Some minor refactoring in the generic code was necessary for
this:
1) This controller requires 8-byte access to the interrupt map
and clear register. They are 64-bits on all the other
SBUS and PCI controllers anyways, so this was easy to cure.
2) The IMAP register has a different layout and some bits that we
need to preserve, so use a read/modify/write when making
changes to the IMAP register in generic code.
3) Flushing the entire IOMMU TLB is best done with a single write
to a register on this PCI controller, add a iommu->iommu_flushinv
for this.
Still lacks MSI support, that will come later.
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some fixups for the R7785RP board. Gets iVDR working.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds more full-featured support for the SH7722 Solution Engine.
Previously this was using the generic board, and lacked most of the
peripheral support.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the addition of the R7780MP and R7785RP, the R7780RP build
ended up breaking. Trivial compile fix.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was done in cpuinfo, but with the number of clocks
growing, it makes more sense to place this in a different proc entry.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up SH7705 CPU support and the SE7705 board
for some of the recent changes.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7722 (MobileR) to the clock framework.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This wasn't being set before, so now it's set for when it makes sense.
The shwdt case still requires HZ to be fixed at 1000 for the WOVF period,
so this is still preserved.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7780-based Solution Engine reference board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks some of the node 0 bootmem initialization in
preparation for discontigmem and sparsemem support.
ARCH_POPULATES_NODE_MAP is switched to as a result of this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the L-BOX RE2 router.
http://www.nttcom.co.jp/l-box/
L-BOX RE2 is a SH7751R-based router. It has CF, Cardbus, serial,
and LAN x2. This is one of the very few SH boards that a general
person can obtain now.
The L-BOX shipped with a 2.4.28 kernel, this is a rewritten patch
adding it to current git.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Each board sets the total number of IRQs that it's interested in via
the machvec. Previously we cared about the off vs on-chip IRQ range,
but any code relying on that is long dead. Set NR_IRQS to something
sensible given the vector range, and allow boards to cap it if they
really care.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wire up GENERIC_BUG for SH. This moves off of the special bug
frame and on to the generic struct bug_entry. Roughly the same
semantics are retained, and we can kill off some of the verbose
BUG() reporting code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Change NLM internal interface to pass more information for test lock; we
need this to make sure the cookie information is pushed down to the place
where we do request deferral, which is handled for testlock by the
following patch.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
We need to keep some state for a pending asynchronous lock request, so this
patch adds that state to struct nlm_block.
This also adds a function which defers the request, by calling
rqstp->rq_chandle.defer and storing the resulting deferred request in a
nlm_block structure which we insert into lockd's global block list. That
new function isn't called yet, so it's dead code until a later patch.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Acquiring a lock on a cluster filesystem may require communication with
remote hosts, and to avoid blocking lockd or nfsd threads during such
communication, we allow the results to be returned asynchronously.
When a ->lock() call needs to block, the file system will return
-EINPROGRESS, and then later return the results with a call to the
routine in the fl_grant field of the lock_manager_operations struct.
This differs from the case when ->lock returns -EAGAIN to a blocking
lock request; in that case, the filesystem calls fl_notify when the lock
is granted, and the caller retries the original lock. So while
fl_notify is merely a hint to the caller that it should retry, fl_grant
actually communicates the final result of the lock operation (with the
lock already acquired in the succesful case).
Therefore fl_grant takes a lock, a status and, for the test lock case, a
conflicting lock. We also allow fl_grant to return an error to the
filesystem, to handle the case where the fl_grant requests arrives after
the lock manager has already given up waiting for it.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Lock managers need to be able to cancel pending lock requests. In the case
where the exported filesystem manages its own locks, it's not sufficient just
to call posix_unblock_lock(); we need to let the filesystem know what's
happening too.
We do this by adding a new fcntl lock command: FL_CANCELLK. Some day this
might also be made available to userspace applications that could benefit from
an asynchronous locking api.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
The nfsv4 protocol's lock operation, in the case of a conflict, returns
information about the conflicting lock.
It's unclear how clients can use this, so for now we're not going so far as to
add a filesystem method that can return a conflicting lock, but we may as well
return something in the local case when it's easy to.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Factor out the code that switches between generic and filesystem-specific lock
methods; eventually we want to call this from lock managers (lockd and nfsd)
too; currently they only call the generic methods.
This patch does that for all the setlk code.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Factor out the code that switches between generic and filesystem-specific lock
methods; eventually we want to call this from lock managers (lockd and nfsd)
too; currently they only call the generic methods.
