls into the ndo_change_rx_flags() or
ndo_get_stats64() ops of the bridge port.
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Kelam says:
====================
octeontx2-af: MAC block fixes for CN10KB
This patch set contains fixes for the issues encountered in testing
CN10KB MAC block RPM_USX.
Patch1: firmware to kernel communication is not working due to wrong
interrupt configuration. CSR addresses are corrected.
Patch2: NIX to RVU PF mapping errors encountered due to wrong firmware
config. Corrects this mapping error.
Patch3: Driver is trying to access non exist cgx/lmac which is resulting
in kernel panic. Address this issue by adding proper checks.
Patch4: MAC features are not getting reset on FLR. Fix the issue by
resetting the stale config.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
AF driver configures MAC features like internal loopback and PFC upon
receiving the request from PF and its VF netdev. But these
features are not getting reset in FLR. This patch fixes the issue by
resetting the same.
Fixes: 23999b30ae ("octeontx2-af: Enable or disable CGX internal loopback")
Fixes: 1121f6b02e ("octeontx2-af: Priority flow control configuration support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with the addition of new MAC blocks like CN10K RPM and CN10KB
RPM_USX, LMACs are noncontiguous and CGX blocks are also
noncontiguous. But during RVU driver initialization, the driver
is assuming they are contiguous and trying to access
cgx or lmac with their id which is resulting in kernel panic.
This patch fixes the issue by adding proper checks.
[ 23.219150] pc : cgx_lmac_read+0x38/0x70
[ 23.219154] lr : rvu_program_channels+0x3f0/0x498
[ 23.223852] sp : ffff000100d6fc80
[ 23.227158] x29: ffff000100d6fc80 x28: ffff00010009f880 x27:
000000000000005a
[ 23.234288] x26: ffff000102586768 x25: 0000000000002500 x24:
fffffffffff0f000
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware configures NIX block mapping for all MAC blocks.
The current implementation reads the configuration and
creates the mapping between RVU PF and NIX blocks. But
this configuration is only valid for silicons that support
multiple blocks. For all other silicons, all MAC blocks
map to NIX0.
This patch corrects the mapping by adding a check for the same.
Fixes: c5a73b632b ("octeontx2-af: Map NIX block from CGX connection")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current design is that, for asynchronous events like link_up and
link_down firmware raises the interrupt to kernel. The previous patch
which added RPM_USX driver has a bug where it uses old csr addresses
for configuring interrupts. Which is resulting in losing interrupts
from source firmware.
This patch fixes the issue by correcting csr addresses.
Fixes: b9d0fedc62 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a comma that should be a semicolon. The comma is at the end of an
if-body and thus makes the statement after (a bvec_set_page()) conditional
too, resulting in an oops because we didn't fill out the bio_vec[]:
BUG: kernel NULL pointer dereference, address: 0000000000000008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
...
Workqueue: nvme_tcp_wq nvme_tcp_io_work [nvme_tcp]
RIP: 0010:skb_splice_from_iter+0xf1/0x370
...
Call Trace:
tcp_sendmsg_locked+0x3a6/0xdd0
tcp_sendmsg+0x31/0x50
inet_sendmsg+0x47/0x80
sock_sendmsg+0x99/0xb0
nvme_tcp_try_send_data+0x149/0x490 [nvme_tcp]
nvme_tcp_try_send+0x1b7/0x300 [nvme_tcp]
nvme_tcp_io_work+0x40/0xc0 [nvme_tcp]
process_one_work+0x21c/0x430
worker_thread+0x54/0x3e0
kthread+0xf8/0x130
Fixes: 7769887817 ("nvme-tcp: Use sendmsg(MSG_SPLICE_PAGES) rather then sendpage")
Reported-by: Aurelien Aptel <aaptel@nvidia.com>
Link: https://lore.kernel.org/r/253mt0il43o.fsf@mtr-vdi-124.i-did-not-set--mail-host-address--so-tickle-me/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Sagi Grimberg <sagi@grimberg.me>
cc: Willem de Bruijn <willemb@google.com>
cc: Keith Busch <kbusch@kernel.org>
cc: Jens Axboe <axboe@fb.com>
cc: Christoph Hellwig <hch@lst.de>
cc: Chaitanya Kulkarni <kch@nvidia.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-nvme@lists.infradead.org
cc: netdev@vger.kernel.org
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
source.codeaurora.org is no longer accessible and so the reference link
in the documentation is not useful. Use iproute2 instead as it has a
rmnet module for configuration.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com>
Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reword slightly now that all MAINTAINERS have access to the commands.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CDC-ECM support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In CDC-ECM mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The line cards array is not freed in the error path of
mlxsw_m_linecards_init(), which can lead to a memory leak. Fix by
freeing the array in the error path, thereby making the error path
identical to mlxsw_m_linecards_fini().
