When resuming from system sleep states the driver issues following
warning on Intel hardware:
thunderbolt 0000:07:00.0: interrupt for TX ring 0 is already enabled
The reason for this is that the commit in question did not mask the ring
interrupt on Intel hardware leaving the interrupt active. Fix this by
masking it also in Intel hardware.
Reported-by: beld zhang <beldzhang@gmail.com>
Tested-by: beld zhang <beldzhang@gmail.com>
Closes: https://lore.kernel.org/linux-usb/ZHKW5NeabmfhgLbY@debian.me/
Fixes: c4af8e3fec ("thunderbolt: Clear registers properly when auto clear isn't in use")
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the boot firmware has already established tunnels, especially ones
that have special requirements from the link such as DisplayPort, we
should not blindly enable CL states (nor change the TMU configuration).
Otherwise the existing tunnels may not work as expected.
For this reason, skip the CL state enabling when we go over the existing
topology. This will also keep the TMU settings untouched because we do
not change the TMU configuration when CL states are not enabled.
Reported-by: Koba Ko <koba.ko@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7831
Cc: stable@vger.kernel.org # v6.0+
Acked-By: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It turns out that when plugging in VGA cable through USB-C to VGA/DVI
dongle the Connection Manager handshake can take longer time, at least
on Intel Titan Ridge based docks such as Dell WD91TB. This leads to
following error in the dmesg:
thunderbolt 0000:00:0d.3: 3:10: DP tunnel activation failed, aborting
and the display stays blank (because we failed to establish the tunnel).
For this reason increase the timeout to 3s.
Reported-by: Koba Ko <koba.ko@canonical.com>
Cc: stable@vger.kernel.org
Acked-By: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both tb_xdomain_enable_paths() and tb_xdomain_disable_paths() expect -1,
not 0, if the corresponding ring is not needed. For this reason change
the driver to use correct value for the rings that are not needed.
Fixes: 180b068942 ("thunderbolt: Allow multiple DMA tunnels over a single XDomain connection")
Cc: stable@vger.kernel.org
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When `QUIRK_AUTO_CLEAR_INT` isn't set, interrupt masking should be
cleared by writing to Interrupt Mask Clear (IMR) and interrupt
status should be cleared properly at shutdown/init.
This fixes an error where interrupts are left enabled during resume
from hibernation with `CONFIG_USB4=y`.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for rings")
Cc: stable@vger.kernel.org # v6.3
Reported-by: Takashi Iwai <tiwai@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217343
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=IcG3
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.4 merge window
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Introduce usb4_port_sb_opcode_err_to_errno() helper
thunderbolt: Make use of SI units from units.h
thunderbolt: Get rid of redundant 'else'
thunderbolt: Refactor DROM reading
thunderbolt: use `tb_eeprom_get_drom_offset` to discover DROM offset
The usb4_port_sb_opcode_err_to_errno() converts from USB4 error codes
to the Linux errno space. In particular, this makes the intention
of the repeating usb4_port_retimer_read() call in the
usb4_port_retimer_nvm_authenticate_status() clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In a couple of places it seems reasonable to use MEGA intead
of explicit number. It makes code more readable and robust.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
cppcheck reports
drivers/thunderbolt/nhi.c:74:7: style: Local variable 'bit' shadows outer variable [shadowVariable]
int bit;
^
drivers/thunderbolt/nhi.c:66:6: note: Shadowed declaration
int bit = ring_interrupt_index(ring) & 31;
^
drivers/thunderbolt/nhi.c:74:7: note: Shadow variable
int bit;
^
For readablity rename the outer to interrupt_bit and the innner
to auto_clear_bit.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for ring")
Cc: stable@vger.kernel.org
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When interrupt auto clear is programmed, any read to the interrupt
status register will clear all interrupts. If two interrupts have
come in before one can be serviced then this will cause lost interrupts.
On AMD USB4 routers this has manifested in odd problems particularly
with long strings of control tranfers such as reading the DROM via bit
banging.
Instead of clearing interrupts automatically, clear the bit corresponding
to the given ring's interrupt in the ISR.