This patch does that for test_lock.
Note that this hasn't been necessary until recently, because the few
filesystems that define ->lock() (nfs, cifs...) aren't exportable via NFS.
However GFS (and, in the future, other cluster filesystems) need to implement
their own locking to get cluster-coherent locking, and also want to be able to
export locking to NFS (lockd and NFSv4).
So we accomplish this by factoring out code such as this and exporting it for
the use of lockd and nfsd.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
posix_test_lock() and ->lock() do the same job but have gratuitously
different interfaces. Modify posix_test_lock() so the two agree,
simplifying some code in the process.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (66 commits)
KVM: Remove unused 'instruction_length'
KVM: Don't require explicit indication of completion of mmio or pio
KVM: Remove extraneous guest entry on mmio read
KVM: SVM: Only save/restore MSRs when needed
KVM: fix an if() condition
KVM: VMX: Add lazy FPU support for VT
KVM: VMX: Properly shadow the CR0 register in the vcpu struct
KVM: Don't complain about cpu erratum AA15
KVM: Lazy FPU support for SVM
KVM: Allow passing 64-bit values to the emulated read/write API
KVM: Per-vcpu statistics
KVM: VMX: Avoid unnecessary vcpu_load()/vcpu_put() cycles
KVM: MMU: Avoid heavy ASSERT at non debug mode.
KVM: VMX: Only save/restore MSR_K6_STAR if necessary
KVM: Fold drivers/kvm/kvm_vmx.h into drivers/kvm/vmx.c
KVM: VMX: Don't switch 64-bit msrs for 32-bit guests
KVM: VMX: Reduce unnecessary saving of host msrs
KVM: Handle guest page faults when emulating mmio
KVM: SVM: Report hardware exit reason to userspace instead of dmesg
KVM: Retry sleeping allocation if atomic allocation fails
...
utrace removes the ptrace_message field in task_struct. Move our use
of this field into a new member in thread_info called "syscall"
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC fs/nfs/nfsroot.o
fs/nfs/nfsroot.c:131: error: tokens causes a section type conflict
make[2]: *** [fs/nfs/nfsroot.o] Error 1
This is due to mixing const and non-const content in the same section
which halfway recent gccs absolutely hate. Fixed by dropping the const.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/voyager-2.6:
[VOYAGER] add smp alternatives
[VOYAGER] Use modern techniques to setup and teardown low identiy mappings.
[VOYAGER] Convert the monitor thread to use the kthread API
[VOYAGER] clockevents driver: bring voyager in to line
[VOYAGER] clockevents: correct boot cpu is zero assumption
[VOYAGER] add smp_call_function_single
The S3C2410_UDC_SETIX() macro is not used and won't be used by the udc
driver, so delete it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
__ioremap() took a set of page table flags (specifically the cacheable
and bufferable bits) to control the mapping type. However, with
the advent of ARMv6, this is far too limited.
Replace the page table flags with a memory type index, so that the
desired attributes can be selected from the mem_type table.
Finally, to prevent silent miscompilation due to the differing
arguments, rename the __ioremap() and __ioremap_pfn() functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add cached device type for ioremap_cached(). Group all device memory
types together, and ensure that they all have a "MT_DEVICE" prefix.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add generic IEEE 802.11 definitions.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People treating the *_pid fields in netlink as a process ID has caused
endless confusion over the years. The fact that our own netlink.h
does this only adds to the confusion.
So here is a patch to change the comments to refer to it as the port
ID which hopefully will make it clear what the purpose of the fields
really is.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/serial/8250.c:1837: warning: suggest parentheses around arithmetic in operand of |
due to a macro argument being used without required parenthesis.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the D-Link DSM-G600 Rev A.
This is an ARM XScale IXP4xx system relatively similar to
the NSLU2 and NAS-100D already supported by mainline. An
important difference is Gigabit Ethernet support using
the Via Velocity chipset.
This patch is the combined work of Michael Westerhof and
Alessandro Zummo, with contributions from Michael-Luke
Jones. This version addresses review comments from rmk
and Deepak Saxena.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Michael Westerhof <mwester@dls.net>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (46 commits)
mmc-omap: Clean up omap set_ios and make MMC_POWER_ON work
mmc-omap: Fix omap to use MMC_POWER_ON
mmc-omap: add missing '\n'
mmc: make tifm_sd_set_dma_data() static
mmc: remove old card states
mmc: support unsafe resume of cards
mmc: separate out reading EXT_CSD
mmc: break apart switch function
MMC: Fix handling of low-voltage cards
MMC: Consolidate voltage definitions
mmc: add bus handler
wbsd: check for data opcode earlier
mmc: Separate out protocol ops
mmc: Move core functions to subdir
mmc: deprecate mmc bus topology
mmc: remove card upon suspend
mmc: allow suspended block driver to be removed
mmc: Flush pending detects on host removal
mmc: Move host and card drivers to subdirs
mmc: Move queue functions to mmc_block
...