Fixes: 01328e23a4 ("mlxsw: minimal: Extend module to port mapping with slot index")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230630012647.1078002-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch in MAXLEN register stores the maximum size of a data frame.
The MTU size is 18 bytes smaller than the frame size.
The current settings are causing problems with packet forwarding.
This patch fixes the MTU settings to proper values.
Fixes: fb77ffc6ec ("net: dsa: vsc73xx: make the MTU configurable")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230628194327.1765644-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All ibmvnic resets, make a call to netdev_tx_reset_queue() when
re-opening the device. netdev_tx_reset_queue() resets the num_queued
and num_completed byte counters. These stats are used in Byte Queue
Limit (BQL) algorithms. The difference between these two stats tracks
the number of bytes currently sitting on the physical NIC. ibmvnic
increases the number of queued bytes though calls to
netdev_tx_sent_queue() in the drivers xmit function. When, VIOS reports
that it is done transmitting bytes, the ibmvnic device increases the
number of completed bytes through calls to netdev_tx_completed_queue().
It is important to note that the driver batches its transmit calls and
num_queued is increased every time that an skb is added to the next
batch, not necessarily when the batch is sent to VIOS for transmission.
Unlike other reset types, a NON FATAL reset will not flush the sub crq
tx buffers. Therefore, it is possible for the batched skb array to be
partially full. So if there is call to netdev_tx_reset_queue() when
re-opening the device, the value of num_queued (0) would not account
for the skb's that are currently batched. Eventually, when the batch
is sent to VIOS, the call to netdev_tx_completed_queue() would increase
num_completed to a value greater than the num_queued. This causes a
BUG_ON crash:
ibmvnic 30000002: Firmware reports error, cause: adapter problem.
Starting recovery...
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:27!
Oops: Exception in kernel mode, sig: 5
[....]
NIP dql_completed+0x28/0x1c0
LR ibmvnic_complete_tx.isra.0+0x23c/0x420 [ibmvnic]
Call Trace:
ibmvnic_complete_tx.isra.0+0x3f8/0x420 [ibmvnic] (unreliable)
ibmvnic_interrupt_tx+0x40/0x70 [ibmvnic]
__handle_irq_event_percpu+0x98/0x270
---[ end trace ]---
Therefore, do not reset the dql stats when performing a NON_FATAL reset.
Fixes: 0d97338818 ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On systems without MAE permission efx->mae is not initialised,
and trying to lookup an mport results in a NULL pointer
dereference.
Fixes: 25414b2a64 ("sfc: add devlink port support for ef100")
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ISO Interval on CIS Established Event uses 1.25 ms slots:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 2304:
Time = N * 1.25 ms
In addition to that this always update the QoS settings based on CIS
Established Event.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use kmemdup rather than duplicating its implementation.
./net/bluetooth/hci_conn.c:1880:7-14: WARNING opportunity for kmemdup.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5597
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adding the device ID from the Asus Ally gets the bluetooth working
on the device.
Signed-off-by: Matthew Anderson <ruinairas1992@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the driver core allows for struct class to be in read-only
memory, move the bt_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This rework sync_interval to be sync_factor as having sync_interval in
the order of seconds is sometimes not disarable.
