Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is part of an effort to clean-up the MFD subsystem.
ERROR: space required after that ',' (ctx:VxO)
+ 0, &twl6040_irq_chip,&twl6040->irq_data);
^
ERROR: space required before that '&' (ctx:OxV)
+ 0, &twl6040_irq_chip,&twl6040->irq_data);
^
total: 2 errors, 0 warnings, 816 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the MCLK is 19.2 or 38.4 MHz the HPPLL need to be enabled and can be
put in bypass mode.
This will fix HPPLL use on boards with 19.2MHz mclk.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make sure that we patch the ACCCTL register as the first thing when the
driver loads, thus configuring I2C fast mode and i2c access for dual access
registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In certain boards the source for the clk32k clock can be gated. In these
boards the clk32k clock can be provided to the driver and it is going to be
enabled/disabled when it is needed.
If the clk32k clock is not provided the driver will assume that it is always
running.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All boards using twl6040 configures the i2c bus to 400KHz. While twl6040's
defaults to normal mode (100KHz). So far twl6040 has no problem with i2c
communication in this configuration it is safer to select fast i2c mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If for some reason the boot loader enabled the audpwron GPIO we will have
pending IRQs to be handled. This seams to break twl6040 for some reason
leading to non working i2c communication (i2c timeouts). Clearing the INTID
register after we requested the audpwron GPIO (and set it to low) will
ensure that the chip will operate normally in this case as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We may have an error when reading the revision register, so check for
the returned value.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When probing, regmap_register_patch() will bypass the cache and perform
i2c writes for the given patches. It is thus unnecessary to manually set
the TWL6040_REG_ACCCTL register just before, as it will be done when
registering the twl6040_patch.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following sparse warning:
drivers/mfd/twl6040.c:89:20: warning:
symbol 'twl6040_patch' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add reg_defaults to regmap and at the same time implement proper power
state handling with using regcache_cache_only(), regcache_sync() and
regcache_mark_dirty().
This will make sure that we do not need to do restore operations in child
drivers anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The devm_request_irq function allocates irq that is released
when a driver detaches. Thus, there is no reason to explicitly
call devm_free_irq in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rather then open coding a cache of the vibra control registers use the
regmap cache code. Also cache the interrupt mask register, providing
a small performance improvement for the interrupt code.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The err: label is not needed we can just return instead of the jump there.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
To comply with coding style.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6040 is used only with OMAP4/5 SoCs and they can only boot in in DT mode.
The support for pdata/legacy boot can be removed.
Add TODO comment to the header file that all pdata struct can be removed in
the next merge window (after the sub driver updates are in).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the regmap_irq conversion there is no need to call the driver
as twl6040-core.c since there is only one c file remained.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
