Also renamed struct fib6_walker_t to fib6_walker and enum fib_walk_state_t
to fib6_walk_state as recommended by Cong Wang.
Cc: Cong Wang <cwang@twopensource.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains another batch with Netfilter/IPVS updates
for net-next, they are:
1) Add abstracted ICMP codes to the nf_tables reject expression. We
introduce four reasons to reject using ICMP that overlap in IPv4
and IPv6 from the semantic point of view. This should simplify the
maintainance of dual stack rule-sets through the inet table.
2) Move nf_send_reset() functions from header files to per-family
nf_reject modules, suggested by Patrick McHardy.
3) We have to use IS_ENABLED(CONFIG_BRIDGE_NETFILTER) everywhere in the
code now that br_netfilter can be modularized. Convert remaining spots
in the network stack code.
4) Use rcu_barrier() in the nf_tables module removal path to ensure that
we don't leave object that are still pending to be released via
call_rcu (that may likely result in a crash).
5) Remove incomplete arch 32/64 compat from nft_compat. The original (bad)
idea was to probe the word size based on the xtables match/target info
size, but this assumption is wrong when you have to dump the information
back to userspace.
6) Allow to filter from prerouting and postrouting in the nf_tables bridge.
In order to emulate the ebtables NAT chains (which are actually simple
filter chains with no special semantics), we have support filtering from
this hooks too.
7) Add explicit module dependency between xt_physdev and br_netfilter.
This provides a way to detect if the user needs br_netfilter from
the configuration path. This should reduce the breakage of the
br_netfilter modularization.
8) Cleanup coding style in ip_vs.h, from Simon Horman.
9) Fix crash in the recently added nf_tables masq expression. We have
to register/unregister the notifiers to clean up the conntrack table
entries from the module init/exit path, not from the rule addition /
deletion path. From Arturo Borrero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes fou[46]_gro_receive and fou[46]_gro_complete
functions. The v4 or v6 variants were chosen for the UDP offloads
based on the address family of the socket this is not necessary
or correct. Alternatively, this patch adds is_ipv6 to napi_gro_skb.
This is set in udp6_gro_receive and unset in udp4_gro_receive. In
fou_gro_receive the value is used to select the correct inet_offloads
for the protocol of the outer IP header.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to register the notifiers in the masquerade expression from
the the module _init and _exit path.
This fixes crashes when removing the masquerade rule with no
ipt_MASQUERADE support in place (which was masking the problem).
Fixes: 9ba1f72 ("netfilter: nf_tables: add new nft_masq expression")
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In 34666d4 ("netfilter: bridge: move br_netfilter out of the core"),
the bridge netfilter code has been modularized.
Use IS_ENABLED instead of ifdef to cover the module case.
Fixes: 34666d4 ("netfilter: bridge: move br_netfilter out of the core")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move nf_send_reset() and nf_send_reset6() to nf_reject_ipv4 and
nf_reject_ipv6 respectively. This code is shared by x_tables and
nf_tables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Call skb_set_inner_protocol to set inner Ethernet protocol to
protocol being encapsulation by GRE before tunnel_xmit. This is
needed for GSO if UDP encapsulation (fou) is being done.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_ipproto to set inner IP protocol to IPPROTO_IPV6
before tunnel_xmit. This is needed if UDP encapsulation (fou) is
being done.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_udp_segment is the function called from udp4_ufo_fragment to
segment a UDP tunnel packet. This function currently assumes
segmentation is transparent Ethernet bridging (i.e. VXLAN
encapsulation). This patch generalizes the function to
operate on either Ethertype or IP protocol.
The inner_protocol field must be set to the protocol of the inner
header. This can now be either an Ethertype or an IP protocol
(in a union). A new flag in the skbuff indicates which type is
effective. skb_set_inner_protocol and skb_set_inner_ipproto
helper functions were added to set the inner_protocol. These
functions are called from the point where the tunnel encapsulation
is occuring.