Wit sync_factor the application can tell how many SDU intervals it wants
to send an announcement with PA, the EA interval is set to 2 times that
so a factor of 24 of BIG SDU interval of 10ms would look like the
following:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x01
Properties: 0x0000
Min advertising interval: 480.000 msec (0x0300)
Max advertising interval: 480.000 msec (0x0300)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: Host has no preference (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 2M (0x02)
SID: 0x00
Scan request notifications: Disabled (0x00)
< HCI Command: LE Set Periodic Advertising Parameters (0x08|0x003e) plen 7
Handle: 1
Min interval: 240.00 msec (0x00c0)
Max interval: 240.00 msec (0x00c0)
Properties: 0x0000
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When receiving a scan response there is no way to know if the remote
device is connectable or not, so when it cannot be merged don't
make any assumption and instead just mark it with a new flag defined as
MGMT_DEV_FOUND_SCAN_RSP so userspace can tell it is a standalone
SCAN_RSP.
Link: https://lore.kernel.org/linux-bluetooth/CABBYNZ+CYMsDSPTxBn09Js3BcdC-x7vZFfyLJ3ppZGGwJKmUTw@mail.gmail.com/
Fixes: c70a7e4cc8 ("Bluetooth: Add support for Not Connectable flag for Device Found events")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the event has error status, return right error code and don't show
incorrect "response malformed" messages.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When reconfiguring CIG after disconnection of the last CIS, LE Remove
CIG shall be sent before LE Set CIG Parameters. Otherwise, it fails
because CIG is in the inactive state and not configurable (Core v5.3
Vol 6 Part B Sec. 4.5.14.3). This ordering is currently wrong under
suitable timing conditions, because LE Remove CIG is sent via the
hci_sync queue and may be delayed, but Set CIG Parameters is via
hci_send_cmd.
Make the ordering well-defined by sending also Set CIG Parameters via
hci_sync.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom driver has so far been setting this
flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag. Use this flag to indicate
when the address can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/lkml/ecef83c8-497f-4011-607b-a63c24764867@samsung.com
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devices that lack persistent storage for the device address can indicate
this by setting the HCI_QUIRK_INVALID_BDADDR which causes the controller
to be marked as unconfigured until user space has set a valid address.
The related HCI_QUIRK_USE_BDADDR_PROPERTY was later added to similarly
indicate that the device lacks a valid address but that one may be
specified in the devicetree.
As is clear from commit 7a0e5b15ca ("Bluetooth: Add quirk for reading
BD_ADDR from fwnode property") that added and documented this quirk and
commits like de79a9df16 ("Bluetooth: btqcomsmd: use
HCI_QUIRK_USE_BDADDR_PROPERTY"), the device address of controllers with
this flag should be treated as invalid until user space has had a chance
to configure the controller in case the devicetree property is missing.
As it does not make sense to allow controllers with invalid addresses,
restore the original semantics, which also makes sure that the
implementation is consistent (e.g. get_missing_options() indicates that
the address must be set) and matches the documentation (including
comments in the code, such as, "In case any of them is set, the
controller has to start up as unconfigured.").
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devices that lack persistent storage for the device address can indicate
this by setting the HCI_QUIRK_INVALID_BDADDR which causes the controller
to be marked as unconfigured until user space has set a valid address.
Once configured, the device address must be set on every setup for
controllers with HCI_QUIRK_NON_PERSISTENT_SETUP to avoid marking the
controller as unconfigured and requiring the address to be set again.
Fixes: 740011cfe9 ("Bluetooth: Add new quirk for non-persistent setup settings")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix potential use-after-free in l2cap_le_command_rej.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use le32_to_cpu for ver.soc_id to fix the following
sparse warning.
drivers/bluetooth/btqca.c:640:24: sparse: warning: restricted
__le32 degrades to integer
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing MODULE_FIRMWARE declarations for firmware referenced in
btrtl.c.
Signed-off-by: Dan Gora <dan.gora@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes a bug where on the M1 mac mini initramfs-tools fails to
include the necessary firmware into the initrd.
