PCIE_MODULE_NAME is only used once and offers no benefit, so remove it.
Link: https://lore.kernel.org/lkml/20190509141456.223614-10-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Replace the last uses of dbg() with the equivalent pr_debug(), then remove
unused dbg(), err(), info(), and warn() wrappers.
Link: https://lore.kernel.org/lkml/20190509141456.223614-9-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Log messages with pci_dev, not pcie_device. Factor out common message
prefixes with dev_fmt().
Example output change:
- pciehp 0000:00:06.0:pcie004: Slot(0) Powering on due to button press
+ pcieport 0000:00:06.0: pciehp: Slot(0) Powering on due to button press
Link: https://lore.kernel.org/lkml/20190509141456.223614-8-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Previously pciehp debug messages were enabled by the pciehp_debug module
parameter, e.g., by booting with this kernel command line option:
pciehp.pciehp_debug=1
Convert this mechanism to use the generic dynamic debug (dyndbg) feature.
After this commit, pciehp debug messages are enabled by building the kernel
with CONFIG_DYNAMIC_DEBUG=y and booting with this command line option:
dyndbg="file pciehp* +p"
The dyndbg facility is much more flexible: messages can be enabled at boot-
or run-time based on the file name, function name, line number, message
test, etc. See Documentation/admin-guide/dynamic-debug-howto.rst for more
details.
Link: https://lore.kernel.org/lkml/20190509141456.223614-7-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: commit log, comment, remove pciehp_debug parameter]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Basically we need to do the same thing when runtime suspending than with
system sleep so re-use those operations here. This makes sure hotplug
interrupt does not trigger immediately when the link goes down.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When PCIe hotplug port is transitioned into D3hot, the link to the
downstream component will go down. If hotplug interrupt generation is
enabled when that happens, it will trigger immediately, waking up the
system and bringing the link back up.
To prevent this, disable hotplug interrupt generation when system suspend
is entered. This does not prevent wakeup from low power states according
to PCIe 4.0 spec section 6.7.3.4:
Software enables a hot-plug event to generate a wakeup event by
enabling software notification of the event as described in Section
6.7.3.1. Note that in order for software to disable interrupt generation
while keeping wakeup generation enabled, the Hot-Plug Interrupt Enable
bit must be cleared.
So as long as we have set the slot event mask accordingly, wakeup should
work even if slot interrupt is disabled. The port should trigger wake and
then send PME to the root port when the PCIe hierarchy is brought back up.
Limit this to systems using native PME mechanism to make sure older Apple
systems depending on commit e3354628c376 ("PCI: pciehp: Support interrupts
sent from D3hot") still continue working.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PCI port driver saves the PCI state after initializing the device with
the applicable service devices. This was, however, before the service
drivers were even registered because PCI probe happens before the
device_initcall initialized those service drivers. The config space state
that the services set up were not being saved. The end result would cause
PCI devices to not react to events that the drivers think they did if the
PCI state ever needed to be restored.
Fix this by changing the service drivers from using the init calls to
having the portdrv driver calling the services directly. This will get the
state saved as desired, while making the relationship between the port
driver and the services under it more explicit in the code.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
When the PCI hotplug core and its first user, cpqphp, were introduced in
February 2002 with historic commit a8a2069f432c, cpqphp allocated a slot
struct for its internal use plus a hotplug_slot struct to be registered
with the hotplug core and linked the two with pointers:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Nowadays, the predominant pattern in the tree is to embed ("subclass")
such structures in one another and cast to the containing struct with
container_of(). But it wasn't until July 2002 that container_of() was
introduced with historic commit ec4f214232cf:
https://git.kernel.org/tglx/history/c/ec4f214232cf
pnv_php, introduced in 2016, did the right thing and embedded struct
hotplug_slot in its internal struct pnv_php_slot, but all other drivers
cargo-culted cpqphp's design and linked separate structs with pointers.
Embedding structs is preferrable to linking them with pointers because
it requires fewer allocations, thereby reducing overhead and simplifying
error paths. Casting an embedded struct to the containing struct
becomes a cheap subtraction rather than a dereference. And having fewer
pointers reduces the risk of them pointing nowhere either accidentally
or due to an attack.
