New driver for the Amiga 4000T built-in NCR53c710 SCSI controller, using the
53c700 SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the MVME16x NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the BVME6000 NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use new esp_scsi for JAZZ SCSI host adapter driver
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been more than enough time now to try to get the new m68k drivers
into the tree. Let's remove the old ones and we can remerge the new
glue once it's ready. Given that there are patches to rename two out
of the three drivers in m68k CVS and all of them need a lot of
codingstyle love anyway that's probably the better strategy to begin
with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kars de Jong <jongk@linux-m68k.org>
Cc: linux-m68k@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use new esp_scsi for JAZZ SCSI host adapter driver
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Major features:
1) Tagged queuing support.
2) Will properly negotiate for synchronous transfers even on
devices that reject the wide negotiation message, such as
CDROMs
3) Significantly lower kernel stack usage in interrupt
handler path by elimination of function vector arrays,
replaced by a top-level switch statement state machine.
4) Uses generic scsi infrastructure as much as possible to
avoid code duplication.
5) Automatic request of sense data in response to CHECK_CONDITION
6) Portable to other platforms using ESP such as DEC and Sun3
systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently scsi_wait_scan is only built modular if SCSI is modular.
However, it's perfectly possible for a built in SCSI still to have
modular drivers and thus need scsi_wait_scan as a module. Therefore,
scsi_wait_scan should always be built as a module (unless the kernel
doesn't support modules).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is IBM Virtual SCSI target driver for tgt. The driver is based on
the original ibmvscsis driver:
http://lkml.org/lkml/2005/10/17/99
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsrp provides helper functions for SRP target drivers.
Some SRP target drivers would be out of drivers/scsi/ so we added an
entry for libsrp in drivers/scsi/Kconfig.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Makefile and Kconfig for tgt.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since it often takes around 20-30 seconds to scan a scsi bus, it's
highly advantageous to do this in parallel with other things. The bulk
of this patch is ensuring that devices don't change numbering, and that
all devices are discovered prior to trying to start init. For those
who build SCSI as modules, there's a new scsi_wait_scan module that will
ensure all bus scans are finished.
This patch only handles drivers which call scsi_scan_host. Fibre Channel,
SAS, SATA, USB and Firewire all need additional work.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch formally adds support for the posting of FC events via netlink.
It is a followup to the original RFC at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114530667923464&w=2
and the initial posting at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115507374832500&w=2
The patch has been updated to optimize the send path, per the discussions
in the initial posting.
Per discussions at the Storage Summit and at OLS, we are to use netlink for
async events from transports. Also per discussions, to avoid a netlink
protocol per transport, I've create a single NETLINK_SCSITRANSPORT protocol,
which can then be used by all transports.
This patch:
- Creates new files scsi_netlink.c and scsi_netlink.h, which contains the
single and shared definitions for the SCSI Transport. It is tied into the
base SCSI subsystem intialization.
Contains a single interface routine, scsi_send_transport_event(), for a
transport to send an event (via multicast to a protocol specific group).
- Creates a new scsi_netlink_fc.h file, which contains the FC netlink event
messages
- Adds 3 new routines to the fc transport:
fc_get_event_number() - to get a FC event #
fc_host_post_event() - to send a simple FC event (32 bits of data)
fc_host_post_vendor_event() - to send a Vendor unique event, with
arbitrary amounts of data.
Note: the separation of event number allows for a LLD to send a standard
event, followed by vendor-specific data for the event.
Note: This patch assumes 2 prior fc transport patches have been installed:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115555807316329&w=2http://marc.theaimsgroup.com/?l=linux-scsi&m=115581614930261&w=2
Sorry - next time I'll do something like making these individual
patches of the same posting when I know they'll be posted closely
together.
Signed-off-by: James Smart <James.Smart@emulex.com>
Tidy up configuration not to make SCSI always select NET
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add Promise SuperTrak 'stex' driver, supporting SuperTrak
EX8350/8300/16350/16300 controllers. The controller's firmware accepts
SCSI commands, handing them to the underlying RAID or JBOD disks.
The driver consisted of the following cleanups and fixes, beyond its
initial submission:
Ed Lin:
stex: cleanup and minor fixes
stex: add new device ids
stex: update internal copy code path
stex: add hard reset function
stex: adjust command timeout in slave_config routine
stex: use more efficient method for unload/shutdown flush
Jeff Garzik:
[SCSI] Add Promise SuperTrak 'shasta' driver.
Rename drivers/scsi/shasta.c to stex.c ("SuperTrak EX").
[SCSI] stex: update with community comments from 'Promise SuperTrak' thread
[SCSI] stex: Fix warning, trim trailing whitespace.
[SCSI] stex: remove last remnants of "shasta" project code name
[SCSI] stex: removed 6-byte command emulation
[SCSI] stex: minor cleanups
[SCSI] stex: minor fixes: irq flag, error return value
[SCSI] stex: use dma_alloc_coherent()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
arcmsr is a driver for the Areca Raid controller, a host based RAID
subsystem that speaks SCSI at the firmware level.
This patch is quite a clean up over the initial submission with
contributions from:
Randy Dunlap <rdunlap@xenotime.net>
Christoph Hellwig <hch@lst.de>
Matthew Wilcox <matthew@wil.cx>
Adrian Bunk <bunk@stusta.de>
Signed-off-by: Erich Chen <erich@areca.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: iSER Kconfig and Makefile
IB/iser: iSER handling of memory for RDMA
IB/iser: iSER RDMA CM (CMA) and IB verbs interaction
IB/iser: iSER initiator iSCSI PDU and TX/RX
IB/iser: iSCSI iSER transport provider high level code
IB/iser: iSCSI iSER transport provider header file
IB/uverbs: Remove unnecessary list_del()s
IB/uverbs: Don't free wr list when it's known to be empty
HighPoint RocketRAID 3220/3320 series 8 channel PCI-X SATA RAID Host
Adapters.