Fixes: c4dab50697 ("tg3: Download 57766 EEE service patch firmware")
Signed-off-by: Tobias Heider <me@tobhe.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/ZJt7LKzjdz8+dClx@tobhe.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Fix PTP received on wrong port with bridged SJA1105 DSA
Since the changes were made to tag_8021q to support imprecise RX for
bridged ports, the tag_sja1105 driver still prefers the source port
information deduced from the VLAN headers for link-local traffic, even
though the switch can theoretically do better and report the precise
source port.
The problem is that the tagger doesn't know when to trust one source of
information over another, because the INCL_SRCPT option (to "tag" link
local frames) is sometimes enabled and sometimes it isn't.
The first patch makes the switch provide the hardware tag for link local
traffic under all circumstances, and the second patch makes the tagger
always use that hardware tag as primary source of information for link
local packets.
====================
Link: https://lore.kernel.org/r/20230627094207.3385231-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently the sja1105 tagging protocol prefers using the source port
information from the VLAN header if that is available, falling back to
the INCL_SRCPT option if it isn't. The VLAN header is available for all
frames except for META frames initiated by the switch (containing RX
timestamps), and thus, the "if (is_link_local)" branch is practically
dead.
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port. With incorrect
source port reporting, for example PTP traffic over 2 bridged ports will
all be seen on sockets opened on the first such port, which is incorrect.
Now that the tagging protocol has been changed to make link-local frames
always contain source port information, we can reverse the order of the
checks so that we always give precedence to that information (which is
always precise) in lieu of the tag_8021q VID which is only precise for a
standalone port.
Fixes: d7f9787a76 ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fc ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link-local traffic on bridged SJA1105 ports is sometimes tagged by the
hardware with source port information (when the port is under a VLAN
aware bridge).
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port.
Modify the driver logic (and therefore: the tagging protocol itself) to
always include the source port information with link-local packets,
regardless of whether the port is standalone, under a VLAN-aware or
VLAN-unaware bridge. This makes it possible for the tagging driver to
give priority to that information over the tag_8021q VLAN header.
The big drawback with INCL_SRCPT is that it makes it impossible to
distinguish between an original MAC DA of 01:80:C2:XX:YY:ZZ and
01:80:C2:AA:BB:ZZ, because the tagger just patches MAC DA bytes 3 and 4
with zeroes. Only if PTP RX timestamping is enabled, the switch will
generate a META follow-up frame containing the RX timestamp and the
original bytes 3 and 4 of the MAC DA. Those will be used to patch up the
original packet. Nonetheless, in the absence of PTP RX timestamping, we
have to live with this limitation, since it is more important to have
the more precise source port information for link-local traffic.
Fixes: d7f9787a76 ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fc ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Vladimir Oltean says:
====================
Fix PTP packet drops with ocelot-8021q DSA tag protocol
Changes in v2:
- Distinguish between L2 and L4 PTP packets
v1 at:
https://lore.kernel.org/netdev/20230626154003.3153076-1-vladimir.oltean@nxp.com/
Patch 3/3 fixes an issue with the ocelot/felix driver, where it would
drop PTP traffic on RX unless hardware timestamping for that packet type
was enabled.
Fixing that requires the driver to know whether it had previously
configured the hardware to timestamp PTP packets on that port. But it
cannot correctly determine that today using the existing code structure,
so patches 1/3 and 2/3 fix the control path of the code such that
ocelot->ports[port]->trap_proto faithfully reflects whether that
configuration took place.
====================
Link: https://lore.kernel.org/r/20230627163114.3561597-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver implements a workaround for the fact that it doesn't have an
IRQ source to tell it whether PTP frames are available through the
extraction registers, for those frames to be processed and passed
towards the network stack. That workaround is to configure the switch,
through felix_hwtstamp_set() -> felix_update_trapping_destinations(),
to create two copies of PTP packets: one sent over Ethernet to the DSA
master, and one to be consumed through the aforementioned CPU extraction
queue registers.
