Instead of setting bits manually we use set_bit, test_bit, etc.
Also remove L2CAP_ prefix from macros.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Management interface commands for blocking and unblocking devices.
Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This workaround aims to break the deadlock situation
which raises during continuous transfer of data for long
duration over uart with hardware flow control. It is
observed that CTS interrupt cannot be cleared in uart
interrupt register (ICR). Hence further transfer over
uart gets blocked.
It is seen that during such deadlock condition ICR
don't get cleared even on multiple write. This leads
pass_counter to decrease and finally reach zero. This
can be taken as trigger point to run this UART_BT_WA.
Workaround backups the register configuration, does soft
reset of UART using BIT-0 of PRCC_K_SOFTRST_SET/CLEAR
registers and restores the registers.
This patch also provides support for uart init and exit
function calls if present.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move blacklisting functions to hci_core.c, so that they can
be used by both management interface and hci socket interface.
Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The clocksource watchdog code is interruptible and it has been
observed that this can trigger false positives which disable the TSC.
The reason is that an interrupt storm or a long running interrupt
handler between the read of the watchdog source and the read of the
TSC brings the two far enough apart that the delta is larger than the
unstable treshold. Move both reads into a short interrupt disabled
region to avoid that.
Reported-and-tested-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
AFS: Use i_generation not i_version for the vnode uniquifier
AFS: Set s_id in the superblock to the volume name
vfs: Fix data corruption after failed write in __block_write_begin()
afs: afs_fill_page reads too much, or wrong data
VFS: Fix vfsmount overput on simultaneous automount
fix wrong iput on d_inode introduced by e6bc45d65d
Delay struct net freeing while there's a sysfs instance refering to it
afs: fix sget() races, close leak on umount
ubifs: fix sget races
ubifs: split allocation of ubifs_info into a separate function
fix leak in proc_set_super()
The hash:net,iface type makes possible to store network address and
interface name pairs in a set. It's mostly suitable for egress
and ingress filtering. Examples:
# ipset create test hash:net,iface
# ipset add test 192.168.0.0/16,eth0
# ipset add test 192.168.0.0/24,eth1
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
With the change the sets can use any parameter available for the match
and target extensions, like input/output interface. It's required for
the hash:net,iface set type.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The patch "Fix adding ranges to hash types" had got a mistypeing
in the timeout variant of the hash types, which actually made
the patch ineffective. Fixed!
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The range internally is converted to the network(s) equal to the range.
Example:
# ipset new test hash:net
# ipset add test 10.2.0.0-10.2.1.12
# ipset list test
Name: test
Type: hash:net
Header: family inet hashsize 1024 maxelem 65536
Size in memory: 16888
References: 0
Members:
10.2.1.12
10.2.1.0/29
10.2.0.0/24
10.2.1.8/30
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
A set type may have multiple revisions, for example when syntax is
extended. Support continuous revision ranges in set types.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When ranges are added to hash types, the elements may trigger rehashing
the set. However, the last successfully added element was not kept track
so the adding started again with the first element after the rehashing.
Bug reported by Mr Dash Four.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Current listing makes possible to list sets with full content only.
The patch adds support partial listings, i.e. listing just
the existing setnames or listing set headers, without set members.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The support makes possible to specify the timeout value for
the SET target and a flag to reset the timeout for already existing
entries.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When an element to a set with timeout added, one can change the timeout
by "readding" the element with the "-exist" flag. That means the timeout
value is reset to the specified one (or to the default from the set
specification if the "timeout n" option is not used). Example
ipset add foo 1.2.3.4 timeout 10
ipset add foo 1.2.3.4 timeout 600 -exist
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Avoid double seq adjustment for loopback traffic
because it causes silent repetition of TCP data. One
example is passive FTP with DNAT rule and difference in the
length of IP addresses.
This patch adds check if packet is sent and
received via loopback device. As the same conntrack is
used both for outgoing and incoming direction, we restrict
seq adjustment to happen only in POSTROUTING.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Make GPIOF_ defined values available even when GPIOLIB nor GENERIC_GPIO
is enabled by moving them to <linux/gpio.h>.
Fixes these build errors in linux-next:
sound/soc/codecs/ak4641.c:524: error: 'GPIOF_OUT_INIT_LOW' undeclared (first use in this function)
sound/soc/codecs/wm8915.c:2921: error: 'GPIOF_OUT_INIT_LOW' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some RS690 chipsets seem to end up with floating connectors, either
a DVI connector isn't actually populated, or an add-in HDMI card
is available but not installed. In this case we seem to get a NULL byte
response for each byte of the i2c transaction, so we detect this
case and if we see it we don't do anymore DDC transactions on this
connector.
I've tested this on my RS690 without the HDMI card installed and
it seems to work fine.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "hostname" tool falls back to setting the hostname to "localhost" if
/etc/hostname does not exist. Distribution init scripts have the same
fallback. However, if userspace never calls sethostname, such as when
booting with init=/bin/sh, or otherwise booting a minimal system without
the usual init scripts, the default hostname of "(none)" remains,
unhelpfully appearing in various places such as prompts ("root@(none):~#")
and logs. Furthermore, "(none)" doesn't typically resolve to anything
useful.
Make the default hostname configurable. This removes the need for the
standard fallback, provides a useful default for systems that never call
sethostname, and makes minimal systems that much more useful with less
configuration. Distributions could choose to use "localhost" here to
avoid the fallback, while embedded systems may wish to use a specific
target hostname.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Kel Modderman <kel@otaku42.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BUILD_BUG_ON_ZERO and BUILD_BUG_ON_NULL must return values, even in the
CHECKER case otherwise various users of it become syntactically invalid.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently, Robert Mueller reported (http://lkml.org/lkml/2010/9/12/236)
that zone_reclaim_mode doesn't work properly on his new NUMA server (Dual
Xeon E5520 + Intel S5520UR MB). He is using Cyrus IMAPd and it's built on
a very traditional single-process model.
* a master process which reads config files and manages the other
process
* multiple imapd processes, one per connection
* multiple pop3d processes, one per connection
* multiple lmtpd processes, one per connection
* periodical "cleanup" processes.
There are thousands of independent processes. The problem is, recent
Intel motherboard turn on zone_reclaim_mode by default and traditional
prefork model software don't work well on it. Unfortunatelly, such models
are still typical even in the 21st century. We can't ignore them.
This patch raises the zone_reclaim_mode threshold to 30. 30 doesn't have
any specific meaning. but 20 means that one-hop QPI/Hypertransport and
such relatively cheap 2-4 socket machine are often used for traditional
servers as above. The intention is that these machines don't use
zone_reclaim_mode.
Note: ia64 and Power have arch specific RECLAIM_DISTANCE definitions.
This patch doesn't change such high-end NUMA machine behavior.
Dave Hansen said:
: I know specifically of pieces of x86 hardware that set the information
: in the BIOS to '21' *specifically* so they'll get the zone_reclaim_mode
: behavior which that implies.
:
: They've done performance testing and run very large and scary benchmarks
: to make sure that they _want_ this turned on. What this means for them
: is that they'll probably be de-optimized, at least on newer versions of
: the kernel.
:
: If you want to do this for particular systems, maybe _that_'s what we
: should do. Have a list of specific configurations that need the
: defaults overridden either because they're buggy, or they have an
: unusual hardware configuration not really reflected in the distance
: table.
And later said:
: The original change in the hardware tables was for the benefit of a
: benchmark. Said benchmark isn't going to get run on mainline until the
: next batch of enterprise distros drops, at which point the hardware where
: this was done will be irrelevant for the benchmark. I'm sure any new
: hardware will just set this distance to another yet arbitrary value to
: make the kernel do what it wants. :)
:
: Also, when the hardware got _set_ to this initially, I complained. So, I
: guess I'm getting my way now, with this patch. I'm cool with it.
Reported-by: Robert Mueller <robm@fastmail.fm>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix <linux/kmsg_dump.h> when CONFIG_PRINTK is not enabled:
include/linux/kmsg_dump.h:56: error: 'EINVAL' undeclared (first use in this function)
include/linux/kmsg_dump.h:61: error: 'EINVAL' undeclared (first use in this function)
Looks like commit 595dd3d8bf ("kmsg_dump: fix build for
CONFIG_PRINTK=n") uses EINVAL without having the needed header file(s),
but I'm sure that I build tested that patch also. oh well.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While testing for memcg aware swap token, I observed a swap token was
often grabbed an intermittent running process (eg init, auditd) and they
never release a token.
Why?
Some processes (eg init, auditd, audispd) wake up when a process exiting.
And swap token can be get first page-in process when a process exiting
makes no swap token owner. Thus such above intermittent running process
often get a token.
And currently, swap token priority is only decreased at page fault path.
Then, if the process sleep immediately after to grab swap token, the swap
token priority never be decreased. That's obviously undesirable.
