Some DSA switches have multiple CPU ports, which can be used to improve
CPU termination throughput, but DSA, through dsa_tree_setup_cpu_ports(),
sets up only the first one, leading to suboptimal use of hardware.
The desire is to not change the default configuration but to permit the
user to create a dynamic mapping between individual user ports and the
CPU port that they are served by, configurable through rtnetlink. It is
also intended to permit load balancing between CPU ports, and in that
case, the foreseen model is for the DSA master to be a bonding interface
whose lowers are the physical DSA masters.
To that end, we create a struct rtnl_link_ops for DSA user ports with
the "dsa" kind. We expose the IFLA_DSA_MASTER link attribute that
contains the ifindex of the newly desired DSA master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
All the users of these functions are gone, delete them before they gain
new ones.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reduce a number of included headers to a necessary minimum.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang static analysis reports this representative issue
dsa.c:486:2: warning: Undefined or garbage value
returned to caller
return err;
^~~~~~~~~~
err is only set in the loop. If the loop is empty,
garbage will be returned. So initialize err to 0
to handle this noop case.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ocelot" and "ocelot-8021q" tagging protocols make use of different
hardware resources, and host FDB entries have different destination
ports in the switch analyzer module, practically speaking.
So when the user requests a tagging protocol change, the driver must
migrate all host FDB and MDB entries from the NPI port (in fact CPU port
module) towards the same physical port, but this time used as a regular
port.
It is pointless for the felix driver to keep a copy of the host
addresses, when we can create and export DSA helpers for walking through
the addresses that it already needs to keep on the CPU port, for
refcounting purposes.
felix_classify_db() is moved up to avoid a forward declaration.
We pass "bool change" because dp->fdbs and dp->mdbs are uninitialized
lists when felix_setup() first calls felix_set_tag_protocol(), so we
need to avoid calling dsa_port_walk_fdbs() during probe time.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink_resources_unregister() used second parameter as an
entry point for the recursive removal of devlink resources. None
of the callers outside of devlink core needed to use this field,
so let's remove it.
As part of this removal, the "struct devlink_resource" was moved
from .h to .c file as it is not possible to use in any place in
the code except devlink.c.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since Vivien's conversion of the ds->ports array into a dst->ports
list, and the introduction of dsa_to_port, iterations through the ports
of a switch became quadratic whenever dsa_to_port was needed.
dsa_to_port can either be called directly, or indirectly through the
dsa_is_{user,cpu,dsa,unused}_port helpers.
Use the newly introduced dsa_switch_for_each_port() iteration macro
that works with the iterator variable being a struct dsa_port *dp
directly, and not an int i. It is an expensive variable to go from i to
dp, but cheap to go from dp to i.
This macro iterates through the entire ds->dst->ports list and filters
by the ports belonging just to the switch provided as argument.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when unbinding the mv88e6xxx driver on Turris MOX, these error
messages appear:
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 0 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 100 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 0 from fdb: -2
(and similarly for other ports)
What happens is that DSA has a policy "even if there are bugs, let's at
least not leak memory" and dsa_port_teardown() clears the dp->fdbs and
dp->mdbs lists, which are supposed to be empty.
But deleting that cleanup code, the warnings go away.
=> the FDB and MDB lists (used for refcounting on shared ports, aka CPU
and DSA ports) will eventually be empty, but are not empty by the time
we tear down those ports. Aka we are deleting them too soon.
The addresses that DSA complains about are host-trapped addresses: the
local addresses of the ports, and the MAC address of the bridge device.
The problem is that offloading those entries happens from a deferred
work item scheduled by the SWITCHDEV_FDB_DEL_TO_DEVICE handler, and this
races with the teardown of the CPU and DSA ports where the refcounting
is kept.
In fact, not only it races, but fundamentally speaking, if we iterate
through the port list linearly, we might end up tearing down the shared
ports even before we delete a DSA user port which has a bridge upper.
So as it turns out, we need to first tear down the user ports (and the
unused ones, for no better place of doing that), then the shared ports
(the CPU and DSA ports). In between, we need to ensure that all work
items scheduled by our switchdev handlers (which only run for user
ports, hence the reason why we tear them down first) have finished.
