By default autoenumeration is enabled on QCom SoundWire controller
which means the core should not be dealing with device 0 w.r.t enumeration.
During Enumeration if SoundWire core sees status[0] as SDW_SLAVE_ATTACHED and
start programming the device id, however reading DEVID registers return zeros
which does not match to any of the slaves in the list and the core attempts
to park this device to Group 13. This results in adding SoundWire device
with enumeration address 0:0:0:0
Fix this by not passing device 0 status to SoundWire core.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220916135352.19114-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The buf passed in struct sdw_msg must only be written for a READ,
in that case the RDATA part of the response is the data value of the
register.
For a write command there is no RDATA, and buf should be assumed to
be const and unmodifable. The original caller should not expect its data
buffer to be corrupted by an sdw_nwrite().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220916103505.1562210-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Only exit sdw_handle_slave_status() right after calling
sdw_program_device_num() if it actually programmed an ID into at
least one device.
sdw_handle_slave_status() should protect itself against phantom
device #0 ATTACHED indications. In that case there is no actual
device still on #0. The early exit relies on there being a status
change to ATTACHED on the reprogrammed device to trigger another
call to sdw_handle_slave_status() which will then handle the status
of all peripherals. If no device was actually programmed with an
ID there won't be a new ATTACHED indication. This can lead to the
status of other peripherals not being handled.
The status passed to sdw_handle_slave_status() is obviously always
from a point of time in the past, and may indicate accumulated
unhandled events (depending how the bus manager operates). It's
possible that a device ID is reprogrammed but the last PING status
captured state just before that, when it was still reporting on
ID #0. Then sdw_handle_slave_status() is called with this PING info,
just before a new PING status is available showing it now on its new
ID. So sdw_handle_slave_status() will receive a phantom report of a
device on #0, but it will not find one.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-6-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The correct way to handle interrupts is to clear the bits we
are about to handle _before_ handling them. Thus if the condition
then re-asserts during the handling we won't lose it.
This patch changes cdns_update_slave_status_work() to do this.
The previous code cleared the interrupts after handling them.
The problem with this is that when handling enumeration of devices
the ATTACH statuses can be accidentally cleared and so some or all
of the devices never complete their enumeration.
Thus we can have a situation like this:
- one or more devices are reverting to ID #0
- accumulated status bits indicate some devices attached and some
on ID #0. (Remember: status bits are sticky until they are handled)
- Because of device on #0 sdw_handle_slave_status() programs the
device ID and exits without handling the other status, expecting
to get an ATTACHED from this reprogrammed device.
- The device immediately starts reporting ATTACHED in PINGs, which
will assert its CDNS_MCP_SLAVE_INTSTAT_ATTACHED bit.
- cdns_update_slave_status_work() clears INTSTAT0/1. If the initial
status had CDNS_MCP_SLAVE_INTSTAT_ATTACHED bit set it will be
cleared.
- The ATTACHED change for the device has now been lost.
- cdns_update_slave_status_work() clears CDNS_MCP_INT_SLAVE_MASK so
if the new ATTACHED state had set it, it will be cleared without
ever having been handled.
Unless there is some other state change from another device to cause
a new interrupt, the ATTACHED state of the reprogrammed device will
never cause an interrupt so its enumeration will not be completed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-5-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Don't re-enumerate a peripheral on #0 until we have seen and
handled an UNATTACHED notification for that peripheral.
Without this, it is possible for the UNATTACHED status to be missed
and so the slave->status remains at ATTACHED. If slave->status never
changes to UNATTACHED the child driver will never be notified of the
UNATTACH, and the code in sdw_handle_slave_status() will skip the
second part of enumeration because the slave->status has not changed.
This scenario can happen because PINGs are handled in a workqueue
function which is working from a snapshot of an old PING, and there
is no guarantee when this function will run.
A peripheral could report attached in the PING being handled by
sdw_handle_slave_status(), but has since reverted to device #0 and is
then found in the loop in sdw_program_device_num(). Previously the
code would not have updated slave->status to UNATTACHED because it had
not yet handled a PING where that peripheral had UNATTACHED.
This situation happens fairly frequently with multiple peripherals on
a bus that are intentionally reset (for example after downloading
firmware).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-4-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Ensure that if sdw_handle_slave_status() sees a peripheral
has dropped off the bus it reports it to the client driver.
If there are any devices reporting on address 0 it bails out
after programming the device IDs. So it never reaches the second
loop that calls sdw_update_slave_status().
If the missing device is one that is now showing as unenumerated
it has been given a device ID so will report as attached next
time sdw_handle_slave_status() runs.
With the previous code the client driver would only see another
ATTACHED notification because the UNATTACHED state was lost when
sdw_handle_slave_status() bailed out after programming the
device ID.
This shows up most when the peripheral has to be reset after
downloading updated firmware and there are multiple of these
peripherals on the bus. They will all return to unenumerated state
after the reset, and then there is a mix of unattached, attached
and unenumerated PING states from the peripherals, as each is reset
and they reboot.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-3-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The cadence IP explicitly reports slave status changes with bits for
each possible change. The function cdns_update_slave_status() attempts
to translate this into the current status of each of the slaves.
However when there are multiple peripherals on a bus any slave that did
not have a status change when the work function ran would not have it's
status updated - the array is initialised to a value that equates to
UNATTACHED and this can cause spurious reports that slaves had dropped
off the bus.
In the case where a slave has no status change or has multiple status
changes the value from the last PING command is used.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-2-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We removed PDM support a long time ago but kept the definitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch updates device status array range from 11 to 12 as we will
be reading status from device number 0 to device number 11 inclusive.
Without this patch we can potentially access status array out of range
during auto-enumeration.
Fixes: aa1262ca66 ("soundwire: qcom: Check device status before reading devid")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220708104747.8722-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The allowed values for SoundWire device numbers are between 1 and 11
(inclusive). HDaudio/iDISP codecs typically use SDI values 0..3
(inclusive). To allow for a unique peripheral SDI/dev_number across
HDaudio and SoundWire buses, we set the minimum base to 4. This still
allows for 8 SoundWire peripherals in the system, currently more than
needed in actual products.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823045004.2670658-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SoundWire specification allows the device number to be allocated
at will. When a system includes multiple SoundWire links, the device
number scope is limited to the link to which the device is attached.
However, for integration/debug it can be convenient to have a unique
device number across the system. This patch adds a 'dev_num_ida_min'
field at the bus level, which when set will be used to allocate an
IDA.
The allocation happens when a hardware device reports as ATTACHED. If
any error happens during the enumeration, the allocated IDA is not
freed - the device number will be reused if/when the device re-joins
the bus. The IDA is only freed when the Linux device is unregistered.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823045004.2670658-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To avoid confusions with follow-up patches using a IDA mechanism for
peripheral 'device number' allocation, rename sdw_ida as sdw_bus_ida.
Pure rename, no functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823045004.2670658-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823050158.2671245-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823050158.2671245-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DSDT for this device has a number of problems:
a) it lists rt711 on link0 and link1, but link1 is disabled
b) the rt711 entry on link0 uses the wrong v2 instead of v3 (SDCA)
c) the rt1316 amplifier on link3 is not listed.
Add a remapping table to work-around these BIOS shenanigans.
BugLink: https://github.com/thesofproject/sof/issues/5955
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823030919.2346629-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The capabilities enabled for multi-link are required as part of the
programming sequences, even when a stream uses a single link we still
use the syncArm/syncGo sequences. Therefore the TODO is no longer
necessary.
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Link: https://lore.kernel.org/r/20220817074859.4759-1-khalid.masum.92@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update error prints to debug prints to avoid redundant logging in kernel
boot time, as these prints are informative prints in irq handler.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1657724067-19004-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This helper provides an optional delay parameter to wait for devices
to resync in case of errors, and checks that devices are indeed
attached on the bus.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220714011043.46059-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a
bunch of new drivers (as usual), while there have been some
significant (but almost invisible) improvements in ALSA core
side, too. Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user
won't notice, but on the devices with tons of control elements,
it can be visibly faster
- Support for input validation for controls; this will harden
for badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer
in situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some
board integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)
-----BEGIN PGP SIGNATURE-----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=1n0/
-----END PGP SIGNATURE-----
Merge tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a bunch of
new drivers (as usual), while there have been some significant (but
almost invisible) improvements in ALSA core side, too.
Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user won't
notice, but on the devices with tons of control elements, it can be
visibly faster
- Support for input validation for controls; this will harden for
badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer in
situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some board
integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)"
* tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits)
ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
ALSA: line6: Replace sprintf() with sysfs_emit()
ALSA: hda: Replace sprintf() with sysfs_emit()
ALSA: pcm: Replace sprintf() with sysfs_emit()
ALSA: core: Replace scnprintf() with sysfs_emit()
ALSA: control-led: Replace sprintf() with sysfs_emit()
ALSA: aoa: Replace sprintf() with sysfs_emit()
ALSA: ac97: Replace sprintf() with sysfs_emit()
ALSA: hda/realtek: Add quirk for Clevo NV45PZ
ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7
ALSA: control: Use deferred fasync helper
ALSA: pcm: Use deferred fasync helper
ALSA: timer: Use deferred fasync helper
ALSA: core: Add async signal helpers
ASoC: q6asm: use kcalloc() instead of kzalloc()
ACPI: scan: Add CLSA0101 Laptop Support
ALSA: hda: cs35l41: Support CLSA0101
ALSA: hda: cs35l41: Use the CS35L41 HDA internal define
ASoC: dt-bindings: use spi-peripheral-props.yaml
ASoC: codecs: va-macro: use fsgen as clock
...
Here is the large set of char and misc and other driver subsystem
changes for 6.0-rc1.
Highlights include:
- large set of IIO driver updates, additions, and cleanups
- new habanalabs device support added (loads of register maps
much like GPUs have)
- soundwire driver updates
- phy driver updates
- slimbus driver updates
- tiny virt driver fixes and updates
- misc driver fixes and updates
- interconnect driver updates
- hwtracing driver updates
- fpga driver updates
- extcon driver updates
- firmware driver updates
- counter driver update
- mhi driver fixes and updates
- binder driver fixes and updates
- speakup driver fixes
Full details are in the long shortlog contents.
All of these have been in linux-next for a while without any reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYup9QQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylBKQCfaSuzl9ZP9dTvAw2FPp14oRqXnpoAnicvWAoq
1vU9Vtq2c73uBVLdZm4m
=AwP3
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
changes for 6.0-rc1.
Highlights include:
- large set of IIO driver updates, additions, and cleanups
- new habanalabs device support added (loads of register maps much
like GPUs have)
- soundwire driver updates
- phy driver updates
- slimbus driver updates
- tiny virt driver fixes and updates
- misc driver fixes and updates
- interconnect driver updates
- hwtracing driver updates
- fpga driver updates
- extcon driver updates
- firmware driver updates
- counter driver update
- mhi driver fixes and updates
- binder driver fixes and updates
- speakup driver fixes
All of these have been in linux-next for a while without any reported
problems"
* tag 'char-misc-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (634 commits)
drivers: lkdtm: fix clang -Wformat warning
char: remove VR41XX related char driver
misc: Mark MICROCODE_MINOR unused
spmi: trace: fix stack-out-of-bound access in SPMI tracing functions
dt-bindings: iio: adc: Add compatible for MT8188
iio: light: isl29028: Fix the warning in isl29028_remove()
iio: accel: sca3300: Extend the trigger buffer from 16 to 32 bytes
iio: fix iio_format_avail_range() printing for none IIO_VAL_INT
iio: adc: max1027: unlock on error path in max1027_read_single_value()
iio: proximity: sx9324: add empty line in front of bullet list
iio: magnetometer: hmc5843: Remove duplicate 'the'
iio: magn: yas530: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: magnetometer: ak8974: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: veml6030: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4035: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4000: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: tsl2591: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: tsl2583: Use DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
iio: light: isl29028: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: gp2ap002: Switch to DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
...
When a pipeline is split into FE and BE parts, the BE pipeline may need to
be triggered separately in the BE trigger op. So add the trigger callback
in the link_res ops that will be invoked during BE DAI trigger.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220708061312.25878-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable software clock gating flag in private data for SC7280
based platforms, which are soundwire 1.6.0 version based.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[vkoul: fix patch subystem tag]
Link: https://lore.kernel.org/r/1656659827-27450-3-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As per hardware datasheet its recommended that we check the device
status before reading devid assigned by auto-enumeration.
Without this patch we see SoundWire devices with invalid enumeration
addresses on the bus.
Cc: stable@vger.kernel.org
Fixes: a6e6581942 ("soundwire: qcom: add auto enumeration support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220706095644.5852-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Validate software clock gating required or not and do software
clock gating on hclk if soundwire is operational and keep it
running by adding flag in private data structure.
This is to avoid conflict between older architectures,
where software clock gating is not required and on latest
architectures, where software clock gating is mandatory.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/1656659827-27450-2-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for controlling soundwire audio CGCR interface using clock
framework to make hclk ungating with software. As per new hardware
changes, software has to always ungate hclk if soundwire is operational
and keep it running. This requirement is for latest LPASS chipsets for
RX, TX and WSA path to work.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Link: https://lore.kernel.org/r/1652877755-25120-1-git-send-email-quic_srivasam@quicinc.com
[vkoul: change patch subsystem tag]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During the card registration, transactions on the SoundWire bus can be
initiated. If the ALSA card is registered after the bus suspends,
timeouts can be seen while reading/writing codec registers. This is
extremely easy to reproduce in driver bind/unbind tests.
In an initial experiment, the ASoC soc-component.c code was modified
to initiate a pm_runtime resume on a component probe. The results
showed this was too invasive. Instead this patch suggests resuming the
SoundWire component only.
Because of the parent-child hierarchy enforced by the pm_runtime
framework, it can be argued that the codec component probe should be
enough to resume all necessary devices, and indeed the same resume
will be applied to SoundWire codecs used on Intel platforms.
Calling pm_runtime_resume() on both the Intel and codec sides has the
benefit of resuming the bus without assuming any order during the card
registration. The first component on a dailink to be probed will
resume the bus. In addition, if a codec driver did not implement this
transition, the Intel component would still resume the bus and avoid
timeouts on card registration.
BugLink: https://github.com/thesofproject/linux/issues/3651
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220621225641.221170-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the SoundWire probe, we store a pointer from the driver ops into
the 'slave' structure. This can lead to kernel oopses when unbinding
codec drivers, e.g. with the following sequence to remove machine
driver and codec driver.
/sbin/modprobe -r snd_soc_sof_sdw
/sbin/modprobe -r snd_soc_rt711
The full details can be found in the BugLink below, for reference the
two following examples show different cases of driver ops/callbacks
being invoked after the driver .remove().
kernel: BUG: kernel NULL pointer dereference, address: 0000000000000150
kernel: Workqueue: events cdns_update_slave_status_work [soundwire_cadence]
kernel: RIP: 0010:mutex_lock+0x19/0x30
kernel: Call Trace:
kernel: ? sdw_handle_slave_status+0x426/0xe00 [soundwire_bus 94ff184bf398570c3f8ff7efe9e32529f532e4ae]
kernel: ? newidle_balance+0x26a/0x400
kernel: ? cdns_update_slave_status_work+0x1e9/0x200 [soundwire_cadence 1bcf98eebe5ba9833cd433323769ac923c9c6f82]
kernel: BUG: unable to handle page fault for address: ffffffffc07654c8
kernel: Workqueue: pm pm_runtime_work
kernel: RIP: 0010:sdw_bus_prep_clk_stop+0x6f/0x160 [soundwire_bus]
kernel: Call Trace:
kernel: <TASK>
kernel: sdw_cdns_clock_stop+0xb5/0x1b0 [soundwire_cadence 1bcf98eebe5ba9833cd433323769ac923c9c6f82]
kernel: intel_suspend_runtime+0x5f/0x120 [soundwire_intel aca858f7c87048d3152a4a41bb68abb9b663a1dd]
kernel: ? dpm_sysfs_remove+0x60/0x60
This was not detected earlier in Intel tests since the tests first
remove the parent PCI device and shut down the bus. The sequence
above is a corner case which keeps the bus operational but without a
driver bound.