The reason why we want PTP packets to be consumed through the CPU
extraction registers in the first place is because we want to see their
hardware RX timestamp. With tag_8021q, that is only visible that way,
and it isn't visible with the copy of the packet that's transmitted over
Ethernet.
The problem with the workaround implementation is that it drops the
packet received over Ethernet, in expectation of its copy being present
in the CPU extraction registers. However, if felix_hwtstamp_set() hasn't
run (aka PTP RX timestamping is disabled), the driver will drop the
original PTP frame and there will be no copy of it in the CPU extraction
registers. So, the network stack will simply not see any PTP frame.
Look at the port's trapping configuration to see whether the driver has
previously enabled the CPU extraction registers. If it hasn't, just
don't RX timestamp the frame and let it be passed up the stack by DSA,
which is perfectly fine.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In a future change, the driver will need to determine whether PTP RX
timestamping is enabled on a port (including whether traps were set up
on that port in particular) and that is currently not possible.
The driver supports different RX filters (L2, L4) and kinds of TX
timestamping (one-step, two-step) on its ports, but it saves all
configuration in a single struct hwtstamp_config that is global to the
switch. So, the latest timestamping configuration on one port
(including a request to disable timestamping) affects what gets reported
for all ports, even though the configuration itself is still individual
to each port.
The port timestamping configurations are only coupled because of the
common structure, so replace the hwtstamp_config with a mask of trapped
protocols saved per port. We also have the ptp_cmd to distinguish
between one-step and two-step PTP timestamping, so with those 2 bits of
information we can fully reconstruct a descriptive struct
hwtstamp_config for each port, during the SIOCGHWTSTAMP ioctl.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
PTP RX timestamping should be enabled when the user requests it, not by
default. If it is enabled by default, it can be problematic when the
ocelot driver is a DSA master, and it sidesteps what DSA tries to avoid
through __dsa_master_hwtstamp_validate().
Additionally, after the change which made ocelot trap PTP packets only
to the CPU at ocelot_hwtstamp_set() time, it is no longer even true that
RX timestamping is enabled by default, because until ocelot_hwtstamp_set()
is called, the PTP traps are actually not set up. So the rx_filter field
of ocelot->hwtstamp_config reflects an incorrect reality.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Florian Westphal says:
====================
net/sched: act_ipt bug fixes
v3: prefer skb_header() helper in patch 2. No other changes.
I've retained Acks and RvB-Tags of v2.
While checking if netfilter could be updated to replace selected
instances of NF_DROP with kfree_skb_reason+NF_STOLEN to improve
debugging info via drop monitor I found that act_ipt is incompatible
with such an approach. Moreover, it lacks multiple sanity checks
to avoid certain code paths that make assumptions that the tc layer
doesn't meet, such as header sanity checks, availability of skb_dst,
skb_nfct() and so on.
act_ipt test in the tc selftest still pass with this applied.
I think that we should consider removal of this module, while
this should take care of all problems, its ipv4 only and I don't
think there are any netfilter targets that lack a native tc
equivalent, even when ignoring bpf.
====================
Link: https://lore.kernel.org/r/20230627123813.3036-1-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xtables relies on skb being owned by ip stack, i.e. with ipv4
check in place skb->cb is supposed to be IPCB.
I don't see an immediate problem (REJECT target cannot be used anymore
now that PRE/POSTROUTING hook validation has been fixed), but better be
safe than sorry.
A much better patch would be to either mark act_ipt as
"depends on BROKEN" or remove it altogether. I plan to do this
for -next in the near future.
This tc extension is broken in the sense that tc lacks an
equivalent of NF_STOLEN verdict.
With NF_STOLEN, target function takes complete ownership of skb, caller
cannot dereference it anymore.
ACT_STOLEN cannot be used for this: it has a different meaning, caller
is allowed to dereference the skb.
At this time NF_STOLEN won't be returned by any targets as far as I can
see, but this may change in the future.
It might be possible to work around this via list of allowed
target extensions known to only return DROP or ACCEPT verdicts, but this
is error prone/fragile.
