The PHB diag-data is important to help locating the root cause for
EEH errors such as frozen PE or fenced PHB. However, the EEH core
enables IO path by clearing part of HW registers before collecting
this data causing it to be corrupted.
This patch fixes this by dumping the PHB diag-data immediately when
frozen/fenced state on PE or PHB is detected for the first time in
eeh_ops::get_state() or next_error() backend.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new ELFv2 little-endian ABI increases the stack redzone -- the
area below the stack pointer that can be used for storing data --
from 288 bytes to 512 bytes. This means that we need to allow more
space on the user stack when delivering a signal to a 64-bit process.
To make the code a bit clearer, we define new USER_REDZONE_SIZE and
KERNEL_REDZONE_SIZE symbols in ptrace.h. For now, we leave the
kernel redzone size at 288 bytes, since increasing it to 512 bytes
would increase the size of interrupt stack frames correspondingly.
Gcc currently only makes use of 288 bytes of redzone even when
compiling for the new little-endian ABI, and the kernel cannot
currently be compiled with the new ABI anyway.
In the future, hopefully gcc will provide an option to control the
amount of redzone used, and then we could reduce it even more.
This also changes the code in arch_compat_alloc_user_space() to
preserve the expanded redzone. It is not clear why this function would
ever be used on a 64-bit process, though.
Signed-off-by: Paul Mackerras <paulus@samba.org>
CC: <stable@vger.kernel.org> [v3.13]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The branch target should be the func addr, not the addr of func_descr_t.
So using ppc_function_entry() to generate the right target addr.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In copy_oldmem_page, the current check using max_pfn and min_low_pfn to
decide if the page is backed or not, is not valid when the memory layout is
not continuous.
This happens when running as a QEMU/KVM guest, where RTAS is mapped higher
in the memory. In that case max_pfn points to the end of RTAS, and a hole
between the end of the kdump kernel and RTAS is not backed by PTEs. As a
consequence, the kdump kernel is crashing in copy_oldmem_page when accessing
in a direct way the pages in that hole.
This fix relies on the memblock's service memblock_is_region_memory to
check if the read page is part or not of the directly accessible memory.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we're storing a host endian RTAS token in
rtas_stop_self_args.token. We then pass that directly to rtas. This is
fine on big endian however on little endian the token is not what we
expect.
This will typically result in hitting:
panic("Alas, I survived.\n");
To fix this we always use the stop-self token in host order and always
convert it to be32 before passing this to rtas.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We possiblly detect EEH errors during reboot, particularly in kexec
path, but it's impossible for device drivers and EEH core to handle
or recover them properly.
The patch registers one reboot notifier for EEH and disable EEH
subsystem during reboot. That means the EEH errors is going to be
cleared by hardware reset or second kernel during early stage of
PCI probe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When doing reset in order to recover the affected PE, we issue
hot reset on PE primary bus if it's not root bus. Otherwise, we
issue hot or fundamental reset on root port or PHB accordingly.
For the later case, we didn't cover the situation where PE only
includes root port and it potentially causes kernel crash upon
EEH error to the PE.
The patch reworks the logic of EEH reset to improve the code
readability and also avoid the kernel crash.
Cc: stable@vger.kernel.org
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing a lot of hits in the VDSO that are not resolved by perf.
A while(1) gettimeofday() loop shows the issue:
27.64% [vdso] [.] 0x000000000000060c
22.57% [vdso] [.] 0x0000000000000628
16.88% [vdso] [.] 0x0000000000000610
12.39% [vdso] [.] __kernel_gettimeofday
6.09% [vdso] [.] 0x00000000000005f8
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We are using a stripped VDSO image which means only symbols with
relocation info can be resolved. There isn't a lot of point to
stripping the VDSO, the debug info is only about 1kB:
4680 arch/powerpc/kernel/vdso64/vdso64.so
5815 arch/powerpc/kernel/vdso64/vdso64.so.dbg
By using the unstripped image, we can resolve all the symbols in the
VDSO and the perf profile data looks much better:
76.53% [vdso] [.] __do_get_tspec
12.20% [vdso] [.] __kernel_gettimeofday
5.05% [vdso] [.] __get_datapage
3.20% test [.] main
2.92% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
perf is failing to resolve symbols in the VDSO. A while (1)
gettimeofday() loop shows:
93.99% [vdso] [.] 0x00000000000005e0
3.12% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.81% test [.] main
The reason for this is that we are linking our VDSO shared libraries
at 1MB, which is a little weird. Even though this is uncommon, Alan
points out that it is valid and we should probably fix perf userspace.