While trying to solve this kernel oopses, it became clear that the
existing SoundWire bus does not deal well with the unbind case.
Commit 528be501b7 ("soundwire: sdw_slave: add probe_complete structure and new fields")
added a 'probed' status variable and a 'probe_complete'
struct completion. This status is however not reset on remove and
likewise the 'probe complete' is not re-initialized, so the
bind/unbind/bind test cases would fail. The timeout used before the
'update_status' callback was also a bad idea in hindsight, there
should really be no timing assumption as to if and when a driver is
bound to a device.
An initial draft was based on device_lock() and device_unlock() was
tested. This proved too complicated, with deadlocks created during the
suspend-resume sequences, which also use the same device_lock/unlock()
as the bind/unbind sequences. On a CometLake device, a bad DSDT/BIOS
caused spurious resumes and the use of device_lock() caused hangs
during suspend. After multiple weeks or testing and painful
reverse-engineering of deadlocks on different devices, we looked for
alternatives that did not interfere with the device core.
A bus notifier was used successfully to keep track of DRIVER_BOUND and
DRIVER_UNBIND events. This solved the bind-unbind-bind case in tests,
but it can still be defeated with a theoretical corner case where the
memory is freed by a .remove while the callback is in use. The
notifier only helps make sure the driver callbacks are valid, but not
that the memory allocated in probe remains valid while the callbacks
are invoked.
This patch suggests the introduction of a new 'sdw_dev_lock' mutex
protecting probe/remove and all driver callbacks. Since this mutex is
'local' to SoundWire only, it does not interfere with existing locks
and does not create deadlocks. In addition, this patch removes the
'probe_complete' completion, instead we directly invoke the
'update_status' from the probe routine. That removes any sort of
timing dependency and a much better support for the device/driver
model, the driver could be bound before the bus started, or eons after
the bus started and the hardware would be properly initialized in all
cases.
BugLink: https://github.com/thesofproject/linux/issues/3531
Fixes: 56d4fe31af ("soundwire: Add MIPI DisCo property helpers")
Fixes: 528be501b7 ("soundwire: sdw_slave: add probe_complete structure and new fields")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220621225641.221170-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The bus sdw_drv_remove() and sdw_drv_shutdown() helpers are used
conditionally, if the driver provides these routines.
These helpers already test if the driver provides a .remove or
.shutdown callback, so there's no harm in invoking the
sdw_drv_remove() and sdw_drv_shutdown() unconditionally.
In addition, the current code is imbalanced with
dev_pm_domain_attach() called from sdw_drv_probe(), but
dev_pm_domain_detach() called from sdw_drv_remove() only if the driver
provides a .remove callback.
Fixes: 9251345dca ("soundwire: Add SoundWire bus type")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610015105.25987-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Change the legacy DAI naming flag from opting in to the new scheme
(non_legacy_dai_naming), to opting out of it (legacy_dai_naming).
This driver appears to be on the CPU side of the DAI link and
currently uses the legacy naming, so add the new flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220623125250.2355471-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of walking the list of children of an ACPI device directly,
use acpi_dev_for_each_child() to carry out an action for all of
the given ACPI device's children.
This will help to eliminate the children list head from struct
acpi_device as it is redundant and it is used in questionable ways
in some places (in particular, locking is needed for walking the
list pointed to it safely, but it is often missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Add support for controlling soundwire audio CGCR interface using clock
framework to make hclk ungating with software. As per new hardware
changes, software has to always ungate hclk if soundwire is operational
and keep it running. This requirement is for latest LPASS chipsets for
RX, TX and WSA path to work.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Link: https://lore.kernel.org/r/1652877755-25120-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently timeout for autoenumeration during probe and bus reset is set to
2 secs which is really a big value. This can have an adverse effect on
boot time if the slave device is not ready/reset.
This was the case with wcd938x which was not reset yet but we spent 2
secs waiting in the soundwire controller probe. Reduce this time to
1/10 of Hz which should be good enough time to finish autoenumeration
if any slaves are available on the bus.
Reported-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220506084705.18525-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use pm_runtime_resume_and_get() to replace the pm_runtime_get_sync() and
pm_runtime_put_noidle() pattern.
No functional changes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220426235623.4253-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use pm_runtime_resume_and_get() to replace the pm_runtime_get_sync() and
pm_runtime_put_noidle() pattern.
No functional changes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220426235623.4253-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use pm_runtime_resume_and_get() to replace the pm_runtime_get_sync() and
pm_runtime_put_noidle() pattern.
No functional changes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220426235623.4253-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In typical use cases, the peripheral becomes pm_runtime active as a
result of the ALSA/ASoC framework starting up a DAI. The parent/child
hierarchy guarantees that the manager device will be fully resumed
beforehand.
There is however a corner case where the manager device may become
pm_runtime active, but without ALSA/ASoC requesting any functionality
from the peripherals. In this case, the hardware peripheral device
will report as ATTACHED and its initialization routine will be
executed. If this initialization routine initiates any sort of
deferred processing, there is a possibility that the manager could
suspend without the peripheral suspend sequence being invoked: from
the pm_runtime framework perspective, the peripheral is *already*
suspended.
To avoid such disconnects between hardware state and pm_runtime state,
this patch adds an asynchronous pm_request_resume() upon successful
attach/initialization which will result in the proper resume/suspend
sequence to be followed on the peripheral side.
BugLink: https://github.com/thesofproject/linux/issues/3459
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220420023241.14335-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the manager device is pm_runtime resumed, we see a series of
spurious wakes and attempts to resume the same device:
soundwire_intel.link.0: intel_resume_runtime: start
soundwire_intel.link.0: intel_link_power_up: powering up all links
soundwire_intel.link.0: intel_link_power_up: first link up, programming SYNCPRD
soundwire_intel.link.0: intel_shim_wake: WAKEEN disabled for link 0
soundwire_intel.link.0: intel_link_process_wakeen_event: pm_request_resume start
soundwire_intel.link.0: intel_link_process_wakeen_event: pm_request_resume done
soundwire_intel.link.0: intel_shim_wake: WAKEEN disabled for link 0
soundwire_intel.link.0: intel_link_process_wakeen_event: pm_request_resume start
soundwire_intel.link.0: intel_link_process_wakeen_event: pm_request_resume done
This sequence does not break anything but is totally unnecessary.
Currently the wakes are only disabled after the peripheral generates a
wake, e.g. for jack detection.
If the resume is initiated by the host drivers as a result of
userspace actions (play/record typically), we need to disable wake
detection as well. Doing so prevents the spurious wakes and calls to
pm_request_resume().
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220420023241.14335-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit e38f9ff63e ("ACPI: scan: Do not add device IDs from _CID if _HID is not valid")
exposes a race condition on a TGL RVP device leading to a timeout.
The detailed analysis shows the RT711 codec driver scheduling a jack
detection workqueue while attaching during a spurious pm_runtime
resume, and the work function happens to be scheduled after the
manager device is suspended.
The direct link between this ACPI patch and a spurious pm_runtime
resume is not obvious; the most likely explanation is that a change in
the ACPI device linked list management modifies the order in which the
pm_runtime device status is checked and exposes a race condition that
was probably present for a very long time, but was not identified.
We already have a check in the .prepare stage, where we will resume to
full power from specific clock-stop modes. In all other cases, we
don't need to resume to full power by default. Adding the
SMART_SUSPEND flag prevents the spurious resume from happening.
BugLink: https://github.com/thesofproject/linux/issues/3459
Fixes: 029bfd1cd5 ("soundwire: intel: conditionally exit clock stop mode on system suspend")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220420023241.14335-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a status check after device0 attachment to solve race
conditions observed during attachment with multiple devices per link
The sequence is the following
1) deviceA attaches as device0
2) the hardware detects a device0 status change and throws an
interrupt.
3) the interrupt handler schedules the work function
4) the workqueue starts, we read the status
slave0 = cdns_readl(cdns, CDNS_MCP_SLAVE_INTSTAT0);
slave1 = cdns_readl(cdns, CDNS_MCP_SLAVE_INTSTAT1);
we deal with the status change and program deviceA device number to a
non-zero value.