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (28 commits)
NFS: Fix a compile glitch on 64-bit systems
NFS: Clean up nfs_create_request comments
spkm3: initialize hash
spkm3: remove bad kfree, unnecessary export
spkm3: fix spkm3's use of hmac
NFS4: invalidate cached acl on setacl
NFS: Fix directory caching problem - with test case and patch.
NFS: Set meaningful value for fattr->time_start in readdirplus results.
NFS: Added support to turn off the NFSv3 READDIRPLUS RPC.
SUNRPC: RPC client should retry with different versions of rpcbind
SUNRPC: remove old portmapper
NFS: switch NFSROOT to use new rpcbind client
SUNRPC: switch the RPC server to use the new rpcbind registration API
SUNRPC: switch socket-based RPC transports to use rpcbind
SUNRPC: introduce rpcbind: replacement for in-kernel portmapper
SUNRPC: Eliminate side effects from rpc_malloc
SUNRPC: RPC buffer size estimates are too large
NLM: Shrink the maximum request size of NLM4 requests
NFS: Use pgoff_t in structures and functions that pass page cache offsets
NFS: Clean up nfs_sync_mapping_wait()
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits)
[SCTP]: Set assoc_id correctly during INIT collision.
[SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv()
[SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP.
[SCTP]: Verify all destination ports in sctp_connectx.
[XFRM] SPD info TLV aggregation
[XFRM] SAD info TLV aggregationx
[AF_RXRPC]: Sort out MTU handling.
[AF_IUCV/IUCV] : Add missing section annotations
[AF_IUCV]: Implementation of a skb backlog queue
[NETLINK]: Remove bogus BUG_ON
[IPV6]: Some cleanups in include/net/ipv6.h
[TCP]: zero out rx_opt in tcp_disconnect()
[BNX2]: Fix TSO problem with small MSS.
[NET]: Rework dev_base via list_head (v3)
[TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start
[BNX2]: Update version and reldate.
[BNX2]: Print bus information for PCIE devices.
[BNX2]: Add 1-shot MSI handler for 5709.
[BNX2]: Restructure PHY event handling.
[BNX2]: Add indirect spinlock.
...
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits)
Input: gpio_keys - add support for switches (EV_SW)
Input: cobalt_btns - convert to use polldev library
Input: add skeleton for simple polled devices
Input: update some documentation
Input: wistron - fix typo in keymap for Acer TM610
Input: add input_set_capability() helper
Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs
Input: i8042 - add Panasonic CF-29 to nomux list
Input: lifebook - split into 2 devices
Input: lifebook - add signature of Panasonic CF-29
Input: lifebook - activate 6-byte protocol on select models
Input: lifebook - work properly on Panasonic CF-18
Input: cobalt buttons - separate device and driver registration
Input: ati_remote - make button repeat sensitivity configurable
Input: pxa27x - do not use deprecated SA_INTERRUPT flag
Input: ucb1400 - make delays configurable
Input: misc devices - switch to using input_dev->dev.parent
Input: joysticks - switch to using input_dev->dev.parent
Input: touchscreens - switch to using input_dev->dev.parent
Input: mice - switch to using input_dev->dev.parent
...
Fixed up conflicts with core device model removal of "struct subsystem" manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
remove "struct subsystem" as it is no longer needed
sysfs: printk format warning
DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
platform: reorder platform_device_del
Driver core: fix show_uevent from taking up way too much stack
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
PCI: Free resource files in error path of pci_create_sysfs_dev_files()
pci-quirks: disable MSI on RS400-200 and RS480
PCI hotplug: Use menuconfig objects
PCI: ZT5550 CPCI Hotplug driver fix
PCI: rpaphp: Remove semaphores
PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
PCI: rpaphp: Document is_php_dn()
PCI: rpaphp: Document find_php_slot()
PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
PCI: rpaphp: refactor tail call to rpaphp_register_slot()
PCI: rpaphp: remove rpaphp_set_attention_status()
PCI: rpaphp: remove print_slot_pci_funcs()
PCI: rpaphp: Remove setup_pci_slot()
PCI: rpaphp: remove a call that does nothing but a pointer lookup
PCI: rpaphp: Remove another wrappered function
PCI: rpaphp: Remve another call that is a wrapper
PCI: rpaphp: remove a function that does nothing but wrap debug printks
PCI: rpaphp: Remove un-needed goto
PCI: rpaphp: Fix a memleak; slot->location string was never freed
...
ps3av:
- Move the definition of struct ps3av to ps3av.c, as it's locally used only.