This patch implement very poor (and lightweight) priority aging. It only
be affect to the above corner case and doesn't change swap tendency
workload performance (eg multi process qsbench load)
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, memcg reclaim can disable swap token even if the swap token mm
doesn't belong in its memory cgroup. It's slightly risky. If an admin
creates very small mem-cgroup and silly guy runs contentious heavy memory
pressure workload, every tasks are going to lose swap token and then
system may become unresponsive. That's bad.
This patch adds 'memcg' parameter into disable_swap_token(). and if the
parameter doesn't match swap token, VM doesn't disable it.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Rik van Riel<riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't support header padding yet so better off ditching it
Reported-by: Sid Moore <learnmost@gmail.com>
Signed-off-by: Benny Halevy <benny@tonian.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the NLM daemon is killed on the NFS server, we can currently end up
hanging forever on an 'unlock' request, instead of aborting. Basically,
if the rpcbind request fails, or the server keeps returning garbage, we
really want to quit instead of retrying.
Tested-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
This patch changes to code to use some of the preprocessor
definitions from mii.h over its homegrown equivalents.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
Commit a26ac2455ffcf3(rcu: move TREE_RCU from softirq to kthread)
introduced performance regression. In an AIM7 test, this commit degraded
performance by about 40%.
The commit runs rcu callbacks in a kthread instead of softirq. We observed
high rate of context switch which is caused by this. Out test system has
64 CPUs and HZ is 1000, so we saw more than 64k context switch per second
which is caused by RCU's per-CPU kthread. A trace showed that most of
the time the RCU per-CPU kthread doesn't actually handle any callbacks,
but instead just does a very small amount of work handling grace periods.
This means that RCU's per-CPU kthreads are making the scheduler do quite
a bit of work in order to allow a very small amount of RCU-related
processing to be done.
Alex Shi's analysis determined that this slowdown is due to lock
contention within the scheduler. Unfortunately, as Peter Zijlstra points
out, the scheduler's real-time semantics require global action, which
means that this contention is inherent in real-time scheduling. (Yes,
perhaps someone will come up with a workaround -- otherwise, -rt is not
going to do well on large SMP systems -- but this patch will work around
this issue in the meantime. And "the meantime" might well be forever.)
This patch therefore re-introduces softirq processing to RCU, but only
for core RCU work. RCU callbacks are still executed in kthread context,
so that only a small amount of RCU work runs in softirq context in the
common case. This should minimize ksoftirqd execution, allowing us to
skip boosting of ksoftirqd for CONFIG_RCU_BOOST=y kernels.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: "Alex,Shi" <alex.shi@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This patch implements a check in smp cmd pairing request and pairing
response to verify if encryption key maximum size is compatible in both
slave and master when SMP Pairing is requested. Keys are also masked to
the correct negotiated size.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds support for disconnecting the link when SMP procedure
takes more than 30 seconds.
SMP begins when either the Pairing Request command is sent or the
Pairing Response is received, and it ends when the link is encrypted
(or terminated). Vol 3, Part H Section 3.4.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
After restructuring, there is some unused or empty functions
left to be removed.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
SLAB: Record actual last user of freed objects.
slub: always align cpu_slab to honor cmpxchg_double requirement
jbd2_journal_remove_journal_head() can oops when trying to access
journal_head returned by bh2jh(). This is caused for example by the
following race:
TASK1 TASK2
jbd2_journal_commit_transaction()
...
processing t_forget list
__jbd2_journal_refile_buffer(jh);
if (!jh->b_transaction) {
jbd_unlock_bh_state(bh);
jbd2_journal_try_to_free_buffers()
jbd2_journal_grab_journal_head(bh)
jbd_lock_bh_state(bh)
__journal_try_to_free_buffer()
jbd2_journal_put_journal_head(jh)
jbd2_journal_remove_journal_head(bh);
jbd2_journal_put_journal_head() in TASK2 sees that b_jcount == 0 and
buffer is not part of any transaction and thus frees journal_head
before TASK1 gets to doing so. Note that even buffer_head can be
released by try_to_free_buffers() after
jbd2_journal_put_journal_head() which adds even larger opportunity for
oops (but I didn't see this happen in reality).
Fix the problem by making transactions hold their own journal_head
reference (in b_jcount). That way we don't have to remove journal_head
explicitely via jbd2_journal_remove_journal_head() and instead just
remove journal_head when b_jcount drops to zero. The result of this is
that [__]jbd2_journal_refile_buffer(),
[__]jbd2_journal_unfile_buffer(), and
__jdb2_journal_remove_checkpoint() can free journal_head which needs
modification of a few callers. Also we have to be careful because once
journal_head is removed, buffer_head might be freed as well. So we
have to get our own buffer_head reference where it matters.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If the pending security level is greater than the current security
level and the link is now encrypted, we should update the link
security level.
This is only useful for LE links, when the only event generated
when SMP is sucessful in the Encrypt Change event.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This adds support for starting SMP Phase 2 Encryption, when the initial
SMP negotiation is successful. This adds the LE Start Encryption and LE
Long Term Key Request commands and related events.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch includes support for generating and sending the random value
used to produce the confirmation value.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds initial support for verifying the confirmation value
that the remote side has sent.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This will allow using the crypto subsystem for encrypting data. As SMP
(Security Manager Protocol) is implemented almost entirely on the host
side and the crypto module already implements the needed methods
(AES-128), it makes sense to use it.
There's now a new module option to enable/disable SMP support.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This implementation only exchanges SMP messages between the Host and the
Remote. No keys are being generated. TK and STK generation will be
provided in further patches.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This will be removed in -next so let's drop it from mainline as soon as
we can in order to minimise surprises.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These simple commands will allow the SMP procedure to be started
and terminated with a not supported error. This is the first step
toward something useful.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
ERTM use the generic L2CAP timer functions to keep a reference to the
channel. This is useful for avoiding crashes.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
struct l2cap_chan has now its own refcnt that is compatible with the
socket refcnt, i.e., we won't see sk_refcnt = 0 and chan->refcnt > 0.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now socket state is tracked by struct sock and channel state is tracked by
chan->state. At this point both says the same, but this is going to change
when we add AMP Support for example.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add an abstraction layer between L2CAP core and its users (only
l2cap_sock.c now). The first function implemented is new_connection() that
replaces calls to l2cap_sock_alloc() in l2cap_core.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use the compiler to verify format strings and arguments.
Fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Make it more clear what the functions does,
on request by Julian.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Remove variable ctl_key from struct netns_ipvs,
it's a leftover from early netns work.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
* new refcount in struct net, controlling actual freeing of the memory
* new method in kobj_ns_type_operations (->drop_ns())
* ->current_ns() semantics change - it's supposed to be followed by
corresponding ->drop_ns(). For struct net in case of CONFIG_NET_NS it bumps
the new refcount; net_drop_ns() decrements it and calls net_free() if the
last reference has been dropped. Method renamed to ->grab_current_ns().
* old net_free() callers call net_drop_ns() instead.
* sysfs_exit_ns() is gone, along with a large part of callchain
leading to it; now that the references stored in ->ns[...] stay valid we
do not need to hunt them down and replace them with NULL. That fixes
problems in sysfs_lookup() and sysfs_readdir(), along with getting rid
of sb->s_instances abuse.
Note that struct net *shutdown* logics has not changed - net_cleanup()
is called exactly when it used to be called. The only thing postponed by
having a sysfs instance refering to that struct net is actual freeing of
memory occupied by struct net.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio/basic_mmio: add missing include of spinlock_types.h
gpio/nomadik: fix sleepmode for elder Nomadik
SNMP mibs use two percpu arrays, one used in BH context, another in USER
context. With increasing number of cpus in machines, and fact that ipv6
uses per network device ipstats_mib, this is consuming a lot of memory
if many network devices are registered.
commit be281e554e (ipv6: reduce per device ICMP mib sizes) shrinked
percpu needs for ipv6, but we can reduce memory use a bit more.
With recent percpu infrastructure (irqsafe_cpu_inc() ...), we no longer
need this BH/USER separation since we can update counters in a single
x86 instruction, regardless of the BH/USER context.
Other arches than x86 might need to disable irq in their
irqsafe_cpu_inc() implementation : If this happens to be a problem, we
can make SNMP_ARRAY_SZ arch dependent, but a previous poll
( https://lkml.org/lkml/2011/3/17/174 ) to arch maintainers did not
raise strong opposition.
Only on 32bit arches, we need to disable BH for 64bit counters updates
done from USER context (currently used for IP MIB)
This also reduces vmlinux size :
1) x86_64 build
$ size vmlinux.before vmlinux.after
text data bss dec hex filename
7853650 1293772 1896448 11043870 a8841e vmlinux.before
7850578 1293772 1896448 11040798 a8781e vmlinux.after
2) i386 build
$ size vmlinux.before vmlinux.afterpatch
text data bss dec hex filename
6039335 635076 3670016 10344427 9dd7eb vmlinux.before
6037342 635076 3670016 10342434 9dd022 vmlinux.afterpatch
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <andi@firstfloor.org>
CC: Ingo Molnar <mingo@elte.hu>
CC: Tejun Heo <tj@kernel.org>
CC: Christoph Lameter <cl@linux-foundation.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org
CC: linux-arch@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing of VLAN_FLAG_REORDER_HDR does not belong in vlan_untag
but rather in vlan_do_receive. Otherwise the vlan header
will not be properly put on the packet in the case of
vlan header accelleration.