5) deviceB attaches as device0, the device0 status seen by the
hardware does not change.
6) we clear the CDNS_MCP_SLAVE_INTSTAT0/1 registers -> we will never detect
deviceB!
This patch suggest re-checking in a loop the device0 status with a
PING frame, i.e. using the real device0 status instead of information
on status changes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220420023039.14144-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update compatible string and master data information in soundwire driver
to support v1.6.0 in lpass sc7280 based platform.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1646316128-21082-2-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220307074039.117488-1-wangwensheng4@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The logical AND && is supposed to be bitwise AND & so it will sometimes
print "connected" instead of "disconnected".
Fixes: 74e79da9fd ("soundwire: qcom: add runtime pm support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220307125814.GD16710@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
HP changed the DMI identification for 2022 devices:
Product Name: HP Spectre x360 Conv 13-ap0001na
Product Name: 8709
This patch relaxes the DMI_MATCH criterion to work with all versions of this product.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Anthony I Gilea <i@cpp.in>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304204532.54675-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
swrm_runtime_resume() would not be defined when CONFIG_PM=n
This causes below build failure
drivers/soundwire/qcom.c:1460:12: error: 'swrm_runtime_resume' defined
but not used [-Werror=unused-function]
Mark the resume swrm_runtime_resume() with __maybe_unused attribute.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220303110321.23666-1-srinivas.kandagatla@linaro.org
[redo commit title and log]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The qcom_swrm_data structures is only required for setting soundwire
params, so make the qcom_swrm_data structure const to allow the compiler
to put it in read-only memory and avoid unintentional modifications.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Link: https://lore.kernel.org/r/1646224982-3361-3-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some of the Qualcomm SoundWire Controller instances like the ones that are
connected to RX path along with Headset connections support Waking up
Controller from Low power clock stop state using SoundWire In-band interrupt.
SoundWire Slave on the bus would initiate this by pulling the data line high,
while the clock is stopped.
Add support to this wake up interrupt.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220228172528.3489-4-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to runtime PM using SoundWire clock stop Mode0 on supported
controller instances and soft reset on instances that do not support
clock stop.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220228172528.3489-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The stream management currently flags an 'inconsistent state' error
when a change is requested multiple times. This was added on purpose
to identify programming mistakes.
In hindsight, there was no real reason to fail if the logic at the
ASoC-DPCM level invokes the same callback multiple times. It's
perfectly acceptable to just return and not flag an error when there
is nothing to do. The main concern with the state management is to
trap errors such as trying to enable a stream that was not prepared
first.
This patch suggests allowing the stream functions to be idempotent,
i.e. they can be called multiple times.
Note that the prepare case was already handling multiple calls, this
was added in commit c32464c939 ("soundwire: stream: only prepare
stream when it is configured.")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-20-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sdw_stream_add_slave/master() functions are called from the
.hw_params stage. We need to make sure the functions can be called
multiple times.
In this version, we assume that only 'audio' parameters provide in the
hw_params() can change. If the number of ports could change
dynamically depending on the stream configuration (number of channels,
etc), we would need to free-up all the stream resources and reallocate
them.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-19-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Before we split the alloc and config steps, we need a helper to find
the Slave runtime for a stream. The helper is based on the search loop
in sdw_slave_rt_free(), which can now be simplified.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-18-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Separate alloc and config parts so that follow-up patches can allow
for multiple calls to sdw_stream_add_slave/master. This is a feature
from the ALSA/ASoC frameworks which is not supported today.
This is an invasive patch which modifies the error handling flow, with
cleanups only done when an allocation fails. Configuration failures
only return an error code.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-17-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify sdw_stream_add_slave() by moving the linked list management
inside of the sdw_slave_alloc_rt_free() helper, this also makes the
alloc/free helpers more symmetrical.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-16-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The naming is rather inconsistent, use the sdw_<object>_<action>
convention, and move the free routine after alloc/config.
No functionality change beyond rename/move.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-15-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Group all exported functions prior to split of add in alloc/config
stages necessary for support of multiple calls to hw_params() by
ALSA/ASoC core.
Pure code move, no functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-14-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Split the two parts so that we can do multiple configurations during
ALSA/ASoC hw_params stage. Also follow existing convention
sdw_<object>_<action> used at lower level.
No functionality change here.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-13-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Code move before splitting the function in two.
No functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-12-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Split the two parts so that we can do multiple configurations during
ALSA/ASoC hw_params stage. Also follow existing convention
sdw_<object>_<action> used at lower level.
No functionality change here.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Only do the allocation in that function, and move check for allocation
in the caller. This will it easier to split allocation and
configuration.
No functionality change in this patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
re-group all the helpers in one location with a code move. For
consistency the 'slave' helpers are placed before the 'master'
helpers.
Also remove unused arguments and rename the 'release' function to
'free' for consistency.
No functional change in this patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We can only check for Slave port ranges, the ports are not defined at
the Master level. Also move the function to the 'slave port' block.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Continue the split with two functions for master and slave, and remove
unused arguments.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Split loops before moving the allocation and configuration to separate
functions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code only has a config helper that allocates memory,
start adding alloc/config/free for ports, as a first step in the
simplification of the stream API.
This change removes a kfree() on a configuration error, this should
have not impact on existing platforms and error handling will be
revisited in follow-up patches to make sure invalid configurations
have not impact on memory allocation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pass the index directly to sdw_is_valid_port_range(), this will be
useful for further simplifications.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sdw_config_stream() only verifies the compatibility between
information provided by the Slave driver and the stream configuration.
There is no problem if we add the slave runtime to the list earlier.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The stream parameter is not used, remove before further simplifications.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011715.28204-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/3173256.44csPzL39Z@kreacher
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In rare cases, some devices seem to lose sync and never re-attach on
the bus. This seems to happen only when there are more than one device
per link, which suggests either an electrical issue, a race condition
or a state machine issue.
Add two dev_warn() messages to identify the sequence by which the
devices become UNATTACHED.
BugLink: https://github.com/thesofproject/linux/issues/3063
BugLink: https://github.com/thesofproject/linux/issues/3325
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220126011527.27930-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the large set of char, misc, and other "small" driver subsystem
changes for 5.17-rc1.
Lots of different things are in here for char/misc drivers such as:
- habanalabs driver updates
- mei driver updates
- lkdtm driver updates
- vmw_vmci driver updates
- android binder driver updates
- other small char/misc driver updates
Also smaller driver subsystems have also been updated, including:
- fpga subsystem updates
- iio subsystem updates
- soundwire subsystem updates
- extcon subsystem updates
- gnss subsystem updates
- phy subsystem updates
- coresight subsystem updates
- firmware subsystem updates
- comedi subsystem updates
- mhi subsystem updates
- speakup subsystem updates
- rapidio subsystem updates
- spmi subsystem updates
- virtual driver updates
- counter subsystem updates
Too many individual changes to summarize, the shortlog contains the full
details.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYeGNAQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoVgCg1CPjMu8/SDj3Sm3a1UMQJn9jnl8AnjQcEp3z
hMr9mISG4r6g4PvjrJBj
=9May
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char, misc, and other "small" driver
subsystem changes for 5.17-rc1.
