The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip. Otherwise the driver won't find the device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards. I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig. There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pattern substitution rules were failing when used with zImage-dtb
targets. If zImage-dtb.initrd was selected, the pattern substitution
would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which
caused the build to fail.
This renames zImage-dtb to dtbImage to avoid the problem entirely.
By not using the zImage prefix then is no potential for namespace
collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch allows interrupts to occur on the
sbc8548. Currently PCI and PCI-X devices get assigned an IRQ
but the interrupt count never increases. This solves the
problem and adds PCI support as well.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes the following bug:
http://ozlabs.org/pipermail/linuxppc-dev/2008-February/051979.html
Separate defconfigs are no longer needed now that CONFIG_DEVICE_TREE is gone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct the remaining 44x cuboot wrappers to define TARGET_4xx as well. This
creates the correct structure to use, including things like the second MAC
address.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
In order to get the proper boad info (bd_info) structure defined in ppcboot.h
both TARGET_4xx and TARGET_44x should be defined for all PowerPC 440 boards.
The 440GX boards also need TARGET_440GX defined since they have 4 EMACs and
there are 4 MAC addesses in bd_info passed by u-boot.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch changes the katmai (440SPe) L1 cache size to 32k. Some
whitespace issues are cleaned up too.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since the 4xx PCIe driver checks for 405ex compatibility, the
PCIe interface was not detected as it is currently defined as
"405exr" compatible. This patch changes it to "405ex".
The 405EX and 405EXr are identical exept that the 2nd PCIe and the
2nd EMAC interfaces are missing.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
GCC versions before 3.4 did not support the -mcpu=440 option. Use
-mcpu=405 for the 4xx specific bootwrapper files, as that has been
around for much longer.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove all "i2c" and "xxmii-interface" (rgmii etc) device_type entries
from the 4xx dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Fix a bug in the lv1_get_repository_node_value() routine of the PS3
bootwrapper. Changes in the PS3 system firmware 2.20 cause this bug
to hang the system when branching from the bootwrapper to the kernel
_start.
Since the video system has not yet been enabled at the time
the bug is hit, the system hangs with a blank screen. Earlier
firmwares don't cause such a catastrophic failure, and so this
bug went undetected.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the kernel uses CONFIG_DEVICE_TREE to wrap a kernel image
with a fdt blob which means for any given configuration only one dts
file can be selected and so support for only one board can be built
This moves the selection of the default .dts file out of the kernel
config and into the bootwrapper makefile. The makefile chooses which
images to build based on the kernel config and the dts source file
name is taken directly from the image name. For example "cuImage.ebony"
will use "ebony.dts" as the device tree source file.
In addition, this patch allows a specific image to be requested from the
command line by adding "cuImage.%" and "treeImage.%" targets to the list
of valid built targets in arch/powerpc/Makefile. This allows the default
dts selection to be overridden.
Another advantage to this change is it allows a single defconfig to be
supplied for all boards using the same chip family and only differing in
the device tree.
Important note: This patch adds two new zImage targets; zImage.dtb.% and
zImage.dtb.initrd.% for zImages with embedded dtb files. Currently
there are 5 platforms which require this: ps3, ep405, mpc885ads, ep88xc,
adder875-redboot and ep8248e. This patch *changes the zImage filenames*
for those platforms. ie. 'zImage.ps3' is now 'zImage.dtb.ps3'.
This new zImage.dtb targets were added so that the .dts file could be
part of the dependancies list for building them.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Minimal /dts-v1/ device tree for mpc5121 ads.
port-number property in uart nodes
will go away after the driver learns to use aliases
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cleaned up IRQ layout and removed unsused ISU allocations.
Fixed RTC address typo from /dts-v1/ conversion.
Incorporated list suggestions to use an "iomega," vendor prefix,
and to use a node reference rather than a hard path.
Signed-off-by: Jon Loeliger <jdl@@jdl.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
cpm_uart_core has a dependency on fsl,cpm-brg/clock-frequency, this
means that a .dts that uses the cpm uart driver needs to supply a
clock-frequency entry for get_brgfreq to return a meaningful number.
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8313 rdb has a ds1339 at address 0x68.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to the 8349EA ref man, the second PCI PHB IRQ is 67. Thanks to Peter
Van Ackeren for finding this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SCCR USB bits are in a different location on the mpc8315.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch converts the remaining 83xx boards to the dts-v1 format.
This includes the mpc8313_rdb, mpc832x_mds, mpc8323_rdb, mpc8349emitx,
mpc8349emitxgp and the mpc836x_mds.
The mpc8315_rdb mpc834x_mds, mpc837[789]_*, and sbc8349 were already
dts-v1 and only undergo minor changes for the sake of formatting
consistency across the whole group of boards; i.e. the idea being
that you can do a "diff -u board_A.dts board_B.dts" and see something
meaningful.
The general rule I've applied is that entries for values normally
parsed by humans are left in decimal (i.e. IRQ, cache size, clock
rates, basic counts and indexes) and all other data (i.e. reg and
ranges, IRQ flags etc.) remain in hex.
I've used dtc to confirm that the output prior to this changeset
matches the output after this changeset is applied for all boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently there are several dts that don't specify address or size
cells for the muram. This causes dtc to use default values, one of
which is an address-cells of two, and this breaks the parsing of the
muram ranges, which is assuming an address-cells of one. For example:
Warning (reg_format): "reg" property in
/qe@e0100000/muram@10000/data-only@0 has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 1)
Explicitly setting the address and size cells gets it parsed properly
and gets rid of the four dtc warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the dts files for the MPC838xE Reference Development Board (RDB).
The board is a mini-ITX reference board with 256M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.
the difference among the three files is the 8377 has two, the 8378
none, and the 8379 has four sata controllers.
partially based on the 8379 mds device trees.
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the dts for the MPC8315E Reference Development Board (RDB).
The board is a mini-ITX reference board with 128M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
it for legacy device_type probing and new "compatible" probing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
device_type property is bogus, thus use proper compatible.
Also change compatible property to "fsl,ucc-mdio".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* "simple-bus" covers all our needs for of_platform_bus_probe()
* make device tree name just 'soc' not 'soc85..'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move mpc834x_mds device tree source forward to dts-v1 format. Nothing
too complex in this one, so it boils down to just adding a bunch of 0x
in the right places and converting clock speeds to decimal.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the device tree source for the Wind River SBC834x board.
It is based on the MPC834x_MDS DTS, with the biggest difference being
the lack of BCSR and the PCI2 that the MDS gets via the PIB. That,
and this file is also dts-v1 format.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a v1 device tree source for the Wind River SBC8548 board.
The biggest difference between this and the MPC8548CDS reference
platform is the absence of the CDS's Arcadia peripherals and physical
access to the PCI#2 bus.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a v1 device tree source for the Wind River SBC8560 board. The
biggest difference between this and the MPC8560ADS reference platform
dts is the use of an external 16550 compatible UART instead of the CPM2.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to find a device node by just what its compatible with.
This is useful in cases that we don't have a prop to find the node with.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The various 5200 dts files don't have values specified for the soc
node, which in turn results in a warning from the processing of
every child node (roughly 40 warnings per file). This explicitly
sets the default values and gets rid of all the warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