Regardless, I can't see a reason why we are doing this. The code
is all position independent and we never rely on the VDSO ending
up at 1M (and we never place it there on 64bit tasks).
Changing our link address to 0x0 fixes perf VDSO symbol resolution:
73.18% [vdso] [.] 0x000000000000060c
12.39% [vdso] [.] __kernel_gettimeofday
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We still have some local symbol resolution issues that will be
fixed in a subsequent patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Archs like ppc64 doesn't do tlb flush in set_pte/pmd functions when using
a hash table MMU for various reasons (the flush is handled as part of
the PTE modification when necessary).
ppc64 thus doesn't implement flush_tlb_range for hash based MMUs.
Additionally ppc64 require the tlb flushing to be batched within ptl locks.
The reason to do that is to ensure that the hash page table is in sync with
linux page table.
We track the hpte index in linux pte and if we clear them without flushing
hash and drop the ptl lock, we can have another cpu update the pte and can
end up with duplicate entry in the hash table, which is fatal.
We also want to keep set_pte_at simpler by not requiring them to do hash
flush for performance reason. We do that by assuming that set_pte_at() is
never *ever* called on a PTE that is already valid.
This was the case until the NUMA code went in which broke that assumption.
Fix that by introducing a new pair of helpers to set _PAGE_NUMA in a
way similar to ptep/pmdp_set_wrprotect(), with a generic implementation
using set_pte_at() and a powerpc specific one using the appropriate
mechanism needed to keep the hash table in sync.
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pte_update() is a powerpc-ism used to change the bits of a PTE
when the access permission is being restricted (a flush is
potentially needed).
It uses atomic operations on when needed and handles the hash
synchronization on hash based processors.
It is currently only used to clear PTE bits and so the current
implementation doesn't provide a way to also set PTE bits.
The new _PAGE_NUMA bit, when set, is actually restricting access
so it must use that function too, so this change adds the ability
for pte_update() to also set bits.
We will use this later to set the _PAGE_NUMA bit.
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rev3 of the PCI Express Base Specification defines a Supported Link
Speeds Vector where the bit definitions within this field are:
Bit 0 - 2.5 GT/s
Bit 1 - 5.0 GT/s
Bit 2 - 8.0 GT/s
This vector definition is used by the platform firmware to export the
maximum and current link speeds of the PCI bus via the
"ibm,pcie-link-speed-stats" device-tree property.
This patch updates pseries_root_bridge_prepare() to detect Gen3
speed buses (defined by 0x04).
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 5091f0c (powerpc/pseries: Fix PCIE link speed endian issue)
introduced a regression on the PCI link speed detection using the
device-tree property. The ibm,pcie-link-speed-stats property is composed
of two 32-bit integers, the first one being the maxinum link speed and
the second the current link speed. The changes introduced by the
aforementioned commit are considering just the first integer.
Fix this issue by changing how the property is accessed, using the
helper functions to properly access the array of values. The explicit
byte swapping is not needed anymore here, since it's done by the helper
functions.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Guenter Roeck has got the following call trace on a p2020 board:
Kernel stack overflow in process eb3e5a00, r1=eb79df90
CPU: 0 PID: 2838 Comm: ssh Not tainted 3.13.0-rc8-juniper-00146-g19eca00 #4
task: eb3e5a00 ti: c0616000 task.ti: ef440000
NIP: c003a420 LR: c003a410 CTR: c0017518
REGS: eb79dee0 TRAP: 0901 Not tainted (3.13.0-rc8-juniper-00146-g19eca00)
MSR: 00029000 <CE,EE,ME> CR: 24008444 XER: 00000000
GPR00: c003a410 eb79df90 eb3e5a00 00000000 eb05d900 00000001 65d87646 00000000
GPR08: 00000000 020b8000 00000000 00000000 44008442
NIP [c003a420] __do_softirq+0x94/0x1ec
LR [c003a410] __do_softirq+0x84/0x1ec
Call Trace:
[eb79df90] [c003a410] __do_softirq+0x84/0x1ec (unreliable)
[eb79dfe0] [c003a970] irq_exit+0xbc/0xc8
[eb79dff0] [c000cc1c] call_do_irq+0x24/0x3c
[ef441f20] [c00046a8] do_IRQ+0x8c/0xf8
[ef441f40] [c000e7f4] ret_from_except+0x0/0x18
--- Exception: 501 at 0xfcda524
LR = 0x10024900
Instruction dump:
7c781b78 3b40000a 3a73b040 543c0024 3a800000 3b3913a0 7ef5bb78 48201bf9
5463103a 7d3b182e 7e89b92e 7c008146 <3ba00000> 7e7e9b78 48000014 57fff87f
Kernel panic - not syncing: kernel stack overflow
CPU: 0 PID: 2838 Comm: ssh Not tainted 3.13.0-rc8-juniper-00146-g19eca00 #4
Call Trace:
The reason is that we have used the wrong register to calculate the
ksp_limit in commit cbc9565ee8 (powerpc: Remove ksp_limit on ppc64).