Lots of different things are in here for char/misc drivers such as:
- habanalabs driver updates
- mei driver updates
- lkdtm driver updates
- vmw_vmci driver updates
- android binder driver updates
- other small char/misc driver updates
Also smaller driver subsystems have also been updated, including:
- fpga subsystem updates
- iio subsystem updates
- soundwire subsystem updates
- extcon subsystem updates
- gnss subsystem updates
- phy subsystem updates
- coresight subsystem updates
- firmware subsystem updates
- comedi subsystem updates
- mhi subsystem updates
- speakup subsystem updates
- rapidio subsystem updates
- spmi subsystem updates
- virtual driver updates
- counter subsystem updates
Too many individual changes to summarize, the shortlog contains the
full details.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (406 commits)
counter: 104-quad-8: Fix use-after-free by quad8_irq_handler
dt-bindings: mux: Document mux-states property
dt-bindings: ti-serdes-mux: Add defines for J721S2 SoC
counter: remove old and now unused registration API
counter: ti-eqep: Convert to new counter registration
counter: stm32-lptimer-cnt: Convert to new counter registration
counter: stm32-timer-cnt: Convert to new counter registration
counter: microchip-tcb-capture: Convert to new counter registration
counter: ftm-quaddec: Convert to new counter registration
counter: intel-qep: Convert to new counter registration
counter: interrupt-cnt: Convert to new counter registration
counter: 104-quad-8: Convert to new counter registration
counter: Update documentation for new counter registration functions
counter: Provide alternative counter registration functions
counter: stm32-timer-cnt: Convert to counter_priv() wrapper
counter: stm32-lptimer-cnt: Convert to counter_priv() wrapper
counter: ti-eqep: Convert to counter_priv() wrapper
counter: ftm-quaddec: Convert to counter_priv() wrapper
counter: intel-qep: Convert to counter_priv() wrapper
counter: microchip-tcb-capture: Convert to counter_priv() wrapper
...
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmHgHvgOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9/JBAAk1qY+2GE7a2j/dRW31rv2JxS3iMnCIdnp/Hn
c0mArt8iEDPXbgmQ2b+tnuqh5GSz073UPCorxkEdAkYisbGSzk22VnfWsNwbSEgC
p8Tqt8ma1blQWUYGzszQEN9u9BCLaMr1cO/ORZmD/f7hSq5W42Q8IYLTb1/9gdax
+pJyBg8Y52PAKURnKWzmDoasJeDoQauxZ9R0g3BgQHj8Hb3QHQonyqKxJlyFac/e
RyV7YycM2ES3Dj4u7TReRd9hdKeuzc2Wg8qYVC3x/9dzhKpvDM3Tg5ONw/58jW4x
G6tuEj5SeEKH2LRQYTOLYScz9lVUalv97PCsq5LkQrDLqrO3hT+vxQpRdBZefRIQ
+cKBd9GReRlQW9XCDrUs9ZuWtl1cyta8T3mk3WhTvjUcTlr1vd+TcyRoQvNhFNVH
LaTjD1526Yra8BxyzSe7tyHhvOIvRWwjzSfwCyYV9097wV82+rOReqHyMDhN7Djc
NbBQvoIh7v1Yo+hOYE3RUUhS5h+CJH8l43J1pWNODjXVYivYTzCOizDdJ8ktRaHE
gpQ1vAM4pW1R5mQsyIwj6G9B1bclYboVBjlE9SXCpT3vmDneIWuLUmNV89gyNW+p
96B3dL4BoCTyBtGYBtow2Es+/rX2dEWtM6pvOSHhRDoWL586Snr2lXDEbAQ9uZF9
zpq1uqs=
=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
While the hardware supports PDM streams, this capability has never
been tested or enabled on any product, so this is dead-code. Let's
remove all this.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
drivers/soundwire/intel.c:1487:10: style: Variable 'ret' is assigned a
value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HDAudio ASoC support relies on the set_tdm_slots() helper to store
the HDaudio stream tag in the tx_mask. This only works because of the
pre-existing order in soc-pcm.c, where the hw_params() is handled for
codec_dais *before* cpu_dais. When the order is reversed, the
stream_tag is used as a mask in the codec fixup functions:
/* fixup params based on TDM slot masks */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
codec_dai->tx_mask)
soc_pcm_codec_params_fixup(&codec_params,
codec_dai->tx_mask);
As a result of this confusion, the codec_params_fixup() ends-up
generating bad channel masks, depending on what stream_tag was
allocated.
We could add a flag to state that the tx_mask is really not a mask,
but it would be quite ugly to persist in overloading concepts.
Instead, this patch suggests a more generic get/set 'stream' API based
on the existing model for SoundWire. We can expand the concept to
store 'stream' opaque information that is specific to different DAI
types. In the case of HDAudio DAIs, we only need to store a stream tag
as an unsigned char pointer. The TDM rx_ and tx_masks should really
only be used to store masks.
Rename get_sdw_stream/set_sdw_stream callbacks and helpers as
get_stream/set_stream. No functionality change beyond the rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch provides both a simplification of the suspend flows and a
better balanced operation during suspend/resume transition, as part of
the transition of Sound Open Firmware (SOF) to dynamic pipelines: the
DSP resources are only enabled when required instead of enabled on
startup.
The exiting code relies on a convoluted way of dealing with suspend
signals. Since there is no .suspend DAI callback, we used the
component .suspend and marked all the component DAI dmas as
'suspended'. The information was used in the .prepare stage to
differentiate resume operations from xrun handling, and only
reinitialize SHIM registers and DMA in the former case.
While this solution has been working reliably for about 2 years, there
is a much better solution consisting in trapping the TRIGGER_SUSPEND
in the .trigger DAI ops. The DMA is still marked in the same way for
the .prepare op to run, but in addition the callbacks sent to DSP
firmware are now balanced.
Normal operation:
hw_params -> intel_params_stream
hw_free -> intel_free_stream
suspend -> intel_free_stream
prepare -> intel_params_stream
This balanced operation was not required with existing SOF firmware
relying on static pipelines instantiated at every boot. With the
on-going transition to dynamic pipelines, it's however a requirement
to keep the use count for the DAI widget balanced across all
transitions.
The component suspend is not removed but instead modified to deal with
a corner case: when a substream is PAUSED, the ALSA core does not
throw the TRIGGER_SUSPEND. This is problematic since the refcount for
all pipelines and widgets is not balanced, leading to issues on
resume. The trigger callback keeps track of the 'paused' state with a
new flag, which is tested during the component suspend called later to
release the remaining DSP resources. These resources will be
re-enabled in the .prepare step.
The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a
problem since the BE dailink is already marked as non-atomic.
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't really need to pass a substream to the callback, we only need
the direction. No functionality change, only simplification to enable
improve suspend with paused streams.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use auxiliary_get_drvdata and auxiliary_set_drvdata helpers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211221235852.323752-3-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Slave pointer is invalid after end of list iteration, using this
would result in below Memory abort.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
...
Call trace:
__dev_printk+0x34/0x7c
_dev_warn+0x6c/0x90
sdw_bus_exit_clk_stop+0x194/0x1d0
swrm_runtime_resume+0x13c/0x238
pm_generic_runtime_resume+0x2c/0x48
__rpm_callback+0x44/0x150
rpm_callback+0x6c/0x78
rpm_resume+0x314/0x558
rpm_resume+0x378/0x558
rpm_resume+0x378/0x558
__pm_runtime_resume+0x3c/0x88
Use bus->dev instead to print this error message.
Fixes: b50bb8ba36 ("soundwire: bus: handle -ENODATA errors in clock stop/start sequences")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211012101521.32087-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
link_id can be zero and if we have multiple controller instances
in a system like Qualcomm debugfs will end-up with duplicate namespace
resulting in incorrect debugfs entries.
Using bus-id and link-id combination should give a unique debugfs directory
entry and should fix below warning too.
"debugfs: Directory 'master-0' with parent 'soundwire' already present!"
Fixes: bf03473d5b ("soundwire: add debugfs support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210907105332.1257-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are a few intensive changes in ALSA core side at this time that
helped the significant code reduction. Meanwhile we keep getting new
stuff, so the total size still grows...
Anyway, the below are some highlights in this development cycle.
