Pull x86 vdso updates from Ingo Molnar:
"Further simplifications and improvements to the VDSO code, by Andy
Lutomirski"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64/vsyscall: Fix warn_bad_vsyscall log output
x86/vdso: Set VM_MAYREAD for the vvar vma
x86, vdso: Get rid of the fake section mechanism
x86, vdso: Move the vvar area before the vdso text
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle are:
- RAS tracing/events infrastructure, by Gong Chen.
- Various generalizations of the APEI code to make it available to
non-x86 architectures, by Tomasz Nowicki"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ras: Fix build warnings in <linux/aer.h>
acpi, apei, ghes: Factor out ioremap virtual memory for IRQ and NMI context.
acpi, apei, ghes: Make NMI error notification to be GHES architecture extension.
apei, mce: Factor out APEI architecture specific MCE calls.
RAS, extlog: Adjust init flow
trace, eMCA: Add a knob to adjust where to save event log
trace, RAS: Add eMCA trace event interface
RAS, debugfs: Add debugfs interface for RAS subsystem
CPER: Adjust code flow of some functions
x86, MCE: Robustify mcheck_init_device
trace, AER: Move trace into unified interface
trace, RAS: Add basic RAS trace event
x86, MCE: Kill CPU_POST_DEAD
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle are:
- Intel SOC driver updates, by Aubrey Li.
- TS5500 platform updates, by Vivien Didelot"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pmc_atom: Silence shift wrapping warnings in pmc_sleep_tmr_show()
x86/pmc_atom: Expose PMC device state and platform sleep state
x86/pmc_atom: Eisable a few S0ix wake up events for S0ix residency
x86/platform: New Intel Atom SOC power management controller driver
x86/platform/ts5500: Add support for TS-5400 boards
x86/platform/ts5500: Add a 'name' sysfs attribute
x86/platform/ts5500: Use the DEVICE_ATTR_RO() macro
Pull x86 mm changes from Ingo Molnar:
"The main change in this cycle is the rework of the TLB range flushing
code, to simplify, fix and consolidate the code. By Dave Hansen"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Set TLB flush tunable to sane value (33)
x86/mm: New tunable for single vs full TLB flush
x86/mm: Add tracepoints for TLB flushes
x86/mm: Unify remote INVLPG code
x86/mm: Fix missed global TLB flush stat
x86/mm: Rip out complicated, out-of-date, buggy TLB flushing
x86/mm: Clean up the TLB flushing code
x86/smep: Be more informative when signalling an SMEP fault
Pull EFI changes from Ingo Molnar:
"Main changes in this cycle are:
- arm64 efi stub fixes, preservation of FP/SIMD registers across
firmware calls, and conversion of the EFI stub code into a static
library - Ard Biesheuvel
- Xen EFI support - Daniel Kiper
- Support for autoloading the efivars driver - Lee, Chun-Yi
- Use the PE/COFF headers in the x86 EFI boot stub to request that
the stub be loaded with CONFIG_PHYSICAL_ALIGN alignment - Michael
Brown
- Consolidate all the x86 EFI quirks into one file - Saurabh Tangri
- Additional error logging in x86 EFI boot stub - Ulf Winkelvos
- Support loading initrd above 4G in EFI boot stub - Yinghai Lu
- EFI reboot patches for ACPI hardware reduced platforms"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
efi/arm64: Handle missing virtual mapping for UEFI System Table
arch/x86/xen: Silence compiler warnings
xen: Silence compiler warnings
x86/efi: Request desired alignment via the PE/COFF headers
x86/efi: Add better error logging to EFI boot stub
efi: Autoload efivars
efi: Update stale locking comment for struct efivars
arch/x86: Remove efi_set_rtc_mmss()
arch/x86: Replace plain strings with constants
xen: Put EFI machinery in place
xen: Define EFI related stuff
arch/x86: Remove redundant set_bit(EFI_MEMMAP) call
arch/x86: Remove redundant set_bit(EFI_SYSTEM_TABLES) call
efi: Introduce EFI_PARAVIRT flag
arch/x86: Do not access EFI memory map if it is not available
efi: Use early_mem*() instead of early_io*()
arch/ia64: Define early_memunmap()
x86/reboot: Add EFI reboot quirk for ACPI Hardware Reduced flag
efi/reboot: Allow powering off machines using EFI
efi/reboot: Add generic wrapper around EfiResetSystem()
...
