use __le64 annotated variable for response buffer address as this is
read in little endian format form the register.
This suppresses sparse warning
drivers/char/tpm/tpm_crb.c:558:18: warning: cast to restricted __le64
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The correct sequence is to first request locality and only after
that perform cmd_ready handshake, otherwise the hardware will drop
the subsequent message as from the device point of view the cmd_ready
handshake wasn't performed. Symmetrically locality has to be relinquished
only after going idle handshake has completed, this requires that
go_idle has to poll for the completion and as well locality
relinquish has to poll for completion so it is not overridden
in back to back commands flow.
Two wrapper functions are added (request_locality relinquish_locality)
to simplify the error handling.
The issue is only visible on devices that support multiple localities.
Fixes: 877c57d0d0 ("tpm_crb: request and relinquish locality 0")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
This patch gets rid of dealing with intermediate flag for start method
and use start method value from ACPI table directly.
For ARM64, the locality is handled by Trust Zone in FW. The layout
does not have crb_regs_head. It is hitting the following line.
dev_warn(dev, FW_BUG "Bad ACPI memory layout");
Current code excludes CRB_FL_ACPI_START for this check. Now since
ARM64 support for TPM CRB is added, CRB_FL_CRB_SMC_START should also be
excluded from this check.
For goIdle and cmdReady where code was excluding CRB_FL_ACPI_START only
(do nothing for ACPI start method), CRB_FL_CRB_SMC_START was also
excluded as ARM64 SMC start method does not have TPM_CRB_CTRL_REQ.
However with special PPT workaround requiring CRB_FL_CRB_START to be
set in addition to CRB_FL_ACPI_START and the addition flag of SMC
start method CRB_FL_CRB_SMC_START, the code has become difficult to
maintain and undrestand. It is better to make code deal with start
method value from ACPI table directly.
Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4198 608 0 4806 12c6 drivers/char/tpm/tpm_crb.o
File size After adding 'const':
text data bss dec hex filename
4262 520 0 4782 12ae drivers/char/tpm/tpm_crb.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
priv->cmd_size is never initialised if the cmd and rsp buffers reside
at different addresses. Initialise it in the exit path of the function
when rsp buffer has also been successfully allocated.
Fixes: aa77ea0e43 ("tpm/tpm_crb: cache cmd_size register value.").
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
- Update the ACPICA code in the kernel to upstream revision
revision 20170531 (which covers all of the new material from
ACPI 6.2) including:
* Support for the PinFunction(), PinConfig(), PinGroup(),
PinGroupFunction(), and PinGroupConfig() resource descriptors
(Mika Westerberg).
* Support for new subtables in HEST and SRAT, new notify value
for HEST, header support for TPM2 table changes, and BGRT
Status field update (Bob Moore).
* Support for new PCCT subtables (David Box).
* Support for _LSI, _LSR, _LSW, and _HMA as predefined methods
(Erik Schmauss).
* Support for the new WSMT, HMAT, and PPTT tables (Lv Zheng).
* New UUID values for Processor Properties (Bob Moore).
* New notify values for memory attributes and graceful shutdown
(Bob Moore).
* Fix related to the PCAT_COMPAT MADT flag (Janosch Hildebrand).
* Resource to AML conversion fix for resources containing GPIOs
(Mika Westerberg).
* Disassembler-related updates (Bob Moore, David Box, Erik
Schmauss).
* Assorted fixes and cleanups (Bob Moore, Erik Schmauss, Lv Zheng,
Cao Jin).
- Modify ACPICA to always use designated initializers for function
pointer structures to make the structure layout randomization GCC
plugin work with it (Kees Cook).
- Update the tables configfs interface to unload SSDTs on configfs
entry removal (Jan Kiszka).
- Add support for the GPI1 regulator to the xpower PMIC Operation
Region handler (Hans de Goede).
- Fix ACPI EC issues related to conflicting EC definitions in the
ECDT and in the ACPI namespace (Lv Zheng, Carlo Caione, Chris
Chiu).
- Fix an interrupt storm issue in the EC driver and make its debug
output work with dynamic debug as expected (Lv Zheng).
- Add ACPI backlight quirk for Dell Precision 7510 (Shih-Yuan Lee).