- Kill ps3av.sem, use the existing ps3av.mutex instead.
- Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
Its use is protected by a semaphore anyway.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert kmap_atomic() in the non-highmem case from a macro to a static
inline function, for better type-checking and the ability to pass void
pointers instead of struct page pointers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sync the nubus defines with the latest code in the mac68k repo. Some of these
are needed for DP8390 driver update in the next patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asm-m68k/adb.h header is unused. Some definitions are wrong and the rest
are duplicated in linux/adb.h. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atari keyboard and mouse support.
(reformating and Kconfig fixes by Roman Zippel)
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the INIT/COOKIE-ACK collision cases, it's possible to get
into a situation where the association id is not yet set at the time
of the user event generation. As a result, user events have an
association id set to 0 which will confuse applications.
This happens if we hit case B of duplicate cookie processing.
In the particular example found and provided by Oscar Isaula
<Oscar.Isaula@motorola.com>, flow looks like this:
A B
---- INIT-------> (lost)
<---------INIT------
---- INIT-ACK--->
<------ Cookie ECHO
When the Cookie Echo is received, we end up trying to update the
association that was created on A as a result of the (lost) INIT,
but that association doesn't have the ID set yet.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregate the SPD info TLVs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregate the SAD info TLVs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the inital implementation we missed to implement a skb backlog
queue . The result is that socket receive processing tossed packets.
Since AF_IUCV connections are working synchronously it leads to
connection hangs. Problems with read, close and select also occured.
Using a skb backlog queue is fixing all of these problems .
Signed-off-by: Jennifer Hunt <jenhunt@us.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These helper functions are a leftover from 2.4 sync I/O and are a
notorious source for bugs. They lead to device driver specific code
creeping into cio, and some issues can't really be fixed at all.
Device drivers can easily implement those functions themselves in a
more robust manner, so let's get rid of them.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
And here's a port of the powerpc patch to get rid of the notifier
chain completely to s390. It's ontop of Martins patch as that one
is in mainline already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
1) struct ip6_flowlabel : moves 'users' field to avoid two 32bits
holes for 64bit arches. Shrinks by 8 bytes sizeof(struct
ip6_flowlabel)
2) ipv6_addr_cmp() and ipv6_addr_copy() dont need (void *) casts :
Compiler might take into account natural alignement of in6_addr
structs to emit better code for memcpy()/memcmp() Casts to (void *)
force byte accesses.
3) ipv6_addr_prefix() optimization :
Better to clear whole struct, as compiler can emit better code for
memset(addr, 0, 16) (2 stores on x86_64), and avoid some conditional
branches.
# size vmlinux.after vmlinux.before
text data bss dec hex filename
5262262 647612 557432 6467306 62aeea vmlinux.after
5262550 647612 557432 6467594 62b00a vmlinux.before
thats 288 bytes saved.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup of dev_base list use, with the aim to simplify making device
list per-namespace. In almost every occasion, use of dev_base variable
and dev->next pointer could be easily replaced by for_each_netdev
loop. A few most complicated places were converted to using
first_netdev()/next_netdev().
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI ID and code to support the 5709 Serdes PHY.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 2.5G supported and advertising bit definitions. 2.5G is supported
by the bnx2 driver.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the i.MX UART register descriptions from
include/asm-arm/arch-imx/imx-regs.h to the serial driver itself.
This helps using the driver on other architectures like mx31
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the position of the netx reset control register
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
'type' in the struct expansion_card is only used to indicate
whether this card is an EASI card or not. Therefore, having
it as an enum is wasteful (and introduces additional noise
when we come to remove the enum.) Convert it to a mere flag
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Definitions for Analog-to-Digital Converter (ADC) found on the Atmel
AT91SAM9260 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The tpmi units interface with the SAS controller on iop348.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the iop3xx platform support code assumes that RedBoot is the
bootloader and has already initialized the ATU. Linux should handle this
initialization for three reasons:
1/ The memory map that RedBoot sets up is not optimal (page_to_dma and
virt_to_phys return different addresses). The effect of this is that using
the dma mapping API for the internal bus dma units generates pci bus
addresses that are incorrect for the internal bus.