As we remove the check from vlan_check_reorder_header
rename it vlan_reorder_header to keep the naming clean.
Fix up the skb->pkt_type early so we don't look at the packet
after adding the vlan tag, which guarantees we don't goof
and look at the wrong field.
Use a simple if statement instead of a complicated switch
statement to decided that we need to increment rx_stats
for a multicast packet.
Hopefully at somepoint we will just declare the case where
VLAN_FLAG_REORDER_HDR is cleared as unsupported and remove
the code. Until then this keeps it working correctly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need for the guest to validate the checksum if it have been
validated by host nics. So this patch introduces a new flag -
VIRTIO_NET_HDR_F_DATA_VALID which is used to bypass the checksum
examing in guest. The backend (tap/macvtap) may set this flag when
met skbs with CHECKSUM_UNNECESSARY to save cpu utilization.
No feature negotiation is needed as old driver just ignore this flag.
Iperf shows 12%-30% performance improvement for UDP traffic. For TCP,
when gro is on no difference as it produces skb with partial
checksum. But when gro is disabled, 20% or even higher improvement
could be measured by netperf.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It uses cpu_relax(), and so needs <asm/processor.h>
Without this patch, I see:
CC arch/mn10300/kernel/asm-offsets.s
In file included from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:57,
from arch/mn10300/kernel/asm-offsets.c:7:
include/linux/seqlock.h: In function 'read_seqbegin':
include/linux/seqlock.h:91: error: implicit declaration of function 'cpu_relax'
whilst building asb2364_defconfig on MN10300.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Store the cdev pointer in struct irctl, allocated dynamically as needed,
rather than having a static array. At the same time, recycle some of the
saved memory to nudge the maximum number of lirc devices supported up a
ways -- its not that uncommon these days, now that we have the rc-core
lirc bridge driver, to see a system with at least 4 raw IR receivers.
(consider a mythtv backend with several video capture devices and the
possible need for IR transmit hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the brcm80211 driver we disable the 80211 core when the driver is
'down'. The bcma_core_disable() function exactly does the same as
our implementation so exporting this function makes sense.
Cc: linux-wireless@vger.kernel.org
Cc: Rafal Milecki <zajec5@gmail.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ieee80211_get_operstate() function to get the operstate
of the netdevice.
This is needed for drivers that need to know when the interface
is IF_OPER_UP (e.g. wl12xx), and block notifiers can't be used
(e.g. because the interface is already IF_OPER_UP, like after
resuming from suspend)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
include/linux/basic_mmio_gpio.h uses a spinlock_t without including any
of the spinlock headers resulting in this compiler warning.
include/linux/basic_mmio_gpio.h:51:2: error: expected specifier-qualifier-list before 'spinlock_t'
Explicitly include linux/spinlock_types.h to fix it.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: iio: max517: Fix iio_info changes
Staging: mei: fix debug code
Staging: cx23885: fix include of altera.h
staging: iio: error case memory leak fix
staging: ath6kl: Fix a kernel panic during suspend/resume
staging: gma500: get control from firmware framebuffer if conflicts
staging: gma500: Skip bogus LVDS VBT mode and check for LVDS before adding backlight
staging: usbip: bugfix prevent driver unbind
staging: iio: industrialio-trigger: set iio_poll_func private_data
staging: rts_pstor: use bitwise operator instead of logical one
staging: fix ath6kl build when CFG80211 is not enabled
staging: brcm80211: fix for 'multiple definition of wl_msg_level' build err
staging: fix olpc_dcon build, needs BACKLIGHT_CLASS_DEVICE
Staging: remove STAGING_EXCLUDE_BUILD option
Staging: altera: move .h file to proper place
* 'stable/xen-swiotlb.bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb-2.6:
swiotlb: Export swioltb_nr_tbl and utilize it as appropiate.
Profiles show false sharing in addr_compare() because refcnt/dtime
changes dirty the first inet_peer cache line, where are lying the keys
used at lookup time. If many cpus are calling inet_getpeer() and
inet_putpeer(), or need frag ids, addr_compare() is in 2nd position in
"perf top".
Before patch, my udpflood bench (16 threads) on my 2x4x2 machine :
5784.00 9.7% csum_partial_copy_generic [kernel]
3356.00 5.6% addr_compare [kernel]
2638.00 4.4% fib_table_lookup [kernel]
2625.00 4.4% ip_fragment [kernel]
1934.00 3.2% neigh_lookup [kernel]
1617.00 2.7% udp_sendmsg [kernel]
1608.00 2.7% __ip_route_output_key [kernel]
1480.00 2.5% __ip_append_data [kernel]
1396.00 2.3% kfree [kernel]
1195.00 2.0% kmem_cache_free [kernel]
1157.00 1.9% inet_getpeer [kernel]
1121.00 1.9% neigh_resolve_output [kernel]
1012.00 1.7% dev_queue_xmit [kernel]
# time ./udpflood.sh
real 0m44.511s
user 0m20.020s
sys 11m22.780s
# time ./udpflood.sh
real 0m44.099s
user 0m20.140s
sys 11m15.870s
After patch, no more addr_compare() in profiles :
4171.00 10.7% csum_partial_copy_generic [kernel]
1787.00 4.6% fib_table_lookup [kernel]
1756.00 4.5% ip_fragment [kernel]
1234.00 3.2% udp_sendmsg [kernel]
1191.00 3.0% neigh_lookup [kernel]
1118.00 2.9% __ip_append_data [kernel]
1022.00 2.6% kfree [kernel]
993.00 2.5% __ip_route_output_key [kernel]
841.00 2.2% neigh_resolve_output [kernel]
816.00 2.1% kmem_cache_free [kernel]
658.00 1.7% ia32_sysenter_target [kernel]
632.00 1.6% kmem_cache_alloc_node [kernel]
# time ./udpflood.sh
real 0m41.587s
user 0m19.190s
sys 10m36.370s
# time ./udpflood.sh
real 0m41.486s
user 0m19.290s
sys 10m33.650s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andi Kleen and Tim Chen reported huge contention on inetpeer
unused_peers.lock, on memcached workload on a 40 core machine, with
disabled route cache.
It appears we constantly flip peers refcnt between 0 and 1 values, and
we must insert/remove peers from unused_peers.list, holding a contended
spinlock.
Remove this list completely and perform a garbage collection on-the-fly,
at lookup time, using the expired nodes we met during the tree
traversal.
This removes a lot of code, makes locking more standard, and obsoletes
two sysctls (inet_peer_gc_mintime and inet_peer_gc_maxtime). This also
removes two pointers in inet_peer structure.
There is still a false sharing effect because refcnt is in first cache
line of object [were the links and keys used by lookups are located], we
might move it at the end of inet_peer structure to let this first cache
line mostly read by cpus.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <andi@firstfloor.org>
CC: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch lowers the default initRTO from 3secs to 1sec per
RFC2988bis. It falls back to 3secs if the SYN or SYN-ACK packet
has been retransmitted, AND the TCP timestamp option is not on.
It also adds support to take RTT sample during 3WHS on the passive
open side, just like its active open counterpart, and uses it, if
valid, to seed the initRTO for the data transmission phase.
The patch also resets ssthresh to its initial default at the
beginning of the data transmission phase, and reduces cwnd to 1 if
there has been MORE THAN ONE retransmission during 3WHS per RFC5681.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to remove all support for displaying an ntuple as
strings via ETHTOOL_GRXNTUPLE. The reason for this change is due to the
fact that multiple issues have been found including:
- Multiple buffer overruns for strings being displayed.
- Incorrect filters displayed, cleared filters with ring of -2 are displayed
- Setting get_rx_ntuple displays no rules if defined.
- Endianess wrong on displayed values.
- Hard limit of 1024 filters makes display functionality extremely limited
The only driver that had supported this interface was ixgbe. Since it no
longer uses the interface and due to the issues mentioned above I am
submitting this patch to remove it.
v2:
Updated based on comments from Ben Hutchings
- Left ETH_SS_NTUPLE_FILTERS in code but commented on it being deprecated
- Removed ethtool_rx_ntuple_list and ethtool_rx_ntuple_flow_spec_container
- Left ETHTOOL_GRXNTUPLE but commented it as deprecated
Also cleaned up set_rx_ntuple since there is no flow spec container to
maintain we can drop all the code for the alloc and free of it and just
return ops->set_rx_ntuple().
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tries to make the 'struct inode' accesses denser in the data cache
by moving a commonly accessed field (i_security) closer to other fields
that are accessed often.