When skb_udp_tunnel_segment is called, the function to segment the
inner packet is selected based on the inner IP or Ethertype. In the
case of an IP protocol encapsulation, the function is derived from
inet[6]_offloads. In the case of Ethertype, skb->protocol is
set to the inner_protocol and skb_mac_gso_segment is called. (GRE
currently does this, but it might be possible to lookup the protocol
in offload_base and call the appropriate segmenation function
directly).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.
Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).
I verified via tracing that this change has effect.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
pull request: netfilter/ipvs updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
most relevantly they are:
1) Four patches to make the new nf_tables masquerading support
independent of the x_tables infrastructure. This also resolves a
compilation breakage if the masquerade target is disabled but the
nf_tables masq expression is enabled.
2) ipset updates via Jozsef Kadlecsik. This includes the addition of the
skbinfo extension that allows you to store packet metainformation in the
elements. This can be used to fetch and restore this to the packets through
the iptables SET target, patches from Anton Danilov.
3) Add the hash:mac set type to ipset, from Jozsef Kadlecsick.
4) Add simple weighted fail-over scheduler via Simon Horman. This provides
a fail-over IPVS scheduler (unlike existing load balancing schedulers).
Connections are directed to the appropriate server based solely on
highest weight value and server availability, patch from Kenny Mathis.
5) Support IPv6 real servers in IPv4 virtual-services and vice versa.
Simon Horman informs that the motivation for this is to allow more
flexibility in the choice of IP version offered by both virtual-servers
and real-servers as they no longer need to match: An IPv4 connection
from an end-user may be forwarded to a real-server using IPv6 and
vice versa. No ip_vs_sync support yet though. Patches from Alex Gartrell
and Julian Anastasov.
6) Add global generation ID to the nf_tables ruleset. When dumping from
several different object lists, we need a way to identify that an update
has ocurred so userspace knows that it needs to refresh its lists. This
also includes a new command to obtain the 32-bits generation ID. The
less significant 16-bits of this ID is also exposed through res_id field
in the nfnetlink header to quickly detect the interference and retry when
there is no risk of ID wraparound.
7) Move br_netfilter out of the bridge core. The br_netfilter code is
built in the bridge core by default. This causes problems of different
kind to people that don't want this: Jesper reported performance drop due
to the inconditional hook registration and I remember to have read complains
on netdev from people regarding the unexpected behaviour of our bridging
stack when br_netfilter is enabled (fragmentation handling, layer 3 and
upper inspection). People that still need this should easily undo the
damage by modprobing the new br_netfilter module.
8) Dump the set policy nf_tables that allows set parameterization. So
userspace can keep user-defined preferences when saving the ruleset.
From Arturo Borrero.
9) Use __seq_open_private() helper function to reduce boiler plate code
in x_tables, From Rob Jones.
10) Safer default behaviour in case that you forget to load the protocol
tracker. Daniel Borkmann and Florian Westphal detected that if your
ruleset is stateful, you allow traffic to at least one single SCTP port
and the SCTP protocol tracker is not loaded, then any SCTP traffic may
be pass through unfiltered. After this patch, the connection tracking
classifies SCTP/DCCP/UDPlite/GRE packets as invalid if your kernel has
been compiled with support for these modules.
====================
Trivially resolved conflict in include/linux/skbuff.h, Eric moved some
netfilter skbuff members around, and the netfilter tree adjusted the
ifdef guards for the bridging info pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2014-09-25
1) Remove useless hash_resize_mutex in xfrm_hash_resize().
This mutex is used only there, but xfrm_hash_resize()
can't be called concurrently at all. From Ying Xue.
2) Extend policy hashing to prefixed policies based on
prefix lenght thresholds. From Christophe Gouault.
3) Make the policy hash table thresholds configurable
via netlink. From Christophe Gouault.
4) Remove the maximum authentication length for AH.