2/ Not all iop platforms use RedBoot
3/ If the ATU is already initialized it indicates that the iop is an add-in
card in another host, it does not own the PCI bus, and should not be
re-initialized.
Changelog:
* rather than change nr_controllers to zero, simply do not call
pci_common_init
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the common push/pull sequences into a few helper functions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While porting some changes of the 2.6.21-rc7 pptp/proto_gre conntrack
and nat modules to a 2.4.32 kernel I noticed that the gre_key function
returns a wrong pointer to the GRE key of a version 0 packet thus
corrupting the packet payload.
The intended behaviour for GREv0 packets is to act like
nf_conntrack_proto_generic/nf_nat_proto_unknown so I have ripped the
offending functions (not used anymore) and modified the
nf_nat_proto_gre modules to not touch version 0 (non PPTP) packets.
Signed-off-by: Jorge Boncompte <jorge@dti2.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP has a transitional state when SACK is not in use during
which this invariant is temporarily broken. Without SACK,
tcp_clean_rtx_queue does not decrement sacked_out. Therefore
calls to tcp_sync_left_out before sacked_out is again
corrected by tcp_fastretrans_alert can trigger this trap as
sacked_out still has couple of segments that are already out
of window.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __dev_getfirstbyhwtype for callers that don't want a reference but
some data from the device and thus need to take the rtnl anyway.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix skbuff.h kernel-doc:
linux-2.6.21-git4//include/linux/skbuff.h:316): No description found for parameter 'transport_header'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the match_*() functions take a const pointer to the options table
and make strings pointers in the options table const too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__HAVE_ARCH_ADDR_SET seems unused these days, just get rid of it.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is illegal not to return from a pio or mmio request without completing
it, as mmio or pio is an atomic operation. Therefore, we can simplify
the userspace interface by avoiding the completion indication.
Signed-off-by: Avi Kivity <avi@qumranet.com>
With this, we can specify that accesses to one physical memory range will
be remapped to another. This is useful for the vga window at 0xa0000 which
is used as a movable window into the (much larger) framebuffer.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The current string pio interface communicates using guest virtual addresses,
relying on userspace to translate addresses and to check permissions. This
interface cannot fully support guest smp, as the check needs to take into
account two pages at one in case an unaligned string transfer straddles a
page boundary.
Change the interface not to communicate guest addresses at all; instead use
a buffer page (mmaped by userspace) and do transfers there. The kernel
manages the virtual to physical translation and can perform the checks
atomically by taking the appropriate locks.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows us to store offsets in the kernel/user kvm_run area, and be
sure that userspace has them mapped. As offsets can be outside the
kvm_run struct, userspace has no way of knowing how much to mmap.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Allow a special signal mask to be used while executing in guest mode. This
allows signals to be used to interrupt a vcpu without requiring signal
delivery to a userspace handler, which is quite expensive. Userspace still
receives -EINTR and can get the signal via sigwait().
Signed-off-by: Avi Kivity <avi@qumranet.com>
This is redundant, as we also return -EINTR from the ioctl, but it
allows us to examine the exit_reason field on resume without seeing
old data.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently, userspace is told about the nature of the last exit from the
guest using two fields, exit_type and exit_reason, where exit_type has
just two enumerations (and no need for more). So fold exit_type into
exit_reason, reducing the complexity of determining what really happened.
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM used to handle cpuid by letting userspace decide what values to
return to the guest. We now handle cpuid completely in the kernel. We
still let userspace decide which values the guest will see by having
userspace set up the value table beforehand (this is necessary to allow
management software to set the cpu features to the least common denominator,
so that live migration can work).
The motivation for the change is that kvm kernel code can be impacted by
cpuid features, for example the x86 emulator.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently when passing the a PIO emulation request to userspace, we
rely on userspace updating %rax (on 'in' instructions) and %rsi/%rdi/%rcx
(on string instructions). This (a) requires two extra ioctls for getting
and setting the registers and (b) is unfriendly to non-x86 archs, when
they get kvm ports.
So fix by doing the register fixups in the kernel and passing to userspace
only an abstract description of the PIO to be done.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instead of passing a 'struct kvm_run' back and forth between the kernel and
userspace, allocate a page and allow the user to mmap() it. This reduces
needless copying and makes the interface expandable by providing lots of
free space.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Unless we finally completely remove it, people will always add new users.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the PCI_MULTITHREAD_PROBE option that had already
been marked as broken.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces an optional function, arch_teardown_msi_irqs(),
which gives an arch the opportunity to do per-device teardown for
MSI/X. If that's not required, the default version simply calls
arch_teardown_msi_irq() for each msi irq required.
arch_teardown_msi_irqs() is simply passed a pdev, attached to the pdev
is a list of msi_descs, it is up to the arch to free the irq associated
with each of these as appropriate.
