With the introduction of the linear mapped p2m list setting memory
areas to "invalid" had to be delayed. When doing the invalidation
make sure no zero sized areas are processed.
Signed-off-by: Juegren Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When converting a pfn to a physical address be sure to use 64 bit
wide types or convert the physical address to a pfn if possible.
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When allocating a new pmd for the linear mapped p2m list a check is
done for not introducing another pmd when this just happened on
another cpu. In this case the old pte pointer was returned which
points to the p2m_missing or p2m_identity page. The correct value
would be the pointer to the found new page.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
In xen_rebuild_p2m_list() for large areas of invalid or identity
mapped memory the pmd entries on 32 bit systems are initialized
wrong. Correct this error.
Suggested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
In case kasprintf() fails in xen_setup_timer() we assign name to the
static string "<timer kasprintf failed>". We, however, don't check
that fact before issuing kfree() in xen_teardown_timer(), kernel is
supposed to crash with 'kernel BUG at mm/slub.c:3341!'
Solve the issue by making name a fixed length string inside struct
xen_clock_event_device. 16 bytes should be enough.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
If the non-RAM regions in the e820 memory map are larger than the size
of the initial balloon, a BUG was triggered as the frames are remaped
beyond the limit of the linear p2m. The frames are remapped into the
initial balloon area (xen_extra_mem) but not enough of this is
available.
Ensure enough extra memory regions are added for these remapped
frames.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
This accounting is just used to print a diagnostic message that isn't
very useful.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
With recent changes in p2m we now have legitimate cases when
p2m memory needs to be freed during early boot (i.e. before
slab is initialized).
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
There is no reason for having it and, with commit 250a1ac685 ("x86,
smpboot: Remove pointless preempt_disable() in
native_smp_prepare_cpus()"), it prevents HVM guests from booting.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
With the virtual mapped linear p2m list the post-init mmu operations
must be used for setting up the p2m mappings, as in case of
CONFIG_FLATMEM the init routines may trigger BUGs.
paging_init() sets up all infrastructure needed to switch to the
post-init mmu ops done by xen_post_allocator_init(). With the virtual
mapped linear p2m list we need some mmu ops during setup of this list,
so we have to switch to the correct mmu ops as soon as possible.
The p2m list is usable from the beginning, just expansion requires to
have established the new linear mapping. So the call of
xen_remap_memory() had to be introduced, but this is not due to the
mmu ops requiring this.
Summing it up: calling xen_post_allocator_init() not directly after
paging_init() was conceptually wrong in the beginning, it just didn't
matter up to now as no functions used between the two calls needed
some critical mmu ops (e.g. alloc_pte). This has changed now, so I
corrected it.
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 5b8e7d8054 removed the __init
annotation from xen_set_identity_and_remap_chunk(). Add it again.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Introduce two helper functions to safely read and write unsigned long
values from or to memory when the access may fault because the mapping
is non-present or read-only.
These helpers can be used instead of open coded uses of __get_user()
and __put_user() avoiding the need to do casts to fix sparse warnings.
Use the helpers in page.h and p2m.c. This will fix the sparse
warnings when doing "make C=1".
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Instead of checking at each call of set_phys_to_machine() whether a
new p2m page has to be allocated due to writing an entry in a large
invalid or identity area, just map those areas read only and react
to a page fault on write by allocating the new page.
This change will make the common path with no allocation much
faster as it only requires a single write of the new mfn instead
of walking the address translation tables and checking for the
special cases.
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
At start of the day the Xen hypervisor presents a contiguous mfn list
to a pv-domain. In order to support sparse memory this mfn list is
accessed via a three level p2m tree built early in the boot process.
Whenever the system needs the mfn associated with a pfn this tree is
used to find the mfn.