ALSA core:
- New helpers to manage page allocations and card object with devres
- Refactoring for memory allocation with wc-pages
- A new PCM hardware flag SNDRV_PCM_INFO_EXPLICIT_SYNC for controlling
the explicit sync of the stream control; it'll be used for ASoC SOF
and non-coherent memory in future
ASoC:
- Lots of cleanups and improvements to the Intel drivers, including
some new systems support
- New support for AMD Vangoh, CUI CMM-4030D-261, Mediatek Mt8195,
Renesas RZ/G2L Mediatek Mt8195, RealTek RT101P, Renesas RZ/G2L,
Rockchip RK3568 S/PDIF
USB-audio:
- Re-organized the quirk handling and a new option quirk_flags
- Fix for a regression in 5.14 code change for JACK
- Quirks for Sony WALKMAN, Digidesign mbox
HD-audio:
- Enhanced support for CS8409 codec
- More consistent shutdown behavior with the runtime PM
- The model option can accept the PCI or codec SSID as an alias
- Quirks for ASUS ROG, HP Spectre x360
Others:
- Lots of code reduction in legacy drivers with devres helpers
- FireWire MOTU 896HD support
-----BEGIN PGP SIGNATURE-----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=fHyJ
-----END PGP SIGNATURE-----
Merge tag 'sound-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are a few intensive changes in ALSA core side at this time that
helped with significant code reduction. Meanwhile we keep getting new
stuff, so the total size still grows...
Anyway, the below are some highlights in this development cycle.
ALSA core:
- New helpers to manage page allocations and card object with devres
- Refactoring for memory allocation with wc-pages
- A new PCM hardware flag SNDRV_PCM_INFO_EXPLICIT_SYNC for
controlling the explicit sync of the stream control; it'll be used
for ASoC SOF and non-coherent memory in future
ASoC:
- Lots of cleanups and improvements to the Intel drivers, including
some new systems support
- New support for AMD Vangoh, CUI CMM-4030D-261, Mediatek Mt8195,
Renesas RZ/G2L Mediatek Mt8195, RealTek RT101P, Renesas RZ/G2L,
Rockchip RK3568 S/PDIF
USB-audio:
- Re-organized the quirk handling and a new option quirk_flags
- Fix for a regression in 5.14 code change for JACK
- Quirks for Sony WALKMAN, Digidesign mbox
HD-audio:
- Enhanced support for CS8409 codec
- More consistent shutdown behavior with the runtime PM
- The model option can accept the PCI or codec SSID as an alias
- Quirks for ASUS ROG, HP Spectre x360
Others:
- Lots of code reduction in legacy drivers with devres helpers
- FireWire MOTU 896HD support"
* tag 'sound-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (421 commits)
ASoC: Revert PCM trigger changes
ALSA: usb-audio: Add lowlatency module option
ALSA: hda/cs8409: Initialize Codec only in init fixup.
ALSA: hda/cs8409: Ensure Type Detection is only run on startup when necessary
ALSA: usb-audio: Work around for XRUN with low latency playback
ALSA: pcm: fix divide error in snd_pcm_lib_ioctl
ASoC: soc-pcm: test refcount before triggering
ASoC: soc-pcm: protect BE dailink state changes in trigger
ASoC: wcd9335: Disable irq on slave ports in the remove function
ASoC: wcd9335: Fix a memory leak in the error handling path of the probe function
ASoC: wcd9335: Fix a double irq free in the remove function
ALSA: hda: Disable runtime resume at shutdown
ASoC: rockchip: i2s: Add support for frame inversion
ASoC: dt-bindings: rockchip: Add compatible strings for more SoCs
ASoC: rockchip: i2s: Add compatible for more SoCs
ASoC: rockchip: i2s: Make playback/capture optional
ASoC: rockchip: i2s: Fixup config for DAIFMT_DSP_A/B
ASoC: dt-bindings: rockchip: Document reset property for i2s
ASoC: rockchip: i2s: Fix regmap_ops hang
ASoC: rockchip: i2s: Improve dma data transfer efficiency
...
The duration of the hw_reset is defined as 4096 cycles. The Cadence IP
allows for an additional delay which doesn't seem necessary in
practice: the actual reset sequence duration is defined by the sync_go
mechanism, not by the IP itself.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818030130.17113-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel stress tests reported issues with the clock stop mode,
specifically when trying to do a system suspend while the link is
already pm_runtime suspended.
In this case, we need to disable the shim wake, but when the PCI
parent device is also pm_runtime suspended the SHIM registers are not
accessible.
Since this is an invalid corner case, this patch suggests a pm_runtime
resume of the entire bus to full power (parent+child devices) before
the system suspend so that the shim wake can be disabled.
Unlike the suspend operation, the .prepare callbacks are propagated
from root device to leaf devices. By adding a .prepare callback at the
SoundWire link level, we can double-check the pm_runtime status of the
device as well as its parent PCI device. When the problematic
configuration is detected, the device is pm_runtime resumed - which by
construction also resume its parent.
An additional loop is added to resume all child devices. In theory we
only need to restart the link, but doing so will also cause the
physical devices to synchronize and re-initialize, while their Linux
devices remain pm_runtime suspended. It's simpler to make sure the
codec devices are fully resumed so that we don't have to deal with
zombie states.
This additional loop could have been avoided by adding a .prepare
callback in SoundWire codec drivers. Functionally this would have been
equivalent. The rationale for implementing a loop at the link level is
only to reduce the amount of code required to deal at the codec level
with an Intel corner case - in other words keep codec drivers
independent from Intel platform-specific programming sequences.
BugLink: https://github.com/thesofproject/linux/issues/2606
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SoundWire Linux devices are created purely based on information
provided by platform firmware (e.g. ACPI DSDT table). When the kernel
finds a matching driver for the device address (_ADR), the probe will
initialize required data structures and initialize pm ops.
When the SoundWire link is started at a later point, the physical
devices will synchronize on the SoundWire frames and report their
attachment status, thereby triggering the enumeration and
initialization of device registers.
This two-step solution was a conscious design decision to allow e.g. a
driver to use sideband mechanisms to turn power rails on. This can
also allow OEMs to describe multiple platforms with the same DSDT
table, the devices that are not physically present in hardware.
The drawback of this approach is a bit of confusion, with more devices
than are actually present in hardware. This results in 'ghost'
devices, for which the driver successfully probes, but that will not
generate any traffic on the bus. suspend-resume transitions are
handled by drivers, and skipped when the devices are not physically
present.
This patch provides a work-around for a second-level of confusion in
platform firmware: some platforms only use HDaudio links, but
nevertheless expose SoundWire 'ghost' devices. This results in error
messages in the Intel driver while trying to suspend/resume these
links. The simplest solution is to add a boolean status flag to skip
all suspend/resume/wake sequences if the link was never started.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power down sequence sets the link_up flag as false outside of the
mutex_lock. This is potentially unsafe.
In additional the flow in that sequence can be improved by first
testing if the link was powered, setting the link_up flag as false and
proceeding with the power down. In case the CPA bits cannot be
cleared, we only flag an error since we cannot deal with interrupts
any longer.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
shim base and alh base are platform-dependent. Adding these two
parameters allows us to use different shim/alh base for each
platform.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210723115451.7245-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Those Intel sdw registers will be used by ASoC SOF drivers in the
following commits. So move those definitions to sdw_intel.h and it can
be visible to SOF drivers.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210723115451.7245-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When we set a source PDI, the target PDI parameters will be overridden
by the source register values. The loopback streams can be
independently enabled on each link.
While the loopback source and target can be configured before any
stream is active on each link, the loopback stream should only be
prepared/triggered when the playback stream is prepared. Otherwise all
registers might be programmed to their reset values and the loopback
will not succeed. The SoundWire bus driver currently does not allow
two streams to be triggered at the same time, so the playback will
have to be started first, and later the loopback.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For debug, it's interesting to create a loopback stream for each link
and use debugfs to set a source and target PDI. The target PDI would
need to be an RX port and use the same register configurations as the
source PDI. This capability allows e.g. for the headphone playback
stream to be snooped on the headset capture stream, or alternatively
for the addition of a dedicated loopback stream, in addition of
regular capture for that link.
This patch only adds the debugfs part, the port/PDI handling will be
handled in the next patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Mockup devices don't take part in command/control operations and their
virtual ports shall not be programmed.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All read and writes from/to SoundWire mockup devices will return
-ENODATA/Command_Ignored, this patch forces a Command_OK result to let
the bus perform the required configurations, e.g. for the Data Ports,
which will only have an effect on the Master side.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This change is needed for support of mockup devices, which by
construction will not provide any answer to a bank switch, but it's
also legit for regular cases.
If for some reason a device loses sync and cannot handle a bank
switch, we should go ahead anyways. The devices can always resync
later.