It also makes 'i_state' just an 'unsigned int' rather than 'unsigned
long', since we only use a few bits of that field, and moves it next to
the existing 'i_flags' so that we potentially get better structure
layout (although depending on config options, i_flags may already have
packed in the same word as i_lock, so this improves packing only for the
case of spinlock debugging)
Out 'struct inode' is still way too big, and we should probably move
some other fields around too (the acl fields in particular) for better
data cache access density. Other fields (like the inode hash) are
likely to be entirely irrelevant under most loads.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add BT_POWER socket option used to control the power
characteristics of the underlying ACL link. When the remote end
has put the link in sniff mode and the host stack wants to send
data we need need to explicitly exit sniff mode to work well with
certain devices (For example, A2DP on Plantronics Voyager 855).
However, this causes problems with HID devices.
Hence, moving into active mode when sending data, irrespective
of who set the sniff mode has been made as a socket option. By
default, we will move into active mode. HID devices can set the
L2CAP socket option to prevent this from happening.
Currently, this has been implemented for L2CAP sockets. This has been
tested with incoming and outgoing L2CAP sockets for HID and A2DP.
Based on discussions on linux-bluetooth and patches submitted by
Andrei Emeltchenko.
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new field (dst_type) to the struct hci_conn which
holds the type of the destination address (bdaddr_t dst). This
approach is needed in order to use the struct hci_conn as an
abstraction of LE connections in HCI Layer. For non-LE this field
is ignored.
This patch also set properly the 'dst_type' field after initializing
LE hci_conn structures.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Legacy devices don't re-authenticate the link properly if a link key
already exists. Thus, don't update sec_level for this case even if
hci_auth_complete_evt indicates success. Otherwise the sec_level will
not reflect a real security on the link.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a timer to clear 'adv_entries' after three minutes.
After some amount of time, the advertising entries cached during
the last LE scan should be considered expired and they should be
removed from the advertising cache.
It was chosen a three minutes timeout as an initial attempt. This
value might change in future.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The LE advertising cache should be cleared before performing a LE
scanning. This will force the cache to contain only fresh advertising
entries.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements the LE advertising cache. It stores sensitive
information (bdaddr and bdaddr_type so far) gathered from LE
advertising report events.
Only advertising entries from connectables devices are added to the
cache.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds definitions and a new struct for Advertising Report
Event from LE and Dual Mode controllers.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The call to l2cap_chan_clear_timer() is not really needed in l2cap_sock.c.
This patch also adds a call to l2cap_chan_clear_timer() to the only place
in __l2cap_sock_close() that wasn't calling it. It's safe call it there
because l2cap_chan_clear_timer() check first for timer_peding().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The new timer does not belong to struct sock, tought it still touch some
sock things, but this will be sorted out soon.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
chan_type says if our chan is raw(direclty access to HCI),
connection less or connection oriented.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This move all the sending logic to l2cap_core.c, but we still have a
socket dependence there, struct msghdr. It will be removed in some of the
further commits.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This is actually __l2cap_sock_close() renamed to __l2cap_chan_close().
At a first look it may not make sense, but with the further cleanups that
will come it will.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix comments in include/linux/perf_event.h
perf: Comment /proc/sys/kernel/perf_event_paranoid to be part of user ABI
perf python: Fix argument name list of read_on_cpu()
perf evlist: Don't die if sample_{id_all|type} is invalid
perf python: Use exception to propagate errors
perf evlist: Remove dependency on debug routines
perf, cgroups: Fix up for new API
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] soc_camera: preserve const attribute
[media] uvc_entity: initialize return value
[media] media: Fix media device minor registration
[media] Make nchg variable signed because the code compares this variable against negative values
[media] omap3isp: fix compiler warning
[media] v4l: Fix media_entity_to_video_device macro argument name
[media] ivtv: Internally separate encoder & decoder standard setting
[media] ivtvfb: Add sanity check to ivtvfb_pan_display()
[media] ivtvfb: use display information in info not in var for panning
[media] ivtv: Make two ivtv_msleep_timeout calls uninterruptable
[media] anysee: return EOPNOTSUPP for unsupported I2C messages
[media] gspca - ov519: Set the default frame rate to 15 fps
[media] gspca - stv06xx: Set a lower default value of gain for hdcs sensors
[media] gspca: Remove coarse_expo_autogain.h
[media] gspca - ov519: Change the ovfx2 bulk transfer size
[media] gspca - ov519: Fix a regression for ovfx2 webcams
* 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/atom: fix PHY init
drm/radeon/kms: add missing Evergreen texture formats to the CS parser
drm/radeon/kms: viewport height has to be even
drm/radeon/kms: remove duplicate reg from r600 safe regs
drm/radeon/kms: add support for Llano Fusion APUs
drm/radeon/kms: add llano pci ids
drm/radeon/kms: fill in asic struct for llano
drm/radeon/kms: add family ids for llano APUs
drm/radeon: fix oops in ttm reserve when pageflipping (v2)
drm/radeon/kms: clean up the radeon kms Kconfig
drm/radeon/kms: fix thermal sensor reading on juniper
drm/radeon/kms: add missing case for cayman thermal sensor
drm/radeon/kms: add blit support for cayman (v2)
drm/radeon/kms/blit: workaround some hw issues on evergreen+
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
vfs: make unlink() and rmdir() return ENOENT in preference to EROFS
lmLogOpen() broken failure exit
usb: remove bad dput after dentry_unhash
more conservative S_NOSEC handling
Staging drivers should be self-contained, without files in the include/
directories. So move the altera.h file back to the driver directory for
now, until it moves out of the staging tree.
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The CN_NETLINK_USERS must be set to the highest valid index +1.
Thanks to Evgeniy for pointing this out.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@kernel.org> [.39]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices support BT/WLAN co-existence algorigthms.
In order not to harm the system performance and user experience, the device
requests not to allow any RX BA session and tear down existing RX BA sessions
based on system constraints such as periodic BT activity that needs to limit
WLAN activity (eg.SCO or A2DP).
In such cases, the intention is to limit the duration of the RX PPDU and
therefore prevent the peer device to use A-MPDU aggregation.
Adding ieee80211_stop_rx_ba_session() callback
that can be used by the driver to stop existing BA sessions.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some USB mass-storage devices have bugs that cause them not to handle
the first READ(10) command they receive correctly. The Corsair
Padlock v2 returns completely bogus data for its first read (possibly
it returns the data in encrypted form even though the device is
supposed to be unlocked). The Feiya SD/SDHC card reader fails to
complete the first READ(10) command after it is plugged in or after a
new card is inserted, returning a status code that indicates it thinks
the command was invalid, which prevents the kernel from retrying the
read.
Since the first read of a new device or a new medium is for the
partition sector, the kernel is unable to retrieve the device's
partition table. Users have to manually issue an "hdparm -z" or
"blockdev --rereadpt" command before they can access the device.
This patch (as1470) works around the problem. It adds a new quirk
flag, US_FL_INVALID_READ10, indicating that the first READ(10) should
always be retried immediately, as should any failing READ(10) commands
(provided the preceding READ(10) command succeeded, to avoid getting
stuck in a loop). The patch also adds appropriate unusual_devs
entries containing the new flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sven Geggus <sven-usbst@geggus.net>
Tested-by: Paul Hartman <paul.hartman+linux@gmail.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2.6.27, commit 393e52e33c (packet: deliver VLAN TCI to userspace)
added a small information leak.
Add padding field and make sure its zeroed before copy to user.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface uses a temporary buffer, but for no real reason.
And now can generate warnings like:
net/sched/sch_generic.c: In function dev_watchdog
net/sched/sch_generic.c:254:10: warning: unused variable drivername
Just return driver->name directly or "".
Reported-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default the io_tlb_nslabs is set to zero, and gets set to
whatever value is passed in via swiotlb_init_with_tbl function.
The default value passed in is 64MB. However, if the user provides
the 'swiotlb=<nslabs>' the default value is ignored and
the value provided by the user is used... Except when the SWIOTLB
is used under Xen - there the default value of 64MB is used and
the Xen-SWIOTLB has no mechanism to get the 'io_tlb_nslabs' filled
out by setup_io_tlb_npages functions. This patch provides a function
for the Xen-SWIOTLB to call to see if the io_tlb_nslabs is set
and if so use that value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Commit b0b0c0a26e "nfsd: add proc file listing kernel's gss_krb5
enctypes" added an nunnecessary dependency of nfsd on the auth_rpcgss
module.
It's a little ad hoc, but since the only piece of information nfsd needs
from rpcsec_gss_krb5 is a single static string, one solution is just to
share it with an include file.
Cc: stable@kernel.org
Reported-by: Michael Guntsche <mike@it-loops.com>
Cc: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
While creating fixed tracepoints for ext3, basically by porting them
from ext4, I found a lot of useless retyping, wrong type usage, useless
variable passing and other inconsistencies in the ext4 fixed tracepoint
code.