Convert all drivers to embed struct hotplug_slot in their internal slot
struct. The "private" pointer in struct hotplug_slot thereby becomes
unused, so drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # drivers/pci/hotplug/s390*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Ever since the PCI hotplug core was introduced in 2002, drivers had to
allocate and register a struct hotplug_slot_info for every slot:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Apparently the idea was that drivers furnish the hotplug core with an
up-to-date card presence status, power status, latch status and
attention indicator status as well as notify the hotplug core of changes
thereof. However only 4 out of 12 hotplug drivers bother to notify the
hotplug core with pci_hp_change_slot_info() and the hotplug core never
made any use of the information: There is just a single macro in
pci_hotplug_core.c, GET_STATUS(), which uses the hotplug_slot_info if
the driver lacks the corresponding callback in hotplug_slot_ops. The
macro is called when the user reads the attribute via sysfs.
Now, if the callback isn't defined, the attribute isn't exposed in sysfs
in the first place (see e.g. has_power_file()). There are only two
situations when the hotplug_slot_info would actually be accessed:
* If the driver defines ->enable_slot or ->disable_slot but not
->get_power_status.
* If the driver defines ->set_attention_status but not
->get_attention_status.
There is no driver doing the former and just a single driver doing the
latter, namely pnv_php.c. Amend it with a ->get_attention_status
callback. With that, the hotplug_slot_info becomes completely unused by
the PCI hotplug core. But a few drivers use it internally as a cache:
cpcihp uses it to cache the latch_status and adapter_status.
cpqhp uses it to cache the adapter_status.
pnv_php and rpaphp use it to cache the attention_status.
shpchp uses it to cache all four values.
Amend these drivers to cache the information in their private slot
struct. shpchp's slot struct already contains members to cache the
power_status and adapter_status, so additional members are only needed
for the other two values. In the case of cpqphp, the cached value is
only accessed in a single place, so instead of caching it, read the
current value from the hardware.
Caution: acpiphp, cpci, cpqhp, shpchp, asus-wmi and eeepc-laptop
populate the hotplug_slot_info with initial values on probe. That code
is herewith removed. There is a theoretical chance that the code has
side effects without which the driver fails to function, e.g. if the
ACPI method to read the adapter status needs to be executed at least
once on probe. That seems unlikely to me, still maintainers should
review the changes carefully for this possibility.
Rafael adds: "I'm not aware of any case in which it will break anything,
[...] but if that happens, it may be necessary to add the execution of
the control methods in question directly to the initialization part."
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # drivers/pci/hotplug/s390*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Of the members which were just moved from pciehp's slot struct to the
controller struct, rename "lock" to "state_lock" and rename "work" to
"button_work" for clarity. Perform the rename separately to the
unification of the two structs per Sinan's request.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sinan Kaya <okaya@kernel.org>
pciehp was originally introduced together with shpchp in a single
commit, c16b4b14d980 ("PCI Hotplug: Add SHPC and PCI Express hot-plug
drivers"):
https://git.kernel.org/tglx/history/c/c16b4b14d980
shpchp supports up to 31 slots per controller, hence uses separate slot
and controller structs. pciehp has a 1:1 relationship between slot and
controller and therefore never required this separation. Nevertheless,
because much of the code had been copy-pasted between the two drivers,
pciehp likewise uses separate structs to this very day.
The artificial separation of data structures adds unnecessary complexity
and bloat to pciehp and requires constantly chasing pointers at runtime.
Simplify the driver by merging struct slot into struct controller.
Merge the slot constructor pcie_init_slot() and the destructor
pcie_cleanup_slot() into the controller counterparts.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The WiGig Bus Extension (WBE) specification allows tunneling PCIe over
IEEE 802.11. A product implementing this spec is the wil6210 from
Wilocity (now part of Qualcomm Atheros). It integrates a PCIe switch
with a wireless network adapter:
00.0-+ [1ae9:0101] Upstream Port
+-00.0-+ [1ae9:0200] Downstream Port
| +-00.0 [168c:0034] Atheros AR9462 Wireless Network Adapter
+-02.0 [1ae9:0201] Downstream Port
+-03.0 [1ae9:0201] Downstream Port
Wirelessly attached devices presumably appear below the hotplug ports
with device ID [1ae9:0201]. Oddly, the Downstream Port [1ae9:0200]
leading to the wireless network adapter is likewise Hotplug Capable,
but has its Presence Detect State bit hardwired to zero. Even if the
Link Active bit is set, Presence Detect is zero, so this cannot be
caused by in-band presence detection but only by broken hardware.
pciehp assumes an empty slot if Presence Detect State is zero,
regardless of Link Active being one. Consequently, up until v4.18 it
removes the wireless network adapter in pciehp_resume(). From v4.19 it
already does so in pciehp_probe().