Existing selftest only validates xt_LOG and act_ipt is restricted
to ipv4 so I don't think this action is used widely.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Netfilter targets make assumptions on the skb state, for example
iphdr is supposed to be in the linear area.
This is normally done by IP stack, but in act_ipt case no
such checks are made.
Some targets can even assume that skb_dst will be valid.
Make a minimum effort to check for this:
- Don't call the targets eval function for non-ipv4 skbs.
- Don't call the targets eval function for POSTROUTING
emulation when the skb has no dst set.
v3: use skb_protocol helper (Davide Caratti)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Looks like "tc" hard-codes "mangle" as the only supported table
name, but on kernel side there are no checks.
This is wrong. Not all xtables targets are safe to call from tc.
E.g. "nat" targets assume skb has a conntrack object assigned to it.
Normally those get called from netfilter nat core which consults the
nat table to obtain the address mapping.
"tc" userspace either sets PRE or POSTROUTING as hook number, but there
is no validation of this on kernel side, so update netlink policy to
reject bogus numbers. Some targets may assume skb_dst is set for
input/forward hooks, so prevent those from being used.
act_ipt uses the hook number in two places:
1. the state hook number, this is fine as-is
2. to set par.hook_mask
The latter is a bit mask, so update the assignment to make
xt_check_target() to the right thing.
Followup patch adds required checks for the skb/packet headers before
calling the targets evaluation function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As &net->sctp.addr_wq_lock is also acquired by the timer
sctp_addr_wq_timeout_handler() in protocal.c, the same lock acquisition
at sctp_auto_asconf_init() seems should disable irq since it is called
from sctp_accept() under process context.
Possible deadlock scenario:
sctp_accept()
-> sctp_sock_migrate()
-> sctp_auto_asconf_init()
-> spin_lock(&net->sctp.addr_wq_lock)
<timer interrupt>
-> sctp_addr_wq_timeout_handler()
-> spin_lock_bh(&net->sctp.addr_wq_lock); (deadlock here)
This flaw was found using an experimental static analysis tool we are
developing for irq-related deadlock.
The tentative patch fix the potential deadlock by spin_lock_bh().
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Fixes: 34e5b01186 ("sctp: delay auto_asconf init until binding the first addr")
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20230627120340.19432-1-dg573847474@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
dev_set_rx_mode() grabs a spin_lock, and the lan743x implementation
proceeds subsequently to go to sleep using readx_poll_timeout().
Introduce a helper wrapping the readx_poll_timeout_atomic() function
and use it to replace the calls to readx_polL_timeout().
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Cc: stable@vger.kernel.org
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230627035000.1295254-1-moritzf@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Core
----
- Rework the sendpage & splice implementations. Instead of feeding
data into sockets page by page extend sendmsg handlers to support
taking a reference on the data, controlled by a new flag called
MSG_SPLICE_PAGES. Rework the handling of unexpected-end-of-file
to invoke an additional callback instead of trying to predict what
the right combination of MORE/NOTLAST flags is.
Remove the MSG_SENDPAGE_NOTLAST flag completely.
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid.
- Enable socket busy polling with CONFIG_RT.
- Improve reliability and efficiency of reporting for ref_tracker.
- Auto-generate a user space C library for various Netlink families.
Protocols
---------
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2].
- Use per-VMA locking for "page-flipping" TCP receive zerocopy.
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags.
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative.
- Create a new MPTCP getsockopt to retrieve all info (MPTCP_FULL_INFO).
- Avoid waking up applications using TLS sockets until we have
a full record.
- Allow using kernel memory for protocol ioctl callbacks, paving
the way to issuing ioctls over io_uring.
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address.
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch.
- PPPoE: make number of hash bits configurable.
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig).
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge).
- Support matching on Connectivity Fault Management (CFM) packets.
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug.
- HSR: don't enable promiscuous mode if device offloads the proto.
- Support active scanning in IEEE 802.15.4.
- Continue work on Multi-Link Operation for WiFi 7.