Just fix it.
As suggested by Benjamin Herrenschmidt, also add the C prototype of the
function in the comment in order to avoid such kind of errors in the
future.
Cc: stable@vger.kernel.org # 3.12
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We expose a number of OF properties in the kexec and crash dump code
and these need to be big endian.
Cc: stable@vger.kernel.org # v3.13
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We would allocate one specific exception stack for each kind of
non-base exceptions for every CPU. For ppc32 the CPU hard ID is
used as the subscript to get the specific exception stack for
one CPU. But for an UP kernel, there is only one element in the
each kind of exception stack array. We would get stuck if the
CPU hard ID is not equal to '0'. So in this case we should use the
subscript '0' no matter what the CPU hard ID is.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we set our cpu's bit in cpus_in_xmon, and then we take the
output lock and print the exception information.
This can race with the master cpu entering the command loop and printing
the backtrace. The result is that the backtrace gets garbled with
another cpu's exception print out.
Fix it by delaying the set of cpus_in_xmon until we are finished
printing.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As far as I can tell, our 70s era timeout loop in get_output_lock() is
generating no code.
This leads to the hostile takeover happening more or less simultaneously
on all cpus. The result is "interesting", some example output that is
more readable than most:
cpu 0x1: Vector: 100 (Scypsut e0mx bR:e setV)e catto xc0p:u[ c 00
c0:0 000t0o0V0erc0td:o5 rfc28050000]0c00 0 0 0 6t(pSrycsV1ppuot
uxe 1m 2 0Rx21e3:0s0ce000c00000t00)00 60602oV2SerucSayt0y 0p 1sxs
Fix it by using udelay() in the timeout loop. The wait time and check
frequency are arbitrary, but seem to work OK. We already rely on
udelay() working so this is not a new dependency.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we enter with xmon_speaker != 0 we skip the first cmpxchg(), we also
skip the while loop because xmon_speaker != last_speaker (0) - meaning we
skip the second cmpxchg() also.
Following that code path the compiler sees no memory barriers and so is
within its rights to never reload xmon_speaker. The end result is we loop
forever.
This manifests as all cpus being in xmon ('c' command), but they refuse
to take control when you switch to them ('c x' for cpu # x).
I have seen this deadlock in practice and also checked the generated code to
confirm this is what's happening.
The simplest fix is just to always try the cmpxchg().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now the config_bhrb() PMU specific call happens after
write_mmcr0(), which actually enables the PMU for event counting and
interrupts. So there is a small window of time where the PMU and BHRB
runs without the required HW branch filter (if any) enabled in BHRB.
This can cause some of the branch samples to be collected through BHRB
without any filter applied and hence affects the correctness of
the results. This patch moves the BHRB config function call before
enabling interrupts.
Here are some data points captured via trace prints which depicts how we
could get PMU interrupts with BHRB filter NOT enabled with a standard
perf record command line (asking for branch record information as well).
$ perf record -j any_call ls
Before the patch:-
ls-1962 [003] d... 2065.299590: .perf_event_interrupt: MMCRA: 40000000000
ls-1962 [003] d... 2065.299603: .perf_event_interrupt: MMCRA: 40000000000
...
All the PMU interrupts before this point did not have the requested
HW branch filter enabled in the MMCRA.
ls-1962 [003] d... 2065.299647: .perf_event_interrupt: MMCRA: 40040000000
ls-1962 [003] d... 2065.299662: .perf_event_interrupt: MMCRA: 40040000000
After the patch:-
ls-1850 [008] d... 190.311828: .perf_event_interrupt: MMCRA: 40040000000
ls-1850 [008] d... 190.311848: .perf_event_interrupt: MMCRA: 40040000000
All the PMU interrupts have the requested HW BHRB branch filter
enabled in MMCRA.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Fixed up whitespace and cleaned up changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a driver for the ARCH_RANDOM hook in rng.c, so we should select
ARCH_RANDOM on pseries.