Fixes: 7a1808f82a ("thunderbolt: Handle ring interrupt by reading interrupt status register")
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Anson Tsao <anson.tsao@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
`ring_interrupt_index` doesn't change the data for `ring` so mark it as
const. This is needed by the following patch that disables interrupt
auto clear for rings.
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The NVM reading code has a series of gotos that potentially introduce
unexpected behaviors with retries if something unexpected has failed
to parse.
Refactor the code to remove the gotos and drop the retry logic.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
[mw: renamed root switch to host router, split device handling too]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The static function `tb_eeprom_get_drom_offset` has more safety guards
for the DROM offset fetching. Use this instead of just `tb_sw_read`
No intended functional changes.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When tunneling aggregated USB3 (20 Gb/s) the bandwidth values that are
programmed to the ADP_USB3_CS_2 go higher than 4096 and that does not
fit anymore to the 12-bit field. Fix this by scaling the value using
the scale field accordingly.
Fixes: 3b1d8d577c ("thunderbolt: Implement USB3 bandwidth negotiation routines")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Current Intel USB4 host routers have hardware limitation that the USB3
bandwidth cannot go higher than 16376 Mb/s. Work this around by adding a
new quirk that limits the bandwidth for the affected host routers.
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to apply quirks based on certain adapter types move call to
tb_check_quirks() happen after the adapters are initialized. This should
not affect the existing quirks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Memory for the usb4->margining needs to be relased for the upstream port
of the router as well, even though the debugfs directory gets released
with the router device removal. Fix this.
Fixes: d0f1e0c2a6 ("thunderbolt: Add support for receiver lane margining")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add QUIRK_NO_CLX to disable the CLx state for hardware which
doesn't supports it.
AMD Yellow Carp and Pink Sardine don't support CLx state,
hence disabling it using QUIRK_NO_CLX.
Cc: stable@vger.kernel.org
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
[mw: added debug log when the quirk is run]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
This includes following Thunderbolt/USB4 changes for the v6.3 merge
window:
- Add support for DisplayPort bandwidth allocation mode
- Debug logging improvements
- Minor cleanups.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=Kegw
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.3 merge window
This includes following Thunderbolt/USB4 changes for the v6.3 merge
window:
- Add support for DisplayPort bandwidth allocation mode
- Debug logging improvements
- Minor cleanups.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Add missing kernel-doc comment to tb_tunnel_maximum_bandwidth()
thunderbolt: Handle bandwidth allocation mode enablement notification
thunderbolt: Add support for DisplayPort bandwidth allocation mode
thunderbolt: Include the additional DP IN double word in debugfs dump
thunderbolt: Add functions to support DisplayPort bandwidth allocation mode
thunderbolt: Increase timeout of DP OUT adapter handshake
thunderbolt: Take CL states into account when waiting for link to come up
thunderbolt: Improve debug logging in tb_available_bandwidth()
thunderbolt: Log DP adapter type
thunderbolt: Use decimal port number in control and tunnel logs too
thunderbolt: Refactor tb_acpi_add_link()
thunderbolt: Use correct type in tb_port_is_clx_enabled() prototype
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the graphics side enables bandwidth allocation mode the DP IN
adapter sends notification to the connection manager about this.
Currently the handler misses this and tries to allocate 0 Mb/s that then
makes the graphics side to think the request failed.
Fix this by properly handling the enablement notification.
Fixes: 6ce3563520 ("thunderbolt: Add support for DisplayPort bandwidth allocation mode")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 spec defines an optional feature that allows the connection
manager to negotiate with the graphics through DPCD registers changes in
the bandwidth allocation dynamically. This is referred as "bandwidth
allocation mode" in the spec. The connection manager uses DP IN adapters
registers to communicate with the graphics, and also gets notifications
from these adapters when the graphics wants to change the bandwidth
allocation. Both the connection manager and the graphics driver needs to
support this.