This patch cleans the fixed tracepoint code for ext4 and also simplify
some of them.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Following error is raised (and other similar ones) :
net/ipv4/netfilter/nf_nat_standalone.c: In function ‘nf_nat_fn’:
net/ipv4/netfilter/nf_nat_standalone.c:119:2: warning: case value ‘4’
not in enumerated type ‘enum ip_conntrack_info’
gcc barfs on adding two enum values and getting a not enumerated
result :
case IP_CT_RELATED+IP_CT_IS_REPLY:
Add missing enum values
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
tg3: Fix tg3_skb_error_unmap()
net: tracepoint of net_dev_xmit sees freed skb and causes panic
drivers/net/can/flexcan.c: add missing clk_put
net: dm9000: Get the chip in a known good state before enabling interrupts
drivers/net/davinci_emac.c: add missing clk_put
af-packet: Add flag to distinguish VID 0 from no-vlan.
caif: Fix race when conditionally taking rtnl lock
usbnet/cdc_ncm: add missing .reset_resume hook
vlan: fix typo in vlan_dev_hard_start_xmit()
net/ipv4: Check for mistakenly passed in non-IPv4 address
iwl4965: correctly validate temperature value
bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
ath9k: fix two more bugs in tx power
cfg80211: don't drop p2p probe responses
Revert "net: fix section mismatches"
drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
sctp: stop pending timers and purge queues when peer restart asoc
drivers/net: ks8842 Fix crash on received packet when in PIO mode.
ip_options_compile: properly handle unaligned pointer
iwlagn: fix incorrect PCI subsystem id for 6150 devices
...
Fix include/linux/perf_event.h comments to be consistent with
the actual #define names. This is trivial, but it can be a bit
confusing when first reading through the file.
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus@samba.org
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1106031757090.29381@cl320.eecs.utk.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Use hlist_entry() for io_context.cic_list.first
cfq-iosched: Remove bogus check in queue_fail path
xen/blkback: potential null dereference in error handling
xen/blkback: don't call vbd_size() if bd_disk is NULL
block: blkdev_get() should access ->bd_disk only after success
CFQ: Fix typo and remove unnecessary semicolon
block: remove unwanted semicolons
Revert "block: Remove extra discard_alignment from hd_struct."
nbd: adjust 'max_part' according to part_shift
nbd: limit module parameters to a sane value
nbd: pass MSG_* flags to kernel_recvmsg()
block: improve the bio_add_page() and bio_add_pc_page() descriptions
Caching "we have already removed suid/caps" was overenthusiastic as merged.
On network filesystems we might have had suid/caps set on another client,
silently picked by this client on revalidate, all of that *without* clearing
the S_NOSEC flag.
AFAICS, the only reasonably sane way to deal with that is
* new superblock flag; unless set, S_NOSEC is not going to be set.
* local block filesystems set it in their ->mount() (more accurately,
mount_bdev() does, so does btrfs ->mount(), users of mount_bdev() other than
local block ones clear it)
* if any network filesystem (or a cluster one) wants to use S_NOSEC,
it'll need to set MS_NOSEC in sb->s_flags *AND* take care to clear S_NOSEC when
inode attribute changes are picked from other clients.
It's not an earth-shattering hole (anybody that can set suid on another client
will almost certainly be able to write to the file before doing that anyway),
but it's a bug that needs fixing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This reverts commit b1c43f82c5.
It was broken in so many ways, and results in random odd pty issues.
It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af: "tty: fix endless
work loop when the buffer fills up").
It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.
And it didn't actually work at all. BenH bisected down odd tty behavior
to it:
"It looks like the patch is causing some major malfunctions of the X
server for me, possibly related to PTYs. For example, cat'ing a
large file in a gnome terminal hangs the kernel for -minutes- in a
loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
data in the quoted bits further down).
...
Some more data: It -looks- like what happens is that the
flush_to_ldisc work queue entry constantly re-queues itself (because
the PTY is full ?) and the workqueue thread will basically loop
forver calling it without ever scheduling, thus starving the consumer
process that could have emptied the PTY."
which is pretty much exactly the problem we fixed in a5660b41af.
Milton Miller pointed out the 'unsigned int' issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of BCMA cards SPROM is located in the ChipCommon core, it is
not mapped as separated host window. So far we have met only SPROMs rev
8.
SPROM layout seems to be the same as for SSB buses, so we decided to
share SPROM struct and some defines.
For now we extract MAC address only, this can be improved of course.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcm80211 driver in the staging tree has a cordic function to
determine cosine and sine for a given angle. Feedback received from
John Linville suggested that these kind of functions should be made
available to others as a library function in the kernel tree. The
b43 driver also has a cordic angle calculation implemented.
Cc: linux-kernel@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcm80211 driver in staging tree uses a crc8 function. Based on
feedback from John Linville to move this to lib directory, the linux
source has been searched. Although there is currently only one other
kernel driver using this algorithm (ie. drivers/ssb) we are providing
this as a library function for others to use.
Cc: linux-kernel@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Dan Carpenter <error27@gmail.com>
Cc: George Spelvin <linux@horizon.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On an architecture without CMPXCHG_LOCAL but with DEBUG_VM enabled,
the VM_BUG_ON() in __pcpu_double_call_return_bool() will cause an early
panic during boot unless we always align cpu_slab properly.
In principle we could remove the alignment-testing VM_BUG_ON() for
architectures that don't have CMPXCHG_LOCAL, but leaving it in means
that new code will tend not to break x86 even if it is introduced
on another platform, and it's low cost to require alignment.
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
The detection of spurios interrupts is currently limited to first level
handler. In force-threaded mode we never notice if the threaded irq does
not feel responsible.
This patch catches the return value of the threaded handler and forwards
it to the spurious detector. If the primary handler returns only
IRQ_WAKE_THREAD then the spourious detector ignores it because it gets
called again from the threaded handler.
[ tglx: Report the erroneous return value early and bail out ]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/1306824972-27067-2-git-send-email-sebastian@breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Because there is a possibility that skb is kfree_skb()ed and zero cleared
after ndo_start_xmit, we should not see the contents of skb like skb->len and
skb->dev->name after ndo_start_xmit. But trace_net_dev_xmit does that
and causes panic by NULL pointer dereference.
This patch fixes trace_net_dev_xmit not to see the contents of skb directly.
If you want to reproduce this panic,
1. Get tracepoint of net_dev_xmit on
2. Create 2 guests on KVM
2. Make 2 guests use virtio_net
4. Execute netperf from one to another for a long time as a network burden
5. host will panic(It takes about 30 minutes)
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this case, the SCTP association transmits an ASCONF packet
including addition of the new IP address and deletion of the old
address. This patch implements this functionality.
In this case, the ASCONF chunk is added to the beginning of the
queue, because the other chunks cannot be transmitted in this state.
Signed-off-by: Michio Honda <micchie@sfc.wide.ad.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the application to operate Auto-ASCONF on/off
behavior via setsockopt() and getsockopt().
Signed-off-by: Michio Honda <micchie@sfc.wide.ad.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP reconfigure the IP addresses in the association by using
ASCONF chunks as mentioned in RFC5061. For example, we can
start to use the newly configured IP address in the existing
association. This patch implements automatic ASCONF operation
in the SCTP stack with address events in the host computer,
which is called auto_asconf.
Signed-off-by: Michio Honda <micchie@sfc.wide.ad.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user-space cannot determine if a 0 tcp_vlan_tci
means there is no VLAN tag or the VLAN ID was zero.
Add flag to make this explicit. User-space can check for
TP_STATUS_VLAN_VALID || tp_vlan_tci > 0, which will be backwards
compatible. Older could would have just checked for tp_vlan_tci,
so it will work no worse than before.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the CAIF HSI Protocol Driver for the
CAIF Link Layer.
This driver implements a platform driver to accommodate for a
platform specific HSI devices. A general platform driver is not
possible as there are no HSI side Kernel API defined.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Fix off-by-one in RMRR setup
intel-iommu: Add domain check in domain_remove_one_dev_info
intel-iommu: Remove Host Bridge devices from identity mapping
intel-iommu: Use coherent DMA mask when requested
intel-iommu: Dont cache iova above 32bit
intel-iommu: Speed up processing of the identity_mapping function
intel-iommu: Check for identity mapping candidate using system dma mask
intel-iommu: Only unlink device domains from iommu
intel-iommu: Enable super page (2MiB, 1GiB, etc.) support
intel-iommu: Flush unmaps at domain_exit
intel-iommu: Remove obsolete comment from detect_intel_iommu
intel-iommu: fix VT-d PMR disable for TXT on S3 resume
This adds dump support to testmode. The testmode
dump support in nl80211 requires using two of the
six cb->args, the rest can be used by the driver
to figure out where the dump position is at or to
store other data across invocations.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0a35d36 ("cfg80211: Use capability info to detect mesh beacons")
assumed that probe response with both ESS and IBSS bits cleared
means that the frame was sent by a mesh sta.
However, these capabilities are also being used in the p2p_find phase,
and the mesh-validation broke it.
Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies
exist before assuming this frame was sent by a mesh sta.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The name 'entity' is used twice in the macro body, once as the macro
argument, and once as a structure field name. This breaks compilation if
the macro is called with its argument not named 'entity'.
