The current code abuses ifdefs to determine if the selected ECC scheme
is supported by the running kernel. As a result the code is hard to read,
and it also fails to load as a module.
This commit removes all the ifdefs and instead introduces a function
omap2_nand_ecc_check() to check if the ECC is supported by using
IS_ENABLED(CONFIG_xxx).
Since IS_ENABLED() is true when a config is =y or =m, this change fixes the
module so it can be loaded with no issues.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the full description of the Hynix H27UCG8T2ATR-BC NAND chip in the
nand_ids table so that we can later use the NAND ECC infos and ONFI timings
mode in controller drivers.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add an onfi_timing_mode_default field to nand_chip and nand_flash_dev in
order to support NAND timings definition for non-ONFI NAND.
NAND that support better timings mode than the default one have to define
a new entry in the nand_ids table.
The default timing mode should be deduced from timings description from
the datasheet and the ONFI specification
(www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
"Timing Parameters").
You should choose the closest mode that fit the timings requirements of
your NAND chip.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Previously, the only way to map a NOR device as a simple ROM was to
use the obsolete "direct-mapped" compatible binding (which further
requires device_type = "nor" and probe-type = "NOR" properties).
This patch adds an "mtd-rom" compatible binding to the "map_rom"
probe type.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "ROM" and unknown probe types within the obsolete "direct-mapped"
probe function used the nonexistent "mtd_rom" probe instead of the
intended "map_rom".
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We've been semi-officially queueing patches here for a while, and it's
in linux-next, so let's advertise it in MAINTAINERS.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
- Fix indents
- Do not break a line unless it is longer than 80 columns
- Do not insert a whitespace before ';'
- Use whitespaces around operators
- Use braces for a "else" block where the "if" block uses ones.
Besides, eliminate all the warnings reported by checkpatch.pl:
- WARNING: quoted string split across lines
- WARNING: else is not generally useful after a break or return
- WARNING: Missing a blank line after declarations
- WARNING: Avoid line continuations in quoted strings
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should use parentheses only when they are necessary
or they really improve the readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The variable "irq_status" in denali_read_page_raw() is set, but not used.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It looks like this header file is a concatenation of two headers.
Anyway, the include guard should be renamed and placed at the correct
postion and the license block in the middle should be deleted.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This follows Chapter 2 of Linux's CodingStyle:
> However, never break user-visible strings such as printk messages,
> because that breaks the ability to grep for them.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This won't be used by NAND subsystem as we implement cmdfunc on our
own, but will allow us to write a bit cleaner code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We are supposed to mask value, not multiply it. Add some comments btw.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Old devices used to have NVRAM at the very end of flash and they could
be unaligned (starting at some offset in a block).
In new devices NVRAM can be located quite randomly, however it seems to
always start at the beginning of a block. For example Netgear R6250 has
NVRAM located right after the bootloader, before the kernel partition.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For PMECC, the pmecc_bytes_per_sector has same meaning as ecc.bytes.
So remove pmecc_bytes_per_sector and use ecc.bytes instead.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For PMECC, the pmecc_sector_number has same meaning as ecc.steps.
So use ecc.steps to replace the pmecc_sector_number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.
If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.
As explained by Brian Norris the reasons for using a BBT are:
""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.
This has been acknowledged by several developers over the last several
years.
Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Retrieve the NFC clock to make sure it is enabled. Make that optional to ensure
compatibility with previous device trees but document it as mandatory so newer
device trees will include it.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The variable "retry" in wait_for_irq() is set, but not used.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should rathar use "int" type for loop iterators.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Useless casts result in unreadable source code.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
All of these variables are initialized to zero and then
set to a different value below.
Zero-initializing is redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should use
/*
* Blah Blah ...
* ...
*/
for multi-line comment blocks.
In addition, refactor some comments where it seems reasonable and
remove some comments where the code is clear enough such as:
/* clear interrupts */
clear_interrupts(denali);
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull vfs fixes from Al Viro:
"double iput() on failure exit in lustre, racy removal of spliced
dentries from ->s_anon in __d_materialise_dentry() plus a bunch of
assorted RCU pathwalk fixes"
The RCU pathwalk fixes end up fixing a couple of cases where we
incorrectly dropped out of RCU walking, due to incorrect initialization
and testing of the sequence locks in some corner cases. Since dropping
out of RCU walk mode forces the slow locked accesses, those corner cases
slowed down quite dramatically.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
be careful with nd->inode in path_init() and follow_dotdot_rcu()
don't bugger nd->seq on set_root_rcu() from follow_dotdot_rcu()
fix bogus read_seqretry() checks introduced in b37199e
move the call of __d_drop(anon) into __d_materialise_unique(dentry, anon)
[fix] lustre: d_make_root() does iput() on dentry allocation failure
The performance regression that Josef Bacik reported in the pathname
lookup (see commit 99d263d4c5 "vfs: fix bad hashing of dentries") made
me look at performance stability of the dcache code, just to verify that
the problem was actually fixed. That turned up a few other problems in
this area.
There are a few cases where we exit RCU lookup mode and go to the slow
serializing case when we shouldn't, Al has fixed those and they'll come
in with the next VFS pull.