Be lenient towards broken hardware and assume the slot is occupied if
Link Active is set: Introduce pciehp_card_present_or_link_active()
and use it in lieu of pciehp_get_adapter_status() everywhere, except
in pciehp_handle_presence_or_link_change() whose log messages depend
on which of Presence Detect State or Link Active is set.
Remove the Presence Detect State check from __pciehp_enable_slot()
because it is only called if either of Presence Detect State or Link
Active is set.
Caution: There is a possibility that broken hardware exists which has
working Presence Detect but hardwires Link Active to one. On such
hardware the slot will now incorrectly be considered always occupied.
If such hardware is discovered, this commit can be rolled back and a
quirk can be added which sets is_hotplug_bridge = 0 for [1ae9:0200].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200839
Reported-and-tested-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
pciehp's ->enable_slot, ->disable_slot, ->get_attention_status and
->reset_slot callbacks are currently implemented by wrapper functions
that do nothing else but call down to a backend function. The backends
are not called from anywhere else, so drop the wrappers and use the
backends directly as callbacks, thereby shaving off a few lines of
unnecessary code.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Drop the following includes from pciehp source files which no longer use
any of the included symbols:
* <linux/sched/signal.h> in pciehp.h
<linux/signal.h> in pciehp_hpc.c
Added by commit de25968cc8 ("fix more missing includes") to
accommodate for a call to signal_pending().
The call was removed by commit 262303fe32 ("pciehp: fix wait command
completion").
* <linux/interrupt.h> in pciehp_core.c
Added by historic commit f308a2dfbe63 ("PCI: add PCI Express Port Bus
Driver subsystem") to accommodate for a call to free_irq():
https://git.kernel.org/tglx/history/c/f308a2dfbe63
The call was removed by commit 407f452b05 ("pciehp: remove
unnecessary free_irq").
* <linux/time.h> in pciehp_core.c and pciehp_hpc.c
Added by commit 34d03419f0 ("PCIEHP: Add Electro Mechanical
Interlock (EMI) support to the PCIE hotplug driver."),
which was reverted by commit bd3d99c170 ("PCI: Remove untested
Electromechanical Interlock (EMI) support in pciehp.").
* <linux/module.h> in pciehp_ctrl.c, pciehp_hpc.c and pciehp_pci.c
Added by historic commit c16b4b14d980 ("PCI Hotplug: Add SHPC and PCI
Express hot-plug drivers"):
https://git.kernel.org/tglx/history/c/c16b4b14d980
Module-related symbols were neither used back then in those files,
nor are they used today.
* <linux/slab.h> in pciehp_ctrl.c
Added by commit 5a0e3ad6af ("include cleanup: Update gfp.h and
slab.h includes to prepare for breaking implicit slab.h inclusion from
percpu.h") to accommodate for calls to kmalloc().
The calls were removed by commit 0e94916e60 ("PCI: pciehp: Handle
events synchronously").
* "../pci.h" in pciehp_ctrl.c
Added by historic commit 67f4660b72f2 ("PCI: ASPM patch for") to
accommodate for usage of the global variable pcie_mch_quirk:
https://git.kernel.org/tglx/history/c/67f4660b72f2
The global variable was removed by commit 0ba379ec0f ("PCI: Simplify
hotplug mch quirk").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On driver probe and on resume from system sleep, pciehp checks the
Presence Detect State bit in the Slot Status register to bring up an
occupied slot or bring down an unoccupied slot. Both code paths are
identical, so deduplicate them per Mika's request.
On probe, an additional check is performed to disable power of an
unoccupied slot. This can e.g. happen if power was enabled by BIOS.
