The protect_page() function was incorrectly setting up the hardware tables
based on possible access capabilities rather than the actual requested
values. This means we would grant more access to mmap-ed pages than we
should have. Once we fix this, we need to tweak the signal generated by
such accesses to aline ourselves with other ports. This allows the LTP
mmap0{5,6,7} cases to run properly.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
I2C_BOARD_INFO() already sets .type, no need to set it again.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Push the device table to the board resources as data interpretation can be
changed on a per-board basis.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The end of the stack may not be valid (and that could be OK), so do not
attempt to parse it. If we do, we might use a bad pointer in kernel space
which makes things panic().
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add the bf538 version of bfin_clear_PPI_STATUS() to match all other ports.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The initial BF54x port included some defines to keep code simple across
different processors, but it just ended up causing the UART0 DMA IRQs to
be set to the UART1 channels.
Signed-off-by: Stefan Pledl <stefan.pledl@mesutronic.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow hardware errors to be caught during early portions of booting, and
leave something in the shadow console that people can use to debug their
system with (to be printed out by the bootloader on next reset).
This enables the hardare error interrupts in head.S, allowing us to find
hardware errors when they happen (well, as much as you can with a hardware
error) and prints out the trace if it is enabled. This will catch errors
(like booting the wrong image on a 533) which previously resulted in a
infinite loop/hang, as well as random hardware errors before before
setup_arch().
To disable this debug only feature - turn off EARLY_PRINTK.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add a memory based shadow console to keep a copy of the printk buffer in a
location which can be found externally. This allows bootloaders to locate
and utilize the log buffer in case of silent (early/resume/etc...) crashes.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The FDPIC arches support a standard set of ptrace requests so rather than
define our own custom API, hook up those requests for common code to
leverage.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than defining the locks and initializing them all the time, only do
so when we actually need them (i.e. the SRAM regions exist). This avoids
dead data and code bloat during runtime.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove code duplication, and only print out memory warnings when they are
an actual problem.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current module relocation code has spotty handling wrt different
memory regions (like L1 instruction). Rather than try to fix each
little spot, use the new common memory functions to greatly simplify
everything and make sure it is always correct.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current module section handling code has a lot of verbose statements
copied and pasted throughout which makes it pretty hard to digest at a
glance. By unifying all of these up front, it is a lot easier to quickly
get an idea of what is actually going on.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert all printk() statements to use the common pr_xxx() funcs and use
the new pr_fmt() function to standardize all of the output.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All kernel modules are required to be built with -mlong-calls and thus
should not generate any of these relocations. If they do, it means the
module has not been compiled properly, so rather than trying to handle
them (and running into random run time errors) just error out on module
load to force the module to be compiled correctly.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that we have a Blackfin memory function to figure out how to properly
access the different regions, drop the custom memory range checks in our
ptrace code and use that. It makes the code nicer and fixes bugs where
the ptrace logic wasn't handling all the different regions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Unify the address display to shrink the code, and add missing decoding of
a few special Blackfin-specific regions (L1 ROM and MMRs).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cleanup is performed in two ways:
- remove extraneous updates of IPEND[4] w/ CONFIG_IPIPE,
and document remaining use.
- substitute pop-reg-from-stack instructions with plain SP fixups in
all save-RETI-then-discard patterns.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The purpose of the EVT14 handler may depend on whether CONFIG_IPIPE is
enabled, albeit its implementation can be the same in both cases. When
the interrupt pipeline is enabled, EVT14 can be used to raise the core
priority level for the running code; when CONFIG_IPIPE is off, EVT14
can be used to lower this level before running softirq handlers.
Rename evt14_softirq to evt_evt14 to pick an identifier that fits
both, which allows to reuse the same vector setup code as well.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
ret_from_fork is always entered with hw interrupts off, which prevents
real-time domains to preempt the Linux kernel during part of the
initial context switch to the new task, which could in turn raise the
worst-case latency figures.
To avoid this, stall the root domain stage in the interrupt pipeline
to keep the scheduling tail code free from Linux-handled IRQs, then
enable hardware interrupts again.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
__ipipe_{stall, unstall}_root_raw() identifiers may leave the reader
under the impression that only the virtual state is affected by these
operations, which is wrong. Pick names following the convention used
throughout the interrupt pipeline code.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We handle many exceptions at EVT5 (hardware error level) so that we can
catch exceptions in our exception handling code. Today - if the global
interrupt enable bit (IPEND[4]) is set (interrupts disabled) our trap
handling code goes into a infinite loop, since we need interrupts to be
on to defer things to EVT5.
Normal kernel code should not trigger this for any reason as IPEND[4] gets
cleared early (when doing an interrupt context save) and the kernel stack
there should be sane (or something much worse is happening in the system).