But my performance verification also shows that link_path_walk() turns
out to have a very unfortunate 32-bit store of the length and hash of
the name we look up, followed by a 64-bit read of the combined hash_len
field. That screws up the processor store to load forwarding, causing
an unnecessary hickup in this critical routine.
It's caused by the ugly calling convention for the "hash_name()"
function, and easily fixed by just making hash_name() fill in the whole
'struct qstr' rather than passing it a pointer to just the hash value.
With that, the profile for this function looks much smoother.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc updates from Helge Deller:
"The most important patch is a new Light Weigth Syscall (LWS) for 8,
16, 32 and 64 bit atomic CAS operations which is required in order to
be able to implement the atomic gcc builtins on our platform.
Other than that, we wire up the seccomp, getrandom and memfd_create
syscalls, fixes a minor off-by-one bug and a wrong printk string"
* 'parisc-3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Implement new LWS CAS supporting 64 bit operations.
parisc: Wire up seccomp, getrandom and memfd_create syscalls
parisc: dino: fix %d confusingly prefixed with 0x in format string
parisc: sys_hpux: NUL terminator is one past the end
in the former we simply check if dentry is still valid after picking
its ->d_inode; in the latter we fetch ->d_inode in the same places
where we fetch dentry and its ->d_seq, under the same checks.
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
return the value instead, and have path_init() do the assignment. Broken by
"vfs: Fix absolute RCU path walk failures due to uninitialized seq number",
which was Cc-stable with 2.6.38+ as destination. This one should go where
it went.
To avoid dummy value returned in case when root is already set (it would do
no harm, actually, since the only caller that doesn't ignore the return value
is guaranteed to have nd->root *not* set, but it's more obvious that way),
lift the check into callers. And do the same to set_root(), to keep them
in sync.
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
MAINTAINERS to reflect new e-mail address.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uhqP
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.17' of git://github.com/jonmason/ntb
Pull ntb driver bugfixes from Jon Mason:
"NTB driver fixes for queue spread and buffer alignment. Also, update
to MAINTAINERS to reflect new e-mail address"
* tag 'ntb-3.17' of git://github.com/jonmason/ntb:
ntb: Add alignment check to meet hardware requirement
MAINTAINERS: update NTB info
NTB: correct the spread of queues over mw's
Pull ARM irq chip fixes from Thomas Gleixner:
"Another pile of ARM specific irq chip fixlets:
- off by one bugs in the crossbar driver
- missing annotations
- a bunch of "make it compile" updates
I pulled the lot today from Jason, but it has been in -next for at
least a week"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: gic-v3: Declare rdist as __percpu pointer to __iomem pointer
irqchip: gic: Make gic_default_routable_irq_domain_ops static
irqchip: exynos-combiner: Fix compilation error on ARM64
irqchip: crossbar: Off by one bugs in init
irqchip: gic-v3: Tag all low level accessors __maybe_unused
irqchip: gic-v3: Only define gic_peek_irq() when building SMP
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Update my contact info to my personal email address and add Dave Jiang.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Pull futex and timer fixes from Thomas Gleixner:
"A oneliner bugfix for the jinxed futex code:
- Drop hash bucket lock in the error exit path. I really could slap
myself for intruducing that bug while fixing all the other horror
in that code three month ago ...
and the timer department is not too proud about the following fixes:
- Deal with a long standing rounding bug in the timeval to jiffies
conversion. It's a real issue and this fix fell through the cracks
for quite some time.
- Another round of alarmtimer fixes. Finally this code gets used
more widely and the subtle issues hidden for quite some time are
noticed and fixed. Nothing really exciting, just the itty bitty
details which bite the serious users here and there"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Unlock hb->lock in futex_wait_requeue_pi() error path
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Lock k_itimer during timer callback
alarmtimer: Do not signal SIGEV_NONE timers
alarmtimer: Return relative times in timer_gettime
jiffies: Fix timeval conversion to jiffies
The current LWS cas only works correctly for 32bit. The new LWS allows
for CAS operations of variable size.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>
Josef Bacik found a performance regression between 3.2 and 3.10 and
narrowed it down to commit bfcfaa77bd ("vfs: use 'unsigned long'
accesses for dcache name comparison and hashing"). He reports:
"The test case is essentially
for (i = 0; i < 1000000; i++)
mkdir("a$i");
On xfs on a fio card this goes at about 20k dir/sec with 3.2, and 12k
dir/sec with 3.10. This is because we spend waaaaay more time in
__d_lookup on 3.10 than in 3.2.
The new hashing function for strings is suboptimal for <
sizeof(unsigned long) string names (and hell even > sizeof(unsigned
long) string names that I've tested). I broke out the old hashing
function and the new one into a userspace helper to get real numbers
and this is what I'm getting:
Old hash table had 1000000 entries, 0 dupes, 0 max dupes
New hash table had 12628 entries, 987372 dupes, 900 max dupes
We had 11400 buckets with a p50 of 30 dupes, p90 of 240 dupes, p99 of 567 dupes for the new hash
My test does the hash, and then does the d_hash into a integer pointer
array the same size as the dentry hash table on my system, and then
just increments the value at the address we got to see how many
entries we overlap with.