It cannot happen once pciehp has taken control, hence is not necessary
on resume: The Slot Control register is set to the same value that it
had on suspend by pci_restore_state(), so if the slot was occupied,
power is enabled and if it wasn't, power is disabled. Should occupancy
have changed during the system sleep transition, power is adjusted by
bringing up or down the slot per the paragraph above.
To allow for deduplication of the presence check, move the power check
to pcie_init(). This seems safer anyway, because right now it is
performed while interrupts are already enabled, and although I can't
think of a scenario where pciehp_power_off_slot() and the IRQ thread
collide, it does feel brittle.
However this means that pcie_init() may now write to the Slot Control
register before the IRQ is requested. If both the CCIE and HPIE bits
happen to be set, pcie_wait_cmd() will wait for an interrupt (instead
of polling the Command Completed bit) and eventually emit a timeout
message. Additionally, if a level-triggered INTx interrupt is used,
the user may see a spurious interrupt splat. Avoid by disabling
interrupts before disabling power. (Normally the HPIE and CCIE bits
should be clear on probe, but conceivably they may already have been
set e.g. by BIOS.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Ensure accessibility of a hotplug port's config space when accessed via
sysfs by resuming its parent to D0.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Upon resume from system sleep, the Slot Control register is written via:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
PCIe r4.0, sec 6.7.3.2 says that after "issuing a write transaction that
targets any portion of the Port's Slot Control register, [...] software
must wait for [the] command to complete before issuing the next command".
pciehp currently fails to enforce that rule after the above-mentioned
write. Fix it.
(Moving restoration of the Slot Control register to pciehp doesn't seem
to make sense because the other PCIe hotplug drivers may need it as
well.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840fe ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
The ->reset_slot callback introduced by commits:
2e35afaefe ("PCI: pciehp: Add reset_slot() method") and
06a8d89af5 ("PCI: pciehp: Disable link notification across slot reset")
disables notification of Presence Detect Changed and Data Link Layer
State Changed events for the duration of a secondary bus reset.
However a bus reset not only triggers these events, but may also clear
the Presence Detect State bit in the Slot Status register and the Data
Link Layer Link Active bit in the Link Status register momentarily.
According to Sinan Kaya:
"I know for a fact that bus reset clears the Data Link Layer Active bit
as soon as link goes down. It gets set again following link up.
Presence detect depends on the HW implementation. QDT root ports
don't change presence detect for instance since nobody actually
removed the card. If an implementation supports in-band presence
detect, the answer is yes. As soon as the link goes down, presence
detect bit will get cleared until recovery."
https://lkml.kernel.org/r/42e72f83-3b24-f7ef-e5bc-290fae99259a@codeaurora.org
In-band presence detect is also covered in Table 4-15 in PCIe r4.0,
sec 4.2.6.
pciehp should therefore ensure that any parts of the driver that access
those bits do not run concurrently to a bus reset. The only precaution
the commits took to that effect was to halt interrupt polling. They
made no effort to drain the slot workqueue, cancel an outstanding
Attention Button work, or block slot enable/disable requests via sysfs
and in the ->probe hook.
Now that pciehp is converted to enable/disable the slot exclusively from
the IRQ thread, the only places accessing the two above-mentioned bits
are the IRQ thread and the ->probe hook. Add locking to serialize them
with a bus reset. This obviates the need to halt interrupt polling.
Do not add locking to the ->get_adapter_status sysfs callback to afford
users unfettered access to that bit. Use an rw_semaphore in lieu of a
regular mutex to allow parallel execution of the non-reset code paths
accessing the critical bits, i.e. the IRQ thread and the ->probe hook.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Sinan Kaya <okaya@kernel.org>
Per PCIe r4.0, sec 6.7.3.4, a "port may optionally send an MSI when
there are hot-plug events that occur while interrupt generation is
disabled, and interrupt generation is subsequently enabled."
On probe, we currently clear all event bits in the Slot Status register
with the notable exception of the Presence Detect Changed bit. Thereby
we seek to receive an interrupt for an already occupied slot once event
notification is enabled.
But because the interrupt is optional, users may have to specify the
pciehp_force parameter on the command line, which is inconvenient.
