Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe7 ("gpio: pca953x: Synchronize interrupt handler properly")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- automatically drive GPHY leds in gpio-stp-xway
- refactor ->{get, set}_multiple() in gpio-aggregator
- add support for a new model in rcar-gpio DT bindings
- simplify several GPIO drivers with dev_err_probe()
- disable Direct KBD interrupts in gpio-tc35894
- use DEFINE_SEQ_ATTRIBUTE() in GPIO chardev to shrink code
- switch to using a simpler IDA API in gpiolib
- make devprop_gpiochip_set_names() more generic by using device properties
instead of using fwnode helpers
-----BEGIN PGP SIGNATURE-----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=RbA2
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.10-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.10 - part 1
- automatically drive GPHY leds in gpio-stp-xway
- refactor ->{get, set}_multiple() in gpio-aggregator
- add support for a new model in rcar-gpio DT bindings
- simplify several GPIO drivers with dev_err_probe()
- disable Direct KBD interrupts in gpio-tc35894
- use DEFINE_SEQ_ATTRIBUTE() in GPIO chardev to shrink code
- switch to using a simpler IDA API in gpiolib
- make devprop_gpiochip_set_names() more generic by using device properties
instead of using fwnode helpers
Add support for the GPIO controller of the sl28 board management
controller. This driver is part of a multi-function device.
A controller has 8 lines. There are three different flavors:
full-featured GPIO with interrupt support, input-only and output-only.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's possible for a GPIO chip to not have a parent device (whose
properties we inspect for 'gpio-line-names'). In this case we should
simply return from devprop_gpiochip_set_names(). Add an appropriate
check for this use-case.
Fixes: 7cba1a4d5e ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The introduced line event handling ABI in the commit
61f922db72 ("gpio: userspace ABI for reading GPIO line events")
missed the fact that 64-bit kernel may serve for 32-bit applications.
In such case the very first check in the lineevent_read() will fail
due to alignment differences.
To workaround this introduce lineevent_get_size() helper which returns actual
size of the structure in user space.
Fixes: 61f922db72 ("gpio: userspace ABI for reading GPIO line events")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Now that devprop_gpiochip_set_names() is only used in a single place
inside drivers/gpio/gpiolib.c, there's no need anymore for it to be
exported or to even live in its own source file. Pull this function into
the core source file for gpiolib.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
devprop_gpiochip_set_names() is overly complicated with taking the
fwnode argument (which requires using dev_fwnode() & of_fwnode_handle()
in ACPI and OF GPIO code respectively). Let's just switch to using the
generic device properties.
This allows us to pull the code setting line names directly into
gpiochip_add_data_with_key() instead of handling it separately for
ACPI and OF.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We don't need to specify any ranges when allocating IDs so we can switch
to ida_alloc() and ida_free() instead of the ida_simple_ counterparts.
ida_simple_get(ida, 0, 0, gfp) is equivalent to
ida_alloc_range(ida, 0, UINT_MAX, gfp) which is equivalent to
ida_alloc(ida, gfp). Note: IDR will never actually allocate an ID
larger than INT_MAX.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The gpio-siox driver uses handle_nested_irq() to implement its
interrupt support. This is only capable of handling threaded irq
actions. For a hardirq action it triggers a NULL pointer oops.
(It calls action->thread_fn which is NULL then.)
Prevent registration of a hardirq action by setting
gpio_irq_chip::threaded to true.
Cc: u.kleine-koenig@pengutronix.de
Fixes: be8c8facc7 ("gpio: new driver to work with a 8x12 siox")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
On tc35894, have to disable direct keypad interrupts to make
it as general purpose interrupts functionality work.
if not, after chip reset, IRQST(0x91) will always 0x20,
IRQN always low level, can't be clear.
Configure DIRECTx to enable general purpose gpio mode,
else read GPIOMISx register always zero in irq routine.
verified on tc35894, need more test on other tc3589x.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
Fixes: d88b25be35 ("gpio: Add TC35892 GPIO driver")
Cc: Cc: stable@vger.kernel.org
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb ("gpio: Add GPIO driver for Spreadtrum SC9860 platform")
Signed-off-by: Taiping Lai <taiping.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since the resource managed version of gpiochip_add_data() will handle the
GPIO-chip data automated cleanup we can freely remove the DW APB GPIO
driver code responsible for that. After doing so the DW APB GPIO driver
removal callback can be also fully discarded since there is nothing left
to be done for it. All the cleanups are now performed by means of the
device managed framework.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The kernel clock framework provides the resource managed version of
the clk_bulk_get() method. The only thing which needs to be also automated
is the clocks disable/unprepare procedure executed on the device removal.