As you can see the old hash function ended up with all 1 million
entries in their own bucket, whereas the new one they are only
distributed among ~12.5k buckets, which is why we're using so much
more CPU in __d_lookup".
The reason for this hash regression is two-fold:
- On 64-bit architectures the down-mixing of the original 64-bit
word-at-a-time hash into the final 32-bit hash value is very
simplistic and suboptimal, and just adds the two 32-bit parts
together.
In particular, because there is no bit shuffling and the mixing
boundary is also a byte boundary, similar character patterns in the
low and high word easily end up just canceling each other out.
- the old byte-at-a-time hash mixed each byte into the final hash as it
hashed the path component name, resulting in the low bits of the hash
generally being a good source of hash data. That is not true for the
word-at-a-time case, and the hash data is distributed among all the
bits.
The fix is the same in both cases: do a better job of mixing the bits up
and using as much of the hash data as possible. We already have the
"hash_32|64()" functions to do that.
Reported-by: Josef Bacik <jbacik@fb.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hash_64() function historically does the multiply by the
GOLDEN_RATIO_PRIME_64 number with explicit shifts and adds, because
unlike the 32-bit case, gcc seems unable to turn the constant multiply
into the more appropriate shift and adds when required.
However, that means that we generate those shifts and adds even when the
architecture has a fast multiplier, and could just do it better in
hardware.
Use the now-cleaned-up CONFIG_ARCH_HAS_FAST_MULTIPLIER (together with
"is it a 64-bit architecture") to decide whether to use an integer
multiply or the explicit sequence of shift/add instructions.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It used to be an ad-hoc hack defined by the x86 version of
<asm/bitops.h> that enabled a couple of library routines to know whether
an integer multiply is faster than repeated shifts and additions.
This just makes it use the real Kconfig system instead, and makes x86
(which was the only architecture that did this) select the option.
NOTE! Even for x86, this really is kind of wrong. If we cared, we would
probably not enable this for builds optimized for netburst (P4), where
shifts-and-adds are generally faster than multiplies. This patch does
*not* change that kind of logic, though, it is purely a syntactic change
with no code changes.
This was triggered by the fact that we have other places that really
want to know "do I want to expand multiples by constants by hand or
not", particularly the hash generation code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
as clean. This could cause no writeback to occur or spurious dirty
block counts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUEG6eAAoJEMUj8QotnQNabuUIALF4UnJov622hmGIcBC91j8m
HRD1gNqu8hOLrtQEP+E7fdrDwHqyxAdL2kFN6nowbvuWmSVAUpQmsLCbXOvQOttx
mELPFSOw2s1FpBbt63pIi8icAPCvzJYeR+jGN3m//b0eVFkmQ6xQGazhbd3JF+xP
mHeEVNTF7acbUYDdfejF8kNJcUbpU63IF5UzRGOXMTNZ2DnFvEiBJHtgXJKiIkhN
MhZNFgqeRdIppoDImnGJ9kQrWzoXGIpAXbxFbvjLofpr6HK2FxWLayeib0Jdm+Ze
znHjSqyRRBhtszk/c8Rxqzy9dotMi3fI/O4pVkziSMYKCjtt9dCRFbP1Gkwaf3w=
=6q2l
-----END PGP SIGNATURE-----
Merge tag 'dm-3.17-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a race in the DM cache target that caused dirty blocks to be
marked as clean. This could cause no writeback to occur or spurious
dirty block counts"
* tag 'dm-3.17-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix race causing dirty blocks to be marked as clean
Pull block fixes from Jens Axboe:
"A small collection of fixes for the current rc series. This contains:
- Two small blk-mq patches from Rob Elliott, cleaning up error case
at init time.
- A fix from Ming Lei, fixing SG merging for blk-mq where
QUEUE_FLAG_SG_NO_MERGE is the default.
- A dev_t minor lifetime fix from Keith, fixing an issue where a
minor might be reused before all references to it were gone.
- Fix from Alan Stern where an unbalanced queue bypass caused SCSI
some headaches when it does a series of add/del on devices without
fully registrering the queue.
- A fix from me for improving the scaling of tag depth in blk-mq if
we are short on memory"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: scale depth and rq map appropriate if low on memory
Block: fix unbalanced bypass-disable in blk_register_queue
block: Fix dev_t minor allocation lifetime
blk-mq: cleanup after blk_mq_init_rq_map failures
blk-mq: pass along blk_mq_alloc_tag_set return values
blk-merge: fix blk_recount_segments
arm64.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gWAc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen ARM bugfix from Stefano Stabellini:
"The patches fix the "xen_add_mach_to_phys_entry: cannot add" bug that
has been affecting xen on arm and arm64 guests since 3.16. They
require a few hypervisor side changes that just went in xen-unstable.
A couple of days ago David sent out a pull request with a few other
Xen fixes (it is already in master). Sorry we didn't synchronized
better among us"
* tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/arm: remove mach_to_phys rbtree
xen/arm: reimplement xen_dma_unmap_page & friends
xen/arm: introduce XENFEAT_grant_map_identity