Moreover, now that pciehp's event handling has become resilient to
missed events, a Presence Detect Changed interrupt for a slot which is
powered on is interpreted as removal of the card. If the slot has
already been brought up by the BIOS, receiving such an interrupt on
probe causes the slot to be powered off and immediately back on, which
is likewise undesirable.
Avoid both issues by making the behavior of pciehp_force the default and
clearing the Presence Detect Changed bit on probe.
Note that the stated purpose of pciehp_force per the MODULE_PARM_DESC
("Force pciehp, even if OSHP is missing") seems nonsensical because the
OSHP control method is only relevant for SHCP slots according to the
PCI Firmware specification r3.0, sec 4.8.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Besides the IRQ thread, there are several other places in the driver
which enable or disable the slot:
- pciehp_probe() enables the slot if it's occupied and the pciehp_force
module parameter is used.
- pciehp_resume() enables or disables the slot after system sleep.
- pciehp_queue_pushbutton_work() enables or disables the slot after the
5 second delay following an Attention Button press.
- pciehp_sysfs_enable_slot() and pciehp_sysfs_disable_slot() enable or
disable the slot on sysfs write.
This requires locking and complicates pciehp's state machine.
A simplification can be achieved by enabling and disabling the slot
exclusively from the IRQ thread.
Amend the functions listed above to request slot enable/disablement from
the IRQ thread by either synthesizing a Presence Detect Changed event or,
in the case of a disable user request (via sysfs or an Attention Button
press), submitting a newly introduced force disable request. The latter
is needed because the slot shall be forced off despite being occupied.
For this force disable request, avoid colliding with Slot Status register
bits by using a bit number greater than 16.
For synchronous execution of requests (on sysfs write), wait for the
request to finish and retrieve the result. There can only ever be one
sysfs write in flight due to the locking in kernfs_fop_write(), hence
there is no risk of returning the result of a different sysfs request to
user space.
The POWERON_STATE and POWEROFF_STATE is now no longer entered by the
above-listed functions, but solely by the IRQ thread when it begins a
power transition. Afterwards, it moves to STATIC_STATE. The same
applies to canceling the Attention Button work, it likewise becomes an
IRQ thread only operation.
An immediate consequence is that the POWERON_STATE and POWEROFF_STATE is
never observed by the IRQ thread itself, only by functions called in a
different context, such as pciehp_sysfs_enable_slot(). So remove
handling of these states from pciehp_handle_button_press() and
pciehp_handle_link_change() which are exclusively called from the IRQ
thread.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI hotplug core has just been refactored to separate slot
initialization for in-kernel use from publication to user space.
Take advantage of it in pciehp by publishing to user space last on
probe. This will allow enable/disablement of the slot exclusively from
the IRQ thread because the IRQ is requested after initialization for
in-kernel use (thereby getting its unique name needed by the IRQ thread)
but before user space is able to submit enable/disable requests.
On teardown, the order is the same in reverse: The user space interface
is removed prior to freeing the IRQ and destroying the slot.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a hotplug driver calls pci_hp_register(), all steps necessary for
registration are carried out in one go, including creation of a kobject
and addition to sysfs. That's a problem for pciehp once it's converted
to enable/disable the slot exclusively from the IRQ thread: The thread
needs to be spawned after creation of the kobject (because it uses the
kobject's name), but before addition to sysfs (because it will handle
enable/disable requests submitted via sysfs).
pci_hp_deregister() does offer a ->release callback that's invoked
after deletion from sysfs and before destruction of the kobject. But
because pci_hp_register() doesn't offer a counterpart, hotplug drivers'
->probe and ->remove code becomes asymmetric, which is error prone
as recently discovered use-after-free bugs in pciehp's ->remove hook
have shown.
In a sense, this appears to be a case of the midlayer antipattern:
"The core thesis of the "midlayer mistake" is that midlayers are
bad and should not exist. That common functionality which it is
so tempting to put in a midlayer should instead be provided as
library routines which can [be] used, augmented, or ignored by
each bottom level driver independently. Thus every subsystem
that supports multiple implementations (or drivers) should
provide a very thin top layer which calls directly into the
bottom layer drivers, and a rich library of support code that
eases the implementation of those drivers. This library is
available to, but not forced upon, those drivers."
