LTC3815 is a Monolithic Synchronous DC/DC Step-Down Converter.
Cc: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
HTU21 is now supported by IIO, and can be instantiated as hwmon driver
using the iio-hwmon bridge. An explicit hwmon driver is no longer needed.
Cc: William Markezana <william.markezana@meas-spec.com>
Cc: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9u+p
-----END PGP SIGNATURE-----
Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
The TMP75C has a different control register layout and only supports
12-bit temperature samples (0.0625 deg C).
The continuous sample rate is ~12 Hz.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
NCT6793D is register compatible with NCT6792D.
Also move nct6775_sio_names[] closer to enum kinds to simplify
adding new chips.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch updates description of fam15h_power driver, its scope is
extended to family 16h processsors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2975 is mostly compatible to LTC2974, but supports input current
and power measurement.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm attributes have well defined names, which should be used.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add an item to the checklist when submitting a new hwmon driver: only
some I2C addresses can be probed, others should not for safety
reasons.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add hwmon driver for the Microchip TC74.
The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C address 0x37 may be used by EEPROMs, which can result in false
positives. Do not attempt to detect a chip at this address.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8620E is mostly compatible to IT7828F. Add generic support for it.
IT8620E supports up to 6 fan tachometers and 6 pwm controls.
Support for the 6th tachometer and for the additional pwm controls
are addded in separate patches.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8790E is a super-IO chip with three fan tachometers. It is mostly
compatible to IT8728F, but only supports three fan tachometers
instead of five.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest
that the upper 8 bit of the device ID reflect the chip ID and the lower
8 bit reflect the version number, modify the code to accept all chips
with ID 0x29xx.
Also add support for TS3001 and TSE2004.
Some of the datasheets for older chips are no longer available from
the IDT web site, so replace explicit links in the documentation with
a generic note.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8781F is mostly compatible to IT8782F. Major difference is that it only
supports four instead of six UART channels, and therefore does not share
the uart6 pins.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This attribute allows to configure the update interval of ina226. Although
the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can
now modify said interval by changing the averaging rate.
While we're at it - add an additional variable to ina2xx_data, which holds
the current configuration settings - this way we'll be able to restore the
configuration in case of an unexpected chip reset.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt resistance can only be set via platform_data or device tree. This
isn't suitable for devices in which the shunt resistance can change/isn't
known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP435 supports a range of I2C addresses, not just 0x4c.
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95233 is similar to LM95234, but it only supports two
instead of four external temperature sensors.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95235 is register compatible to LM95245.
Also update link to LM95245 data sheet, and drop the link to the
datasheet from the driver source to simplify code maintenance.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6792D is similar to NCT6791D. Only beep control and temperature
monitoring registers are different.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document support for NCT6102D/NCT6104D/NCT6106D and NCT6791D.
Document that NCT5573D is compatible to NCT6775F with the same chip ID.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is basically a faster lm75 with improved (11 bit) resolution.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds temperature monitoring support for F15h M60h processor.
- Add new pci device id for the relevant processor
- The functionality of REG_REPORTED_TEMPERATURE is moved to
D0F0xBC_xD820_0CA4 [Reported Temperature Control]
- So, use this to get CUR_TEMP value
- Since we need an indirect register access, protect this with
a mutex lock
- Add Kconfig, Doc entries to indicate support for this processor.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
[Guenter Roeck: Declare new mutex and function static]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver enables control of fans connected to PWM lines.
This driver uses the PWM framework, so it is compatible with all
PWM devices that provide drivers through the PWM framework.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
[Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For TI power management chip TPS40422, READ_TEMPERATURE_2 command is supported on
page 1 of the chip, but the original driver(pmbus.c) only tried to detect this command
on page 0, this will lead to a result that the temperature sensor in page 1 couldn't
be detected. This change is to isolate the tps40422 driver from pmbus.c into a solo
front-end driver.
Signed-off-by: Zhu Laiwen <richard.zhu@nsn.com>
[Guenter Roeck: Dropped unnecessary license text (fixes checkpatch warning)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