BPF
---
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used,
or in fact passing the verifier at all for complex programs,
especially those using open-coded iterators.
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what
the output buffer *should* be, without writing anything.
- Accept dynptr memory as memory arguments passed to helpers.
- Add routing table ID to bpf_fib_lookup BPF helper.
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands.
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only).
- Show target_{obj,btf}_id in tracing link fdinfo.
- Addition of several new kfuncs (most of the names are self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter
---------
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value.
- Increase ip_vs_conn_tab_bits range for 64BIT builds.
- Allow updating size of a set.
- Improve NAT tuple selection when connection is closing.
Driver API
----------
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out).
- Support configuring rate selection pins of SFP modules.
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines.
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer.
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio).
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message.
- Split devlink instance and devlink port operations.
New hardware / drivers
----------------------
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers
-------
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is
a variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split
the different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and
Enhanced MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9i4I
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
The changes queued up for v6.5-rc1 for sysctl are in line with
prior efforts to stop usage of deprecated routines which incur
recursion and also make it hard to remove the empty array element
in each sysctl array declaration. The most difficult user to modify
was parport which required a bit of re-thinking of how to declare shared
sysctls there, Joel Granados has stepped up to the plate to do most of
this work and eventual removal of register_sysctl_table(). That work
ended up saving us about 1465 bytes according to bloat-o-meter. Since
we gained a few bloat-o-meter karma points I moved two rather small
sysctl arrays from kernel/sysctl.c leaving us only two more sysctl
arrays to move left.
Most changes have been tested on linux-next for about a month. The last
straggler patches are a minor parport fix, changes to the sysctl
kernel selftest so to verify correctness and prevent regressions for
the future change he made to provide an alternative solution for the
special sysctl mount point target which was using the now deprecated
sysctl child element.
This is all prep work to now finally be able to remove the empty
array element in all sysctl declarations / registrations which is
expected to save us a bit of bytes all over the kernel. That work
will be tested early after v6.5-rc1 is out.
-----BEGIN PGP SIGNATURE-----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=sXUU
-----END PGP SIGNATURE-----
Merge tag 'v6.5-rc1-sysctl-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull sysctl updates from Luis Chamberlain:
"The changes for sysctl are in line with prior efforts to stop usage of
deprecated routines which incur recursion and also make it hard to
remove the empty array element in each sysctl array declaration.
The most difficult user to modify was parport which required a bit of
re-thinking of how to declare shared sysctls there, Joel Granados has
stepped up to the plate to do most of this work and eventual removal
of register_sysctl_table(). That work ended up saving us about 1465
bytes according to bloat-o-meter. Since we gained a few bloat-o-meter
karma points I moved two rather small sysctl arrays from
kernel/sysctl.c leaving us only two more sysctl arrays to move left.
Most changes have been tested on linux-next for about a month. The
last straggler patches are a minor parport fix, changes to the sysctl
kernel selftest so to verify correctness and prevent regressions for
the future change he made to provide an alternative solution for the
special sysctl mount point target which was using the now deprecated
sysctl child element.
This is all prep work to now finally be able to remove the empty array
element in all sysctl declarations / registrations which is expected
to save us a bit of bytes all over the kernel. That work will be
tested early after v6.5-rc1 is out"
* tag 'v6.5-rc1-sysctl-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
sysctl: replace child with an enumeration
sysctl: Remove debugging dump_stack
test_sysclt: Test for registering a mount point
test_sysctl: Add an option to prevent test skip
test_sysctl: Add an unregister sysctl test
test_sysctl: Group node sysctl test under one func
test_sysctl: Fix test metadata getters
parport: plug a sysctl register leak
sysctl: move security keys sysctl registration to its own file
sysctl: move umh sysctl registration to its own file
signal: move show_unhandled_signals sysctl to its own file
sysctl: remove empty dev table
sysctl: Remove register_sysctl_table
sysctl: Refactor base paths registrations
sysctl: stop exporting register_sysctl_table
parport: Removed sysctl related defines
parport: Remove register_sysctl_table from parport_default_proc_register
parport: Remove register_sysctl_table from parport_device_proc_register
parport: Remove register_sysctl_table from parport_proc_register
parport: Move magic number "15" to a define
The changes queued up for v6.5-rc1 for modules are pretty tame, mostly
code removal of moving of code. Only two minor functional changes are
made, the only one which stands out is Sebastian Andrzej Siewior's
simplification of module reference counting by removing preempt_disable()
and that has been tested on linux-next for well over a month without
no regressions. I'm now, I guess, also a kitchen sink for some kallsyms
changes.