Without this the build breaks if you turn ARCH_RANDOM off.
This hasn't broken the build because pseries_defconfig doesn't specify a
value for PPC_POWERNV, which is default y, and selects ARCH_RANDOM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Relocation's code is not working in little endian mode because the r_info
field, which is a 64 bits value, should be read from the right offset.
The current code is optimized to read the r_info field as a 32 bits value
starting at the middle of the double word (offset 12). When running in LE
mode, the read value is not correct since only the MSB is read.
This patch removes this optimization which consist to deal with a 32 bits
value instead of a 64 bits one. This way it works in big and little endian
mode.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On p8 systems, with relocation on exception feature enabled we are seeing
kdump kernel hang at interrupt vector 0xc*4400. The reason is, with this
feature enabled, exception are raised with MMU (IR=DR=1) ON with the
default offset of 0xc*4000. Since exception is raised in virtual mode it
requires the vector region to be executable without which it fails to
fetch and execute instruction at 0xc*4xxx. For default kernel since kernel
is loaded at real 0, the htab mappings sets the entire kernel text region
executable. But for relocatable kernel (e.g. kdump case) we only copy
interrupt vectors down to real 0 and never marked that region as
executable because in p7 and below we always get exception in real mode.
This patch fixes this issue by marking htab mapping range as executable
that overlaps with the interrupt vector region for relocatable kernel.
Thanks to Ben who helped me to debug this issue and find the root cause.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Disable relocation on exception while going down even in kdump case. This
is because we are about clear htab mappings while kexec-ing into kdump
kernel and we may run into issues if we still have AIL ON.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit f5c57710dd ("powerpc/eeh: Use
partial hotplug for EEH unaware drivers") introduces eeh_rmv_device,
which may grab a reference to a driver, but not release it.
That prevents a driver from being removed after it has gone through EEH
recovery.
This patch drops the reference if it was taken.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 446f6d06fa ("powerpc/mpic: Properly
set default triggers") breaks the mpc7447_hpc_defconfig as follows:
CC arch/powerpc/sysdev/mpic.o
arch/powerpc/sysdev/mpic.c: In function 'mpic_set_irq_type':
arch/powerpc/sysdev/mpic.c:886:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:890:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:894:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:898:9: error: case label does not reduce to an integer constant
Looking at the cpp output (gcc 4.7.3), I see:
case mpic->hw_set[MPIC_IDX_VECPRI_SENSE_EDGE] |
mpic->hw_set[MPIC_IDX_VECPRI_POLARITY_POSITIVE]:
The pointer into an array appears because CONFIG_MPIC_WEIRD=y is set
for this platform, thus enabling the following:
-------------------
#ifdef CONFIG_MPIC_WEIRD
static u32 mpic_infos[][MPIC_IDX_END] = {
[0] = { /* Original OpenPIC compatible MPIC */
[...]
#define MPIC_INFO(name) mpic->hw_set[MPIC_IDX_##name]
#else /* CONFIG_MPIC_WEIRD */
#define MPIC_INFO(name) MPIC_##name
#endif /* CONFIG_MPIC_WEIRD */
-------------------
Here we convert the case section to if/else if, and also add
the equivalent of a default case to warn about unknown types.
Boot tested on sbc8548, build tested on all defconfigs.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull x86 fixes from Peter Anvin:
"Quite a varied little collection of fixes. Most of them are
relatively small or isolated; the biggest one is Mel Gorman's fixes
for TLB range flushing.