Instead of using a software walked tree for accessing a specific mfn
list entry this patch is creating a virtual address area for the
entire possible mfn list including memory holes. The holes are
covered by mapping a pre-defined page consisting only of "invalid
mfn" entries. Access to a mfn entry is possible by just using the
virtual base address of the mfn list and the pfn as index into that
list. This speeds up the (hot) path of determining the mfn of a
pfn.
Kernel build on a Dell Latitude E6440 (2 cores, HT) in 64 bit Dom0
showed following improvements:
Elapsed time: 32:50 -> 32:35
System: 18:07 -> 17:47
User: 104:00 -> 103:30
Tested with following configurations:
- 64 bit dom0, 8GB RAM
- 64 bit dom0, 128 GB RAM, PCI-area above 4 GB
- 32 bit domU, 512 MB, 8 GB, 43 GB (more wouldn't work even without
the patch)
- 32 bit domU, ballooning up and down
- 32 bit domU, save and restore
- 32 bit domU with PCI passthrough
- 64 bit domU, 8 GB, 2049 MB, 5000 MB
- 64 bit domU, ballooning up and down
- 64 bit domU, save and restore
- 64 bit domU with PCI passthrough
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Today get_phys_to_machine() is always called when the mfn for a pfn
is to be obtained. Add a wrapper __pfn_to_mfn() as inline function
to be able to avoid calling get_phys_to_machine() when possible as
soon as the switch to a linear mapped p2m list has been done.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Introduces lookup_pmd_address() to get the address of the pmd entry
related to a virtual address in the current address space. This
function is needed for support of a virtual mapped sparse p2m list
in xen pv domains, as we need the address of the pmd entry, not the
one of the pte in that case.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When the physical memory configuration is initialized the p2m entries
for not pouplated memory pages are set to "invalid". As those pages
are beyond the hypervisor built p2m list the p2m tree has to be
extended.
This patch delays processing the extra memory related p2m entries
during the boot process until some more basic memory management
functions are callable. This removes the need to create new p2m
entries until virtual memory management is available.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The m2p overrides are used to be able to find the local pfn for a
foreign mfn mapped into the domain. They are used by driver backends
having to access frontend data.
As this functionality isn't used in early boot it makes no sense to
initialize the m2p override functions very early. It can be done
later without doing any harm, removing the need for allocating memory
via extend_brk().
While at it make some m2p override functions static as they are only
used internally.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Early in the boot process the memory layout of a pv-domain is changed
to match the E820 map (either the host one for Dom0 or the Xen one)
regarding placement of RAM and PCI holes. This requires removing memory
pages initially located at positions not suitable for RAM and adding
them later at higher addresses where no restrictions apply.
To be able to operate on the hypervisor supported p2m list until a
virtual mapped linear p2m list can be constructed, remapping must
be delayed until virtual memory management is initialized, as the
initial p2m list can't be extended unlimited at physical memory
initialization time due to it's fixed structure.
A further advantage is the reduction in complexity and code volume as
we don't have to be careful regarding memory restrictions during p2m
updates.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
In arch/x86/xen/p2m.c three different allocation functions for
obtaining a memory page are used: extend_brk(), alloc_bootmem_align()
or __get_free_page(). Which of those functions is used depends on the
progress of the boot process of the system.
Introduce a common allocation routine selecting the to be called
allocation routine dynamically based on the boot progress. This allows
moving initialization steps without having to care about changing
allocation calls.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Some functions in arch/x86/xen/p2m.c are used locally only. Make them
static. Rearrange the functions in p2m.c to avoid forward declarations.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The source arch/x86/xen/p2m.c has some coding style issues. Fix them.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When hardware supports APIC/x2APIC virtualization we don't need to use
pirqs for MSI handling and instead use APIC since most APIC accesses
(MMIO or MSR) will now be processed without VMEXITs.