-- Neil Brown (2009), https://lwn.net/Articles/336262/
The presence of midlayer traits in the PCI hotplug core might be ascribed
to its age: When it was introduced in February 2002, the blessings of a
library approach might not have been well known:
https://git.kernel.org/tglx/history/c/a8a2069f432c
For comparison, the driver core does offer split functions for creating
a kobject (device_initialize()) and addition to sysfs (device_add()) as
an alternative to carrying out everything at once (device_register()).
This was introduced in October 2002:
https://git.kernel.org/tglx/history/c/8b290eb19962
The odd ->release callback in the PCI hotplug core was added in 2003:
https://git.kernel.org/tglx/history/c/69f8d663b595
Clearly, a library approach would not force every hotplug driver to
implement a ->release callback, but rather allow the driver to remove
the sysfs files, release its data structures and finally destroy the
kobject. Alternatively, a driver may choose to remove everything with
pci_hp_deregister(), then release its data structures.
To this end, offer drivers pci_hp_initialize() and pci_hp_add() as a
split-up version of pci_hp_register(). Likewise, offer pci_hp_del()
and pci_hp_destroy() as a split-up version of pci_hp_deregister().
Eliminate the ->release callback and move its code into each driver's
teardown routine.
Declare pci_hp_deregister() void, in keeping with the usual kernel
pattern that enablement can fail, but disablement cannot. It only
returned an error if the caller passed in a NULL pointer or a slot which
has never or is no longer registered or is sharing its name with another
slot. Those would be bugs, so WARN about them. Few hotplug drivers
actually checked the return value and those that did only printed a
useless error message to dmesg. Remove that.
For most drivers the conversion was straightforward since it doesn't
matter whether the code in the ->release callback is executed before or
after destruction of the kobject. But in the case of ibmphp, it was
unclear to me whether setting slot_cur->ctrl and slot_cur->bus_on to
NULL needs to happen before the kobject is destroyed, so I erred on
the side of caution and ensured that the order stays the same. Another
nontrivial case is pnv_php, I've found the list and kref logic difficult
to understand, however my impression was that it is safe to delete the
list element and drop the references until after the kobject is
destroyed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Previously the slot workqueue was used to handle events and enable or
disable the slot. That's no longer the case as those tasks are done
synchronously in the IRQ thread. The slot workqueue is thus merely used
to handle a button press after the 5 second delay and only one such work
item may be in flight at any given time. A separate workqueue isn't
necessary for this simple task, so use the system workqueue instead.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the attention button is pressed to power on the slot AND the user
powers on the slot via sysfs before 5 seconds have elapsed AND powering
on the slot fails because either the slot is unoccupied OR the latch is
open, we neglect turning off the green LED so it keeps on blinking.
That's because the error path of pciehp_sysfs_enable_slot() doesn't call
pciehp_green_led_off(), unlike pciehp_power_thread() which does.
The bug has been present since 2004 when the driver was introduced.
Fix by deduplicating common code in pciehp_sysfs_enable_slot() and
pciehp_power_thread() into a wrapper function pciehp_enable_slot() and
renaming the existing function to __pciehp_enable_slot(). Same for
pciehp_disable_slot(). This will also simplify the upcoming rework of
pciehp's event handling.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When pciehp is unbound (e.g. on unplug of a Thunderbolt device), the
hotplug_slot struct is deregistered and thus freed before freeing the
IRQ. The IRQ handler and the work items it schedules print the slot
name referenced from the freed structure in various informational and
debug log messages, each time resulting in a quadruple dereference of
freed pointers (hotplug_slot -> pci_slot -> kobject -> name).
At best the slot name is logged as "(null)", at worst kernel memory is
exposed in logs or the driver crashes:
pciehp 0000:10:00.0:pcie204: Slot((null)): Card not present
An attacker may provoke the bug by unplugging multiple devices on a
Thunderbolt daisy chain at once. Unplugging can also be simulated by
powering down slots via sysfs. The bug is particularly easy to trigger
in poll mode.
It has been present since the driver's introduction in 2004:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Fix by rearranging teardown such that the IRQ is freed first. Run the
work items queued by the IRQ handler to completion before freeing the
hotplug_slot struct by draining the work queue from the ->release_slot
callback which is invoked by pci_hp_deregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.4
After a suspend/resume cycle the Presence Detect or Data Link Layer Status
Changed bits might be set. If we don't clear them those events will not
fire anymore and nothing happens for instance when a device is now
hot-unplugged.