Fix this by renaming the macro argument '__e'. This should avoid
namespace clashes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are no externally-visible changes with this. In the loop in the
internal __domain_mapping() function, we simply detect if we are mapping:
- size >= 2MiB, and
- virtual address aligned to 2MiB, and
- physical address aligned to 2MiB, and
- on hardware that supports superpages.
(and likewise for larger superpages).
We automatically use a superpage for such mappings. We never have to
worry about *breaking* superpages, since we trust that we will always
*unmap* the same range that was mapped. So all we need to do is ensure
that dma_pte_clear_range() will also cope with superpages.
Adjust pfn_to_dma_pte() to take a superpage 'level' as an argument, so
it can return a PTE at the appropriate level rather than always
extending the page tables all the way down to level 1. Again, this is
simplified by the fact that we should never encounter existing small
pages when we're creating a mapping; any old mapping that used the same
virtual range will have been entirely removed and its obsolete page
tables freed.
Provide an 'intel_iommu=sp_off' argument on the command line as a
chicken bit. Not that it should ever be required.
==
The original commit seen in the iommu-2.6.git was Youquan's
implementation (and completion) of my own half-baked code which I'd
typed into an email. Followed by half a dozen subsequent 'fixes'.
I've taken the unusual step of rewriting history and collapsing the
original commits in order to keep the main history simpler, and make
life easier for the people who are going to have to backport this to
older kernels. And also so I can give it a more coherent commit comment
which (hopefully) gives a better explanation of what's going on.
The original sequence of commits leading to identical code was:
Youquan Song (3):
intel-iommu: super page support
intel-iommu: Fix superpage alignment calculation error
intel-iommu: Fix superpage level calculation error in dma_pfn_level_pte()
David Woodhouse (4):
intel-iommu: Precalculate superpage support for dmar_domain
intel-iommu: Fix hardware_largepage_caps()
intel-iommu: Fix inappropriate use of superpages in __domain_mapping()
intel-iommu: Fix phys_pfn in __domain_mapping for sglist pages
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix build warnings in physmap.h:
include/linux/mtd/physmap.h:25: warning: 'struct platform_device' declared inside parameter list
include/linux/mtd/physmap.h:25: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/mtd/physmap.h:26: warning: 'struct platform_device' declared inside parameter list
include/linux/mtd/physmap.h:27: warning: 'struct platform_device' declared inside parameter list
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the peer restart the asoc, we should not only fail any unsent/unacked
data, but also stop the T3-rtx, SACK, T4-rto timers, and teardown ASCONF
queues.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking over the code I found that with the ttwu rework the
nr_wakeups_migrate test broke since we now switch cpus prior to
calling ttwu_stat(), hence the test is always true.
Cure this by passing the migration state in wake_flags. Also move the
whole test under CONFIG_SMP, its hard to migrate tasks on UP :-)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-pwwxl7gdqs5676f1d4cx6pj7@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since those defined functions require additional semicolon
from the caller, they could cause potential syntax errors
when used in if-else statements.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It was not a good idea to start dereferencing disk->queue from
the fs sysfs strategy for displaying discard alignment. We ran
into first a NULL pointer deref, and after fixing that we sometimes
see unvalid disk->queue pointer values.
Since discard is the only one of the bunch actually looking into
the queue, just revert the change.
This reverts commit 23ceb5b771.
Conflicts:
fs/partitions/check.c
Add an API that tells the other side that callbacks
should be delayed until a lot of work has been done.
Implement using the new event_idx feature.
Note: it might seem advantageous to let the drivers
ask for a callback after a specific capacity has
been reached. However, as a single head can
free many entries in the descriptor table,
we don't really have a clue about capacity
until get_buf is called. The API is the simplest
to implement at the moment, we'll see what kind of
hints drivers can pass when there's more than one
user of the feature.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
With the new used_event and avail_event and features, both
host and guest need similar logic to check whether events are
enabled, so it helps to put the common code in the header.
Note that Xen has similar logic for notification hold-off
in include/xen/interface/io/ring.h with req_event and req_prod
corresponding to event_idx + 1 and new_idx respectively.
+1 comes from the fact that req_event and req_prod in Xen start at 1,
while event index in virtio starts at 0.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Define a new feature bit for the guest and host to utilize
an event index (like Xen) instead if a flag bit to enable/disable
interrupts and kicks.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's unclear to me if it's important, but it's obviously causing my
technical colleages some headaches and I'd hate such imprecision to
slow virtio adoption.
I've emailed this to all non-trivial contributors for approval, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
Acked-by: john cooper <john.cooper@redhat.com>
Acked-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Thomas Gleixner reports that we now have a boot crash triggered by
CONFIG_CPUMASK_OFFSTACK=y:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c11ae035>] find_next_bit+0x55/0xb0
Call Trace:
[<c11addda>] cpumask_any_but+0x2a/0x70
[<c102396b>] flush_tlb_mm+0x2b/0x80
[<c1022705>] pud_populate+0x35/0x50
[<c10227ba>] pgd_alloc+0x9a/0xf0
[<c103a3fc>] mm_init+0xec/0x120
[<c103a7a3>] mm_alloc+0x53/0xd0
which was introduced by commit de03c72cfc ("mm: convert
mm->cpu_vm_cpumask into cpumask_var_t"), and is due to wrong ordering of
mm_init() vs mm_init_cpumask
Thomas wrote a patch to just fix the ordering of initialization, but I
hate the new double allocation in the fork path, so I ended up instead
doing some more radical surgery to clean it all up.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.40' of git://linux-nfs.org/~bfields/linux: (22 commits)
nfsd: make local functions static
NFSD: Remove unused variable from nfsd4_decode_bind_conn_to_session()
NFSD: Check status from nfsd4_map_bcts_dir()
NFSD: Remove setting unused variable in nfsd_vfs_read()
nfsd41: error out on repeated RECLAIM_COMPLETE
nfsd41: compare request's opcnt with session's maxops at nfsd4_sequence
nfsd v4.1 lOCKT clientid field must be ignored
nfsd41: add flag checking for create_session
nfsd41: make sure nfs server process OPEN with EXCLUSIVE4_1 correctly
nfsd4: fix wrongsec handling for PUTFH + op cases
nfsd4: make fh_verify responsibility of nfsd_lookup_dentry caller
nfsd4: introduce OPDESC helper
nfsd4: allow fh_verify caller to skip pseudoflavor checks
nfsd: distinguish functions of NFSD_MAY_* flags
svcrpc: complete svsk processing on cb receive failure
svcrpc: take advantage of tcp autotuning
SUNRPC: Don't wait for full record to receive tcp data
svcrpc: copy cb reply instead of pages
svcrpc: close connection if client sends short packet
svcrpc: note network-order types in svc_process_calldir
...
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm kcopyd: return client directly and not through a pointer
dm kcopyd: reserve fewer pages
dm io: use fixed initial mempool size
dm kcopyd: alloc pages from the main page allocator
dm kcopyd: add gfp parm to alloc_pl
dm kcopyd: remove superfluous page allocation spinlock
dm kcopyd: preallocate sub jobs to avoid deadlock
dm kcopyd: avoid pointless job splitting
dm mpath: do not fail paths after integrity errors
dm table: reject devices without request fns
dm table: allow targets to support discards internally
* 'nfs-for-2.6.40' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Support for RPC over AF_LOCAL transports
SUNRPC: Remove obsolete comment
SUNRPC: Use AF_LOCAL for rpcbind upcalls
SUNRPC: Clean up use of curly braces in switch cases
NFS: Revert NFSROOT default mount options
SUNRPC: Rename xs_encode_tcp_fragment_header()
nfs,rcu: convert call_rcu(nfs_free_delegation_callback) to kfree_rcu()
nfs41: Correct offset for LAYOUTCOMMIT
NFS: nfs_update_inode: print current and new inode size in debug output
NFSv4.1: Fix the handling of NFS4ERR_SEQ_MISORDERED errors
NFSv4: Handle expired stateids when the lease is still valid
SUNRPC: Deal with the lack of a SYN_SENT sk->sk_state_change callback...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI EC: remove redundant code
ACPI: Add D3 cold state
ACPI: processor: fix processor_physically_present in UP kernel
ACPI: Split out custom_method functionality into an own driver
ACPI: Cleanup custom_method debug stuff
ACPI EC: enable MSI workaround for Quanta laptops
ACPICA: Update to version 20110413
ACPICA: Execute an orphan _REG method under the EC device
ACPICA: Move ACPI_NUM_PREDEFINED_REGIONS to a more appropriate place
ACPICA: Update internal address SpaceID for DataTable regions
ACPICA: Add more methods eligible for NULL package element removal
ACPICA: Split all internal Global Lock functions to new file - evglock
ACPI: EC: add another DMI check for ASUS hardware
ACPI EC: remove dead code
ACPICA: Fix code divergence of global lock handling
ACPICA: Use acpi_os_create_lock interface
ACPI: osl, add acpi_os_create_lock interface
ACPI:Fix goto flows in thermal-sys
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
x86 idle: deprecate mwait_idle() and "idle=mwait" cmdline param
x86 idle: deprecate "no-hlt" cmdline param
x86 idle APM: deprecate CONFIG_APM_CPU_IDLE
x86 idle floppy: deprecate disable_hlt()
x86 idle: EXPORT_SYMBOL(default_idle, pm_idle) only when APM demands it
x86 idle: clarify AMD erratum 400 workaround
idle governor: Avoid lock acquisition to read pm_qos before entering idle
cpuidle: menu: fixed wrapping timers at 4.294 seconds
NFSv4.1 LAYOUTRETURN implementation
Currently, does not support layout-type payload encoding.