For archs that _don't_ implement arch_teardown_msi_irqs(), all msi_descs
with irq == 0 are considered unallocated, and the arch teardown routine
is not called on them.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces an optional function, arch_setup_msi_irqs(),
(note the plural) which gives an arch the opportunity to do per-device
setup for MSI/X and then allocate all the requested MSI/Xs at once.
If that's not required by the arch, the default version simply calls
arch_setup_msi_irq() for each MSI irq required.
arch_setup_msi_irqs() is passed a pdev, attached to the pdev is a list
of msi_descs with irq == 0, it is up to the arch to connect these up to
an irq (via set_irq_msi()) or return an error. For convenience the number
of vectors and the type are passed also.
All msi_descs with irq != 0 are considered allocated, and the arch
teardown routine will be called on them when necessary.
The existing semantics of pci_enable_msix() are that if the requested
number of irqs can not be allocated, the maximum number that _could_ be
allocated is returned. To support that, we define that in case of an
error from arch_setup_msi_irqs(), the number of msi_descs with irq != 0
are considered allocated, and are counted toward the "max that could be
allocated".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that we keep a list of msi descriptors, we don't need first_msi_irq
in the pci dev.
If we somehow have zero MSIs configured list_entry() will give us weird
oopes or nice memory corruption bugs. So be paranoid. Add BUG_ONs and also
a check in pci_msi_check_device() to make sure nvec > 0.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The msi descriptors are linked together with what looks a lot like
a linked list, but isn't a struct list_head list. Make it one.
The only complication is that previously we walked a list of irqs, and
got the descriptor for each with get_irq_msi(). Now we have a list of
descriptors and need to get the irq out of it, so it needs to be in the
actual struct msi_desc. We use 0 to indicate no irq is setup.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are currently several places in the kernel where we kmalloc()
a struct pci_dev and start initialising it. It'd be preferable to
have an allocator so we can ensure the pci_dev is correctly initialised
in one place.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an arch_check_device(), which gives archs a chance to check the input
to pci_enable_msi/x. The arch might be interested in the value of nvec so
pass it in. Propagate the error value returned from the arch routine out
to the caller.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Balance declarations of pci_request_regions() and pci_release_regions() with
empty inline definitions for the CONFIG_PCI=n case -- otherwise my patch to
drivers/net/3c59x.c in the -mm tree doesn't compile. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most architectures' scatterlist.h use the type dma_addr_t, but omit to
include <asm/types.h> which defines it. This could lead to build failures,
so let's add the missing includes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds a new API which can be used to issue various types
of PCI-E reset, including PCI-E warm reset and PCI-E hot reset.
This is needed for an ipr PCI-E adapter which does not properly
implement BIST. Running BIST on this adapter results in PCI-E
errors. The only reliable reset mechanism that exists on this
hardware is PCI Fundamental reset (warm reset). Since driving
this type of reset is architecture unique, this provides the
necessary hooks for architectures to add this support.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Almost all definitions used by file2alias was already
present in mod_devicetable.h.
Added the last definition and killed the input.h usage.
The errornous include was pointed out
by: Jan Engelhardt <jengelh@linux01.gwdg.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Jan Engelhardt <jengelh@linux01.gwdg.de>
Cc: Deepak Saxena <dsaxena@plexity.net>
There are two callers of __unlazy_fpu, unlazy_fpu and __switch_to, and
none of them appear to require additional preempt_disable/enable here.
Let's open-code save_init_fpu in __unlazy_fpu to save a few ops.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Andi Kleen <ak@suse.de>
RDTSCP is already synchronous and doesn't need an explicit CPUID.
This is a little faster and more importantly avoids VMEXITs on Hypervisors.
Original patch from Joerg Roedel, but reworked by AK
Also includes miscompilation fix by Eric Biederman
Cc: "Joerg Roedel" <joerg.roedel@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Redefine cpu_has() to evaluate cpu features already checked in early
boot at compile time. This way the compiler might eliminate some dead code.
Signed-off-by: Andi Kleen <ak@suse.de>
Check some CPUID bits that are needed for compiler generated early in boot.