But there have been a few times where this has happened, so this change
makes sure we dump a proper crash message even when things have gone south.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (46 commits)
powerpc64: convert to dynamic percpu allocator
sparc64: use embedding percpu first chunk allocator
percpu: kill lpage first chunk allocator
x86,percpu: use embedding for 64bit NUMA and page for 32bit NUMA
percpu: update embedding first chunk allocator to handle sparse units
percpu: use group information to allocate vmap areas sparsely
vmalloc: implement pcpu_get_vm_areas()
vmalloc: separate out insert_vmalloc_vm()
percpu: add chunk->base_addr
percpu: add pcpu_unit_offsets[]
percpu: introduce pcpu_alloc_info and pcpu_group_info
percpu: move pcpu_lpage_build_unit_map() and pcpul_lpage_dump_cfg() upward
percpu: add @align to pcpu_fc_alloc_fn_t
percpu: make @dyn_size mandatory for pcpu_setup_first_chunk()
percpu: drop @static_size from first chunk allocators
percpu: generalize first chunk allocator selection
percpu: build first chunk allocators selectively
percpu: rename 4k first chunk allocator to page
percpu: improve boot messages
percpu: fix pcpu_reclaim() locking
...
Fix trivial conflict as by Tejun Heo in kernel/sched.c
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
The default values of HARDIRQ_BITS and PREEMPT_BITS in common code leads to
build failure:
In file included from include/linux/interrupt.h:12,
from include/linux/kernel_stat.h:8,
from arch/blackfin/kernel/asm-offsets.c:32:
include/linux/hardirq.h:66:2: error: #error PREEMPT_ACTIVE is too low!
So until that gets resolved, just declare our own default value again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Check that the result of kmalloc is not NULL before passing it to other
functions.
In the first two cases, the new code returns -ENOMEM, which seems
compatible with what is done for similar functions for other architectures.
In the last two cases, the new code fails silently, ie just returns,
because the function has void return type.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin SMP port was missing CPLB entries for Core B on-chip L1 SRAM
regions. Any code that attempted to use these would wrongly crash due to
a CPLB miss.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Similar to anomaly 05000281 but not as bad, we cannot return to the
instruction causing a fault otherwise we'll trigger a second false
exception. The system can still recover, but it isn't correct.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On Blackfin SMP, a per-cpu loops_per_jiffy is pointless since both cores
always run at the same CCLK. In addition, the current implementation has
flaws since the main consumer for loops_per_jiffy (asm/delay.h) uses the
global kernel loops_per_jiffy and not the per_cpu one. So punt all of the
per-cpu handling and go back to the global shared one.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Change the bfin_gpio_pm_hibernate_restore() function to:
1) AND restored DATA with DIR (not OR) to get correct final state
2) Restore DATA before setting DIR to avoid glitches
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The AD7142 add-on card hooks the IRQ line up to PG5, not PF5.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The interrupt context save logic incorrectly stored the address of the
IPEND register rather than its value due to a missing dereference. While
we're here, also enable this code for all kernel debugging scenarios and
not just when KGDB is enabled.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We already catch this anomaly at compile time, and the runtime version is
such that it ends up checking on all parts rather than just the ones that
might actually have it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This anomaly only applies to the BF527-0.1, not the BF526-0.1, and not any
other revision of the BF527. So make sure we don't go returning 0xffff
for other cases.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The early logic to locate a free DMA channel and then set it up was broken
in a few ways that only manifested itself when we needed to set up more
than 2 on chip SRAM regions (most board defaults setup 1 or 2). First, we
checked the wrong status register (the destination gets updated, not the
source) and second, we did the ssync before rather than after resetting a
DMA config register.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than assume Core B is always run with caches turned on, let people
load into any of the on-chip memory regions. It is their business how the
SRAM/Cache regions are utilized, so don't prevent them from being able to
load into them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The code used in the Blackfin lshrdi3 utilizes gcc constructs. However,
the structures declared don't line up with the code gcc generates, so
under certain optimizations, we get bad code and things crap out in fun
random ways. So rather than trying to maintain different gcc definitions
ourselves, just use the ones available in gcclib.h.
URL: http://blackfin.uclinux.org/gf/tracker/5286
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since we need to relocate the attached filesystem with the uClinux MTD map
(to handle some anomalies), we need to know its real filesize. If we boot
a kernel without a filesystem actually attached, we end up blindly reading
and copying garbage (since there is no magic value to detect validity).
Often times this results in an early crash and no output. So add a few
basic sanity checks before operating on things to catch the majority of
cases.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Previous unification code put the exception banner behind the "is oops"
logic when it should have been printed all the time.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add missing anomaly workaround for anomaly 05000281 - we can't return to
instructions which cause hardware errors otherwise we trigger the error
again which means we go into an infinite loop of handling, returning, and
retriggering. This work around confuses gdb when the error occurs as the
PC will seemed to have moved, so a better long term fix will need to be
figured out, but for now this is better than an infinite crash loop.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are no CONFIG_{BLK,CHR}_DEV_FLASH Kconfig options, and there is no
flash_probe() function, so not really sure what this code is all about.