Fix this by clearing those bits in a newly introduced function
pcie_reenable_notification(). This should be fine because immediately
after, we check if the adapter is still present by reading directly from
the status register.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Add SPDX GPL-2.0+ to all PCI files that specified the GPL and allowed
either GPL version 2 or any later version.
Remove the boilerplate GPL version 2 or later language, relying on the
assertion in b24413180f ("License cleanup: add SPDX GPL-2.0 license
identifier to files with no license") that the SPDX identifier may be used
instead of the full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the "PCI Express Hot Plug Controller Driver" version message. I
don't think it contains any useful information. Remove unused #defines
and move the author information to a comment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/hotplug:
x86/PCI: VMD: Request userspace control of PCIe hotplug indicators
PCI: pciehp: Allow exclusive userspace control of indicators
PCI: pciehp: Remove useless pciehp_get_latch_status() calls
PCI: pciehp: Clean up dmesg "Slot(%s)" messages
PCI: pciehp: Remove unnecessary guard
PCI: pciehp: Don't re-read Slot Status when handling surprise event
PCI: pciehp: Don't re-read Slot Status when queuing hotplug event
PCI: pciehp: Process all hotplug events before looking for new ones
PCI: pciehp: Return IRQ_NONE when we can't read interrupt status
PCI: pciehp: Rename pcie_isr() locals for clarity
PCI: pciehp: Clear attention LED on device add
PCIe hotplug supports optional Attention and Power Indicators, which are
used internally by pciehp. Users can't control the Power Indicator, but
they can control the Attention Indicator by writing to a sysfs "attention"
file.
The Slot Control register has two bits for each indicator, and the PCIe
spec defines the encodings for each as (Reserved/On/Blinking/Off). For
sysfs "attention" writes, pciehp_set_attention_status() maps into these
encodings, so the only useful write values are 0 (Off), 1 (On), and 2
(Blinking).
However, some platforms use all four bits for platform-specific indicators,
and they need to allow direct user control of them while preventing pciehp
from using them at all.
Add a "hotplug_user_indicators" flag to the pci_dev structure. When set,
pciehp does not use either the Attention Indicator or the Power Indicator,
and the low four bits (values 0x0 - 0xf) of sysfs "attention" write values
are written directly to the Attention Indicator Control and Power Indicator
Control fields.
[bhelgaas: changelog, rename flag and accessors to s/attention/indicator/]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
obj-$(CONFIG_HOTPLUG_PCI_PCIE) += pciehp.o
pciehp-objs := pciehp_core.o \
drivers/pci/pcie/Kconfig:config HOTPLUG_PCI_PCIE
drivers/pci/pcie/Kconfig: bool "PCI Express Hotplug driver"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, module_init() translates to
device_initcall(). One could argue that we should use subsys_initcall()
here, but for now we stick with runtime equivalence.
We delete module.h but we keep the moduleparam.h include, since we are
keeping the module_param() that the file has as-is for now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kristen Carlson Accardi <kristen@linux.intel.com>
Fix all whitespace issues (missing or needed whitespace) in all files in
drivers/pci. Code is compiled with allyesconfig before and after code
changes and objects are recorded and checked with objdiff and they are not
changed after this commit.
Signed-off-by: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pciehp debug logging is overly verbose and often redundant. Almost all
of the information printed by dbg_ctrl() is also printed by the normal PCI
core enumeration code and by pcie_init().
Remove the redundant debug info.
When claiming a pciehp bridge, we print the slot characteristics, e.g.,
Slot #6 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+
Add the Hot-Plug Capable and Hot-Plug Surprise bits to this information,
and print it all in the same order as lspci does.
No functional change except the message text changes.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The err_out_none label in pciehp_probe() only leads to a return statement,
so use return statements instead of jumps to it and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Jarod Wilson reports that ExpressCard hotplug doesn't work on HP ZBook G2.
The problem turns out to be the ACPI-based "slot detection" code called
from pciehp_probe() which uses questionable heuristics based on what ACPI
objects are present for the PCIe port device to figure out whether to
register a hotplug slot for that port.