Pull x86 cpufeature updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued cleanups of CPU bugs mis-marked as 'missing features', by
Borislav Petkov.
- Detect the xsaves/xrstors feature and releated cleanup, by Fenghua
Yu"
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Kill cpu_has_mp
x86, amd: Cleanup init_amd
x86/cpufeature: Add bug flags to /proc/cpuinfo
x86, cpufeature: Convert more "features" to bugs
x86/xsaves: Detect xsaves/xrstors feature
x86/cpufeature.h: Reformat x86 feature macros
Pull x86 build/cleanup/debug updates from Ingo Molnar:
"Robustify the build process with a quirk to avoid GCC reordering
related bugs.
Two code cleanups.
Simplify entry_64.S CFI annotations, by Jan Beulich"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, build: Change code16gcc.h from a C header to an assembly header
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Simplify __HAVE_ARCH_CMPXCHG tests
x86/tsc: Get rid of custom DIV_ROUND() macro
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Drop several unnecessary CFI annotations
Pull perf changes from Ingo Molnar:
"Kernel side changes:
- Consolidate the PMU interrupt-disabled code amongst architectures
(Vince Weaver)
- misc fixes
Tooling changes (new features, user visible changes):
- Add support for pagefault tracing in 'trace', please see multiple
examples in the changeset messages (Stanislav Fomichev).
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add header for columns in 'top' and 'report' TUI browsers (Jiri
Olsa)
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add IO mode into timechart command (Stanislav Fomichev)
- Fallback to syscalls:* when raw_syscalls:* is not available in the
perl and python perf scripts. (Daniel Bristot de Oliveira)
- Add --repeat global option to 'perf bench' to be used in benchmarks
such as the existing 'futex' one, that was modified to use it
instead of a local option. (Davidlohr Bueso)
- Fix fd -> pathname resolution in 'trace', be it using /proc or a
vfs_getname probe point. (Arnaldo Carvalho de Melo)
- Add suggestion of how to set perf_event_paranoid sysctl, to help
non-root users trying tools like 'trace' to get a working
environment. (Arnaldo Carvalho de Melo)
- Updates from trace-cmd for traceevent plugin_kvm plus args cleanup
(Steven Rostedt, Jan Kiszka)
- Support S/390 in 'perf kvm stat' (Alexander Yarygin)
Tooling infrastructure changes:
- Allow reserving a row for header purposes in the hists browser
(Arnaldo Carvalho de Melo)
- Various fixes and prep work related to supporting Intel PT (Adrian
Hunter)
- Introduce multiple debug variables control (Jiri Olsa)
- Add callchain and additional sample information for python scripts
(Joseph Schuchart)
- More prep work to support Intel PT: (Adrian Hunter)
- Polishing 'script' BTS output
- 'inject' can specify --kallsym
- VDSO is per machine, not a global var
- Expose data addr lookup functions previously private to 'script'
- Large mmap fixes in events processing
- Include standard stringify macros in power pc code (Sukadev
Bhattiprolu)
Tooling cleanups:
- Convert open coded equivalents to asprintf() (Andy Shevchenko)
- Remove needless reassignments in 'trace' (Arnaldo Carvalho de Melo)
- Cache the is_exit syscall test in 'trace) (Arnaldo Carvalho de
Melo)
- No need to reimplement err() in 'perf bench sched-messaging', drop
barf(). (Davidlohr Bueso).
- Remove ev_name argument from perf_evsel__hists_browse, can be
obtained from the other parameters. (Jiri Olsa)
Tooling fixes:
- Fix memory leak in the 'sched-messaging' perf bench test.