We check if the DP IN adapter supports this and if it does enable it
before establishing a DP tunnel. Then we react on DP_BW notifications
coming from the DP IN adapter and update the bandwidth allocation
accordingly (within the maximum common capabilities the DP IN/OUT
support).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When DisplayPort bandwidth allocation mode is supported by the DP IN
adapter it has an extra double word in the adapter config space. Include
this in the debugfs register dump.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec defines an additional feature that DP IN adapters can
implement (alongside with the graphics DPCD register set) to support
more dynamic bandwidth management for DisplayPort tunnels. For the
connection manager the communication happens through the DP IN adapter
using a set of registers in the adapter config space allocated for this.
Add functions that export this functionality for the rest of the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Sometimes the current timeout is not enough so increase it to 1500 ms
and while there make the loop use ktime instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If CL states are enabled for the link it may be in these states too when
reading the lane adapter state but it will enter CL0 as soon as there is
traffic in the high-speed lanes. Upon discovery we want to make sure
that is accounted as the link being up, otherwise we end up tearing down
the topology with no good reason.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to see what is going on when bandwidth is being
allocated for tunneling.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to see from the debug logs what type of DisplayPort
adapter is in use or available.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use decimal number instead of hex in port numbers as we have been doing
with other logging functions too. This makes the output more consistent.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When firmware connection manager is in use we should not touch the lane
adapter (well or any) configuration space so do this only when we know
that the software connection manager is active.
Fixes: 8e1de70425 ("thunderbolt: Add support for XDomain lane bonding")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to take minimum of both sides of the USB3 link into consideration,
not just the downstream port. Fix this by calling tb_usb3_max_link_rate()
instead.
Fixes: 0bd680cd90 ("thunderbolt: Add USB3 bandwidth management")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We cannot call PM runtime functions in tb_retimer_scan() because it will
also be called when retimers are scanned from userspace (happens when
there is no device connected on ChromeOS for instance) and at the same
USB4 port runtime resume hook. This leads to hang because neither can
proceed.
Fix this by runtime resuming USB4 ports in tb_scan_port() instead. This
makes sure the ports are runtime PM active when retimers are added under
it while avoiding the reported hang as well.
Reported-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Fixes: 1e56c88ade ("thunderbolt: Runtime resume USB4 port when retimers are scanned")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Convert while loop into do-while with only a single call to
acpi_get_first_physical_node(). No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we return an error even if on-board retimers are found and
that's not expected. Fix this to return an error only if there was one
and 0 otherwise.
Fixes: 1e56c88ade ("thunderbolt: Runtime resume USB4 port when retimers are scanned")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_port_is_clx_enabled() generates a valid warning with gcc-13:
drivers/thunderbolt/switch.c:1286:6: error: conflicting types for 'tb_port_is_clx_enabled' due to enum/integer mismatch; have 'bool(struct tb_port *, unsigned int)' ...
drivers/thunderbolt/tb.h:1050:6: note: previous declaration of 'tb_port_is_clx_enabled' with type 'bool(struct tb_port *, enum tb_clx)' ...
I.e. the type of the 2nd parameter of tb_port_is_clx_enabled() in the
declaration is unsigned int, while the definition spells enum tb_clx.
Synchronize them to the former as the parameter is in fact a mask of the
enum values.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Wake on connect/disconnect is only supported while runtime suspend for
now, which is obviously necessary. It is also not inherently desired for
the system to wakeup on Thunderbolt/USB4 hot plug events. However, we
can still make user in control of waking up the system in the events of
hot plug/unplug.
This patch adds 'wakeup' attribute under 'usb4_portX/power' sysfs
attribute and only enables wakes on connect/disconnect to the respective
port when 'wakeup' is set to 'enabled'. The attribute is set to
'disabled' by default.
Signed-off-by: Rajat Khandelwal <rajat.khandelwal@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Replacing the direct fwnode_property_get_reference_args()
call will this wrapper function.
No functional changes intended.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The variable len is assigned a value that is never read. It is re-assigned
a new value in the following do-while loop and never referenced after
the loop. The assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/thunderbolt/xdomain.c:344:2: warning: Value stored to 'len' is
never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use str_enabled_disabled() helper instead of open coding the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices supported
and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before,
and some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new
chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices
better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different
USB drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BN9g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yljdgCdH4Fev4Nvf2Nokfv0q0krcRB3YpUAn1aZfpb/
EbgxsxhPnTJg+mmXyLms
=IxUy
-----END PGP SIGNATURE-----
Merge tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
Core
----
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO.
This significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF
---
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions.
Expose crash_kexec() to allow BPF to trigger a kernel dump.
Use CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs.
Only structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols
---------
- WiFi: more Extremely High Throughput (EHT) and Multi-Link
Operation (MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state
and RST packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API
----------
- Allow selecting the conduit interface used by each port
in DSA switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting
per traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one
of the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much
as possible. It's one of those magic knobs which seemed like
a good idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers
----------------------
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers
-------
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay
window offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Gsio
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
- Reimplement acpi_get_pci_dev() using the list of physical devices
associated with the given ACPI device object (Rafael Wysocki).
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
- Filter out non-memory resources in is_memory(), add a helper
function to find all memory type resources of an ACPI device object
and use that function in 3 places (Heikki Krogerus).
- Add IRQ override quirks for Asus Vivobook K3402ZA/K3502ZA and ASUS
model S5402ZA (Tamim Khan, Kellen Renshaw).
- Fix acpi_dev_state_d0() kerneldoc (Sakari Ailus).
- Fix up suspend-to-idle support on ASUS Rembrandt laptops (Mario
Limonciello).
- Clean up ACPI platform devices support code (Andy Shevchenko, John
Garry).
- Clean up ACPI bus management code (Andy Shevchenko, ye xingchen).
- Add support for multiple DMA windows with different offsets to the
ACPI device enumeration code and use it on LoongArch (Jianmin Lv).
- Clean up the ACPI LPSS (Intel SoC) driver (Andy Shevchenko).
- Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable (Mario
Limonciello).
- Drop unused dev_fmt() and redundant 'HMAT' prefix from the HMAT
parsing code (Liu Shixin).
- Make ACPI FPDT parsing code avoid calling acpi_os_map_memory() on
invalid physical addresses (Hans de Goede).
- Silence missing-declarations warning related to Apple device
properties management (Lukas Wunner).
- Disable frequency invariance in the CPPC library if registers used
by cppc_get_perf_ctrs() are accessed via PCC (Jeremy Linton).
- Add ACPI disabled check to acpi_cpc_valid() (Perry Yuan).
- Fix Tx acknowledge in the PCC address space handler (Huisong Li).
- Use wait_for_completion_timeout() for PCC mailbox operations (Huisong
Li).
- Release resources on PCC address space setup failure path (Rafael
Mendonca).
- Remove unneeded result variables from APEI code (ye xingchen).
- Print total number of records found during BERT log parsing (Dmitry
Monakhov).
- Drop support for 3 _OSI strings that should not be necessary any
more and update documentation on custom _OSI strings so that adding
new ones is not encouraged any more (Mario Limonciello).
- Drop unneeded result variable from ec_write() (ye xingchen).
- Remove the leftover struct acpi_ac_bl from the ACPI AC driver (Hanjun
Guo).
- Reorder symbols to get rid of a few forward declarations in the ACPI
fan driver (Uwe Kleine-König).
- Add Toshiba Satellite/Portege Z830 ACPI backlight quirk (Arvid
Norlander).
- Add ARM DMA-330 controller to the supported list in the ACPI AMBA
driver (Vijayenthiran Subramaniam).
- Drop references to non-functional 01.org/linux-acpi web site from
MAINTAINERS and Kconfig help texts (Rafael Wysocki).
- Replace strlcpy() with unused retval with strscpy() in the ACPI
support code (Wolfram Sang).
- Do not initialize ret in main() in the pfrut utility (Shi junming).
- Drop useless ACPI DSDT override documentation (Rafael Wysocki).
- Fix a few typos and wording mistakes in the ACPI device enumeration
documentation (Jean Delvare).
- Introduce acpi_dev_uid_to_integer() to convert a _UID string into an
integer value (Andy Shevchenko).
- Use acpi_dev_uid_to_integer() in several places to unify _UID
handling (Andy Shevchenko).