- Fix whitespace in pr_fmt() to align log entries properly in some
places in the ACPI subsystem (Vincent Legoll).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ImFw
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These mostly update the ACPICA code in the kernel to upstream revision
20170531 which covers all of the new material from ACPI 6.2, including
new tables (WSMT, HMAT, PPTT), new subtables and definition changes
for some existing tables (BGRT, HEST, SRAT, TPM2, PCCT), new resource
descriptor macros for pin control, support for new predefined methods
(_LSI, _LSR, _LSW, _HMA), fixes and cleanups.
On top of that, an additional ACPICA change from Kees (which also is
upstream already) switches all of the definitions of function pointer
structures in ACPICA to use designated initializers so as to make the
structure layout randomization GCC plugin work with it.
The rest is a few fixes and cleanups in the EC driver, an xpower PMIC
driver update, a new backlight blacklist entry, and update of the
tables configfs interface and a messages formatting cleanup.
Specifics:
- Update the ACPICA code in the kernel to upstream revision revision
20170531 (which covers all of the new material from ACPI 6.2)
including:
* Support for the PinFunction(), PinConfig(), PinGroup(),
PinGroupFunction(), and PinGroupConfig() resource descriptors
(Mika Westerberg).
* Support for new subtables in HEST and SRAT, new notify value for
HEST, header support for TPM2 table changes, and BGRT Status
field update (Bob Moore).
* Support for new PCCT subtables (David Box).
* Support for _LSI, _LSR, _LSW, and _HMA as predefined methods
(Erik Schmauss).
* Support for the new WSMT, HMAT, and PPTT tables (Lv Zheng).
* New UUID values for Processor Properties (Bob Moore).
* New notify values for memory attributes and graceful shutdown
(Bob Moore).
* Fix related to the PCAT_COMPAT MADT flag (Janosch Hildebrand).
* Resource to AML conversion fix for resources containing GPIOs
(Mika Westerberg).
* Disassembler-related updates (Bob Moore, David Box, Erik
Schmauss).
* Assorted fixes and cleanups (Bob Moore, Erik Schmauss, Lv Zheng,
Cao Jin).
- Modify ACPICA to always use designated initializers for function
pointer structures to make the structure layout randomization GCC
plugin work with it (Kees Cook).
- Update the tables configfs interface to unload SSDTs on configfs
entry removal (Jan Kiszka).
- Add support for the GPI1 regulator to the xpower PMIC Operation
Region handler (Hans de Goede).
- Fix ACPI EC issues related to conflicting EC definitions in the
ECDT and in the ACPI namespace (Lv Zheng, Carlo Caione, Chris
Chiu).
- Fix an interrupt storm issue in the EC driver and make its debug
output work with dynamic debug as expected (Lv Zheng).
- Add ACPI backlight quirk for Dell Precision 7510 (Shih-Yuan Lee).
- Fix whitespace in pr_fmt() to align log entries properly in some
places in the ACPI subsystem (Vincent Legoll)"
* tag 'acpi-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
ACPI / EC: Add quirk for GL720VMK
ACPI / EC: Fix media keys not working problem on some Asus laptops
ACPI / EC: Add support to skip boot stage DSDT probe
ACPI / EC: Enhance boot EC sanity check
ACPI / video: Add quirks for the Dell Precision 7510
ACPI: EC: Fix EC command visibility for dynamic debug
ACPI: EC: Fix an EC event IRQ storming issue
ACPICA: Use designated initializers
ACPICA: Update version to 20170531
ACPICA: Update a couple of debug output messages
ACPICA: acpiexec: enhance local signal handler
ACPICA: Simplify output for the ACPI Debug Object
ACPICA: Unix application OSL: Correctly handle control-c (EINTR)
ACPICA: Improvements for debug output only
ACPICA: Disassembler: allow conflicting external declarations to be emitted.
ACPICA: Disassembler: add external op to namespace on first pass
ACPICA: Disassembler: prevent external op's from opening a new scope
ACPICA: Changed Gbl_disasm_flag to acpi_gbl_disasm_flag
ACPICA: Changing External to a named object
ACPICA: Update two error messages to emit control method name
...
ACPICA commit b922ecaf9053dae3b8933664e951ed1ee8f86f07
Update to new version of the TCG/ACPI spec.
