ap/station interface limit has been changed to allow
creating maximum 3 interfaces.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The total delay of HDMI hotplug detecting with 30ms is sometimes not
enoughtfor HDMI live status up with specific HDMI monitors in BSW platform.
After doing experiments for following monitors, it needs 80ms at least
for those worst cases.
Lenovo L246 1xwA (4 failed, necessary hot-plug delay: 58/40/60/40ms)
Philips HH2AP (9 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms)
BENQ ET-0035-N (6 failed, necessary hot-plug delay: 60/50/50/80/80/40ms)
DELL U2713HM (2 failed, necessary hot-plug delay: 58/59ms)
HP HP-LP2475w (5 failed, necessary hot-plug delay: 70/50/40/60/40ms)
It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Gary Wang <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.com
Tested-by: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit f8d03ea005)
[Jani: undo the file mode change of the original commit]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When I had rewritten the code for ixgbe_clear_vf_vlans() it looks like I
had transitioned back and forth between using word as an offset and using
word as a register offset. As a result I honestly don't see how the code
was working before other than the fact that resetting the VLANs on the VF
like didn't do much to clear them.
Another issue found is that the mask was using a divide instead of a
modulus. As a result the mask bit was incorrectly being set to either bit
0 or 1 based on the value of the VF being tested. As a result the wrong
VFs were having their VLANs cleared if they were enabled.
I have updated the code so that word represents the offset in the array.
This way we can use the modulus and xor operations and they will make sense
instead of being performed on a 4 byte aligned value.
I replaced the statement "(word % 2) ^ 1" with "~word % 2" in order to
reduce the line length as the line exceeded 80 characters with the register
name inserted. The two should be equivalent so the change should be safe.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x revision check needs to check a value, not just a bit.
Use a mask and check the value. Also remove the redundant check
inside the ixgbe_enter_lplu_t_x550em, because it can only be called
when both the mac type and revision check pass.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 allows for up to 64 RSS queues, but the driver can have max
of 63 (-1 MSIX vector for link).
On systems with >= 64 CPUs the driver will set the redirection table
for all 64 queues which will result in packets being dropped.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the
backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missing QSFP PHY types to allow for more accurate reporting of
port settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
adapter->rx_itr_setting is not a mask so check it with == instead of &
do not default to 12K interrupts in ixgbevf_set_itr()
There should be no functional effect from these changes.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the same patch as for ixgbe but applied differently according to
busy polling. See commit 5d6002b7b8 ("ixgbe: Fix handling of NAPI
budget when multiple queues are enabled per vector")
Signed-off-by: William Dauchy <william@gandi.net>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Merge misc fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/vmstat: fix overflow in mod_zone_page_state()
ocfs2/dlm: clear migration_pending when migration target goes down
mm/memory_hotplug.c: check for missing sections in test_pages_in_a_zone()
ocfs2: fix flock panic issue
m32r: add io*_rep helpers
m32r: fix build failure
arch/x86/xen/suspend.c: include xen/xen.h
mm: memcontrol: fix possible memcg leak due to interrupted reclaim
ocfs2: fix BUG when calculate new backup super
Pull vfs fix from Al Viro:
"Fix for 3.15 breakage of fcntl64() in arm OABI compat. -stable
fodder"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[PATCH] arm: fix handling of F_OFD_... in oabi_fcntl64()
mod_zone_page_state() takes a "delta" integer argument. delta contains
the number of pages that should be added or subtracted from a struct
zone's vm_stat field.
If a zone is larger than 8TB this will cause overflows. E.g. for a
zone with a size slightly larger than 8TB the line
mod_zone_page_state(zone, NR_ALLOC_BATCH, zone->managed_pages);
in mm/page_alloc.c:free_area_init_core() will result in a negative
result for the NR_ALLOC_BATCH entry within the zone's vm_stat, since 8TB
contain 0x8xxxxxxx pages which will be sign extended to a negative
value.
Fix this by changing the delta argument to long type.
This could fix an early boot problem seen on s390, where we have a 9TB
system with only one node. ZONE_DMA contains 2GB and ZONE_NORMAL the
rest. The system is trying to allocate a GFP_DMA page but ZONE_DMA is
completely empty, so it tries to reclaim pages in an endless loop.
This was seen on a heavily patched 3.10 kernel. One possible
explaination seem to be the overflows caused by mod_zone_page_state().
Unfortunately I did not have the chance to verify that this patch
actually fixes the problem, since I don't have access to the system
right now. However the overflow problem does exist anyway.
Given the description that a system with slightly less than 8TB does
work, this seems to be a candidate for the observed problem.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have found a BUG on res->migration_pending when migrating lock
resources. The situation is as follows.
dlm_mark_lockres_migration
res->migration_pending = 1;
__dlm_lockres_reserve_ast
dlm_lockres_release_ast returns with res->migration_pending remains
because other threads reserve asts
wait dlm_migration_can_proceed returns 1
>>>>>>> o2hb found that target goes down and remove target
from domain_map
dlm_migration_can_proceed returns 1
dlm_mark_lockres_migrating returns -ESHOTDOWN with
res->migration_pending still remains.