- Drop unused pnpid32_to_pnpid() declaration from PNP code (Gaosheng
Cui).
-----BEGIN PGP SIGNATURE-----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=xyUK
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"ACPI and PNP updates for 6.1-rc1.
These rearrange the ACPI device object initialization code (to get rid
of a redundant parent pointer from struct acpi_device among other
things), unify the _UID handling, drop support for some _OSI strings
that should not be necessary any more, add new IDs to support more
hardware and some more quirks, fix a few issues and clean up code all
over.
Specifics:
- Reimplement acpi_get_pci_dev() using the list of physical devices
associated with the given ACPI device object (Rafael Wysocki)
- Rename ACPI device object reference counting functions (Rafael
Wysocki)
- Rearrange ACPI device object initialization code (Rafael Wysocki)
- Drop parent field from struct acpi_device (Rafael Wysocki)
- Extend the the int3472-tps68470 driver to support multiple
consumers of a single TPS68470 along with the requisite
framework-level support (Daniel Scally)
- Filter out non-memory resources in is_memory(), add a helper
function to find all memory type resources of an ACPI device object
and use that function in 3 places (Heikki Krogerus)
- Add IRQ override quirks for Asus Vivobook K3402ZA/K3502ZA and ASUS
model S5402ZA (Tamim Khan, Kellen Renshaw)
- Fix acpi_dev_state_d0() kerneldoc (Sakari Ailus)
- Fix up suspend-to-idle support on ASUS Rembrandt laptops (Mario
Limonciello)
- Clean up ACPI platform devices support code (Andy Shevchenko, John
Garry)
- Clean up ACPI bus management code (Andy Shevchenko, ye xingchen)
- Add support for multiple DMA windows with different offsets to the
ACPI device enumeration code and use it on LoongArch (Jianmin Lv)
- Clean up the ACPI LPSS (Intel SoC) driver (Andy Shevchenko)
- Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable (Mario
Limonciello)
- Drop unused dev_fmt() and redundant 'HMAT' prefix from the HMAT
parsing code (Liu Shixin)
- Make ACPI FPDT parsing code avoid calling acpi_os_map_memory() on
invalid physical addresses (Hans de Goede)
- Silence missing-declarations warning related to Apple device
properties management (Lukas Wunner)
- Disable frequency invariance in the CPPC library if registers used
by cppc_get_perf_ctrs() are accessed via PCC (Jeremy Linton)
- Add ACPI disabled check to acpi_cpc_valid() (Perry Yuan)
- Fix Tx acknowledge in the PCC address space handler (Huisong Li)
- Use wait_for_completion_timeout() for PCC mailbox operations
(Huisong Li)
- Release resources on PCC address space setup failure path (Rafael
Mendonca)
- Remove unneeded result variables from APEI code (ye xingchen)
- Print total number of records found during BERT log parsing (Dmitry
Monakhov)
- Drop support for 3 _OSI strings that should not be necessary any
more and update documentation on custom _OSI strings so that adding
new ones is not encouraged any more (Mario Limonciello)
- Drop unneeded result variable from ec_write() (ye xingchen)
- Remove the leftover struct acpi_ac_bl from the ACPI AC driver
(Hanjun Guo)
- Reorder symbols to get rid of a few forward declarations in the
ACPI fan driver (Uwe Kleine-König)
- Add Toshiba Satellite/Portege Z830 ACPI backlight quirk (Arvid
Norlander)
- Add ARM DMA-330 controller to the supported list in the ACPI AMBA
driver (Vijayenthiran Subramaniam)
- Drop references to non-functional 01.org/linux-acpi web site from
MAINTAINERS and Kconfig help texts (Rafael Wysocki)
- Replace strlcpy() with unused retval with strscpy() in the ACPI
support code (Wolfram Sang)
- Do not initialize ret in main() in the pfrut utility (Shi junming)
- Drop useless ACPI DSDT override documentation (Rafael Wysocki)
- Fix a few typos and wording mistakes in the ACPI device enumeration