Does not include table compiler or disassembler support.
Link: https://github.com/acpica/acpica/commit/b922ecaf
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove a useless constant that slipped through me when I did the code
review. This commit fixes the issue.
Cc: Jiandi An <anjiandi@codeaurora.org>
Fixes: 69c558de63c7 ("tpm/tpm_crb: Enable TPM CRB interface for ARM64")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This enables TPM Command Response Buffer interface driver for
ARM64 and implements an ARM specific TPM CRB start method that
invokes a Secure Monitor Call (SMC) to request the TrustZone
Firmware to execute or cancel a TPM 2.0 command.
In ARM, TrustZone security extensions enable a secure software
environment with Secure Monitor mode. A Secure Monitor Call
(SMC) is used to enter the Secure Monitor mode and perform a
Secure Monitor service to communicate with TrustZone firmware
which has control over the TPM hardware.
Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (on x86/PTT)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This commit adds support for requesting and relinquishing locality 0 in
tpm_crb for the course of command transmission.
In order to achieve this, two new callbacks are added to struct
tpm_class_ops:
- request_locality
- relinquish_locality
With CRB interface you first set either requestAccess or relinquish bit
from TPM_LOC_CTRL_x register and then wait for locAssigned and
tpmRegValidSts bits to be set in the TPM_LOC_STATE_x register.
The reason why were are doing this is to make sure that the driver
will work properly with Intel TXT that uses locality 2. There's no
explicit guarantee that it would relinquish this locality. In more
general sense this commit enables tpm_crb to be a well behaving
citizen in a multi locality environment.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
When PM_SLEEP is disabled crb_pm_suspend and crb_pm_resume are not used by
SET_SYSTEM_SLEEP_PM_OPS even if PM is enabled:
drvers/char/tpm/tpm_crb.c:540:12: warning: ‘crb_pm_suspend’ defined but not
used [-Wunused-function]
static int crb_pm_suspend(struct device *dev)
^
drivers/char/tpm/tpm_crb.c:551:12: warning: ‘crb_pm_resume’ defined but not
used [-Wunused-function]
static int crb_pm_resume(struct device *dev)
^
The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However, this patch fixes this warning by using __maybe_unused on function
that are in the preprocessor condition.
Fixes: 848efcfb560c ("tpm/tpm_crb: enter the low power state upon device suspend")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.
Cc: stable@vger.kernel.org
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Encapsulated crb_wait_for_reg32() so that state changes in other CRB
registers than TPM_CRB_CTRL_REQ_x can be waited.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>
In order to provide access to locality registers, this commits adds
mapping of the head of the CRB registers, which are located right
before the control area.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>
This fix enables a platform to enter the idle state (suspend-to-idle)
The driver needs to request explicitly go_idle upon completion
from the pm suspend handler.
The runtime pm is disabled on suspend during prepare state by calling
pm_runtime_get_noresume, hence we cannot relay on runtime pm to leave
the device in low power state. Symmetrically cmdReady is called
upon resume.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Siged-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The expectation is that the if the CRB cmd/rsp buffer falls within the
ACPI region that the entire buffer will be within the reason. Otherwise
resource reservation will fail when it crosses regions.
Work around this BIOS bug by limiting the cmd/rsp buffer to the length
of the declared ACPI region. BIOS vendors should fix this by making
the ACPI and register length declarations consistent.
Reported-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
crb_check_resource() in TPM CRB driver calls
acpi_dev_resource_memory() which only handles 32-bit resources.
Adding a call to acpi_dev_resource_address_space() in TPM CRB
driver which handles 64-bit resources.
Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not compiled in or enabled, the device
will be in the permanent ready state.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.
The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.
Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'
To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.
[jarkko.sakkinen@linux.intel.com: removed cmdReady debug trace on a
success case due the heavy amount of log traffic it causes.]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not enabled, the device will be in
ready state.
[jarkko.sakkinen@linux.intel.com: changed pm_runtime_put_sync()
to pm_runtime_put()]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.
The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.
Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'
To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Because of the line break in the debug print the chackpatch is
not silent on 80 characters limitation.
The easiest fix is to straighten the lines, it's also more readable.