Seems to be dead code that stretches way back to the start of the Blackfin
port.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Improve the assembly with a few explanatory comments and use symbolic
defines rather than numeric values for bit positions.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Discarded sections in different archs share some commonality but have
considerable differences. This led to linker script for each arch
implementing its own /DISCARD/ definition, which makes maintaining
tedious and adding new entries error-prone.
This patch makes all linker scripts to move discard definitions to the
end of the linker script and use the common DISCARDS macro. As ld
uses the first matching section definition, archs can include default
discarded sections by including them earlier in the linker script.
ia64 is notable because it first throws away some ia64 specific
subsections and then include the rest of the sections into the final
image, so those sections must be discarded before the inclusion.
defconfig compile tested for x86, x86-64, powerpc, powerpc64, ia64,
alpha, sparc, sparc64 and s390. Michal Simek tested microblaze.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Cc: linux-arch@vger.kernel.org
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Tony Luck <tony.luck@intel.com>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
There are a few places where ___cacheline_aligned* is used with
DEFINE_PER_CPU(). Use DEFINE_PER_CPU_SHARED_ALIGNED() instead.
DEFINE_PER_CPU_SHARED_ALIGNED() applies alignment only on SMPs. While
all other converted places used _in_smp variant or only get compiled
for SMP, net/rds used unconditional ____cacheline_aligned. I don't
see any reason these data structures should be aligned on UP and thus
converted together.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andy Grover <andy.grover@oracle.com>
x86 throws away .discard section but no other archs do. Also,
.discard is not thrown away while linking modules. Make every arch
and module linking throw it away. This will be used to define dummy
variables for percpu declarations and definitions.
This patch is based on Ivan Kokshaysky's alpha percpu patch.
[ Impact: always throw away everything in .discard ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
The recent deprecation of dma_sync_{sg,single} ironically broke Blackfin
systems. This is because we don't define dma_sync_sg_for_cpu at all, so
until the DMA asm-generic conversion/cleanup is done after the next
release, simply stub out the dma_sync_sg_for_{cpu,device} functions.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't support the BF535 at all, and the exception 0x2A text specific to
it is pretty verbose and confusing (since the behavior is simply odd), so
punt it to keep the noise down.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we process the kernel command line before poking the hardware,
so that we can process early printk. This helps ensure that if you boot
a kernel configured for a different processor, something will be left in
the log buffer.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The GPTMR0_CLOCKSOURCE Kconfig option requires the gptimers framework, so
make sure it is selected when this option is enabled.
Reported-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD changed SDRAM chips between board revisions, so create a
timing table that can accommodate both.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We defined SDRAM_tRAS to TRAS_4, but then wrongly defined SDRAM_tRAS_num
to 3.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many aspects of the Blackfin memory map is exactly the same across all
variants. Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file. In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than use "Linux" in the boot image name (as this is redundant --
the image type is already set to "linux"), use the CPU name. This makes
it fairly obvious when a wrong image is accidentally booted. Otherwise
there is no kernel output and you waste time scratching your head
wondering wtf just happened.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache. Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem. The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.
So split the configure options such that they properly reflect the settings
that are applied to the hardware.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD has a SST SPI flash on it, not a ST Micro.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We read the SWRST (Software Reset) register to get at the last reset
state, and then we may configure the DOUBLE_FAULT bit to control behavior
when a double fault occurs. But if the lower bits of the register is
already set (like UART boot mode on a BF54x), we inadvertently make the
system reset by writing to the SYSTEM_RESET field at the same time. So
make sure the lower 4 bits are always cleared.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Split out the optional IRQ14 lowering code to further simplify the
asm_do_IRQ() function and keep the ifdef nest under control.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Take a page from x86 and abstract the stack checking out of the
asm_do_IRQ() function so that the result is easier to digest.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With the common IRQ code initializing much more of the irq_desc state, we
can't blindly initialize it ourselves to the local bad_irq state. If we
do, we end up wrongly clobbering many fields. So punt most of the bad irq
code as the common layers will handle the default state, and simply call
handle_bad_irq() directly when the IRQ we are processing is invalid.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF533-EZKIT has two Flash In-System Programming devices hooked up to
the async memory bus, so add resources for the primary flashes and the
SRAMs on the devices.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The kgdb (in multiple places) and traps code developed pretty much
identical checks for how to access different regions of the Blackfin
memory map, but each wasn't 100%, so unify them to avoid duplication,
bitrot, and bugs with edge cases.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