When reentering dlm_mark_lockres_migrating(), it will trigger the BUG_ON
with res->migration_pending. So clear migration_pending when target is
down.
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
test_pages_in_a_zone() does not account for the possibility of missing
sections in the given pfn range. pfn_valid_within always returns 1 when
CONFIG_HOLES_IN_ZONE is not set, allowing invalid pfns from missing
sections to pass the test, leading to a kernel oops.
Wrap an additional pfn loop with PAGES_PER_SECTION granularity to check
for missing sections before proceeding into the zone-check code.
This also prevents a crash from offlining memory devices with missing
sections. Despite this, it may be a good idea to keep the related patch
'[PATCH 3/3] drivers: memory: prohibit offlining of memory blocks with
missing sections' because missing sections in a memory block may lead to
other problems not covered by the scope of this fix.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Alex Thorlton <athorlton@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m32r allmodconfig was failing with the error:
error: implicit declaration of function 'read'
On checking io.h it turned out that 'read' is not defined but 'readb' is
defined and 'ioread8' will then obviously mean 'readb'.
At the same time some of the helper functions ioreadN_rep() and
iowriteN_rep() were missing which also led to the build failure.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m32r allmodconfig is failing with:
In file included from ../include/linux/kvm_para.h:4:0,
from ../kernel/watchdog.c:26:
../include/uapi/linux/kvm_para.h:30:26: fatal error: asm/kvm_para.h: No such file or directory
kvm_para.h was not included in the build.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the build warning:
arch/x86/xen/suspend.c: In function 'xen_arch_pre_suspend':
arch/x86/xen/suspend.c:70:9: error: implicit declaration of function 'xen_pv_domain' [-Werror=implicit-function-declaration]
if (xen_pv_domain())
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory cgroup reclaim can be interrupted with mem_cgroup_iter_break()
once enough pages have been reclaimed, in which case, in contrast to a
full round-trip over a cgroup sub-tree, the current position stored in
mem_cgroup_reclaim_iter of the target cgroup does not get invalidated
and so is left holding the reference to the last scanned cgroup. If the
target cgroup does not get scanned again (we might have just reclaimed
the last page or all processes might exit and free their memory
voluntary), we will leak it, because there is nobody to put the
reference held by the iterator.
The problem is easy to reproduce by running the following command
sequence in a loop:
mkdir /sys/fs/cgroup/memory/test
echo 100M > /sys/fs/cgroup/memory/test/memory.limit_in_bytes
echo $$ > /sys/fs/cgroup/memory/test/cgroup.procs
memhog 150M
echo $$ > /sys/fs/cgroup/memory/cgroup.procs
rmdir test
The cgroups generated by it will never get freed.
This patch fixes this issue by making mem_cgroup_iter avoid taking
reference to the current position. In order not to hit use-after-free
bug while running reclaim in parallel with cgroup deletion, we make use
of ->css_released cgroup callback to clear references to the dying
cgroup in all reclaim iterators that might refer to it. This callback
is called right before scheduling rcu work which will free css, so if we
access iter->position from rcu read section, we might be sure it won't
go away under us.
[hannes@cmpxchg.org: clean up css ref handling]
Fixes: 5ac8fb31ad ("mm: memcontrol: convert reclaim iterator to simple css refcounting")
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [3.19+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When resizing, it firstly extends the last gd. Once it should backup
super in the gd, it calculates new backup super and update the
corresponding value.
But it currently doesn't consider the situation that the backup super is
already done. And in this case, it still sets the bit in gd bitmap and
then decrease from bg_free_bits_count, which leads to a corrupted gd and
trigger the BUG in ocfs2_block_group_set_bits:
BUG_ON(le16_to_cpu(bg->bg_free_bits_count) < num_bits);
So check whether the backup super is done and then do the updates.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Jiufei Xue <xuejiufei@huawei.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2a037f310b ("MIPS: VDSO: Fix build error") tries to fix a build
error seen with binutils 2.24 and earlier. However, the fix does not work,
and again results in the already known build errors if the kernel is built
with an earlier version of binutils.
CC arch/mips/vdso/gettimeofday.o
/tmp/ccnOVbHT.s: Assembler messages:
/tmp/ccnOVbHT.s:50: Error: can't resolve `_start' {*UND* section} - `L0 {.text section}
/tmp/ccnOVbHT.s:374: Error: can't resolve `_start' {*UND* section} - `L0 {.text section}
scripts/Makefile.build:258: recipe for target 'arch/mips/vdso/gettimeofday.o' failed
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
Fixes: 2a037f310b ("MIPS: VDSO: Fix build error")
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11926/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the return value of platform_get_irq on failure.