(Davidlohr Bueso)
- The -o and -n 'perf bench mem' options are mutually exclusive, emit
error when both are specified. (Davidlohr Bueso)
- Fix scrollbar refresh row index in the ui browser, problem exposed
now that headers will be added and will be allowed to be switched
on/off. (Jiri Olsa)
- Handle the num array type in python properly (Sebastian Andrzej
Siewior)
- Fix wrong condition for allocation failure (Jiri Olsa)
- Adjust callchain based on DWARF debug info on powerpc (Sukadev
Bhattiprolu)
- Fix a risk for doing free on uninitialized pointer in traceevent
lib (Rickard Strandqvist)
- Update attr test with PERF_FLAG_FD_CLOEXEC flag (Jiri Olsa)
- Enable close-on-exec flag on perf file descriptor (Yann Droneaud)
- Fix build on gcc 4.4.7 (Arnaldo Carvalho de Melo)
- Event ordering fixes (Jiri Olsa)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (123 commits)
Revert "perf tools: Fix jump label always changing during tracing"
perf tools: Fix perf usage string leftover
perf: Check permission only for parent tracepoint event
perf record: Store PERF_RECORD_FINISHED_ROUND only for nonempty rounds
perf record: Always force PERF_RECORD_FINISHED_ROUND event
perf inject: Add --kallsyms parameter
perf tools: Expose 'addr' functions so they can be reused
perf session: Fix accounting of ordered samples queue
perf powerpc: Include util/util.h and remove stringify macros
perf tools: Fix build on gcc 4.4.7
perf tools: Add thread parameter to vdso__dso_findnew()
perf tools: Add dso__type()
perf tools: Separate the VDSO map name from the VDSO dso name
perf tools: Add vdso__new()
perf machine: Fix the lifetime of the VDSO temporary file
perf tools: Group VDSO global variables into a structure
perf session: Add ability to skip 4GiB or more
perf session: Add ability to 'skip' a non-piped event stream
perf tools: Pass machine to vdso__dso_findnew()
perf tools: Add dso__data_size()
...
to the ftrace function callback infrastructure. It's introducing a
way to allow different functions to call directly different trampolines
instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which always
had a different trampoline, but the function tracer trampoline was called
and did basically nothing, and then the function graph tracer trampoline
was called. The difference now, is that the function graph tracer
trampoline can be called directly if a function is only being traced by
the function graph trampoline. If function tracing is also happening on
the same function, the old way is still done.
The accounting for this takes up more memory when function graph tracing
is activated, as it needs to keep track of which functions it uses.
I have a new way that wont take as much memory, but it's not ready yet
for this merge window, and will have to wait for the next one.
Another big change was the removal of the ftrace_start/stop() calls that
were used by the suspend/resume code that stopped function tracing when
entering into suspend and resume paths. The stop of ftrace was done
because there was some function that would crash the system if one called
smp_processor_id()! The stop/start was a big hammer to solve the issue
at the time, which was when ftrace was first introduced into Linux.
Now ftrace has better infrastructure to debug such issues, and I found
the problem function and labeled it with "notrace" and function tracing
can now safely be activated all the way down into the guts of suspend
and resume.
Other changes include clean ups of uprobe code.
Clean up of the trace_seq() code.
And other various small fixes and clean ups to ftrace and tracing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT35zXAAoJEKQekfcNnQGuOz0H/38zqM0nLFhrgvz3EPk2UOjn
xqpX8qyb2V7TJZL+IqeXU2a5cQZl5ba0D4WtBGpxbTae3CJYiuQ87iKUNFoH0om5
FDpn80igb368k8V3qRdRsziKVCCf0XBd/NkHJXc0ZkfXGyzB2Ga4bBxALxp2gj9y
bnO+vKo6+tWYKG4hyQb4P3LRXUrK8/LWEsPr39cH2QH1Rdj69Lx9CgrCdUVJmwcb
Bj8hEiLXL/RYCFNn79A3wNTUvW0rG/AOIf4SLqXtasSRZ0ToaU0ZyDnrNv+0Ol47
rX8tSk+LfXchL9hpIvjCf1vlAYq3pO02favteR/jip3lx/dTjEDE4RJ9qtJzZ4Q=
=fwQY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
I don't know if we really need 64 bits here but these variables are
declared as u64 and it can't hurt to cast this so we prevent any shift
wrapping.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/20140801082715.GE28869@mwanda
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
I think the flush_tlb_mm_range() code that tries to tune the
flush sizes based on the CPU needs to get ripped out for
several reasons:
1. It is obviously buggy. It uses mm->total_vm to judge the
task's footprint in the TLB. It should certainly be using
some measure of RSS, *NOT* ->total_vm since only resident
memory can populate the TLB.
2. Haswell, and several other CPUs are missing from the
intel_tlb_flushall_shift_set() function. Thus, it has been
demonstrated to bitrot quickly in practice.