When the system is still in real mode before changing the VESA BIOS mode
it is possible to still display an visible error message on the screen.
Similar to x86-64.
Includes cleanups from Eric Biederman
Signed-off-by: Andi Kleen <ak@suse.de>
- Introduce a wd_ops structure
- Convert the various nmi watchdogs over to it
- This allows to split the perfctr reservation from the watchdog
setup cleanly.
- Do perfctr reservation globally as it should have always been
- Remove dead code referenced only by unused EXPORT_SYMBOLs
Signed-off-by: Andi Kleen <ak@suse.de>
Add comment and condense code to make use of native_local_ptep_get_and_clear
function. Also, it turns out the 2-level and 3-level paging definitions were
identical, so move the common definition into pgtable.h
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
In situations where page table updates need only be made locally, and there is
no cross-processor A/D bit races involved, we need not use the heavyweight
xchg instruction to atomically fetch and clear page table entries. Instead,
we can just read and clear them directly.
This introduces a neat optimization for non-SMP kernels; drop the atomic xchg
operations from page table updates.
Thanks to Michel Lespinasse for noting this potential optimization.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
When exiting from an address space, no special hypervisor notification of page
table updates needs to occur; direct page table hypervisors, such as Xen,
switch to another address space first (init_mm) and unprotects the page tables
to avoid the cost of trapping to the hypervisor for each pte_clear. Shadow
mode hypervisors, such as VMI and lhype don't need to do the extra work of
calling through paravirt-ops, and can just directly clear the page table
entries without notifiying the hypervisor, since all the page tables are about
to be freed.
So introduce native_pte_clear functions which bypass any paravirt-ops
notification. This results in a significant performance win for VMI and
removes some indirect calls from zap_pte_range.
Note the 3-level paging already had a native_pte_clear function, thus
demanding argument conformance and extra args for the 2-level definition.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Use safe_apic_wait_icr_idle to check ICR idle bit if the vector is
NMI_VECTOR to avoid potential hangups in the event of crash when kdump
tries to stop the other CPUs.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
2007-05-02 19:27:18 +02:00
Fernando Luis [** ISO-8859-1 charset **] VzquezCao
Implement __send_IPI_dest_field which can be used to send IPIs when the
"destination shorthand" field of the ICR is set to 00 (destination
field). Use it whenever possible.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
apic_wait_icr_idle looks like this:
static __inline__ void apic_wait_icr_idle(void)
{
while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
cpu_relax();
}
The busy loop in this function would not be problematic if the
corresponding status bit in the ICR were always updated, but that does
not seem to be the case under certain crash scenarios. Kdump uses an IPI
to stop the other CPUs in the event of a crash, but when any of the
other CPUs are locked-up inside the NMI handler the CPU that sends the
IPI will end up looping forever in the ICR check, effectively
hard-locking the whole system.
Quoting from Intel's "MultiProcessor Specification" (Version 1.4), B-3:
"A local APIC unit indicates successful dispatch of an IPI by
resetting the Delivery Status bit in the Interrupt Command
Register (ICR). The operating system polls the delivery status
bit after sending an INIT or STARTUP IPI until the command has
been dispatched.
A period of 20 microseconds should be sufficient for IPI dispatch
to complete under normal operating conditions. If the IPI is not
successfully dispatched, the operating system can abort the
command. Alternatively, the operating system can retry the IPI by
writing the lower 32-bit double word of the ICR. This “time-out”
mechanism can be implemented through an external interrupt, if
interrupts are enabled on the processor, or through execution of
an instruction or time-stamp counter spin loop."
Intel's documentation suggests the implementation of a time-out
mechanism, which, by the way, is already being open-coded in some parts
of the kernel that tinker with ICR.
Create a apic_wait_icr_idle replacement that implements the time-out
mechanism and that can be used to solve the aforementioned problem.
AK: moved both functions out of line
AK: Added improved loop from Keith Owens
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
apic_wait_icr_idle looks like this:
static __inline__ void apic_wait_icr_idle(void)
{
while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
cpu_relax();
}
The busy loop in this function would not be problematic if the
corresponding status bit in the ICR were always updated, but that does
not seem to be the case under certain crash scenarios. Kdump uses an IPI
to stop the other CPUs in the event of a crash, but when any of the
other CPUs are locked-up inside the NMI handler the CPU that sends the
IPI will end up looping forever in the ICR check, effectively
hard-locking the whole system.