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Dean Hildebrand <dhildeb@us.ibm.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: Zhang Jingwang <zhangjingwang@nrchpc.ac.cn>
[call pnfs_return_layout right before pnfs_destroy_layout]
[remove assert_spin_locked from pnfs_clear_lseg_list]
[remove wait parameter from the layoutreturn path.]
[remove return_type field from nfs4_layoutreturn_args]
[remove range from nfs4_layoutreturn_args]
[no need to send layoutcommit from _pnfs_return_layout]
[don't wait on sync layoutreturn]
[fix layout stateid in layoutreturn args]
[fixed NULL deref in _pnfs_return_layout]
[removed recaim member of nfs4_layoutreturn_args]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Non-rpc layout driver such as for objects and blocks
implement their own I/O path and error handling logic.
Therefore bypass NFS-based error handling for these layout drivers.
[fix lseg ref-count bugs, and null de-refs]
[Fall out from: non-rpc layout drivers]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
[get rid of PNFS_USE_RPC_CODE]
[get rid of __nfs4_write_done_cb]
[revert useless change in nfs4_write_done_cb]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
* Add the pnfs_osd_xdr.h header
* defintions the pnfs_osd_layout structure including all it's
sub-types and constants.
* Declare the pnfs_osd_xdr_decode_layout API + all needed
inline helpers.
* Define the pnfs_osd_deviceaddr structure and all its subtypes and
constants.
* Declare API for decoding of a pnfs_osd_deviceaddr from XDR stream.
* Define the pnfs_osd_ioerr structure, its substructures and constants.
* Declare API for encoding of a pnfs_osd_ioerr into XDR stream.
* Define the pnfs_osd_layoutupdate structure and its substructures.
* Declare API for encoding of a pnfs_osd_layoutupdate into XDR stream.
[Remove server definitions]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Return client directly from dm_kcopyd_client_create, not through a
parameter, making it consistent with dm_io_client_create.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reserve just the minimum of pages needed to process one job.
Because we allocate pages from page allocator, we don't need to reserve
a large number of pages. The maximum job size is SUB_JOB_SIZE and we
calculate the number of reserved pages based on this.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Replace the arbitrary calculation of an initial io struct mempool size
with a constant.
The code calculated the number of reserved structures based on the request
size and used a "magic" multiplication constant of 4. This patch changes
it to reserve a fixed number - itself still chosen quite arbitrarily.
Further testing might show if there is a better number to choose.
Note that if there is no memory pressure, we can still allocate an
arbitrary number of "struct io" structures. One structure is enough to
process the whole request.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Permit a target to support discards regardless of whether or not all its
underlying devices do.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
page_get_storage_key() and page_set_storage_key() expect a page address
and not its page frame number. This got inconsistent with 2d42552d
"[S390] merge page_test_dirty and page_clear_dirty".
Result is that we read/write storage keys from random pages and do not
have a working dirty bit tracking at all.
E.g. SetPageUpdate() doesn't clear the dirty bit of requested pages, which
for example ext4 doesn't like very much and panics after a while.
Unable to handle kernel paging request at virtual user address (null)
Oops: 0004 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 1 Not tainted 2.6.39-07551-g139f37f-dirty #152
Process flush-94:0 (pid: 1576, task: 000000003eb34538, ksp: 000000003c287b70)
Krnl PSW : 0704c00180000000 0000000000316b12 (jbd2_journal_file_inode+0x10e/0x138)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 EA:3
Krnl GPRS: 0000000000000000 0000000000000000 0000000000000000 0700000000000000
0000000000316a62 000000003eb34cd0 0000000000000025 000000003c287b88
0000000000000001 000000003c287a70 000000003f1ec678 000000003f1ec000
0000000000000000 000000003e66ec00 0000000000316a62 000000003c287988
Krnl Code: 0000000000316b04: f0a0000407f4 srp 4(11,%r0),2036,0
0000000000316b0a: b9020022 ltgr %r2,%r2
0000000000316b0e: a7740015 brc 7,316b38
>0000000000316b12: e3d0c0000024 stg %r13,0(%r12)
0000000000316b18: 4120c010 la %r2,16(%r12)
0000000000316b1c: 4130d060 la %r3,96(%r13)
0000000000316b20: e340d0600004 lg %r4,96(%r13)
0000000000316b26: c0e50002b567 brasl %r14,36d5f4
Call Trace:
([<0000000000316a62>] jbd2_journal_file_inode+0x5e/0x138)
[<00000000002da13c>] mpage_da_map_and_submit+0x2e8/0x42c
[<00000000002daac2>] ext4_da_writepages+0x2da/0x504
[<00000000002597e8>] writeback_single_inode+0xf8/0x268
[<0000000000259f06>] writeback_sb_inodes+0xd2/0x18c
[<000000000025a700>] writeback_inodes_wb+0x80/0x168
[<000000000025aa92>] wb_writeback+0x2aa/0x324
[<000000000025abde>] wb_do_writeback+0xd2/0x274
[<000000000025ae3a>] bdi_writeback_thread+0xba/0x1c4
[<00000000001737be>] kthread+0xa6/0xb0
[<000000000056c1da>] kernel_thread_starter+0x6/0xc
[<000000000056c1d4>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<0000000000316a8a>] jbd2_journal_file_inode+0x86/0x138
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
_SxW returns an Integer containing the lowest D-state supported in state
Sx. If OSPM has not indicated that it supports _PR3, then the value “3”
corresponds to D3. If it has indicated _PR3 support, the value “3”
represents D3hot and the value “4” represents D3cold.
Linux does set _OSC._PR3, so we should fix it to expect that _SxW can
return 4.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Usually, there are multiple processors defined in ACPI table, for
example
Scope (_PR)
{
Processor (CPU0, 0x00, 0x00000410, 0x06) {}
Processor (CPU1, 0x01, 0x00000410, 0x06) {}
Processor (CPU2, 0x02, 0x00000410, 0x06) {}
Processor (CPU3, 0x03, 0x00000410, 0x06) {}
}
processor_physically_present(...) will be called to check whether those
processors are physically present.
Currently we have below codes in processor_physically_present,
cpuid = acpi_get_cpuid(...);
if ((cpuid == -1) && (num_possible_cpus() > 1))
return false;
return true;
In UP kernel, acpi_get_cpuid(...) always return -1 and
num_possible_cpus() always return 1, so
processor_physically_present(...) always returns true for all passed in
processor handles.
This is wrong for UP processor or SMP processor running UP kernel.
This patch removes the !SMP version of acpi_get_cpuid(), so both UP and
SMP kernel use the same acpi_get_cpuid function.
And for UP kernel, only processor 0 is valid.
https://bugzilla.kernel.org/show_bug.cgi?id=16548https://bugzilla.kernel.org/show_bug.cgi?id=16357
Tested-by: Anton Kochkov <anton.kochkov@gmail.com>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Thanks to the reviews and comments by Rafael, James, Mark and Andi.
Here's version 2 of the patch incorporating your comments and also some
update to my previous patch comments.
I noticed that before entering idle state, the menu idle governor will
look up the current pm_qos target value according to the list of qos
requests received. This look up currently needs the acquisition of a
lock to access the list of qos requests to find the qos target value,
slowing down the entrance into idle state due to contention by multiple
cpus to access this list. The contention is severe when there are a lot
of cpus waking and going into idle. For example, for a simple workload
that has 32 pair of processes ping ponging messages to each other, where
64 cpu cores are active in test system, I see the following profile with
37.82% of cpu cycles spent in contention of pm_qos_lock:
- 37.82% swapper [kernel.kallsyms] [k]
_raw_spin_lock_irqsave
- _raw_spin_lock_irqsave
- 95.65% pm_qos_request
menu_select
cpuidle_idle_call
- cpu_idle
99.98% start_secondary
A better approach will be to cache the updated pm_qos target value so
reading it does not require lock acquisition as in the patch below.