3. It is plain wrong in my vm:
[ 0.037444] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.037444] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.037444] tlb_flushall_shift: 6
Which leads to it to never use invlpg.
4. The assumptions about TLB refill costs are wrong:
http://lkml.kernel.org/r/1337782555-8088-3-git-send-email-alex.shi@intel.com
(more on this in later patches)
5. I can not reproduce the original data: https://lkml.org/lkml/2012/5/17/59
I believe the sample times were too short. Running the
benchmark in a loop yields times that vary quite a bit.
Note that this leaves us with a static ceiling of 1 page. This
is a conservative, dumb setting, and will be revised in a later
patch.
This also removes the code which attempts to predict whether we
are flushing data or instructions. We expect instruction flushes
to be relatively rare and not worth tuning for explicitly.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154055.ABC88E89@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The primary dependency is that GHES uses the x86 NMI for hardware
error notification and MCE for memory error handling. These patches
remove that dependency.
Other APEI features such as error reporting via external IRQ, error
serialization, or error injection, do not require changes to use them
on non-x86 architectures.
The following patch set eliminates the APEI Kconfig x86 dependency
by making these changes:
- treat NMI notification as GHES architecture - HAVE_ACPI_APEI_NMI
- group and wrap around #ifdef CONFIG_HAVE_ACPI_APEI_NMI code which
is used only for NMI path
- identify architectural boxes and abstract it accordingly (tlb flush and MCE)
- rework ioremap for both IRQ and NMI context
NMI code is kept in ghes.c file since NMI and IRQ context are tightly coupled.
Note, these patches introduce no functional changes for x86. The NMI notification
feature is hard selected for x86. Architectures that want to use this
feature should also provide NMI code infrastructure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nYdd
-----END PGP SIGNATURE-----
Merge tag 'please-pull-apei' into x86/ras
APEI is currently implemented so that it depends on x86 hardware.
The primary dependency is that GHES uses the x86 NMI for hardware
error notification and MCE for memory error handling. These patches
remove that dependency.
Other APEI features such as error reporting via external IRQ, error
serialization, or error injection, do not require changes to use them
on non-x86 architectures.
The following patch set eliminates the APEI Kconfig x86 dependency
by making these changes:
- treat NMI notification as GHES architecture - HAVE_ACPI_APEI_NMI
- group and wrap around #ifdef CONFIG_HAVE_ACPI_APEI_NMI code which
is used only for NMI path
- identify architectural boxes and abstract it accordingly (tlb flush and MCE)
- rework ioremap for both IRQ and NMI context
NMI code is kept in ghes.c file since NMI and IRQ context are tightly coupled.
Note, these patches introduce no functional changes for x86. The NMI notification
feature is hard selected for x86. Architectures that want to use this
feature should also provide NMI code infrastructure.
This moves the espfix64 logic into native_iret. To make this work,
it gets rid of the native patch for INTERRUPT_RETURN:
INTERRUPT_RETURN on native kernels is now 'jmp native_iret'.
This changes the 16-bit SS behavior on Xen from OOPSing to leaking
some bits of the Xen hypervisor's RSP (I think).
[ hpa: this is a nonzero cost on native, but probably not enough to
measure. Xen needs to fix this in their own code, probably doing
something equivalent to espfix64. ]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/7b8f1d8ef6597cb16ae004a43c56980a7de3cf94.1406129132.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT1VYNAAoJEHm+PkMAQRiGQJwIAKSYp1Uqz5O/e5r0V1TlZKT4
1B4Njopl57PwSrJQWcGEuH2yHyM896vfPO4L6BJIOfyWzh8kwpQqclDt6uhXoF/v
OsO1zb/7/j+n/pDZsePqP9AyIgErsHEBgUbhecDqzjN++ITPcZjQ6TIMPglZaumN
jFAdAZuAaEwqAk8jqN2wlm689Fh9MuUEarHXbXLCqu5RgLrWhFGhp/cTWY62aqnZ
XfEeQ9KtpRZmlR/IYjerbb1eRH7ZdJsZ88WngLX9dj/JdNxHWBkWQBXGAusXk5Fk
y6LsIV3TjyBdrRKJ1Ifyg/2EIXHNBs8HxTFGXpjtp2HPuMLDxZOWOWikb9URtNg=
=Fjf4
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc7' into perf/core, to merge in the latest fixes before applying new changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf fixes from Thomas Gleixner:
"A bunch of fixes for perf and kprobes:
- revert a commit that caused a perf group regression
- silence dmesg spam
- fix kprobe probing errors on ia64 and ppc64
- filter kprobe faults from userspace
- lockdep fix for perf exit path
- prevent perf #GP in KVM guest
- correct perf event and filters"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Fix "Failed to find blacklist" probing errors on ia64 and ppc64
kprobes/x86: Don't try to resolve kprobe faults from userspace
perf/x86/intel: Avoid spamming kernel log for BTS buffer failure
perf/x86/intel: Protect LBR and extra_regs against KVM lying
perf: Fix lockdep warning on process exit
perf/x86/intel/uncore: Fix SNB-EP/IVT Cbox filter mappings
perf/x86/intel: Use proper dTLB-load-misses event on IvyBridge
perf: Revert ("perf: Always destroy groups on exit")
This commit in Linux 3.6:
commit c767a54ba0
Author: Joe Perches <joe@perches.com>
Date: Mon May 21 19:50:07 2012 -0700
x86/debug: Add KERN_<LEVEL> to bare printks, convert printks to pr_<level>
caused warn_bad_vsyscall to output garbage in the middle of the
line. Revert the bad part of it.
