This splits off a 'pci-new.c' which is aimed at gradually replacing the
pci-auto backend and the arch/sh/drivers/pci/pci.c core respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new PCI code wants its own bus<->resource mappings instead of the
generic equivalents, so drop the asm-generic include in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This starts moving out the common initialization bits from the various
fixup paths in to the shared init path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the platform code is a bit leaner, we can start consolidating
the various IRQ routing implementations. There are effectively only 2
variants, and the others can use those directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 68b42d1b54 ("sh: sh7785lcr: Map
whole PCI address space.") changed around the semantics of how various
chip-selects are made accessible to PCI. Now that there is a single
large mapping covering from CS0-CS6, there is no longer any need to
do multi-window mapping. Subsequently, all of the differing
implementations can be consolidated in to pci-sh7780.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the PCI I/O and memory window definitions across
the pci-sh7780 users in pci-sh7780 itself. No functional changes, in that
every platform had exactly the same implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the I/O port base isn't being set anywhere, which allows things
like generic_inl() to blow up. Fix this up to point at the PCI IO window.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCIC contains a read-only cache line size register that we can
derive pci_cache_line_size from. So, make sure that the software idea of
the cache line size actually matches the host controller's idea.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Don't use pci_write_reg() for these, as it defaults to 32-bit. Rather
than using the helper, use __raw_writeb() directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks how the host controller is probed, and makes it a bit more
verbose in the event a new type of controller is detected. Additionally,
we also log the revision information.
This now uses the proper access sizes for the vendor/device registers,
rather than relying on a larger access that encapsulated both of them.
Not all devices support 32-bit read cycles for these registers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCI host controller implements a configuration header that
requires a fair bit of hand-holding to initialize properly. By default
it appears as a pre-2.0 host controller given the zeroed out class code,
so fix this up properly.
Some boards that happened to be using the R7780RP version of the PCIC
fixups had set this correctly, but this belongs in the standard
initialization, and is by no means board specific.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
P1SEGADDR is obsolete and will be killed off completely in the future,
so transition off of it and reference P1SEG explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SE7780 has the same PCIC fixup as SDK7780, and SH7785LCR the same
as R7780RP. Switch to using those, and drop the duplicate code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With board_pci_channels now being exported in a single place, update the
boards that duplicated the export.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of sometimes exporting board_pci_channels[] in the board specific
code just export it in one place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a __get_pci_io_base() function which is used to match a port range
against struct pci_channel. This allows us to detect if a port range is
assigned to pci or happens to be legacy port io. While at it, remove unused
cpu-specific cruft.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the code to use __is_pci_memory() instead of
is_pci_memaddr(). __is_pci_memory() loops through all the pci
channels on the system to match memory windows.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the io window base address in struct pci_channel and use that one
instead of SH77xx_PCI_IO_BASE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the base address of the pci host controller registers in struct
pci_channel and use the address in pci_read_reg() and pci_write_reg().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store a struct pci_channel pointer in bus->sysdata. This makes whatever
struct pci_channel assigned to a bus available for sh4_pci_read() and
sh4_pci_write(). We also modify PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM to
use bus->sysdata - this to gives us support for multiple pci channels.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replaces PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM with direct struct
pci_channel access. This allows us to have more than one pci
channel.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an init callback to struct pci_channel and makes sure
it is initialized properly. Code is added to call this init function
from pcibios_init(). Return values are adjusted and a warning is is
printed if init fails.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These patches rework the pci code for the sh architecture.
Currently each board implements some kind of ioport to address mapping.
Some boards use generic_io_base others try passing addresses as io ports.
This is the first set of patches that try to unify the pci code as much
as possible to avoid duplicated code. This will in the end lead to fewer
lines board specific code and more generic code.
This patch makes sure a struct pci_channel pointer is passed along to
various pci functions such as pci_read_reg(), pci_write_reg(),
pci_fixup_pcic(), sh7751_pcic_init() and sh7780_pcic_init().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the problem that cannot work PCI device on 32-bit mode because
influence of the commit 68b42d1b54
("sh: sh7785lcr: Map whole PCI address space."). So this patch was
implement like a 29-bit mode, map whole physical address space of
DDR-SDRAM.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PCI still doesn't work on sh7785lcr 29bit 256M map mode.
On SH7785, PCI -> SHwy address translation is not base+offset but
somewhat like base|offset (See HW Manual (rej09b0261) Fig. 13.11).
So, you can't export CS2,3,4,5 by 256M at CS2 (results CS0,1,2,3
exported, I guess). There are two candidates.
a) 128M@CS2 + 128M@CS4
b) 512M@CS0
Attached patch is B. It maps 512M Byte at 0 independently of memory
size. It results CS0 to CS6 and perhaps some more being accessible
from PCI.
Tested on
7785lcr 29bit 128M map
7785lcr 29bit 256M map
(NOT tested on 32bit)
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This accidentally regressed when the multi-IRQ changes went in,
switching SH7091 from 4 to 6 channels. Add SH7091 back in to the
4-channel dependency list.
Reported-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When SuperH CPU has IRQ multi of DMAC, SH_DMA_IRQ_MULTI becomes enable.
The following CPU's are Multi IRQ of DMAC now.
- SH775X and SH7091
- SH776X
- SH7780
- SH7785
If SH_DMA_IRQ_MULTI becomes enable, dma-sh api driver is optimized
for Multi IRQ.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
dma-sh's get_dma_error_irq() is only used by SH4, as the SH3
doesn't have the DMA Error interrupt.
Disable it out for non-SH4 builds.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.
This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the problem that cannot work a PCI device when 32-bit physical
address mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the sh simple_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This also fixes up a long-standing bug for this platform where the PIO
base was set to a register offset, rather than the actual PIO offset
itself.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the problem that cannot work a PCI device when system memory size is
256Mbyte in 29bit address mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7709 datasheet defines bit 5 as set for burst mode, clear for
cycle-steal mode.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh7709 hardware manual says DMAOR is 16 bits long on this platform.
Tested and working with a modified smsc911x ethernet driver (sh-dma
support patch for this driver is coming soon).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