The only case where the error flow should be used is when there is a
Command_Aborted composite answer from SoundWire devices.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Cadence IP exposes a small number of self-clearing bits in
the MCP_CONTROL and MCP_CONFIG_UPDATE registers.
We currently do not check that those bits are indeed cleared,
e.g. during resume operations. That could lead to resuming peripheral
devices too early.
In addition, if we happen to read these registers, update one of the
fields and write the register back, we may be writing stale data that
might have been cleared in hardware. These sort of race conditions
could lead to e.g. doing a hw_reset twice or stopping a clock that
just restarted. There is no clear way of avoiding these potential race
conditions other than making sure that these registers fields are
cleared before any read-modify-write sequence. If we detect this sort
of errors, we only log them since there is no clear recovery
possible. The only way out is likely to restart the IP with a
suspend/resume cycle.
Note that the checks are performed before updating the registers, as
well as after the Intel 'sync go' sequence in multi-link mode. That
should cover both the start and end of suspend/resume hardware
configurations. The Multi-Master mode gates the configuration updates
until the 'sync go' signal is asserted, so we only check on init and
after the end of the 'sync go' sequence.
The duration of the usleep_range() was defined by the GSYNC frequency
used in multi-master mode. With a 4kHz frequency, any configuration
change might be deferred by up to 250us. Extending the range to
1000-1500us should guarantee that the configuration change is
completed without any significant impact on the overall resume
time.
Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714051349.13064-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The same quirk is used for LAPBC510 and LAPBC710 skews who use the
same audio design.
These devices have the same BIOS issues inherited from the Intel
reference, add the same _ADR remap previously used on HP devices.
BugLink: https://github.com/thesofproject/linux/issues/3049
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210719233248.557923-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ret is not used in the interrupt handler, it is just returned without
any condition or change.
We can return the IRQ_HANDLED directly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714015555.17685-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We've added quite a few filters to avoid throwing errors if a Device
does not respond to commands during the clock stop sequences, but we
missed one.
This will lead to an isolated message
[ 6115.294412] soundwire sdw-master-1: SDW_SCP_STAT bread failed:-61
The callers already filter this error code, so there's no point in
keeping it at the lower level.
Since this is a recoverable error, make this dev_err() conditional and
only log cases with Command Failed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714014209.17357-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sparse throws the following type of warnings:
drivers/soundwire/dmi-quirks.c:25:17: error: constant
0x000010025D070100 is so big it is long
Let's add the 'ull' suffix to make this go away and find real issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714013027.17022-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
Updates for v5.14-rc1 are:
- Core has odd updates including improving clock stop codes, write api,
handling ENODATA etc
- Drivers has Big move of Intel driver to be aux dev and minor updates
to Intel/cadence driver
-----BEGIN PGP SIGNATURE-----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=JGCd
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire updates for 5.14-rc1
Updates for v5.14-rc1 are:
- Core has odd updates including improving clock stop codes, write api,
handling ENODATA etc
- Drivers has Big move of Intel driver to be aux dev and minor updates
to Intel/cadence driver
* tag 'soundwire-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: Fix test for DP prepare complete
soundwire: bus: Make sdw_nwrite() data pointer argument const
soundwire: intel: move to auxiliary bus
soundwire: cadence: remove the repeated declaration
soundwire: dmi-quirks: remove duplicate initialization
soundwire: cadence_master: always set CMD_ACCEPT
soundwire: bus: add missing \n in dynamic debug
soundwire: bus: handle -ENODATA errors in clock stop/start sequences
soundwire: add missing kernel-doc description
soundwire: bus: only use CLOCK_STOP_MODE0 and fix confusions
soundwire: bandwidth allocation: improve error messages
soundwire/ASoC: add leading zeroes in peripheral device name
We currently export sdw_read() and sdw_write() but the sdw_update()
and sdw_update_no_pm() are currently available only to the bus
code. This was missed in an earlier contribution.
Export both functions so that codec drivers can perform
read-modify-write operations without duplicating the code.
Fixes: b04c975e65 ('soundwire: bus: use sdw_update_no_pm when initializing a device')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210614180815.153711-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In sdw_prep_deprep_slave_ports(), after the wait_for_completion()
the DP prepare status register is read. If this indicates that the
port is now prepared, the code should continue with the port setup.
It is irrelevant whether the wait_for_completion() timed out if the
port is now ready.
The previous implementation would always fail if the
wait_for_completion() timed out, even if the port was reporting
successful prepare.
This patch also fixes a minor bug where the return from sdw_read()
was not checked for error - any error code with LSBits clear could
be misinterpreted as a successful port prepare.
Fixes: 79df15b7d3 ("soundwire: Add helpers for ports operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210618144745.30629-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Idiomatically, write functions should take const pointers to the
data buffer, as they don't change the data. They are also likely
to be called from functions that receive a const data pointer.
Internally the pointer is passed to function/structs shared with
the read functions, requiring a cast, but this is an implementation
detail that should be hidden by the public API.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210616145901.29402-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the auxiliary_bus exists, there's no reason to use platform
devices as children of a PCI device any longer.
This patch refactors the code by extending a basic auxiliary device
with Intel link-specific structures that need to be passed between
controller and link levels. This refactoring is much cleaner with no
need for cross-pointers between device and link structures.
Note that the auxiliary bus API has separate init and add steps, which
requires more attention in the error unwinding paths. The main loop
needs to deal with kfree() and auxiliary_device_uninit() for the
current iteration before jumping to the common label which releases
everything allocated in prior iterations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210511052132.28150-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Support to "qcom,ports-block-pack-mode" was added at later stages
to support a variant of Qualcomm SoundWire controllers available
on Apps processor. However the older versions of the SoundWire
controller which are embedded in WCD Codecs do not need this property.
So returning on error for those cases will break boards like DragonBoard
DB845c and Lenovo Yoga C630.
This patch fixes error handling on this property considering older usecases.
Fixes: a5943e4fb1 ("soundwire: qcom: check of_property_read status")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20210504125909.16108-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Cadence IP can be configured in two different ways to deal with
CMD_IGNORED replies to broadcast commands. The CMD_ACCEPT bitfield
controls whether the command is discarded or if the IP proceeds with
the change (typically a bank switch or clock stop command).
The existing code seems to be inconsistent:
a) For some historical reason, we set this CMD_ACCEPT bitfield during
the initialization, but we don't during a resume from a clock-stoppped
state.
b) In addition, the loop used in the clock-stop sequence is quite
racy, it's possible that a device has lost sync but it's still tagged
as ATTACHED.
c) If somehow a Device loses sync and is unable to ack a broadcast
command, we do not have an error handling mechanism anyways. The IP
should go ahead and let the Device regain sync at a later time.
Make sure the CMD_ACCEPT bit is always set.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210511025247.25339-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If a device lost sync and can no longer ACK a command, it may not be
able to enter a lower-power state but it will still be able to resync
when the clock restarts. In those cases, we want to continue with the
clock stop sequence.
This patch modifies the behavior during clock stop sequences to only
log errors unrelated to -ENODATA/Command_Ignored. The flow is also
modified so that loops continue to prepare/deprepare other devices
even when one seems to have lost sync.
When resuming the clocks, all issues are logged with a dev_warn(),
previously only some of them were checked. This is the only part that
now differs between the clock stop entry and clock stop exit
sequences: while we don't want to stop the suspend flow, we do want
information on potential issues while resuming, as they may have
ripple effects.
For consistency the log messages are also modified to be unique and
self-explanatory. Errors in sdw_slave_clk_stop_callback() were
removed, they are now handled in the caller.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210511030048.25622-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Existing devices and implementations only support the required
CLOCK_STOP_MODE0. All the code related to CLOCK_STOP_MODE1 has not
been tested and is highly questionable, with a clear confusion between
CLOCK_STOP_MODE1 and the simple clock stop state machine.
This patch removes all usages of CLOCK_STOP_MODE1 - which has no
impact on any solution - and fixes the use of the simple clock stop
state machine. The resulting code should be a lot more symmetrical and
easier to maintain.