The printk in question isn't actually bare; the level is "%s".
The bug this fixes is purely cosmetic; backports are optional.
Cc: <stable@vger.kernel.org> # v3.6+
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/03eac1f24110bbe496ecc12a4df467e0d88466d4.1406330947.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add the following interfaces to exposes PMC device state and sleep
state residency via debugfs:
/sys/kernel/debugfs/pmc_atom/dev_state
/sys/kernel/debugfs/pmc_atom/sleep_state
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/53B0FF59.8000600@linux.intel.com
Signed-off-by: Kasagar, Srinidhi <srinidhi.kasagar@intel.com>
Reviewed-by: Rudramuni, Vishwesh M <vishwesh.m.rudramuni@intel.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Disable PMC S0IX_WAKE_EN events coming from LPC block(unused) and
also from GPIO_SUS ored dedicated IRQs (must be disabled as per PMC
programming rule), GPIOSCORE ored dedicated IRQs (must be disabled
as per PMC programming rule), GPIO_SUS shared IRQ (not necessary
since the IOAPIC_DS wake event will still work), GPIO_SCORE shared
IRQ (not necessary since the IOAPIC_DS wake event will still work).
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/53B0FF22.5080403@linux.intel.com
Signed-off-by: Olivier Leveque <olivier.leveque@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The Power Management Controller (PMC) controls many of the power
management features present in the Atom SoC. This driver provides
a native power off function via PMC PCI IO port.
On some ACPI hardware-reduced platforms(e.g. ASUS-T100), ACPI sleep
registers are not valid so that (*pm_power_off)() is not hooked by
acpi_power_off(). The power off function in this driver is installed
only when pm_power_off is NULL.
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/53B0FEEA.3010805@linux.intel.com
Signed-off-by: Lejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This fix was necessary after
9c15a24b03 ("x86/mce: Improve mcheck_init_device() error handling")
went in. What this patch did was, among others, check the return value
of misc_register and exit early if it encountered an error. Original
code sloppily didn't do that.
However,
cef12ee52b ("xen/mce: Add mcelog support for Xen platform")
made it so that xen's init routine xen_late_init_mcelog runs first. This
was needed for the xen mcelog device which is supposed to be independent
from the baremetal one.
Initially it was reported that misc_register() fails often on xen and
that's why it needed fixing. However, it is *supposed* to fail by
design, when running in dom0 so that the xen mcelog device file gets
registered first.
And *then* you need the notifier *not* unregistered on the error path so
that the timer does get deleted properly in the CPU hotplug notifier.
Btw, this fix is needed also on baremetal in the unlikely event that
misc_register(&mce_chrdev_device) fails there too.
I was unsure whether to rush it in now and decided to delay it to 3.17.
However, xen people wanted it promoted as it breaks xen when doing cpu
hotplug there. So, after a bit of simmering in tip/master for initial
smoke testing, let's move it to 3.16. It fixes a semi-regression which
got introduced in 3.16 so no need for stable tagging.
tip/x86/ras contains that exact same commit but we can't remove it
there as it is not the last one. It won't cause any merge issues, as I
confirmed locally but I should state here the special situation of this
one fix explicitly anyway.