A couple of AMD-related fixes (including not crashing when given an
invalid microcode image) and fix a crash when compiled with gcov"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Unify valid container checks
x86, hweight: Fix BUG when booting with CONFIG_GCOV_PROFILE_ALL=y
x86/efi: Allow mapping BGRT on x86-32
x86: Fix the initialization of physnode_map
x86, cpu hotplug: Fix stack frame warning in check_irq_vectors_for_cpu_disable()
x86/intel/mid: Fix X86_INTEL_MID dependencies
arch/x86/mm/srat: Skip NUMA_NO_NODE while parsing SLIT
mm, x86: Revisit tlb_flushall_shift tuning for page flushes except on IvyBridge
x86: mm: change tlb_flushall_shift for IvyBridge
x86/mm: Eliminate redundant page table walk during TLB range flushing
x86/mm: Clean up inconsistencies when flushing TLB ranges
mm, x86: Account for TLB flushes only when debugging
x86/AMD/NB: Fix amd_set_subcaches() parameter type
x86/quirks: Add workaround for AMD F16h Erratum792
x86, doc, kconfig: Fix dud URL for Microcode data
does not conflict with the dynamic linker's one (64K)
- VDSO gettimeofday fix
- Barrier fixes for atomic operations and cache flushing
- TLB invalidation when overriding early page mappings during boot
- Wired up new 32-bit arm (compat) syscalls
- LSM_MMAP_MIN_ADDR when COMPAT is enabled
- defconfig update
- Clean-up (comments, pgd_alloc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
iQIcBAABAgAGBQJS9RgeAAoJEGvWsS0AyF7xeOoP/RDrU9spbXz0Kmb/pv8zeta+
LPZXQbf+stTD0nSUp1CoqUVKPMN8maMa6MOOP3KBFD23nya3UOko65dr2hpXz8qh
ripzD7XG9tpr1Npox1PN9O7vVpqKNCNdhwflOwpAZkQSXW7q6rduwFwLrvaFcb4z
ST41oz/tUhm0xerJFGypoj/peHr1WnAKz8mqMtnPBnQY9u0mk/l5+kEcFGH0pQXl
qkuvxDPBPKG/vL8KEHBCpwQ+i+1GWa2Duk8qY7VkJYYYnKfkrqCRiRwFycBF5tE/
sde021ERxyH8V3CD+Y21btAKW3dOn5/3sJq0gU8w+5vo/Axfm0uLOvHy5Ij9YQ9W
D6yFbNuFoqeeSYQjro2x81lwarDSHldsmcsSEoP1mDMflFQS1rw9wdEu+r9+PYxr
Za275GwDkApCSd5p+xgMrezwG1Xf26Nr6AigNXz7I8AhupxUff9IGM72wy/u5w7Z
rqNNF1jjWjiJXvb9Xb00ZdBaQBb5wcYEyCMvStgqplm1FvuLzMBkwZtPblir0ldl
8+3LTKtCcThN2rqjkwTq+d4H1wSL/0WxK9VlRtK1SEVu8mZOwlCQc9sfavFkhT8q
q0TmAVGXFxHrzpgtlJ5DQumUb7QdJTqWmeG5ohQu5kIr7nYZ1OhEXavHdxErWxUk
WpbPGYFsQDcAoIvnhh3P
=jhHX
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Relax VDSO alignment requirements so that the kernel-picked one (4K)
does not conflict with the dynamic linker's one (64K)
- VDSO gettimeofday fix
- Barrier fixes for atomic operations and cache flushing
- TLB invalidation when overriding early page mappings during boot
- Wired up new 32-bit arm (compat) syscalls
- LSM_MMAP_MIN_ADDR when COMPAT is enabled
- defconfig update
- Clean-up (comments, pgd_alloc).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: Expand default enabled features
arm64: asm: remove redundant "cc" clobbers
arm64: atomics: fix use of acquire + release for full barrier semantics
arm64: barriers: allow dsb macro to take option parameter
security: select correct default LSM_MMAP_MIN_ADDR on arm on arm64
arm64: compat: Wire up new AArch32 syscalls
arm64: vdso: update wtm fields for CLOCK_MONOTONIC_COARSE
arm64: vdso: fix coarse clock handling
arm64: simplify pgd_alloc
arm64: fix typo: s/SERRROR/SERROR/
arm64: Invalidate the TLB when replacing pmd entries during boot
arm64: Align CMA sizes to PAGE_SIZE
arm64: add DSB after icache flush in __flush_icache_all()
arm64: vdso: prevent ld from aligning PT_LOAD segments to 64k
Pull MIPS updates from Ralf Baechle:
"hree minor patches. All have sat in -next for a few days"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Fix build when CONFIG_BUG is not set
MIPS: Wire up sched_setattr/sched_getattr syscalls
MIPS: Alchemy: Fix DB1100 GPIO registration
FPGA implementations of the Cortex-A57 and Cortex-A53 are now available
in the form of the SMM-A57 and SMM-A53 Soft Macrocell Models (SMMs) for
Versatile Express. As these attach to a Motherboard Express V2M-P1 it
would be useful to have support for some V2M-P1 peripherals enabled by
default.
Additionally a couple of of features have been introduced since the last
defconfig update (CMA, jump labels) that would be good to have enabled
by default to ensure they are build and boot tested.
This patch updates the arm64 defconfig to enable support for these
devices and features. The arm64 Kconfig is modified to select
HAVE_PATA_PLATFORM, which is required to enable support for the
CompactFlash controller on the V2M-P1.