As an example, netperf on the original code produces this profile
(collected wih 'xentrace -e 0x0008ffff -T 5'):
342 cpu_change
260 CPUID
34638 HLT
64067 INJ_VIRQ
28374 INTR
82733 INTR_WINDOW
10 NPF
24337 TRAP
370610 vlapic_accept_pic_intr
307528 VMENTRY
307527 VMEXIT
140998 VMMCALL
127 wrap_buffer
After applying this patch the same test shows
230 cpu_change
260 CPUID
36542 HLT
174 INJ_VIRQ
27250 INTR
222 INTR_WINDOW
20 NPF
24999 TRAP
381812 vlapic_accept_pic_intr
166480 VMENTRY
166479 VMEXIT
77208 VMMCALL
81 wrap_buffer
ApacheBench results (ab -n 10000 -c 200) improve by about 10%
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
If the hardware supports APIC virtualization we may decide not to use
pirqs and instead use APIC/x2APIC directly, meaning that we don't want
to set x86_msi.setup_msi_irqs and x86_msi.teardown_msi_irq to
Xen-specific routines. However, x2APIC is not set up by the time
pci_xen_hvm_init() is called so we need to postpone setting these ops
until later, when we know which APIC mode is used.
(Note that currently x2APIC is never initialized on HVM guests. This
may change in the future)
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Introduce an arch specific function to find out whether a particular dma
mapping operation needs to bounce on the swiotlb buffer.
On ARM and ARM64, if the page involved is a foreign page and the device
is not coherent, we need to bounce because at unmap time we cannot
execute any required cache maintenance operations (we don't know how to
find the pfn from the mfn).
No change of behaviour for x86.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
dev_addr is the machine address of the page.
The new parameter can be used by the ARM and ARM64 implementations of
xen_dma_map_page to find out if the page is a local page (pfn == mfn) or
a foreign page (pfn != mfn).
dev_addr could be retrieved again from the physical address, using
pfn_to_mfn, but it requires accessing an rbtree. Since we already have
the dev_addr in our hands at the call site there is no need to get the
mfn twice.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 call do_notify_resume on paranoid returns if TIF_UPROBE is set but
not on non-paranoid returns. I suspect that this is a mistake and that
the code only works because int3 is paranoid.
Setting _TIF_NOTIFY_RESUME in the uprobe code was probably a workaround
for the x86 bug. With that bug fixed, we can remove _TIF_NOTIFY_RESUME
from the uprobes code.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge x86-64 iret fixes from Andy Lutomirski:
"This addresses the following issues:
- an unrecoverable double-fault triggerable with modify_ldt.
- invalid stack usage in espfix64 failed IRET recovery from IST
context.
- invalid stack usage in non-espfix64 failed IRET recovery from IST
context.
It also makes a good but IMO scary change: non-espfix64 failed IRET
will now report the correct error. Hopefully nothing depended on the
old incorrect behavior, but maybe Wine will get confused in some
obscure corner case"
* emailed patches from Andy Lutomirski <luto@amacapital.net>:
x86_64, traps: Rework bad_iret
x86_64, traps: Stop using IST for #SS
x86_64, traps: Fix the espfix64 #DF fixup and rewrite it in C
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes: 3891a04aaf
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Thomas Gleixner:
"Misc fixes:
- gold linker build fix
- noxsave command line parsing fix
- bugfix for NX setup
- microcode resume path bug fix
- _TIF_NOHZ versus TIF_NOHZ bugfix as discussed in the mysterious
lockup thread"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, syscall: Fix _TIF_NOHZ handling in syscall_trace_enter_phase1
x86, kaslr: Handle Gold linker for finding bss/brk
x86, mm: Set NX across entire PMD at boot
x86, microcode: Update BSPs microcode on resume
x86: Require exact match for 'noxsave' command line option
Pull perf fixes from Ingo Molnar:
"Misc fixes: two Intel uncore driver fixes, a CPU-hotplug fix and a
build dependencies fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix boot crash on SBOX PMU on Haswell-EP
perf/x86/intel/uncore: Fix IRP uncore register offsets on Haswell EP
perf: Fix corruption of sibling list with hotplug
perf/x86: Fix embarrasing typo
TIF_NOHZ is 19 (i.e. _TIF_SYSCALL_TRACE | _TIF_NOTIFY_RESUME |
_TIF_SINGLESTEP), not (1<<19).