Quoting from Intel's "MultiProcessor Specification" (Version 1.4), B-3:
"A local APIC unit indicates successful dispatch of an IPI by
resetting the Delivery Status bit in the Interrupt Command
Register (ICR). The operating system polls the delivery status
bit after sending an INIT or STARTUP IPI until the command has
been dispatched.
A period of 20 microseconds should be sufficient for IPI dispatch
to complete under normal operating conditions. If the IPI is not
successfully dispatched, the operating system can abort the
command. Alternatively, the operating system can retry the IPI by
writing the lower 32-bit double word of the ICR. This “time-out”
mechanism can be implemented through an external interrupt, if
interrupts are enabled on the processor, or through execution of
an instruction or time-stamp counter spin loop."
Intel's documentation suggests the implementation of a time-out
mechanism, which, by the way, is already being open-coded in some parts
of the kernel that tinker with ICR.
Create a apic_wait_icr_idle replacement that implements the time-out
mechanism and that can be used to solve the aforementioned problem.
AK: moved both functions out of line
AK: added improved loop from Keith Owens
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
If our copy of the MTRRs of the BSP has RdMem or WrMem set, and
we are running on an AMD64/K8 system, the boot CPU must have had
MtrrFixDramEn and MtrrFixDramModEn set (otherwise our RDMSR would
have copied these bits cleared), so we set them on this CPU as well.
This allows us to keep the AMD64/K8 RdMem and WrMem bits in sync
across the CPUs of SMP systems in order to fullfill the duty of
system software to "initialize and maintain MTRR consistency
across all processors." as written in the AMD and Intel manuals.
If an WRMSR instruction fails because MtrrFixDramModEn is not
set, I expect that also the Intel-style MTRR bits are not updated.
AK: minor cleanup, moved MSR defines around
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Applied fix by Andew Morton:
http://lkml.org/lkml/2007/4/8/88 - Fix `make headers_check'.
AMD and Intel x86 CPU manuals state that it is the responsibility of
system software to initialize and maintain MTRR consistency across
all processors in Multi-Processing Environments.
Quote from page 188 of the AMD64 System Programming manual (Volume 2):
7.6.5 MTRRs in Multi-Processing Environments
"In multi-processing environments, the MTRRs located in all processors must
characterize memory in the same way. Generally, this means that identical
values are written to the MTRRs used by the processors." (short omission here)
"Failure to do so may result in coherency violations or loss of atomicity.
Processor implementations do not check the MTRR settings in other processors
to ensure consistency. It is the responsibility of system software to
initialize and maintain MTRR consistency across all processors."
Current Linux MTRR code already implements the above in the case that the
BIOS does not properly initialize MTRRs on the secondary processors,
but the case where the fixed-range MTRRs of the boot processor are changed
after Linux started to boot, before the initialsation of a secondary
processor, is not handled yet.
In this case, secondary processors are currently initialized by Linux
with MTRRs which the boot processor had very early, when mtrr_bp_init()
did run, but not with the MTRRs which the boot processor uses at the
time when that secondary processors is actually booted,
causing differing MTRR contents on the secondary processors.
Such situation happens on Acer Ferrari 1000 and 5000 notebooks where the
BIOS enables and sets AMD-specific IORR bits in the fixed-range MTRRs
of the boot processor when it transitions the system into ACPI mode.
The SMI handler of the BIOS does this in SMM, entered while Linux ACPI
code runs acpi_enable().
Other occasions where the SMI handler of the BIOS may change bits in
the MTRRs could occur as well. To initialize newly booted secodary
processors with the fixed-range MTRRs which the boot processor uses
at that time, this patch saves the fixed-range MTRRs of the boot
processor before new secondary processors are started. When the
secondary processors run their Linux initialisation code, their
fixed-range MTRRs will be updated with the saved fixed-range MTRRs.
If CONFIG_MTRR is not set, we define mtrr_save_state
as an empty statement because there is nothing to do.
Possible TODOs:
*) CPU-hotplugging outside of SMP suspend/resume is not yet tested
with this patch.
*) If, even in this case, an AP never runs i386/do_boot_cpu or x86_64/cpu_up,
then the calls to mtrr_save_state() could be replaced by calls to
mtrr_save_fixed_ranges(NULL) and mtrr_save_state() would not be
needed.
That would need either verification of the CPU-hotplug code or
at least a test on a >2 CPU machine.
*) The MTRRs of other running processors are not yet checked at this
time but it might be interesting to syncronize the MTTRs of all
processors before booting. That would be an incremental patch,
but of rather low priority since there is no machine known so
far which would require this.
AK: moved prototypes on x86-64 around to fix warnings
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