Fixes: 161ca59d39 ("net: dsa: reference count the MDB entries at the cross-chip notifier level")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914134726.2305133-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently DSA exposes the following sysfs:
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
which is a read-only device attribute, introduced in the kernel as
commit 98cdb48071 ("net: dsa: Expose tagging protocol to user-space"),
and used by libpcap since its commit 993db3800d7d ("Add support for DSA
link-layer types").
It would be nice if we could extend this device attribute by making it
writable:
$ echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
This is useful with DSA switches that can make use of more than one
tagging protocol. It may be useful in dsa_loop in the future too, to
perform offline testing of various taggers, or for changing between dsa
and edsa on Marvell switches, if that is desirable.
In terms of implementation, drivers can support this feature by
implementing .change_tag_protocol, which should always leave the switch
in a consistent state: either with the new protocol if things went well,
or with the old one if something failed. Teardown of the old protocol,
if necessary, must be handled by the driver.
Some things remain as before:
- The .get_tag_protocol is currently only called at probe time, to load
the initial tagging protocol driver. Nonetheless, new drivers should
report the tagging protocol in current use now.
- The driver should manage by itself the initial setup of tagging
protocol, no later than the .setup() method, as well as destroying
resources used by the last tagger in use, no earlier than the
.teardown() method.
For multi-switch DSA trees, error handling is a bit more complicated,
since e.g. the 5th out of 7 switches may fail to change the tag
protocol. When that happens, a revert to the original tag protocol is
attempted, but that may fail too, leaving the tree in an inconsistent
state despite each individual switch implementing .change_tag_protocol
transactionally. Since the intersection between drivers that implement
.change_tag_protocol and drivers that support D in DSA is currently the
empty set, the possibility for this error to happen is ignored for now.
Testing:
$ insmod mscc_felix.ko
[ 79.549784] mscc_felix 0000:00:00.5: Adding to iommu group 14
[ 79.565712] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
$ insmod tag_ocelot.ko
$ rmmod mscc_felix.ko
$ insmod mscc_felix.ko
[ 97.261724] libphy: VSC9959 internal MDIO bus: probed
[ 97.267363] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0
[ 97.274998] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1
[ 97.282561] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2
[ 97.289700] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3
[ 97.599163] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.862034] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.950731] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[ 97.964278] 8021q: adding VLAN 0 to HW filter on device swp0
[ 98.146161] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.238649] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[ 98.251845] 8021q: adding VLAN 0 to HW filter on device swp1
[ 98.433916] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.485542] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[ 98.503584] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 98.527948] device eno2 entered promiscuous mode
[ 98.544755] DSA: tree 0 setup
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=2.337 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.754 ms
^C
- 10.0.0.1 ping statistics -
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.754/1.545/2.337 ms
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
$ cat ./test_ocelot_8021q.sh
#!/bin/bash
ip link set swp0 down
ip link set swp1 down
ip link set swp2 down
ip link set swp3 down
ip link set swp5 down
ip link set eno2 down
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
ip link set eno2 up
ip link set swp0 up
ip link set swp1 up
ip link set swp2 up
ip link set swp3 up
ip link set swp5 up
$ ./test_ocelot_8021q.sh
./test_ocelot_8021q.sh: line 9: echo: write error: Protocol not available
$ rmmod tag_ocelot.ko
rmmod: can't unload module 'tag_ocelot': Resource temporarily unavailable
$ insmod tag_ocelot_8021q.ko
$ ./test_ocelot_8021q.sh
$ cat /sys/class/net/eno2/dsa/tagging
ocelot-8021q
$ rmmod tag_ocelot.ko
$ rmmod tag_ocelot_8021q.ko
rmmod: can't unload module 'tag_ocelot_8021q': Resource temporarily unavailable
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=0.953 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.787 ms
64 bytes from 10.0.0.1: seq=2 ttl=64 time=0.771 ms
$ rmmod mscc_felix.ko
[ 645.544426] mscc_felix 0000:00:00.5: Link is Down
[ 645.838608] DSA: tree 0 torn down
$ rmmod tag_ocelot_8021q.ko
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packets ingressing on a LAG that egress on the CPU port, which are not
classified as management, will have a FORWARD tag that does not
contain the normal source device/port tuple. Instead the trunk bit
will be set, and the port field holds the LAG id.