A few options which don't need to appear in defconfig are trimmed:
* BLK_DEV - selected by default
* EXPERIMENTAL - otherwise gone from the kernel
* MII - selected by drivers which require it
* USB_SUPPORT - selected by default
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
cbnz/tbnz don't update the condition flags, so remove the "cc" clobbers
from inline asm blocks that only use these instructions to implement
conditional branches.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linux requires a number of atomic operations to provide full barrier
semantics, that is no memory accesses after the operation can be
observed before any accesses up to and including the operation in
program order.
On arm64, these operations have been incorrectly implemented as follows:
// A, B, C are independent memory locations
<Access [A]>
// atomic_op (B)
1: ldaxr x0, [B] // Exclusive load with acquire
<op(B)>
stlxr w1, x0, [B] // Exclusive store with release
cbnz w1, 1b
<Access [C]>
The assumption here being that two half barriers are equivalent to a
full barrier, so the only permitted ordering would be A -> B -> C
(where B is the atomic operation involving both a load and a store).
Unfortunately, this is not the case by the letter of the architecture
and, in fact, the accesses to A and C are permitted to pass their
nearest half barrier resulting in orderings such as Bl -> A -> C -> Bs
or Bl -> C -> A -> Bs (where Bl is the load-acquire on B and Bs is the
store-release on B). This is a clear violation of the full barrier
requirement.
The simple way to fix this is to implement the same algorithm as ARMv7
using explicit barriers:
<Access [A]>
// atomic_op (B)
dmb ish // Full barrier
1: ldxr x0, [B] // Exclusive load
<op(B)>
stxr w1, x0, [B] // Exclusive store
cbnz w1, 1b
dmb ish // Full barrier
<Access [C]>
but this has the undesirable effect of introducing *two* full barrier
instructions. A better approach is actually the following, non-intuitive
sequence:
<Access [A]>
// atomic_op (B)
1: ldxr x0, [B] // Exclusive load
<op(B)>
stlxr w1, x0, [B] // Exclusive store with release
cbnz w1, 1b
dmb ish // Full barrier
<Access [C]>
The simple observations here are:
- The dmb ensures that no subsequent accesses (e.g. the access to C)
can enter or pass the atomic sequence.
- The dmb also ensures that no prior accesses (e.g. the access to A)
can pass the atomic sequence.
- Therefore, no prior access can pass a subsequent access, or
vice-versa (i.e. A is strictly ordered before C).
- The stlxr ensures that no prior access can pass the store component
of the atomic operation.
The only tricky part remaining is the ordering between the ldxr and the
access to A, since the absence of the first dmb means that we're now
permitting re-ordering between the ldxr and any prior accesses.
From an (arbitrary) observer's point of view, there are two scenarios:
1. We have observed the ldxr. This means that if we perform a store to
[B], the ldxr will still return older data. If we can observe the
ldxr, then we can potentially observe the permitted re-ordering
with the access to A, which is clearly an issue when compared to
the dmb variant of the code. Thankfully, the exclusive monitor will
save us here since it will be cleared as a result of the store and
the ldxr will retry. Notice that any use of a later memory
observation to imply observation of the ldxr will also imply
observation of the access to A, since the stlxr/dmb ensure strict
ordering.
2. We have not observed the ldxr. This means we can perform a store
and influence the later ldxr. However, that doesn't actually tell
us anything about the access to [A], so we've not lost anything
here either when compared to the dmb variant.
This patch implements this solution for our barriered atomic operations,
ensuring that we satisfy the full barrier requirements where they are
needed.
Cc: <stable@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The following path will cause array out of bound.
memblock_add_region() will always set nid in memblock.reserved to
MAX_NUMNODES. In numa_register_memblks(), after we set all nid to
correct valus in memblock.reserved, we called setup_node_data(), and
used memblock_alloc_nid() to allocate memory, with nid set to
MAX_NUMNODES.
The nodemask_t type can be seen as a bit array. And the index is 0 ~
MAX_NUMNODES-1.
After that, when we call node_set() in numa_clear_kernel_node_hotplug(),
the nodemask_t got an index of value MAX_NUMNODES, which is out of [0 ~
MAX_NUMNODES-1].