That code is used if there is at least one PCIe port having an ACPI device
configuration object related to hotplug (such as _EJ0 or _RMV), and the
Thunderbolt port on the ZBook has _RMV. Of course, Thunderbolt and PCIe
native hotplug need not be mutually exclusive (as they aren't on the
ZBook), so that rule is simply incorrect.
Moreover, the ACPI-based "slot detection" check does not add any value if
pciehp_probe() is called at all and the service type of the device object
it has been called for is PCIE_PORT_SERVICE_HP, because PCIe hotplug
services are only registered if the _OSC handshake in acpi_pci_root_add()
allows the kernel to control the PCIe native hotplug feature. No more
checks need to be carried out to decide whether or not to register a native
PCIe hotlug slot in that case.
For the above reasons, make pciehp_probe() check if it has been called for
the right service type and drop the pointless ACPI-based "slot detection"
check from it. Also remove the entire code whose only user is that check
(the entire pciehp_acpi.c file goes away as a result) and drop function
headers related to it from the internal pciehp header file.
Link: http://lkml.kernel.org/r/1431632038-39917-1-git-send-email-jarod@redhat.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=98581
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
This reverts bceee4a97e ("PCI: pciehp: Prevent NULL dereference during
probe") because it was accidentally applied twice:
62e4492c30 ("PCI: Prevent NULL dereference during pciehp probe")
bceee4a97e ("PCI: pciehp: Prevent NULL dereference during probe")
Revert the latter to dispose of the duplicated code block.
[bhelgaas: tidy changelog, drop stable tag]
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Andreas Noever <andreas.noever@gmail.com>
pciehp assumes that dev->subordinate, the struct pci_bus for a bridge's
secondary bus, exists. But we do not create that bus if we run out of bus
numbers during enumeration. This leads to a NULL dereference in
init_slot() (and other places).
Change pciehp_probe() to return -ENODEV when no secondary bus is present.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.2+
pciehp assumes that dev->subordinate exists. But we do not assign a bus if
we run out of bus numbers during enumeration. This leads to a NULL
dereference in init_slot() (and other places).
Change pciehp_probe() to return -ENODEV when no subordinate bus is present.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Merge quoted strings that are broken across lines into a single entity.
The compiler merges them anyway, but checkpatch complains about it, and
merging them makes it easier to grep for strings.
No functional change.
[bhelgaas: changelog, do the same for everything under drivers/pci]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix various whitespace errors.
No functional change.
[bhelgaas: fix other similar problems]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Today it is there is no protection around pciehp_enable_slot() and
pciehp_disable_slot() to ensure that they complete before another
hot-plug operation can be done on that particular slot.
This patch introduces the slot->hotplug_lock to ensure that any hotplug
operations (add / remove) complete before another hotplug event can begin
processing on that particular slot.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Using 'make namespacecheck' identify code which should be declared static.
Checked for users in other driver/archs as well. Compile tested only.
This stops exporting the following interfaces to modules:
pci_target_state()
pci_load_saved_state()
[bhelgaas: retained pci_find_next_ext_capability() and pci_cfg_space_size()]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These functions:
pcie_enable_notification()
pciehp_power_off_slot()
pciehp_get_power_status()
pciehp_get_attention_status()
pciehp_set_attention_status()
pciehp_get_latch_status()
pciehp_get_adapter_status()
pcie_write_cmd()
now always return success, so this patch makes them void and drops the
error-checking code in their callers.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCIe hotplug has a bus per slot, so we can just use a normal
secondary bus reset. However, if a slot supports surprise removal,
a bus reset can be seen as a presence detection change triggering
a hot-remove followed by a hot-add. Disable presence detection from
triggering an interrupt or being polled around the bus reset.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ER3b
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
In each suspend and resume cycle my laptop prints these messages at
KERN_INFO level:
pciehp 0000:00:1c.1:pcie04: pciehp_suspend ENTRY
pciehp 0000:00:1c.0:pcie04: pciehp_suspend ENTRY
and
pciehp 0000:00:1c.0:pcie04: pciehp_resume ENTRY
pciehp 0000:00:1c.1:pcie04: pciehp_resume ENTRY
Drop these messages, that were probably used to debug the suspend and
resume code, but now serve no purpose.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