This was needed to limit stack usage. We switched
already to allocate space, so no need to keep the
limit. From Herbert Xu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP maintains lists of skb in write queue, and in receive queues
(in order and out of order queues)
Scanning these lists both in input and output path usually requires
access to skb->next, TCP_SKB_CB(skb)->seq, and TCP_SKB_CB(skb)->end_seq
These fields are currently in two different cache lines, meaning we
waste lot of memory bandwidth when these queues are big and flows
have either packet drops or packet reorders.
We can move TCP_SKB_CB(skb)->header at the end of TCP_SKB_CB, because
this header is not used in fast path. This allows TCP to search much faster
in the skb lists.
Even with regular flows, we save one cache line miss in fast path.
Thanks to Christoph Paasch for noticing we need to cleanup
skb->cb[] (IPCB/IP6CB) before entering IP stack in tx path,
and that I forgot IPCB use in tcp_v4_hnd_req() and tcp_v4_save_options().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_opt_accepted() assumes IP6CB(skb) holds the struct inet6_skb_parm
that it needs. Lets not assume this, as TCP stack might use a different
place.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6gre_tunnel_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vti6_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_tnl_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this alias, we don't need to load manually the module before adding an
ip6gretap interface with iproute2.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The send_check logic was only interesting in cases of TCP offload and
UDP UFO where the checksum needed to be initialized to the pseudo
header checksum. Now we've moved that logic into the related
gso_segment functions so gso_send_check is no longer needed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In udp[46]_ufo_send_check the UDP checksum initialized to the pseudo
header checksum. We can move this logic into udp[46]_ufo_fragment.
After this change udp[64]_ufo_send_check is a no-op.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp_v[46]_gso_send_check the TCP checksum is initialized to the
pseudo header checksum using __tcp_v[46]_send_check. We can move this
logic into new tcp[46]_gso_segment functions to be done when
ip_summed != CHECKSUM_PARTIAL (ip_summed == CHECKSUM_PARTIAL should be
the common case, possibly always true when taking GSO path). After this
change tcp_v[46]_gso_send_check is no-op.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ICMP rate limiting uses inetpeer cache, which is an RBL tree
protected by a lock, meaning that hosts can be stuck hard if all cpus
want to check ICMP limits.
When say a DNS or NTP server process is restarted, inetpeer tree grows
quick and machine comes to its knees.
iptables can not help because the bottleneck happens before ICMP
messages are even cooked and sent.
This patch adds a new global limitation, using a token bucket filter,
controlled by two new sysctl :
icmp_msgs_per_sec - INTEGER
Limit maximal number of ICMP packets sent per second from this host.
Only messages whose type matches icmp_ratemask are
controlled by this limit.
Default: 1000
icmp_msgs_burst - INTEGER
icmp_msgs_per_sec controls number of ICMP packets sent per second,
while icmp_msgs_burst controls the burst size of these packets.
Default: 50
Note that if we really want to send millions of ICMP messages per
second, we might extend idea and infra added in commit 04ca6973f7
("ip: make IP identifiers less predictable") :
add a token bucket in the ip_idents hash and no longer rely on inetpeer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC2710 (MLDv1), section 3.7. says:
The length of a received MLD message is computed by taking the
IPv6 Payload Length value and subtracting the length of any IPv6
extension headers present between the IPv6 header and the MLD
message. If that length is greater than 24 octets, that indicates
that there are other fields present *beyond* the fields described
above, perhaps belonging to a *future backwards-compatible* version
of MLD. An implementation of the version of MLD specified in this
document *MUST NOT* send an MLD message longer than 24 octets and
MUST ignore anything past the first 24 octets of a received MLD
message.
RFC3810 (MLDv2), section 8.2.1. states for *listeners* regarding
presence of MLDv1 routers:
In order to be compatible with MLDv1 routers, MLDv2 hosts MUST
operate in version 1 compatibility mode. [...] When Host
Compatibility Mode is MLDv2, a host acts using the MLDv2 protocol
on that interface. When Host Compatibility Mode is MLDv1, a host
acts in MLDv1 compatibility mode, using *only* the MLDv1 protocol,
on that interface. [...]