-----BEGIN PGP SIGNATURE-----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=gjKD
-----END PGP SIGNATURE-----
Merge tag 'v6.5-rc1-modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
"The changes queued up for modules are pretty tame, mostly code removal
of moving of code.
Only two minor functional changes are made, the only one which stands
out is Sebastian Andrzej Siewior's simplification of module reference
counting by removing preempt_disable() and that has been tested on
linux-next for well over a month without no regressions.
I'm now, I guess, also a kitchen sink for some kallsyms changes"
[ There was a mis-communication about the concurrent module load changes
that I had expected to come through Luis despite me authoring the
patch. So some of the module updates were left hanging in the email
ether, and I just committed them separately.
It's my bad - I should have made it more clear that I expected my
own patches to come through the module tree too. Now they missed
linux-next, but hopefully that won't cause any issues - Linus ]
* tag 'v6.5-rc1-modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
kallsyms: make kallsyms_show_value() as generic function
kallsyms: move kallsyms_show_value() out of kallsyms.c
kallsyms: remove unsed API lookup_symbol_attrs
kallsyms: remove unused arch_get_kallsym() helper
module: Remove preempt_disable() from module reference counting.
This is the new-and-improved attempt at avoiding huge memory load spikes
when the user space boot sequence tries to load hundreds (or even
thousands) of redundant duplicate modules in parallel.
See commit 9828ed3f69 ("module: error out early on concurrent load of
the same module file") for background and an earlier failed attempt that
was reverted.
That earlier attempt just said "concurrently loading the same module is
silly, just open the module file exclusively and return -ETXTBSY if
somebody else is already loading it".
While it is true that concurrent module loads of the same module is
silly, the reason that earlier attempt then failed was that the
concurrently loaded module would often be a prerequisite for another
module.
Thus failing to load the prerequisite would then cause cascading
failures of the other modules, rather than just short-circuiting that
one unnecessary module load.
At the same time, we still really don't want to load the contents of the
same module file hundreds of times, only to then wait for an eventually
successful load, and have everybody else return -EEXIST.
As a result, this takes another approach, and treats concurrent module
loads from the same file as "idempotent" in the inode. So if one module
load is ongoing, we don't start a new one, but instead just wait for the
first one to complete and return the same return value as it did.
So unlike the first attempt, this does not return early: the intent is
not to speed up the boot, but to avoid a thundering herd problem in
allocating memory (both physical and virtual) for a module more than
once.
Also note that this does change behavior: it used to be that when you
had concurrent loads, you'd have one "winner" that would return success,
and everybody else would return -EEXIST.
In contrast, this idempotent logic goes all Oprah on the problem, and
says "You are a winner! And you are a winner! We are ALL winners". But
since there's no possible actual real semantic difference between "you
loaded the module" and "somebody else already loaded the module", this
is more of a feel-good change than an actual honest-to-goodness semantic
change.
Of course, any true Johnny-come-latelies that don't get caught in the
concurrency filter will still return -EEXIST. It's no different from
not even getting a seat at an Oprah taping. That's life.
See the long thread on the kernel mailing list about this all, which
includes some numbers for memory use before and after the patch.
Link: https://lore.kernel.org/lkml/20230524213620.3509138-1-mcgrof@kernel.org/
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Johan Hovold <johan@kernel.org>
Tested-by: Luis Chamberlain <mcgrof@kernel.org>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Rudi Heitbaum <rudi@heitbaum..com>
Tested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