With this patch the contention for pm_qos_lock is removed and I saw a
2.2X increase in throughput for my message passing workload.
cc: stable@kernel.org
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Acked-by: mark gross <markgross@thegnar.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (36 commits)
Cache xattr security drop check for write v2
fs: block_page_mkwrite should wait for writeback to finish
mm: Wait for writeback when grabbing pages to begin a write
configfs: remove unnecessary dentry_unhash on rmdir, dir rename
fat: remove unnecessary dentry_unhash on rmdir, dir rename
hpfs: remove unnecessary dentry_unhash on rmdir, dir rename
minix: remove unnecessary dentry_unhash on rmdir, dir rename
fuse: remove unnecessary dentry_unhash on rmdir, dir rename
coda: remove unnecessary dentry_unhash on rmdir, dir rename
afs: remove unnecessary dentry_unhash on rmdir, dir rename
affs: remove unnecessary dentry_unhash on rmdir, dir rename
9p: remove unnecessary dentry_unhash on rmdir, dir rename
ncpfs: fix rename over directory with dangling references
ncpfs: document dentry_unhash usage
ecryptfs: remove unnecessary dentry_unhash on rmdir, dir rename
hostfs: remove unnecessary dentry_unhash on rmdir, dir rename
hfsplus: remove unnecessary dentry_unhash on rmdir, dir rename
hfs: remove unnecessary dentry_unhash on rmdir, dir rename
omfs: remove unnecessary dentry_unhash on rmdir, dir rneame
udf: remove unnecessary dentry_unhash from rmdir, dir rename
...
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, asm: Clean up desc.h a bit
x86, amd: Do not enable ARAT feature on AMD processors below family 0x12
x86: Move do_page_fault()'s error path under unlikely()
x86, efi: Retain boot service code until after switching to virtual mode
x86: Remove unnecessary check in detect_ht()
x86: Reorder mm_context_t to remove x86_64 alignment padding and thus shrink mm_struct
x86, UV: Clean up uv_tlb.c
x86, UV: Add support for SGI UV2 hub chip
x86, cpufeature: Update CPU feature RDRND to RDRAND
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Start RCU kthreads in TASK_INTERRUPTIBLE state
rcu: Remove waitqueue usage for cpu, node, and boost kthreads
rcu: Avoid acquiring rcu_node locks in timer functions
atomic: Add atomic_or()
Documentation: Add statistics about nested locks
rcu: Decrease memory-barrier usage based on semi-formal proof
rcu: Make rcu_enter_nohz() pay attention to nesting
rcu: Don't do reschedule unless in irq
rcu: Remove old memory barriers from rcu_process_callbacks()
rcu: Add memory barriers
rcu: Fix unpaired rcu_irq_enter() from locking selftests
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
perf: Fix SIGIO handling
perf top: Don't stop if no kernel symtab is found
perf top: Handle kptr_restrict
perf top: Remove unused macro
perf events: initialize fd array to -1 instead of 0
perf tools: Make sure kptr_restrict warnings fit 80 col terms
perf tools: Fix build on older systems
perf symbols: Handle /proc/sys/kernel/kptr_restrict
perf: Remove duplicate headers
ftrace: Add internal recursive checks
tracing: Update btrfs's tracepoints to use u64 interface
tracing: Add __print_symbolic_u64 to avoid warnings on 32bit machine
ftrace: Set ops->flag to enabled even on static function tracing
tracing: Have event with function tracer check error return
ftrace: Have ftrace_startup() return failure code
jump_label: Check entries limit in __jump_label_update
ftrace/recordmcount: Avoid STT_FUNC symbols as base on ARM
scripts/tags.sh: Add magic for trace-events for etags too
scripts/tags.sh: Fix ctags for DEFINE_EVENT()
x86/ftrace: Fix compiler warning in ftrace.c
...
* 'for-usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
Intel xhci: Limit number of active endpoints to 64.
Intel xhci: Ignore spurious successful event.
Intel xhci: Support EHCI/xHCI port switching.
Intel xhci: Add PCI id for Panther Point xHCI host.
xhci: STFU: Be quieter during URB submission and completion.
xhci: STFU: Don't print event ring dequeue pointer.
xhci: STFU: Remove function tracing.
xhci: Don't submit commands when the host is dead.
xhci: Clear stopped_td when Stop Endpoint command completes.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (33 commits)
x86: poll waiting for I/OAT DMA channel status
maintainers: add dma engine tree details
dmaengine: add TODO items for future work on dma drivers
dmaengine: Add API documentation for slave dma usage
dmaengine/dw_dmac: Update maintainer-ship
dmaengine: move link order
dmaengine/dw_dmac: implement pause and resume in dwc_control
dmaengine/dw_dmac: Replace spin_lock* with irqsave variants and enable submission from callback
dmaengine/dw_dmac: Divide one sg to many desc, if sg len is greater than DWC_MAX_COUNT
dmaengine/dw_dmac: set residue as total len in dwc_tx_status if status is !DMA_SUCCESS
dmaengine/dw_dmac: don't call callback routine in case dmaengine_terminate_all() is called
dmaengine: at_hdmac: pause: no need to wait for FIFO empty
pch_dma: modify pci device table definition
pch_dma: Support new device ML7223 IOH
pch_dma: Support I2S for ML7213 IOH
pch_dma: Fix DMA setting issue
pch_dma: modify for checkpatch
pch_dma: fix dma direction issue for ML7213 IOH video-in
dmaengine: at_hdmac: use descriptor chaining help function
dmaengine: at_hdmac: implement pause and resume in atc_control
...
Fix up trivial conflict in drivers/dma/dw_dmac.c
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some recent benchmarking on btrfs showed that a major scaling bottleneck
on large systems on btrfs is currently the xattr lookup on every write.
Why xattr lookup on every write I hear you ask?
write wants to drop suid and security related xattrs that could set o
capabilities for executables. To do that it currently looks up
security.capability on EVERY write (even for non executables) to decide
whether to drop it or not.
In btrfs this causes an additional tree walk, hitting some per file system
locks and quite bad scalability. In a simple read workload on a 8S
system I saw over 90% CPU time in spinlocks related to that.
Chris Mason tells me this is also a problem in ext4, where it hits
the global mbcache lock.
This patch adds a simple per inode to avoid this problem. We only
do the lookup once per file and then if there is no xattr cache
the decision. All xattr changes clear the flag.
I also used the same flag to avoid the suid check, although
that one is pretty cheap.
A file system can also set this flag when it creates the inode,
if it has a cheap way to do so. This is done for some common file systems
in followon patches.
With this patch a major part of the lock contention disappears
for btrfs. Some testing on smaller systems didn't show significant
performance changes, but at least it helps the larger systems
and is generally more efficient.
v2: Rename is_sgid. add file system helper.
Cc: chris.mason@oracle.com
Cc: josef@redhat.com
Cc: viro@zeniv.linux.org.uk
Cc: agruen@linbit.com
Cc: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
An atomic_or() function is needed by TREE_RCU to avoid deadlock, so
add a generic version.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The rule is, we have to update tsk->rt.nr_cpus_allowed if we change
tsk->cpus_allowed. Otherwise RT scheduler may confuse.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4DD4B3FA.5060901@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
TI-RPC introduces the capability of performing RPC over AF_LOCAL
sockets. It uses this mainly for registering and unregistering
local RPC services securely with the local rpcbind, but we could
also conceivably use it as a generic upcall mechanism.
This patch provides a client-side only implementation for the moment.
We might also consider a server-side implementation to provide
AF_LOCAL access to NLM (for statd downcalls, and such like).
Autobinding is not supported on kernel AF_LOCAL transports at this
time. Kernel ULPs must specify the pathname of the remote endpoint
when an AF_LOCAL transport is created. rpcbind supports registering
services available via AF_LOCAL, so the kernel could handle it with
some adjustment to ->rpcbind and ->set_port. But we don't need this
feature for doing upcalls via well-known named sockets.
This has not been tested with ULPs that move a substantial amount of
data. Thus, I can't attest to how robust the write_space and
congestion management logic is.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Kill ratelimit.h dependency in linux/net.h
net: Add linux/sysctl.h includes where needed.
net: Kill ether_table[] declaration.
inetpeer: fix race in unused_list manipulations
atm: expose ATM device index in sysfs
IPVS: bug in ip_vs_ftp, same list heaad used in all netns.
bug.h: Move ratelimit warn interfaces to ratelimit.h
bonding: cleanup module option descriptions
net:8021q:vlan.c Fix pr_info to just give the vlan fullname and version.
net: davinci_emac: fix dev_err use at probe
can: convert to %pK for kptr_restrict support
net: fix ETHTOOL_SFEATURES compatibility with old ethtool_ops.set_flags
netfilter: Fix several warnings in compat_mtw_from_user().
netfilter: ipset: fix ip_set_flush return code
netfilter: ipset: remove unused variable from type_pf_tdel()
netfilter: ipset: Use proper timeout value to jiffies conversion
Ingo Molnar noticed that we have this unnecessary ratelimit.h
dependency in linux/net.h, which hid compilation problems from
people doing builds only with CONFIG_NET enabled.
Move this stuff out to a seperate net/net_ratelimit.h file and
include that in the only two places where this thing is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Several networking headers were depending upon the implicit
linux/sysctl.h include they get when including linux/net.h
Add explicit includes.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'docs-move' of git://git.kernel.org/pub/scm/linux/kernel/git/rdunlap/linux-docs:
Create Documentation/security/, move LSM-, credentials-, and keys-related files from Documentation/ to Documentation/security/, add Documentation/security/00-INDEX, and update all occurrences of Documentation/<moved_file> to Documentation/security/<moved_file>.