While section 8.3.1. specifies *router* behaviour regarding presence
of MLDv1 routers:
MLDv2 routers may be placed on a network where there is at least
one MLDv1 router. The following requirements apply:
If an MLDv1 router is present on the link, the Querier MUST use
the *lowest* version of MLD present on the network. This must be
administratively assured. Routers that desire to be compatible
with MLDv1 MUST have a configuration option to act in MLDv1 mode;
if an MLDv1 router is present on the link, the system administrator
must explicitly configure all MLDv2 routers to act in MLDv1 mode.
When in MLDv1 mode, the Querier MUST send periodic General Queries
truncated at the Multicast Address field (i.e., 24 bytes long),
and SHOULD also warn about receiving an MLDv2 Query (such warnings
must be rate-limited). The Querier MUST also fill in the Maximum
Response Delay in the Maximum Response Code field, i.e., the
exponential algorithm described in section 5.1.3. is not used. [...]
That means that we should not get queries from different versions of
MLD. When there's a MLDv1 router present, MLDv2 enforces truncation
and MRC == MRD (both fields are overlapping within the 24 octet range).
Section 8.3.2. specifies behaviour in the presence of MLDv1 multicast
address *listeners*:
MLDv2 routers may be placed on a network where there are hosts
that have not yet been upgraded to MLDv2. In order to be compatible
with MLDv1 hosts, MLDv2 routers MUST operate in version 1 compatibility
mode. MLDv2 routers keep a compatibility mode per multicast address
record. The compatibility mode of a multicast address is determined
from the Multicast Address Compatibility Mode variable, which can be
in one of the two following states: MLDv1 or MLDv2.
The Multicast Address Compatibility Mode of a multicast address
record is set to MLDv1 whenever an MLDv1 Multicast Listener Report is
*received* for that multicast address. At the same time, the Older
Version Host Present timer for the multicast address is set to Older
Version Host Present Timeout seconds. The timer is re-set whenever a
new MLDv1 Report is received for that multicast address. If the Older
Version Host Present timer expires, the router switches back to
Multicast Address Compatibility Mode of MLDv2 for that multicast
address. [...]
That means, what can happen is the following scenario, that hosts can
act in MLDv1 compatibility mode when they previously have received an
MLDv1 query (or, simply operate in MLDv1 mode-only); and at the same
time, an MLDv2 router could start up and transmits MLDv2 startup query
messages while being unaware of the current operational mode.
Given RFC2710, section 3.7 we would need to answer to that with an MLDv1
listener report, so that the router according to RFC3810, section 8.3.2.
would receive that and internally switch to MLDv1 compatibility as well.
Right now, I believe since the initial implementation of MLDv2, Linux
hosts would just silently drop such MLDv2 queries instead of replying
with an MLDv1 listener report, which would prevent a MLDv2 router going
into fallback mode (until it receives other MLDv1 queries).
Since the mapping of MRC to MRD in exactly such cases can make use of
the exponential algorithm from 5.1.3, we cannot [strictly speaking] be
aware in MLDv1 of the encoding in MRC, it seems also not mentioned by
the RFC. Since encodings are the same up to 32767, assume in such a
situation this value as a hard upper limit we would clamp. We have asked
one of the RFC authors on that regard, and he mentioned that there seem
not to be any implementations that make use of that exponential algorithm
on startup messages. In any case, this patch fixes this MLD
interoperability issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unable to load various tunneling modules without this:
[ 80.679049] fou: Unknown symbol udp_sock_create6 (err 0)
[ 91.439939] ip6_udp_tunnel: Unknown symbol ip6_local_out (err 0)
[ 91.439954] ip6_udp_tunnel: Unknown symbol __put_net (err 0)
[ 91.457792] vxlan: Unknown symbol udp_sock_create6 (err 0)
[ 91.457831] vxlan: Unknown symbol udp_tunnel6_xmit_skb (err 0)
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions supplied in ip6_udp_tunnel.c are only needed when IPV6 is
selected. When IPV6 is not selected, those functions are stubbed out
in udp_tunnel.h.