Thanks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z/P/
-----END PGP SIGNATURE-----
x86: Merge tag 'ras_urgent' into x86/urgent
Promote one fix for 3.16
This fix was necessary after
9c15a24b03 ("x86/mce: Improve mcheck_init_device() error handling")
went in. What this patch did was, among others, check the return value
of misc_register and exit early if it encountered an error. Original
code sloppily didn't do that.
However,
cef12ee52b ("xen/mce: Add mcelog support for Xen platform")
made it so that xen's init routine xen_late_init_mcelog runs first. This
was needed for the xen mcelog device which is supposed to be independent
from the baremetal one.
Initially it was reported that misc_register() fails often on xen and
that's why it needed fixing. However, it is *supposed* to fail by
design, when running in dom0 so that the xen mcelog device file gets
registered first.
And *then* you need the notifier *not* unregistered on the error path so
that the timer does get deleted properly in the CPU hotplug notifier.
Btw, this fix is needed also on baremetal in the unlikely event that
misc_register(&mce_chrdev_device) fails there too.
I was unsure whether to rush it in now and decided to delay it to 3.17.
However, xen people wanted it promoted as it breaks xen when doing cpu
hotplug there. So, after a bit of simmering in tip/master for initial
smoke testing, let's move it to 3.16. It fixes a semi-regression which
got introduced in 3.16 so no need for stable tagging.
tip/x86/ras contains that exact same commit but we can't remove it
there as it is not the last one. It won't cause any merge issues, as I
confirmed locally but I should state here the special situation of this
one fix explicitly anyway.
Thanks.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
P4 systems with cpuid level < 4 can have SMT, but the cache topology
description available (cpuid2) does not include SMP information.
Now we know that SMT shares all cache levels, and therefore we can
mark all available cache levels as shared.
We do this by setting cpu_llc_id to ->phys_proc_id, since that's
the same for each SMT thread. We can do this unconditional since if
there's no SMT its still true, the one CPU shares cache with only
itself.
This fixes a problem where such CPUs report an incorrect LLC CPU mask.
This in turn fixes a crash in the scheduler where the topology was
build wrong, it assumes the LLC mask to include at least the SMT CPUs.
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140722133514.GM12054@laptop.lan
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
GHES currently maps two pages with atomic_ioremap. From now
on, NMI is architectural depended so there is no need to allocate
an NMI page for platforms without NMI support.
To make it possible to not use a second page, swap the existing
page order so that the IRQ context page is first, and the optional
NMI context page is second. Then, use HAVE_ACPI_APEI_NMI to decide
how many pages are to be allocated.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This commit abstracts MCE calls and provides weak corresponding default
implementation for those architectures which do not need arch specific
actions. Each platform willing to do additional architectural actions
should provides desired function definition. It allows us to avoid wrap
code into #ifdef in generic code and prevent new platform from introducing
dummy stub function too.
Initially, there are two APEI arch-specific calls:
- arch_apei_enable_cmcff()
- arch_apei_report_mem_error()
Both interact with MCE driver for X86 architecture.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Commit 554086d ("x86_32, entry: Do syscall exit work on badsys
(CVE-2014-4508)") introduced a regression in the x86_32 syscall entry
code, resulting in syscall() not returning proper errors for undefined
syscalls on CPUs supporting the sysenter feature.
The following code:
> int result = syscall(666);
> printf("result=%d errno=%d error=%s\n", result, errno, strerror(errno));
results in:
> result=666 errno=0 error=Success
Obviously, the syscall return value is the called syscall number, but it
should have been an ENOSYS error. When run under ptrace it behaves
correctly, which makes it hard to debug in the wild:
> result=-1 errno=38 error=Function not implemented
The %eax register is the return value register. For debugging via ptrace
the syscall entry code stores the complete register context on the
stack. The badsys handlers only store the ENOSYS error code in the
ptrace register set and do not set %eax like a regular syscall handler
would. The old resume_userspace call chain contains code that clobbers
%eax and it restores %eax from the ptrace registers afterwards. The same
goes for the ptrace-enabled call chain. When ptrace is not used, the
syscall return value is the passed-in syscall number from the untouched
%eax register.