See below:
numa_init()
|---> numa_register_memblks()
| |---> memblock_set_node(memory) set correct nid in memblock.memory
| |---> memblock_set_node(reserved) set correct nid in memblock.reserved
| |......
| |---> setup_node_data()
| |---> memblock_alloc_nid() here, nid is set to MAX_NUMNODES (1024)
|......
|---> numa_clear_kernel_node_hotplug()
|---> node_set() here, we have an index 1024, and overflowed
This patch moves nid setting to numa_clear_kernel_node_hotplug() to fix
this problem.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Tested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reported-by: Dave Jones <davej@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Tested-by: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On-stack variable numa_kernel_nodes in numa_clear_kernel_node_hotplug()
was not initialized. So we need to initialize it.
[akpm@linux-foundation.org: use NODE_MASK_NONE, per David]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Tested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: David Rientjes <rientjes@google.com>
Tested-by: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For additional coverage, BorisO and friends unknowlingly did swap AMD
microcode with Intel microcode blobs in order to see what happens. What
did happen on 32-bit was
[ 5.722656] BUG: unable to handle kernel paging request at be3a6008
[ 5.722693] IP: [<c106d6b4>] load_microcode_amd+0x24/0x3f0
[ 5.722716] *pdpt = 0000000000000000 *pde = 0000000000000000
because there was a valid initrd there but without valid microcode in it
and the container check happened *after* the relocated ramdisk handling
on 32-bit, which was clearly wrong.
While at it, take care of the ramdisk relocation on both 32- and 64-bit
as it is done on both. Also, comment what we're doing because this code
is a bit tricky.
Reported-and-tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391460104-7261-1-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
__enable_fpu produces a build failure when CONFIG_BUG is not set:
In file included from arch/mips/kernel/cpu-probe.c:24:0:
arch/mips/include/asm/fpu.h: In function '__enable_fpu':
arch/mips/include/asm/fpu.h:77:1: error: control reaches end of non-void function [-Werror=return-type]
This is regression introduced in 3.14-rc1. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Paul Burton <paul.burton@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6504/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The dsb instruction takes an option specifying both the target access
types and shareability domain.
This patch allows such an option to be passed to the dsb macro,
resulting in potentially more efficient code. Currently the option is
ignored until all callers are updated (unlike ARM, the option is
mandated by the assembler).
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Revert "xen/grant-table: Avoid m2p_override during mapping" as it broke Xen ARM build.
- Fix CR4 not being set on AP processors in Xen PVH mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS8AyQAAoJEFjIrFwIi8fJbD4IAJssMuaLI5CRsSWBgDFHHDFt
srVJpDOYQiDr/TxkwFCVcL4sFy9Htb3KMArU4eIBl6uMqQbGa+3rHyXcHYI219YY
XH3D8RG+9JChwsxtaeUEzwx1C8ehcygD34vtdcoQXa7eBuEi4TL3HeLifR+HrXKO
UdFrTA34FmvpVFbSuRXkZh5sd6ca9et9xHuQHM8SIY6pVokY6xaEYOp17tfPZpwM
7A6LFjUjXeugHC2L3+/H8UOHA9nSZQvnMiZOWq2Cusc2Dt2V7emzgk2wcc2CHttf
EA6GbtiJzHqMPmt5EjubI9hHdSMB31HpY4hnQE38+ucl+BwiSdRE9z2Rm4TYClg=
=IX4M
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes:
- Revert "xen/grant-table: Avoid m2p_override during mapping" as it
broke Xen ARM build.