==================================================================
net/ipv6/ip6_udp_tunnel.c:15:5: error: redefinition of 'udp_sock_create6'
int udp_sock_create6(struct net *net, struct udp_port_cfg *cfg,
In file included from net/ipv6/ip6_udp_tunnel.c:9:0:
include/net/udp_tunnel.h:36:19: note: previous definition of 'udp_sock_create6' was here
static inline int udp_sock_create6(struct net *net, struct udp_port_cfg *cfg,
==================================================================
Fixes: fd384412e udp_tunnel: Seperate ipv6 functions into its own file
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added netlink handling of IP tunnel encapulation paramters, properly
adjust MTU for encapsulation. Added ip_tunnel_encap call to
ipip6_tunnel_xmit to actually perform FOU encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Want to be able to use these in foo-over-udp offloads, etc.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a few more UDP tunnel APIs that can be shared by UDP based
tunnel protocol implementation. The main ones are highlighted below.
setup_udp_tunnel_sock() configures UDP listener socket for
receiving UDP encapsulated packets.
udp_tunnel_xmit_skb() and upd_tunnel6_xmit_skb() transmit skb
using UDP encapsulation.
udp_tunnel_sock_release() closes the UDP tunnel listener socket.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip6_udp_tunnel.c for ipv6 UDP tunnel functions to avoid ifdefs
in udp_tunnel.c
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While tracking down the MAX_AH_AUTH_LEN crash in an old kernel
I thought that this limit was rather arbitrary and we should
just get rid of it.
In fact it seems that we've already done all the work needed
to remove it apart from actually removing it. This limit was
there in order to limit stack usage. Since we've already
switched over to allocating scratch space using kmalloc, there
is no longer any need to limit the authentication length.
This patch kills all references to it, including the BUG_ONs
that led me here.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently we genarate a blackhole route route whenever we have
matching policies but can not resolve the states. Here we assume
that dst_output() is called to kill the balckholed packets.
Unfortunately this assumption is not true in all cases, so
it is possible that these packets leave the system unwanted.
We fix this by generating blackhole routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: 2774c131b1 ("xfrm: Handle blackhole route creation via afinfo.")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Input path of TCP do not currently uses TCP_SKB_CB(skb)->tcp_flags,
which is only used in output path.
tcp_recvmsg(), looks at tcp_hdr(skb)->syn for every skb found in receive queue,
and its unfortunate because this bit is located in a cache line right before
the payload.
We can simplify TCP by copying tcp flags into TCP_SKB_CB(skb)->tcp_flags.
This patch does so, and avoids the cache line miss in tcp_recvmsg()
Following patches will
- allow a segment with FIN being coalesced in tcp_try_coalesce()
- simplify tcp_collapse() by not copying the headers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If IPv6 is explicitly disabled before the interface comes up,
it makes no sense to continue when it comes up, even just
print a message.
(I am not sure about other cases though, so I prefer not to touch)
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor out allocation and initialization and make
the refcount code more readable.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly the code is already protected by rtnl lock.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly the code is already protected by rtnl lock.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor out allocation and initialization and make
the refcount code more readable.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it accept inet6_dev, and rename it to __ipv6_dev_ac_inc()
to reflect this change.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just move rtnl lock up, so that the anycast list can be protected
by rtnl lock now.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These code is now protected by rtnl lock, rcu read lock
is useless now.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2abb7cdc0d ("udp: Add support for doing checksum unnecessary
conversion") caused napi_gro_cb structs with the "flush" field zero to
take the "udp_gro_receive" path rather than the "set flush to 1" path
that they would previously take. As a result I saw booting from an NFS
root hang shortly after starting userspace, with "server not
responding" messages.
This change to the handling of "flush == 0" packets appears to be
incidental to the goal of adding new code in the case where
skb_gro_checksum_validate_zero_check() returns zero. Based on that and
the fact that it breaks things, I'm assuming that it is unintentional.