Use %eax as the return value register in syscall_badsys and
sysenter_badsys, like a real syscall handler does, and have the caller
push the value onto the stack for ptrace access.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.11.1407221022380.31021@titan.int.lan.stealer.net
Reviewed-and-tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: <stable@vger.kernel.org> # If 554086d is backported
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
BorisO reports that misc_register() fails often on xen. The current code
unregisters the CPU hotplug notifier in that case. If then a CPU is
offlined and onlined back again, we end up with a second timer running
on that CPU, leading to soft lockups and system hangs.
So let's leave the hotcpu notifier always registered - even if
mce_device_create failed for some cores and never unreg it so that we
can deal with the timer handling accordingly.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1403274493-1371-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull x86 fixes from Peter Anvin:
"A couple of key fixes and a few less critical ones. The main ones
are:
- add a .bss section to the PE/COFF headers when building with EFI
stub
- invoke the correct paravirt magic when building the espfix page
tables
Unfortunately both of these areas also have at least one additional
fix each still in thie pipeline, but which are not yet ready to push"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove unused variable "polling"
x86/espfix/xen: Fix allocation of pages for paravirt page tables
x86/efi: Include a .bss section within the PE/COFF headers
efi: fdt: Do not report an error during boot if UEFI is not available
efi/arm64: efistub: remove local copy of linux_banner
We've got constants, so let's use them instead of hard-coded values.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
It appears that the BayTrail-T class of hardware requires EFI in order
to powerdown and reboot and no other reliable method exists.
This quirk is generally applicable to all hardware that has the ACPI
Hardware Reduced bit set, since usually ACPI would be the preferred
method.
Cc: Len Brown <len.brown@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Implement efi_reboot(), which is really just a wrapper around the
EfiResetSystem() EFI runtime service, but it does at least allow us to
funnel all callers through a single location.
It also simplifies the callsites since users no longer need to check to
see whether EFI_RUNTIME_SERVICES are enabled.
Cc: Tony Luck <tony.luck@intel.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Nothing sets function_trace_stop to disable function tracing anymore.
Remove the check for it in the arch code.
Link: http://lkml.kernel.org/r/53C54D32.6000000@zytor.com
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_stop() is going away as it disables parts of function tracing
that affects users that should not be affected. But ftrace_graph_stop()
is built on ftrace_stop(). Here's another example of killing all of
function tracing because something went wrong with function graph
tracing.
Instead of disabling all users of function tracing on function graph
error, disable only function graph tracing. To do this, the arch code
must call ftrace_graph_is_dead() before it implements function graph.
Link: http://lkml.kernel.org/r/53C54D18.3020602@zytor.com
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull perf fixes from Ingo Molnar:
"Tooling fixes and an Intel PMU driver fixlet"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Do not allow optimized switch for non-cloned events
perf/x86/intel: ignore CondChgd bit to avoid false NMI handling
perf symbols: Get kernel start address by symbol name
perf tools: Fix segfault in cumulative.callchain report
Commit 30919b0bf3 ("x86: avoid low BIOS area when allocating address
space") moved the test for resource allocations that fall within the first
1MB of address space from the PCI-specific path to a generic path, such
that all resource allocations will avoid this area. However, this breaks
ISA cards which need to allocate a memory region within the first 1MB. An
example is the i82365 PCMCIA controller and derivatives like the Ricoh
RF5C296/396 which map part of the PCMCIA socket memory address space into
the first 1MB of system memory address space. They do not work anymore as
no usable memory region exists due to this change:
Intel ISA PCIC probe: Ricoh RF5C296/396 ISA-to-PCMCIA at port 0x3e0 ofs 0x00, 2 sockets
host opts [0]: none
host opts [1]: none
ISA irqs (scanned) = 3,4,5,9,10 status change on irq 10
pcmcia_socket pcmcia_socket1: pccard: PCMCIA card inserted into slot 1
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3ff: excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f 0x3c0-0x3e7 0x3f0-0x3ff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0a0000-0x0affff: excluding 0xa0000-0xaffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0b0000-0x0bffff: excluding 0xb0000-0xbffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0cffff: excluding 0xc0000-0xcbfff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0d0000-0x0dffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0e0000-0x0effff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3ff: excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f 0x3c0-0x3e7 0x3f0-0x3ff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0a0000-0x0affff: excluding 0xa0000-0xaffff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0b0000-0x0bffff: excluding 0xb0000-0xbffff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0cffff: excluding 0xc0000-0xcbfff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0d0000-0x0dffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0e0000-0x0effff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0cc000-0x0effff: excluding 0xe0000-0xeffff
pcmcia_socket pcmcia_socket1: cs: unable to map card memory!