documentation (Jean Delvare)
- Introduce acpi_dev_uid_to_integer() to convert a _UID string into
an integer value (Andy Shevchenko)
- Use acpi_dev_uid_to_integer() in several places to unify _UID
handling (Andy Shevchenko)
- Drop unused pnpid32_to_pnpid() declaration from PNP code (Gaosheng
Cui)"
* tag 'acpi-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (79 commits)
ACPI: LPSS: Deduplicate skipping device in acpi_lpss_create_device()
ACPI: LPSS: Replace loop with first entry retrieval
ACPI: x86: s2idle: Add another ID to s2idle_dmi_table
ACPI: x86: s2idle: Fix a NULL pointer dereference
MAINTAINERS: Drop records pointing to 01.org/linux-acpi
ACPI: Kconfig: Drop link to https://01.org/linux-acpi
ACPI: docs: Drop useless DSDT override documentation
ACPI: DPTF: Drop stale link from Kconfig help
ACPI: x86: s2idle: Add a quirk for ASUSTeK COMPUTER INC. ROG Flow X13
ACPI: x86: s2idle: Add a quirk for Lenovo Slim 7 Pro 14ARH7
ACPI: x86: s2idle: Add a quirk for ASUS ROG Zephyrus G14
ACPI: x86: s2idle: Add a quirk for ASUS TUF Gaming A17 FA707RE
ACPI: x86: s2idle: Add module parameter to prefer Microsoft GUID
ACPI: x86: s2idle: If a new AMD _HID is missing assume Rembrandt
ACPI: x86: s2idle: Move _HID handling for AMD systems into structures
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
...
Merge changes regarding the management of ACPI device objects for
6.1-rc1:
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
* acpi-dev:
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
ACPI: property: Use acpi_dev_parent()
ACPI: Drop redundant acpi_dev_parent() header
ACPI: PM: Fix NULL argument handling in acpi_device_get/set_power()
ACPI: Drop parent field from struct acpi_device
ACPI: scan: Eliminate __acpi_device_add()
ACPI: scan: Rearrange initialization of ACPI device objects
ACPI: scan: Rename acpi_bus_get_parent() and rearrange it
ACPI: Rename acpi_bus_get/put_acpi_device()
This includes following Thunderbolt/USB4 changes for the v6.1 merge
window:
- Support for Intel Meteor Lake integrated Thunderbolt/USB4 controller
- Support for ASMedia USB4 controller NVM firmware upgrade
- Receiver lane margining support
- Few fixes and cleanups.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=67d1
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
"thunderbolt: Changes for v6.1 merge window
This includes following Thunderbolt/USB4 changes for the v6.1 merge
window:
- Support for Intel Meteor Lake integrated Thunderbolt/USB4 controller
- Support for ASMedia USB4 controller NVM firmware upgrade
- Receiver lane margining support
- Few fixes and cleanups.
All these have been in linux-next with no reported issues."
* tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Explicitly enable lane adapter hotplug events at startup
thunderbolt: Use dev_err_probe()
thunderbolt: Convert to use sysfs_emit()/sysfs_emit_at() APIs
thunderbolt: Fix spelling mistake "simultaneusly" -> "simultaneously"
thunderbolt: debugfs: Fix spelling mistakes in seq_puts text
thunderbolt: Add support for ASMedia NVM image format
thunderbolt: Move vendor specific NVM handling into nvm.c
thunderbolt: Provide tb_retimer_nvm_read() analogous to tb_switch_nvm_read()
thunderbolt: Rename and make nvm_read() available for other files
thunderbolt: Extend NVM version fields to 32-bits
thunderbolt: Allow NVM upgrade of USB4 host routers
thunderbolt: Add support for receiver lane margining
thunderbolt: Add helper to check if CL states are enabled on port
thunderbolt: Pass CL state bitmask to tb_port_clx_supported()
thunderbolt: Move port CL state functions into correct place in switch.c
thunderbolt: Move tb_xdomain_parent() to tb.h
thunderbolt: Add support for Intel Meteor Lake
thunderbolt: Add comment where Thunderbolt 4 PCI IDs start
thunderbolt: Add DP OUT resource when DP tunnel is discovered