Fixes from original submission:
Merge Andrew Morton's patches:
- Provide locking for global list
- Fix debug printks
- uninline function with multiple callsites
- coding style fixups
- remove unneeded casts of void*
- kfree(NULL) is legal
- Don't "succeed" if register_chrdev() failed - otherwise we'll later
unregister a not-registered chrdev.
- Don't return from hptiop_do_ioctl() with the spinlock held.
- uninline __hpt_do_ioctl()
Update for Arjan van de Ven's comments:
- put all asm/ includes after the linux/ ones
- replace mdelay with msleep
- add pci posting flush
- do not set pci command reqister in map_pci_bar
- do not try merging sg elements in hptiop_buildsgl()
- remove unused outstandingcommands member from hba structure
- remove unimplemented hptiop_abort() handler
- remove typedef u32 hpt_id_t
Other updates:
- fix endianess
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
include/scsi/scsi_devinfo.h
Same number for two BLIST flags: BLIST_MAX_512 and BLIST_ATTACH_PQ3
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a lot of code duplcited between iscsi_tcp
and the upcoming iscsi_iser driver. This patch puts
the duplicated code in a lib. There is more code
to move around but this takes care of the
basics. For iscsi_offload if they use the lib we will
probably move some things around. For example in the
queuecommand we will not assume that the LLD wants
to do queue_work, but it is better to handle that
later when we know for sure what iscsi_offload looks
like (we could probably do this for iscsi_iser though to).
Ideally I would like to get the iscsi_transports modules
to a place where all they really have to do is put data
on the wire, but how to do that will hopefully be more clear
when we see other modules like iscsi_offload. Or maybe
iscsi_offload will not use the lib and it will just be
iscsi_iser and iscsi_tcp and maybe the iscsi_tcp_tgt if that
is allowed in mainline.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A lot of EH codes are about to be added to libata. Separate out
libata-eh.c. ata_scsi_timed_out(), ata_scsi_error(),
ata_qc_timeout(), ata_eng_timeout(), ata_eh_qc_complete() and
ata_eh_qc_retry() are moved. No code is changed by this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the debug driver is built-in, link it in last, so that any real
drivers will probe first, rather than having the debug driver pick the
first scsi slots..
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original From: Adrian Bunk
Here's a composite patch with Adrian's original additions and
help-text with the new Kconfig variable SCSI_QLA_FC.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
oktagon_esp is described as modular. However, drivers/scsi/Makefile doesn't
handle it right - it's multi-object module, with one of the parts being built
from .S. Current makefile tries to declare each part a module of its own;
that not only wouldn't work (oktagon_io.o doesn't have the right parts for
that), it actually doesn't even build since kbuild doesn't believe in
single-object modules built from .S. Turned into proper multi-object
module...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SCSI qlogicisp driver is both marked BROKEN and superseded by the
qla1280 driver.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hopefully there should be a brand new replacement driver for this heap
of junk by the beginning of next year.
Acked By: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SAS transport class contains common code to deal with SAS HBAs, an
aproximated representation of SAS topologies in the driver model,
and various sysfs attributes to expose these topologies and managment
interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces
two additional intermediate objects: The SAS PHY as represented by struct
sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS
remote PHY represented by struct sas_rphy defines an "incoming" PHY on a
SAS Expander or end device. Note that this is purely a software concept, the
underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs
form a wide port based on the port_identifier attribute, which is the same
for all PHYs in a port.
This submission doesn't handle hot-plug addition or removal of SAS devices
and thus doesn't do scanning in a workqueue yet, that will be added in
phase2 after this submission. In a third phase I will add additional
managment infrastructure.
I think this submission is ready for 2.6.14, but additional comments are
of course very welcome.
I'd like to thanks James Smart a lot for his very useful input on the
design.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is my libata compatible low level driver for the Marvell SATA
family. Currently it successfully runs in PIO mode on a 6081 chip.
EDMA support is in the works and should be done shortly. Review,
testing (especially on other flavors of Marvell), comments welcome.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The idea behind a RAID class is to provide a uniform interface to all
RAID subsystems (both hardware and software) in the kernel.
To do that, I've made this class a transport class that's entirely
subsystem independent (although the matching routines have to match per
subsystem, as you'll see looking at the code). I put it in the scsi
subdirectory purely because I needed somewhere to play with it, but it's
not a scsi specific module.
I used a fusion raid card as the test bed for this; with that kind of
card, this is the type of class output you get:
jejb@titanic> ls -l /sys/class/raid_devices/20\:0\:0\:0/
total 0
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-0 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:0/20:1:0:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-1 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:1/20:1:1:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 device -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:0:0/20:0:0:0/
-r--r--r-- 1 root root 16384 Aug 16 17:21 level
-r--r--r-- 1 root root 16384 Aug 16 17:21 resync
-r--r--r-- 1 root root 16384 Aug 16 17:21 state
So it's really simple: for a SCSI device representing a hardware raid,
it shows the raid level, the array state, the resync % complete (if the
state is resyncing) and the underlying components of the RAID (these are
exposed in fusion on the virtual channel 1).
As you can see, this type of information can be exported by almost
anything, including software raid.
The more difficult trick, of course, is going to be getting it to
perform configuration type actions with writable attributes.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