Since the exact source port information is not available in the tag,
frames are injected directly on the LAG interface and thus do never
pass through any DSA port interface on ingress.
Management frames (TO_CPU) are not affected and will pass through the
DSA port interface as usual.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This effectively reverts commit 60724d4bae ("net: dsa: Add support for
DSA specific notifiers"). The reason is that since commit 2f1e8ea726
("net: dsa: link interfaces with the DSA master to get rid of lockdep
warnings"), it appears that there is a generic way to achieve the same
purpose. The only user thus far, the Broadcom SYSTEMPORT driver, was
converted to use the generic notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of dsa_slave_priv for storing
a pointer to the per-cpu counters. This allows us to use core
functionality for statistics handling.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow DSA drivers to make use of devlink port regions, via simple
wrappers.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver needs to call dsa_untag_bridge_pvid(), it can
set dsa_switch::untag_brige_pvid to indicate this is necessary.
This is a pre-requisite to making sure that we are always calling
dsa_untag_bridge_pvid() after eth_type_trans() has been called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA drivers to make use of devlink regions, via simple wrappers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given a devlink instance, return the dsa switch it is associated to.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As its implementation shows, this is synonimous with calling
dsa_slave_dev_check followed by dsa_slave_to_port, so it is quite simple
already and provides functionality which is already there.
However there is now a need for these functions outside dsa_priv.h, for
example in drivers that perform mirroring and redirection through
tc-flower offloads (they are given raw access to the flow_cls_offload
structure), where they need to call this function on act->dev.
But simply exporting dsa_slave_to_port would make it non-inline and
would result in an extra function call in the hotpath, as can be seen
for example in sja1105:
Before:
000006dc <sja1105_xmit>:
{
6dc: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e0: e1a04000 mov r4, r0
6e4: e591958c ldr r9, [r1, #1420] ; 0x58c <- Inline dsa_slave_to_port
6e8: e1a05001 mov r5, r1
6ec: e24dd004 sub sp, sp, #4
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6f0: e1c901d8 ldrd r0, [r9, #24]
6f4: ebfffffe bl 0 <dsa_8021q_tx_vid>
6f4: R_ARM_CALL dsa_8021q_tx_vid
u8 pcp = netdev_txq_to_tc(netdev, queue_mapping);
6f8: e1d416b0 ldrh r1, [r4, #96] ; 0x60
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6fc: e1a08000 mov r8, r0
After:
000006e4 <sja1105_xmit>:
{
6e4: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e8: e1a04000 mov r4, r0
6ec: e24dd004 sub sp, sp, #4
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f0: e1a00001 mov r0, r1
{
6f4: e1a05001 mov r5, r1
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f8: ebfffffe bl 0 <dsa_slave_to_port>
6f8: R_ARM_CALL dsa_slave_to_port
6fc: e1a09000 mov r9, r0
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
700: e1c001d8 ldrd r0, [r0, #24]
704: ebfffffe bl 0 <dsa_8021q_tx_vid>
704: R_ARM_CALL dsa_8021q_tx_vid
Because we want to avoid possible performance regressions, introduce
this new function which is designed to be public.
Suggested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort of "encapsulation", and we can use the same mechs to
greatly improve overall DSA performance.
skbs are passed to the GRO layer after removing CPU tags, so we don't
need any new packet offload types as it was firstly proposed by me in
the first GRO-over-DSA variant [1].
The size of struct gro_cells is sizeof(void *), so hot struct
dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields
remain in one 32-byte cacheline.
The other positive side effect is that drivers for network devices
that can be shipped as CPU ports of DSA-driven switches can now use
napi_gro_frags() to pass skbs to kernel. Packets built that way are
completely non-linear and are likely being dropped without GRO.
This was tested on to-be-mainlined-soon Ethernet driver that uses
napi_gro_frags(), and the overall performance was on par with the
variant from [1], sometimes even better due to minimal overhead.
net.core.gro_normal_batch tuning may help to push it to the limit
on particular setups and platforms.
iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup
on 1.2 GHz MIPS board:
5.7-rc2 baseline:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender
[ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver
Iface RX packets TX packets
eth0 7097731 7097702
port0 426050 6671829
port1 6671681 425862
port1.218 6671677 425851
With this patch:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender
[ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver
Iface RX packets TX packets
eth0 9474792 9474777
port0 455200 353288
port1 9019592 455035
port1.218 353144 455024
v2:
- Add some performance examples in the commit message;
- No functional changes.