If filtering out the first 1MB is reverted, everything works as expected.
Tested-by: Robert Resch <fli4l@robert.reschpara.de>
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v2.6.37+
With the conversion of the register saving code from macros to
functions, and with those functions not clobbering most of the
registers they spill, there's no need to annotate most of the
spill operations; the only exceptions being %rbx (always
modified) and %rcx (modified on the error_kernelspace: path).
Also remove a bogus commented out annotation - there's no
register %orig_rax after all.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/53AAE69A020000780001D3C7@mail.emea.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This commit:
commit 6f6343f53d
Author: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Date: Thu Apr 17 17:17:33 2014 +0900
kprobes/x86: Call exception handlers directly from do_int3/do_debug
appears to have inadvertently dropped a check that the int3 came
from kernel mode. Trying to dereference addr when addr is
user-controlled is completely bogus.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/c4e339882c121aa76254f2adde3fcbdf502faec2.1405099506.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It's unnecessary to excessively spam the kernel log anytime the BTS buffer
cannot be allocated, so make this allocation __GFP_NOWARN.
The user probably will want to at least find some artifact that the
allocation has failed in the past, probably due to fragmentation because
of its large size, when it's not allocated at bootstrap. Thus, add a
WARN_ONCE() so something is left behind for them to understand why perf
commnads that require PEBS is not working properly.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1406301600460.26302@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
According to Peter's advice, put the failure handling to a goto chain.
Compiled in x86_64, could you check if there is anything that I missed.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1402459743-20513-1-git-send-email-zhouzhouyi@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With -cpu host, KVM reports LBR and extra_regs support, if the host has
support.
When the guest perf driver tries to access LBR or extra_regs MSR,
it #GPs all MSR accesses,since KVM doesn't handle LBR and extra_regs support.
So check the related MSRs access right once at initialization time to avoid
the error access at runtime.
For reproducing the issue, please build the kernel with CONFIG_KVM_INTEL = y
(for host kernel).
And CONFIG_PARAVIRT = n and CONFIG_KVM_GUEST = n (for guest kernel).
Start the guest with -cpu host.
Run perf record with --branch-any or --branch-filter in guest to trigger LBR
Run perf stat offcore events (E.g. LLC-loads/LLC-load-misses ...) in guest to
trigger offcore_rsp #GP
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maria Dimakopoulou <maria.n.dimakopoulou@gmail.com>
Cc: Mark Davies <junk@eslaf.co.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yan, Zheng <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1405365957-20202-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fixes the SNB-EP and IVT Cbox filter mapping
table. The table controls which filters are supported by
which events. There were several mistakes in those tables
causing some filters to be ignored, such as NID on
TOR_INSERTS.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: zheng.z.yan@intel.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140630144624.GA2604@quad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This was discussed back in February:
https://lkml.org/lkml/2014/2/18/956
But I never saw a patch come out of it.
On IvyBridge we share the SandyBridge cache event tables, but the
dTLB-load-miss event is not compatible. Patch it up after
the fact to the proper DTLB_LOAD_MISSES.DEMAND_LD_MISS_CAUSES_A_WALK
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1407141528200.17214@vincent-weaver-1.umelst.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
init_espfix_ap() is currently off by one level when informing hypervisor
that allocated pages will be used for ministacks' page tables.
The most immediate effect of this on a PV guest is that if
'stack_page = __get_free_page()' returns a non-zeroed-out page the hypervisor
will refuse to use it for a page table (which it shouldn't be anyway). This will
result in warnings by both Xen and Linux.
More importantly, a subsequent write to that page (again, by a PV guest) is
likely to result in fatal page fault.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1404926298-5565-1-git-send-email-boris.ostrovsky@oracle.com
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Distribute family-specific code to corresponding functions.
Also,
* move the direct mapping splitting around the TSEG SMM area to
bsp_init_amd().
* kill ancient comment about what we should do for K5.
* merge amd_k7_smp_check() into its only caller init_amd_k7 and drop
cpu_has_mp macro.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1403609105-8332-3-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