This code is involved in Dave's trinity lockup, but I don't see why
it would cause any of the problems he's seeing, except inadvertently
by causing a different path through entry_64.S's syscall handling.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/a6cd3b60a3f53afb6e1c8081b0ec30ff19003dd7.1416434075.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When building with the Gold linker, the .bss and .brk areas of vmlinux
are shown as consecutive instead of having the same file offset. Allow
for either state, as long as things add up correctly.
Fixes: e6023367d7 ("x86, kaslr: Prevent .bss from overlaping initrd")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Junjie Mao <eternal.n08@gmail.com>
Link: http://lkml.kernel.org/r/20141118001604.GA25045@www.outflux.net
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When setting up permissions on kernel memory at boot, the end of the
PMD that was split from bss remained executable. It should be NX like
the rest. This performs a PMD alignment instead of a PAGE alignment to
get the correct span of memory.
Before:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82c00000 10M RW PSE GLB NX pmd
0xffffffff82c00000-0xffffffff82df5000 2004K RW GLB NX pte
0xffffffff82df5000-0xffffffff82e00000 44K RW GLB x pte
0xffffffff82e00000-0xffffffffc0000000 978M pmd
After:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82e00000 12M RW PSE GLB NX pmd
0xffffffff82e00000-0xffffffffc0000000 978M pmd
[ tglx: Changed it to roundup(_brk_end, PMD_SIZE) and added a comment.
We really should unmap the reminder along with the holes
caused by init,initdata etc. but thats a different issue ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20141114194737.GA3091@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the situation when we apply early microcode but do *not* apply late
microcode, we fail to update the BSP's microcode on resume because we
haven't initialized the uci->mc microcode pointer. So, in order to
alleviate that, we go and dig out the stashed microcode patch during
early boot. It is basically the same thing that is done on the APs early
during boot so do that too here.
Tested-by: alex.schnaidt@gmail.com
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=88001
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20141118094657.GA6635@pd.tnic
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 fixes from Ingo Molnar:
"Microcode fixes, a Xen fix and a KASLR boot loading fix with certain
memory layouts"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Fix ucode patch stashing on 32-bit
x86/core, x86/xen/smp: Use 'die_complete' completion when taking CPU down
x86, microcode: Fix accessing dis_ucode_ldr on 32-bit
x86, kaslr: Prevent .bss from overlaping initrd
x86, microcode, AMD: Fix early ucode loading on 32-bit
Al Viro pointed out that the x86-64 csum_partial_copy_from_user() is
somewhat confused about what it should do on errors, notably it mostly
clears the uncopied end result buffer, but misses that for the initial
alignment case.
All users should check for errors, so it's dubious whether the clearing
is even necessary, and Al also points out that we should probably clean
up the calling conventions, but regardless of any future changes to this
function, the fact that it is inconsistent is just annoying.
So make the __get_user() failure path use the same error exit as all the
other errors do.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have some very similarly named command-line options:
arch/x86/kernel/cpu/common.c:__setup("noxsave", x86_xsave_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaveopt", x86_xsaveopt_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaves", x86_xsaves_setup);
__setup() is designed to match options that take arguments, like
"foo=bar" where you would have:
__setup("foo", x86_foo_func...);
The problem is that "noxsave" actually _matches_ "noxsaves" in
the same way that "foo" matches "foo=bar". If you boot an old
kernel that does not know about "noxsaves" with "noxsaves" on the
command line, it will interpret the argument as "noxsave", which
is not what you want at all.
This makes the "noxsave" handler only return success when it finds
an *exact* match.
[ tglx: We really need to make __setup() more robust. ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: x86@kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20141111220133.FE053984@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There were several reports that on some systems writing the SBOX0 PMU
initialization MSR would #GP at boot. This did not happen on all
systems -- my two test systems booted fine.