WARNING: line over 80 characters
+ FW_BUG "TPM2 ACPI table does not define a memory
resource\n");
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Don't apply endianity conversion when writing to the registers
this is already handled by the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Instead of expensive register access on retrieving cmd_size
on each send, save the value during initialization in the private
context. The value doesn't change.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The platform device is not used in this driver, drop the
include to linux/platform_device.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Renamed CRB protocol specific constants to match the TCG PC Client
Platform TPM Profile (PTP) Specification and driver status constants
to be explicit that they are driver specific.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.
The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:
* Cancel might not happen.
* req_canceled() always returns zero.
A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.
CC: stable@vger.kernel.org
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The TCG standard startup sequence (get timeouts, tpm startup, etc) for
TPM and TPM2 chips is being open coded in many drivers, move it into
the core code.
tpm_tis and tpm_crb are used as the basis for the core code
implementation and the easy drivers are converted. In the process
several small drivers bugs relating to error handling this flow
are fixed.
For now the flag TPM_OPS_AUTO_STARTUP is optional to allow a staged
driver roll out, but ultimately all drivers should use this flow and
the flag removed. Some drivers still do not implement the startup
sequence at all and will need to be tested with it enabled.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Remove useless priv field in struct tpm_vendor_specific and take benefit
of chip->dev.driver_data. As priv is the latest field available in
struct tpm_vendor_specific, remove any reference to that structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
On my Lenovo x250 the following situation occurs:
[18697.813871] tpm_crb MSFT0101:00: can't request region for resource
[mem 0xacdff080-0xacdfffff]
The mapping of the control area overlaps the mapping of the command
buffer. The control area is mapped over page, which is not right. It
should mapped over sizeof(struct crb_control_area).
Fixing this issue unmasks another issue. Command and response buffers
can overlap and they do interleave on this machine. According to the PTP
specification the overlapping means that they are mapped to the same
buffer.
The commit has been also on a Haswell NUC where things worked before
applying this fix so that the both code paths for response buffer
initialization are tested.
Cc: stable@vger.kernel.org
Fixes: 1bd047be37 ("tpm_crb: Use devm_ioremap_resource")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
The iomem resource is needed only temporarily so it is better to pass
it on instead of storing it permanently. Named the variable as io_res
so that the code better documents itself.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
rmmod crashes the driver because tpm_chip_unregister() already sets ops
to NULL. This commit fixes the issue by moving tpm2_shutdown() to
tpm_chip_unregister(). This commit is also cleanup because it removes
duplicate code from tpm_crb and tpm_tis to the core.
Fixes: 4d3eac5e156a ("tpm: Provide strong locking for device removal")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
In all cases use dev_name() for the mapped resources. This is both
for sake of consistency and also with some platforms resource name
given by ACPI object seems to return garbage.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: 1bd047be37 ("tpm_crb: Use devm_ioremap_resource")
To support the force mode in tpm_tis we need to use resource locking
in tpm_crb as well, via devm_ioremap_resource.
The light restructuring better aligns crb and tis and makes it easier
to see the that new changes make sense.
The control area and its associated buffers do not always fall in the
range of the iomem resource given by the ACPI object. This patch fixes
the issue by mapping the buffers if this is the case.
[jarkko.sakkinen@linux.intel.com: squashed update described in the
last paragraph.]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
ioread32 and readl are defined to read from PCI style memory, ie little
endian and return the result in host order. On platforms where a
swap is required ioread32/readl do the swap internally (eg see ppc).
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
include/acpi/actbl2.h is the proper place for these definitions
and the needed TPM2 ones have been there since
commit 413d4a6def ("ACPICA: Update TPM2 ACPI table")
This also drops a couple of le32_to_cpu's for members of this table,
the existing swapping was not done consistently, and the standard
used by other Linux callers of acpi_get_table is unswapped.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
IRQ probing needs to know that the TPM is working before trying to
probe, so move tpm_get_timeouts() to the top of the tpm_tis_init().
This has the advantage of also getting the correct timeouts loaded
before doing IRQ probing.
All the timeout handling code is moved to tpm_get_timeouts() in order to
remove duplicate code in tpm_tis and tpm_crb.
[jarkko.sakkinen@linux.intel.com: squashed two patches together and
improved the commit message.]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