- Fix CR4 not being set on AP processors in Xen PVH mode"
* tag 'stable/for-linus-3.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: set CR4 flags for APs
Revert "xen/grant-table: Avoid m2p_override during mapping"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=G2gr
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64-syscalls' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 update from Tony Luck:
"Wire up new sched_setattr and sched_getattr syscalls"
* tag 'please-pull-ia64-syscalls' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Wire up new sched_setattr and sched_getattr syscalls
Pull crypto fixes from Herbert Xu:
"This fixes a number of concurrency issues on s390 where multiple users
of the same crypto transform may clobber each other's results"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390 - fix des and des3_ede ctr concurrency issue
crypto: s390 - fix des and des3_ede cbc concurrency issue
crypto: s390 - fix concurrency issue in aes-ctr mode
CONFIG_X86_32 doesn't map the boot services regions into the EFI memory
map (see commit 700870119f ("x86, efi: Don't map Boot Services on
i386")), and so efi_lookup_mapped_addr() will fail to return a valid
address. Executing the ioremap() path in efi_bgrt_init() causes the
following warning on x86-32 because we're trying to ioremap() RAM,
WARNING: CPU: 0 PID: 0 at arch/x86/mm/ioremap.c:102 __ioremap_caller+0x2ad/0x2c0()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.13.0-0.rc5.git0.1.2.fc21.i686 #1
Hardware name: DellInc. Venue 8 Pro 5830/09RP78, BIOS A02 10/17/2013
00000000 00000000 c0c0df08 c09a5196 00000000 c0c0df38 c0448c1e c0b41310
00000000 00000000 c0b37bc1 00000066 c043bbfd c043bbfd 00e7dfe0 00073eff
00073eff c0c0df48 c0448ce2 00000009 00000000 c0c0df9c c043bbfd 00078d88
Call Trace:
[<c09a5196>] dump_stack+0x41/0x52
[<c0448c1e>] warn_slowpath_common+0x7e/0xa0
[<c043bbfd>] ? __ioremap_caller+0x2ad/0x2c0
[<c043bbfd>] ? __ioremap_caller+0x2ad/0x2c0
[<c0448ce2>] warn_slowpath_null+0x22/0x30
[<c043bbfd>] __ioremap_caller+0x2ad/0x2c0
[<c0718f92>] ? acpi_tb_verify_table+0x1c/0x43
[<c0719c78>] ? acpi_get_table_with_size+0x63/0xb5
[<c087cd5e>] ? efi_lookup_mapped_addr+0xe/0xf0
[<c043bc2b>] ioremap_nocache+0x1b/0x20
[<c0cb01c8>] ? efi_bgrt_init+0x83/0x10c
[<c0cb01c8>] efi_bgrt_init+0x83/0x10c
[<c0cafd82>] efi_late_init+0x8/0xa
[<c0c9bab2>] start_kernel+0x3ae/0x3c3
[<c0c9b53b>] ? repair_env_string+0x51/0x51
[<c0c9b378>] i386_start_kernel+0x12e/0x131
Switch to using early_memremap(), which won't trigger this warning, and
has the added benefit of more accurately conveying what we're trying to
do - map a chunk of memory.
This patch addresses the following bug report,
https://bugzilla.kernel.org/show_bug.cgi?id=67911
Reported-by: Adam Williamson <awilliam@redhat.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
It can take some time to validate the image, make sure
{allyes|allmod}config doesn't enable it.
I'd say randconfig will cover it often enough, and the failure is also
borderline build coverage related: you cannot really make the decoder
test fail via source level changes, only with changes in the build
environment, so I agree with Andi that we can disable this one too.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Paul Gortmaker paul.gortmaker@windriver.com>
Suggested-and-acked-by: Andi Kleen andi@firstfloor.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes 'do_execve()' to get the executable name as a 'struct
filename', and to free it when it is done. This is what the normal
users want, and it simplifies and streamlines their error handling.
The controlled lifetime of the executable name also fixes a
use-after-free problem with the trace_sched_process_exec tracepoint: the
lifetime of the passed-in string for kernel users was not at all
obvious, and the user-mode helper code used UMH_WAIT_EXEC to serialize
the pathname allocation lifetime with the execve() having finished,
which in turn meant that the trace point that happened after
mm_release() of the old process VM ended up using already free'd memory.
To solve the kernel string lifetime issue, this simply introduces
"getname_kernel()" that works like the normal user-space getname()
function, except with the source coming from kernel memory.
As Oleg points out, this also means that we could drop the tcomm[] array
from 'struct linux_binprm', since the pathname lifetime now covers
setup_new_exec(). That would be a separate cleanup.
Reported-by: Igor Zhbanov <i.zhbanov@samsung.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update wall-to-monotonic fields in the VDSO data page
unconditionally. These are used to service CLOCK_MONOTONIC_COARSE,
which is not guarded by use_syscall.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When __kernel_clock_gettime is called with a CLOCK_MONOTONIC_COARSE or
CLOCK_REALTIME_COARSE clock id, it returns incorrectly to whatever the
caller has placed in x2 ("ret x2" to return from the fast path). Fix
this by saving x30/LR to x2 only in code that will call
__do_get_tspec, restoring x30 afterward, and using a plain "ret" to
return from the routine.
Also: while the resulting tv_nsec value for CLOCK_REALTIME and
CLOCK_MONOTONIC must be computed using intermediate values that are
left-shifted by cs_shift (x12, set by __do_get_tspec), the results for
coarse clocks should be calculated using unshifted values
(xtime_coarse_nsec is in units of actual nanoseconds). The current
code shifts intermediate values by x12 unconditionally, but x12 is
uninitialized when servicing a coarse clock. Fix this by setting x12
to 0 once we know we are dealing with a coarse clock id.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