Note that CLOCK_STOP_MODE1 is not supported in the SoundWire Device
Class specification so it's rather unlikely that we need to re-add
this mode later.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210511030048.25622-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In rare corner cases, we see an error with the log:
[ 838.297840] soundwire sdw-master-1: Compute bus params failed: -22
That's not very useful, there can be two different error conditions
with the same -EINVAL code provided to the caller.
Let's add better dev_err() messages to figure out what went wrong.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210511054945.29558-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We recently added leading zeroes in dev_dbg() messages but forgot to
do the same for the peripheral device name. Adding leading zeroes
makes it easier to read manufacturer ID and part ID, e.g.:
sdw:0:025d:0700:00
sdw:0:025d:0711:00
sdw:1:025d:0700:00
sdw:1:025d:1308:00
sdw:2:025d:0700:00
sdw:2:025d:0701:00
sdw:3:025d:0700:00
sdw:3:025d:0715:00
The use of '01x' for link_id and unique_id is intentional to show the
value range in the code, it's understood it does not actually change
the format.
To avoid problems with git bisect, the same change needs to be applied
to the Intel SoundWire machine driver, otherwise the components can't
be found and the card registration fails.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210511060137.29856-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
intel_link_probe() could return error and dev_get_drvdata() will return
null in such case. So we have to test link->cdns after
link->cdns = dev_get_drvdata(&ldev->auxdev.dev);
Otherwise, we will meet the "kernel NULL pointer dereference" error.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210406010101.11442-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Looks like return from reg_write is set but not checked.
Fix this by adding error return path.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1503591 ("UNUSED_VALUE")
Fixes: 128eaf937a ("soundwire: qcom: add support to missing transport params")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210401091502.15825-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Internally used portconfig array for storing port bandwidth
params starts from offset zero. However port zero is not really
used and we also copy the bus parameters to offset zero.
So basically we endup with a code which has to subtract 1 from port
number to get to port parameters.
This is bit confusing to the reader so, make this bit more obvious by only
copying the parameters to offset 1 instead of zero. This will avoid doing
-1 every time when we try to get port params.
Similar thing has been recently done with din/dout_port_mask.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210401092454.21299-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If we write registers very fast we can endup in a situation where some
of the writes will be dropped without any notice.
So wait for the fifo space to be available before reading/writing the
soundwire registers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210401090058.24041-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SoundWire device ports are statically mapped to Controller ports during
design. Add support to read these from SoundWire devices.
This controller uses static port map info to setup bandwidth
parameters for those ports.
A generic port allocation is not possible in this cases!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210315165650.13392-4-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
currently the internal bitmask used for allocating ports starts with offset 0.
This is bit confusing as data port numbers on Qualcomm controller are valid
from 1 to 14. So adjust this bit mask accordingly, this will also help while
adding static port map support.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210315165650.13392-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When stream config is failed, master runtime will release all
slave runtime in the slave_rt_list, but slave runtime is not
added to the list at this time. This patch frees slave runtime
in the config error path to fix the memory leak.
Fixes: 89e590535f ("soundwire: Add support for SoundWire stream management")
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Keyon Jie <yang.jie@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210331004610.12242-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We get warning of using a unsigned variable being compared to less than
zero. The comparison is correct as it checks for errors from previous
call to qcom_swrm_get_alert_slave_dev_num(), so we should use a signed
variable here.
While at it, drop the superfluous initialization as well
drivers/soundwire/qcom.c: qcom_swrm_irq_handler() warn: impossible
condition '(devnum < 0) => (0-255 < 0)'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210331155520.2987823-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Qualcomm SoundWire controller supports Auto Enumeration of the
devices within the IP. This patch enables support for this feature.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-9-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Exporting these three functions makes sense as it can be used by
other controllers like Qualcomm during auto-enumeration!
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210330144719.13284-8-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to new interrupts which includes reporting some of the
error interrupts and adding support to SLAVE pending interrupt!
This patch also changes the interrupt handler behaviour on handling
any pending interrupts by checking it before returning out of irq handler.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-7-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the existing code every soundwire register read and register write
are kinda blocked. Each of these are using a special command id that
generates interrupt after it successfully finishes. This is really
overhead, limiting and not really necessary unless we are doing
something special.
We can simply read/write the fifo that should also give exactly
what we need! This will also allow to read/write registers in
interrupt context, which was not possible with the special
command approach.
With previous approach number of interrupts generated
after enumeration are around 130:
$ cat /proc/interrupts | grep soundwire
21: 130 0 0 0 0 0 0 0 GICv3 234 Edge soundwire
after this patch they are just 3 interrupts
$ cat /proc/interrupts | grep soundwire
21: 3 0 0 0 0 0 0 0 GICv3 234 Edge soundwire
This has significantly not only reduced interrupting CPU during enumeration
but also during streaming!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-6-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Start the clock during initialization, doing this explicitly
will add more clarity when we are adding clock stop feature.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-5-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
version 1.5.1 and higher IPs of this controller required to set
continue execution on ignored command flag. This patch sets this flag.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-4-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some of the transport parameters derived from device tree
are not fully parsed by the driver.
This patch adds support to parse those missing parameters.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We sometimes see COMMAND_IGNORED responses during the clock stop
sequence. It turns out we already have information if devices are
present on a link, so we should only prepare those when they
are attached.
In addition, even when COMMAND_IGNORED are received, we should still
proceed with the clock stop. The device will not be prepared but
that's not a problem.
The only case where the clock stop will fail is if the Cadence IP
reports an error (including a timeout), or if the devices throw a
COMMAND_FAILED response.
BugLink: https://github.com/thesofproject/linux/issues/2621
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210323013707.21455-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code makes no sense, we multiply a channel number by
zero (SDW_BLK_GRP_CNT_1), and the result is used to configure the
block packing mode. Sampling grouping and channel packing are two
separate concepts in SoundWire.
In addition, the bandwidth allocation allocates a vertical slice for
each stream, which makes the use of the PER_CHANNEL packing mode
irrelevant.
Let's use the proper definition for block packing mode (PER_PORT).
This change has no functional impact though since the net result is
the same configuration of the DPN_BlockCtrl3 register, when
implemented.
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210323050701.23760-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
found flag is used to indicate SoundWire devices that are
both enumerated on the bus and available in the device list.
However this flag is not reset correctly after one iteration,
This could miss some of the devices that are enumerated on the
bus but not in device list. So reset this correctly to fix this issue!
Fixes: d52d7a1be0 ("soundwire: Add Slave status handling helpers")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210309104816.20350-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
v5.12-rc1 flags new warnings with make W=1, fix missing or broken
function descriptors.
drivers/soundwire/cadence_master.c:914: warning: expecting prototype
for To update slave status in a work since we will need to
handle(). Prototype was for cdns_update_slave_status_work() instead
drivers/soundwire/cadence_master.c:976: warning: expecting prototype
for sdw_cdns_enable_slave_interrupt(). Prototype was for
cdns_enable_slave_interrupts() instead
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210301174714.117172-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need to assign a pointer to NULL if it's only used in a
loop and assigned within that loop.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-12-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cppcheck complains about possible null pointer dereferences, but it's
more like there are unnecessary initializations before walking
through a list.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cppcheck complains:
drivers/soundwire/qcom.c:773:6: style: Variable 'ret' is assigned a
value that is never used. [unreadVariable]
ret = of_property_read_u8_array(np, "qcom,ports-block-pack-mode",
^
The return value is checked for all other cases, not sure why it was
missed here.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cppcheck complains:
drivers/soundwire/intel.c:564:15: style: Variable 'link_control' is
assigned a value that is never used. [unreadVariable]
link_control = intel_readl(shim, SDW_SHIM_LCTL);
This looks like a leftover from a previous version, remove.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cppcheck complains about two possible null pointer dereferences, but
it's more like there are unnecessary initializations before walking
through a list.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cppcheck complains about a possible null pointer dereference, but it's
more like there is an unnecessary initialization before walking
through a list.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We have multiple cases where we read/write SCP_INT registers, but the
same error message in all cases. Add a distinct error message for each
case to help debug.
Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no real reason to provide this information except for debug
sessions, hence dev_dbg() is a better fit.
Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