Writing the three initialization bits bit-by-bit seems to avoid the
problem. So add a special callback to do just that.
This replaces an earlier patch that disabled the SBOX.
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-and-Tested-by: Patrick Lu <patrick.lu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: http://lkml.kernel.org/r/1415062828-19759-4-git-send-email-andi@firstfloor.org
[ Fixed a whitespace error and added attribution tags that were left out inexplicably. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The counter register offsets for the IRP box PMU for Haswell-EP
were incorrect. The offsets actually changed over IvyBridge EP.
Fix them to the correct values. For this we need to fork the read
function from the IVB and use an own counter array.
Tested-by: patrick.lu@intel.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: http://lkml.kernel.org/r/1415062828-19759-3-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* access the dis_ucode_ldr chicken bit properly
* fix patch stashing on AMD on 32-bit
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BamU
-----END PGP SIGNATURE-----
Merge tag 'microcode_fixes_for_3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/urgent
Pull two fixes for early microcode loader on 32-bit from Borislav Petkov:
- access the dis_ucode_ldr chicken bit properly
- fix patch stashing on AMD on 32-bit
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Save the patch while we're running on the BSP instead of later, before
the initrd has been jettisoned. More importantly, on 32-bit we need to
access the physical address instead of the virtual.
This way we actually do find it on the APs instead of having to go
through the initrd each time.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 5335ba5cf4 ("x86, microcode, AMD: Fix early ucode loading")
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Borislav Petkov <bp@suse.de>
Commit 2ed53c0d6c ("x86/smpboot: Speed up suspend/resume by
avoiding 100ms sleep for CPU offline during S3") introduced
completions to CPU offlining process. These completions are not
initialized on Xen kernels causing a panic in
play_dead_common().
Move handling of die_complete into common routines to make them
available to Xen guests.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: tianyu.lan@intel.com
Cc: konrad.wilk@oracle.com
Cc: xen-devel@lists.xenproject.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1414770572-7950-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We should be accessing it through a pointer, like on the BSP.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 65cef1311d ("x86, microcode: Add a disable chicken bit")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Borislav Petkov <bp@suse.de>
The emulator could reuse an op->type from a previous instruction for some
immediate values. If it mistakenly considers the operands as memory
operands, it will performs a memory read and overwrite op->val.
Consider for instance the ROR instruction - src2 (the number of times)
would be read from memory instead of being used as immediate.
Mark every immediate operand as such to avoid this problem.
Cc: stable@vger.kernel.org
Fixes: c44b4c6ab8
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUVd9KAAoJEL/70l94x66Dc1AH/0jdb8DsewyAuJzLKaJ/qJwK
9JMqglpDQ+Sm0f2puPyJkR8NQd2AMPK7J5aJjWAl/XxJjsDcn+TQur20okzUDXLJ
21sIbqo92hCgpSNs+RHLHlj7/iMQVYnMFh7bp6JcvzmhpN8F/D793BT+oOxdjMRg
PLCQ794ugGhFboesDkV822VWgtQ26yG2aQDWbYgL9r5xPp5OpbzSiq85KopSEfS0
K+PPntI8yNI+EvOC9ta0FfEOMMfQoLDds+V0FXiEIRx43MV8bwAXpWzsB8ibd1F6
eY+cVvSPzWgDSCVLn3gfYkrRl3sWGdvyfxTe/cz507ZfXcuT2uHJhtbpH2KCGto=
=FJ6/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A small set of x86 fixes. The most serious is an SRCU lockdep fix.
A bit late - needed some time to test the SRCU fix, which only came in
on Friday"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: defer load of APIC access page address during reset
KVM: nVMX: Disable preemption while reading from shadow VMCS
KVM: x86: Fix far-jump to non-canonical check
KVM: emulator: fix execution close to the segment limit
KVM: emulator: fix error code for __linearize