A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b48bb8506c5 ("openvswitch: Fix helper reference leak") fixed a
reference leak on helper objects, but inadvertently introduced a leak on
the ct template.
Previously, ct_info.ct->general.use was initialized to 0 by
nf_ct_tmpl_alloc() and only incremented when ovs_ct_copy_action()
returned successful. If an error occurred while adding the helper or
adding the action to the actions buffer, the __ovs_ct_free_action()
cleanup would use nf_ct_put() to free the entry; However, this relies on
atomic_dec_and_test(ct_info.ct->general.use). This reference must be
incremented first, or nf_ct_put() will never free it.
Fix the issue by acquiring a reference to the template immediately after
allocation.
Fixes: cae3a26275 ("openvswitch: Allow attaching helpers to ct action")
Fixes: 5b48bb8506c5 ("openvswitch: Fix helper reference leak")
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei says:
====================
bpf: hash: use per-bucket spinlock
This patchset tries to optimize ebpf hash map, and follows
the idea:
Both htab_map_update_elem() and htab_map_delete_elem()
can be called from eBPF program, and they may be in kernel
hot path, it isn't efficient to use a per-hashtable lock
in this two helpers, so this patch converts the lock into
per-bucket spinlock.
With this patchset, looks the performance penalty from eBPF
decreased a lot, see the following test:
1) run 'tools/biolatency' of bcc before running block test;
2) run fio to test block throught over /dev/nullb0,
(randread, 16jobs, libaio, 4k bs) and the test box
is one 24cores(dual sockets) VM server:
- without patchset: 607K IOPS
- with this patchset: 1184K IOPS
- without running eBPF prog: 1492K IOPS
TODO:
- remove the per-hashtable atomic counter
V2:
- fix checking on buckets size
V1:
- fix the wrong 3/3 patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both htab_map_update_elem() and htab_map_delete_elem() can be
called from eBPF program, and they may be in kernel hot path,
so it isn't efficient to use a per-hashtable lock in this two
helpers.
The per-hashtable spinlock is used for protecting bucket's
hlist, and per-bucket lock is just enough. This patch converts
the per-hashtable lock into per-bucket spinlock, so that
contention can be decreased a lot.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock is just used for protecting the per-bucket
hlist, so it isn't needed for selecting bucket.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparing for removing global per-hashtable lock, so
the counter need to be defined as aotmic_t first.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've moved the check for "number_destination_params" forward
a few lines to avoid leaking "cmd".
Fixes: caa575a86e ('NFC: nci: fix possible crash in nci_core_conn_create')
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
gpio irq is already configured by the core i2c layers
when reaching the probe function
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
gpio irq is already configured by the core i2c layers
when reaching the probe function.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
microread platform_data header had an NXP header.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In microread_i2c_phy, irq field is never used.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is cleaner to check if the i2c_client irq is not configured
properly before allocating any data.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for missing HCI event EVT_CONNECTIVITY and forward
it to userspace.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The core st21nca module is useless without the I2C access module.
So hide NFC_ST21NFCA and select it automatically if either
NFC_ST21NFCA_I2C is selected.
This avoids presenting NFC_ST21NFCA when NFC_ST21NFCA_I2C can't be
selected.
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The core st-nci module is useless without either the I2C or the
SPI access module. So hide NFC_ST_NCI and select it automatically
if either NFC_ST_NCI_I2C or NFC_ST_NCI_SPI is selected.
This avoids presenting NFC_ST_NCI when neither NFC_ST_NCI_I2C nor
NFC_ST_NCI_SPI can be selected.
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
net/nfc/nci/hci.c: In function nci_hci_connect_gate :
net/nfc/nci/hci.c:679: warning: comparison is always false due to limited range of data type
In case of error, nci_hci_create_pipe() returns NCI_HCI_INVALID_PIPE,
and not a negative error code.
Correct the check to fix this.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for acpi probing.
SMO2101 is used for st21nfcb
SMO2102 is used for st21nfcc
It has been tested with the following acpi node on Minnowboard:
Note: Remove uicc-present or ese-present Package if one them is not
supported.
Device (NFC1)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "SMO2101") // _HID: Hardware ID
Name (_CID, "SMO2101") // _CID: Compatible ID
Name (_DDN, "SMO NFC") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Name (_DSD, Package (0x02)
{
/* Device Properties for _DSD */
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package (0x02)
{
Package (0x02) { "uicc-present", 1 },
Package (0x02) { "ese-present", 1 }
}
})
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
I2cSerialBus (0x0008, ControllerInitiated, 400000,
AddressingMode7Bit, "\\_SB.I2C7",
0x00, ResourceConsumer, ,)
GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0001
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0002,
}
})
Return (SBUF) /* \_SB_.I2C7.NFC1._CRS.SBUF */
}
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add macro definition for each gpio string for an easier code
maintenance.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