[1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/
Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in preparing the module name in a buffer. The format
string can be passed diectly to 'request_module()'.
This axes a few lines of code and cleans a few things:
- max len for a driver name is MODULE_NAME_LEN wich is ~ 60 chars,
not 128. It would be down-sized in 'request_module()'
- we should pass the total size of the buffer to 'snprintf()', not the
size minus 1
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wrappers around the devlink resource API, so that DSA drivers can
register and unregister devlink resources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add plumbing to allow DSA drivers to register parameters with devlink.
To keep with the abstraction, the DSA drivers pass the ds structure to
these helpers, and the DSA core then translates that to the devlink
structure associated to the device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the _get and _put functions to make use of the list of tag
drivers. Also, trigger the loading of the module, based on the alias
information. The _get function takes a reference on the tag driver, so
it cannot be unloaded, and the _put function releases the reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Make tag_driver_register void
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver is unloaded, the lock on the tag driver
should be released so the module can be unloaded. Add the needed calls,
but leave the actual release code as a stub.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_resolve_tag_protocol() is used to find the tagging driver needed
by a switch driver. When the tagging drivers become modules, it will
be necassary to take a reference on the module to prevent it being
unloaded. So rename this function to _get() to indicate it has some
locking properties.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The none tagger is special in that it does not live in a tag_*.c file,
but is within the core. Register/unregister when DSA is
loaded/unloaded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the tag drivers register themselves with the DSA core, keeping
them in a linked list.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA tag driver module will need to register the tag protocols it
implements with the DSA core. Add macros containing this boiler plate.
The registration/unregistration code is currently just a stub. A Later
patch will add the real implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Fix indent of #endif
Rewrite to move list pointer into a new structure
v3
Move kdoc next to macro
Fix THIS_MODULE indentation
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that we can match the tagging protocol a switch driver
request to the tagger, we need to know what protocol the tagger
supports. Add this information to the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
More tag protocol to end of structure to keep hot members at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than keep a list to map a tagger ops to a name, place the name
into the ops structure. This removes the hard coded list, a step
towards making the taggers more dynamic.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Move name to end of structure, keeping the hot entries at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ9893 switch is similar to KSZ9477 switch except the ingress tail tag
has 1 byte instead of 2 bytes. The size of the portmap is smaller and
so the override and lookup bits are also moved.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gswip tag was missing in the dsa_tag_protocol_to_str() function, add it.
Fixes: 7969119293 ("net: dsa: Add Lantiq / Intel GSWIP tag support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This handles the tag added by the PMAC on the VRX200 SoC line.
The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.
This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no way for user-space to know what a given DSA network device's
tagging protocol is. Expose this information through a dsa/tagging
attribute which reflects the tagging protocol currently in use.
This is helpful for configuration (e.g: none behaves dramatically
different wrt. bridges) as well as for packet capture tools when there
is not a proper Ethernet type available.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52638f71fc ("dsa: Move gpio reset into switch driver")
moved the GPIO handling into the switch drivers but forgot
to remove the GPIO header includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward the rx/tx timestamp machinery from the dsa infrastructure to the
switch driver.
On the rx side, defer delivery of skbs until we have an rx timestamp.
This mimicks the behavior of skb_defer_rx_timestamp.
On the tx side, identify PTP packets, clone them, and pass them to the
underlying switch driver before we transmit. This mimicks the behavior
of skb_tx_timestamp.
Adjusted txstamp API to keep the allocation and freeing of the clone
in the same central function by Richard Cochran
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new bindings (dsa2.c) and the old bindings (legacy.c) share two
helpers dsa_cpu_dsa_setup and dsa_cpu_dsa_destroy, used to register or
deregister a fixed PHY if a given port has a corresponding device node.
Unclutter the code by moving them into two new port.c helpers,
dsa_port_fixed_link_register_of and dsa_port_fixed_link_(un)register_of.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.
This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