Fixes: 2abb7cdc0d ("udp: Add support for doing checksum unnecessary conversion")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we try to rmmod the driver for an interface while sockets with
setsockopt(JOIN_ANYCAST) are alive, some refcounts aren't cleaned up
and we get stuck on:
unregister_netdevice: waiting for ens3 to become free. Usage count = 1
If we LEAVE_ANYCAST/close everything before rmmod'ing, there is no
problem.
We need to perform a cleanup similar to the one for multicast in
addrconf_ifdown(how == 1).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users are starting to test nf_tables with no x_tables support. Therefore,
masquerading needs to be indenpendent of it from Kconfig.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that we have masquerading support in nf_tables, the NAT chain can
be use with it, not only for SNAT/DNAT. So make this chain type
independent of it.
While at it, move it inside the scope of 'if NF_NAT_IPV*' to simplify
dependencies.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
nf-next pull request
The following patchset contains Netfilter/IPVS updates for your
net-next tree. Regarding nf_tables, most updates focus on consolidating
the NAT infrastructure and adding support for masquerading. More
specifically, they are:
1) use __u8 instead of u_int8_t in arptables header, from
Mike Frysinger.
2) Add support to match by skb->pkttype to the meta expression, from
Ana Rey.
3) Add support to match by cpu to the meta expression, also from
Ana Rey.
4) A smatch warning about IPSET_ATTR_MARKMASK validation, patch from
Vytas Dauksa.
5) Fix netnet and netportnet hash types the range support for IPv4,
from Sergey Popovich.
6) Fix missing-field-initializer warnings resolved, from Mark Rustad.
7) Dan Carperter reported possible integer overflows in ipset, from
Jozsef Kadlecsick.
8) Filter out accounting objects in nfacct by type, so you can
selectively reset quotas, from Alexey Perevalov.
9) Move specific NAT IPv4 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
10) Use the new NAT IPv4 functions from nft_chain_nat_ipv4.
11) Move specific NAT IPv6 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
12) Use the new NAT IPv6 functions from nft_chain_nat_ipv6.
13) Refactor code to add nft_delrule(), which can be reused in the
enhancement of the NFT_MSG_DELTABLE to remove a table and its
content, from Arturo Borrero.
14) Add a helper function to unregister chain hooks, from
Arturo Borrero.
15) A cleanup to rename to nft_delrule_by_chain for consistency with
the new nft_*() functions, also from Arturo.
16) Add support to match devgroup to the meta expression, from Ana Rey.
17) Reduce stack usage for IPVS socket option, from Julian Anastasov.
18) Remove unnecessary textsearch state initialization in xt_string,
from Bojan Prtvar.
19) Add several helper functions to nf_tables, more work to prepare
the enhancement of NFT_MSG_DELTABLE, again from Arturo Borrero.
20) Enhance NFT_MSG_DELTABLE to delete a table and its content, from
Arturo Borrero.
21) Support NAT flags in the nat expression to indicate the flavour,
eg. random fully, from Arturo.
22) Add missing audit code to ebtables when replacing tables, from
Nicolas Dichtel.
23) Generalize the IPv4 masquerading code to allow its re-use from
nf_tables, from Arturo.
24) Generalize the IPv6 masquerading code, also from Arturo.
25) Add the new masq expression to support IPv4/IPv6 masquerading
from nf_tables, also from Arturo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6_gro_receive and ipv6_gro_complete to sit_offload to
support GRO.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In TCP gro we check flush_id which is derived from the IP identifier.
In IPv4 gro path the flush_id is set with the expectation that every
matched packet increments IP identifier. In IPv6, the flush_id is
never set and thus is uinitialized. What's worse is that in IPv6
over IPv4 encapsulation, the IP identifier is taken from the outer
header which is currently not incremented on every packet for Linux
stack, so GRO in this case never matches packets (identifier is
not increasing).
This patch clears flush_id for every time for a matched packet in
IPv6 gro_receive. We need to do this each time to overwrite the
setting that would be done in IPv4 gro_receive per the outer
header in IPv6 over Ipv4 encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