It can be implemented by means of the custom action definition. After that
the clocks acquisition and release will be purely managed by the device
resources interface.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reset control interface provides the resource managed version of
the reset_control_get() method. The only thing which needs to be also
automated is the reset lane assertion on the device removal. It can be
implemented by means of the custom action definition. After that the reset
control will be purely managed by the device resources interface.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIOlib-based IRQ-chip interface is now utilized there is no need
in calling the methods acpi_gpiochip_{request,free}_interrupts() here.
They will be called from gpiochip_add_irqchip()/gpiochip_irqchip_remove()
anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIOlib-based IRQ-chip interface is now utilized there is no need in
setting up a custom GPIO-to-IRQ mapping method. GPIO-lib defines the
standard mapping method - gpiochip_to_irq(), which will be used anyway no
matter whether the custom to_irq callback is specified or not.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO-lib provides a ready-to-use interface to initialize an IRQ-chip on
top of a GPIO chip. It's better from maintainability and readability
point of view to use one instead of supporting a hand-written Generic
IRQ-chip-based implementation. Moreover the new implementation won't
cause much functional overhead but will provide a cleaner driver code.
All of that makes the DW APB GPIO driver conversion pretty much justified
especially seeing a tendency of the other GPIO drivers getting converted
too.
Here is what we do in the framework of this commit to convert the driver
to using the GPIO-lib-based IRQ-chip interface:
1) IRQ ack, mask and unmask callbacks are locally defined instead of
using the Generic IRQ-chip ones.
2) An irq_chip structure instance is embedded into the dwapb_gpio
private data. Note we can't have a static instance of that structure since
GPIO-lib will add some hooks into it by calling gpiochip_set_irq_hooks().
A warning about that would have been printed by the GPIO-lib code if we
used a single irq_chip structure instance for multiple DW APB GPIO
controllers.
3) Initialize the gpio_irq_chip structure embedded into the gpio_chip
descriptor. By default there is no IRQ enabled so any event raised will be
handled by the handle_bad_irq() IRQ flow handler. If DW APB GPIO IP-core
is synthesized to have non-shared reference IRQ-lines, then as before the
hierarchical and cascaded cases are distinguished by checking how many
parental IRQs are defined. (Note irq_set_chained_handler_and_data() won't
initialize IRQs, which descriptors couldn't be found.) If DW APB GPIO IP
is used on a platform with shared IRQ line, then we simply won't let the
GPIO-lib to initialize the parental IRQs, but will handle them locally in
the driver.
4) Discard linear IRQ-domain and Generic IRQ-chip initialization, since
GPIO-lib IRQ-chip interface will create a new domain and accept a standard
IRQ-chip structure pointer based on the setting we provided in the
gpio_irq_chip structure.
5) Manually select a proper IRQ flow handler directly in the
irq_set_type() callback by calling irq_set_handler_locked() method, since
an ordinary (not Generic) irq_chip descriptor is now utilized. Note this
shalln't give any regression
6) Alter CONFIG_GPIO_DWAPB kernel config to select
CONFIG_GPIOLIB_IRQCHIP instead of CONFIG_GENERIC_IRQ_CHIP.
Note neither 4) nor 5) shall cause a regression of commit 6a2f4b7dad
("gpio: dwapb: use a second irq chip"), since the later isn't properly
used here anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a new macro DWAPB_MAX_GPIOS which defines the maximum possible number
of GPIO lines corresponding to the maximum DW APB GPIO controller port
width. Use the new macro instead of number literal 32 where it's
applicable.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For better readability let's group all the IRQ handlers in a single place
of the driver instead of having them scatter around all over the file.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Indeed generic GPIO DT-schema implies that number of GPIOs should be
described by the "ngpios" property located under a GPIO-provider DT node.
In that case it's redundant to have a vendor-specific "snps,nr-gpios"
property describing the same setting. Moreover it might be errors prone.
Since commit 93d2e4322a ("of: platform: Batch fwnode parsing when adding
all top level devices") the fwnode parsing is resumed after the vast
majority of the platform devices are added. Implicitly that commit
activates re-parsing of the whole device tree GPIOs-phandle properties
detected having "-gpio/-gpios" suffixes. Since the vendor-specific number
of GPIOs property is defined with "-gpios" suffix, then of_link_property()
will consider it as a suffix-property with "#gpio-cells" structure, which
obviously it doesn't have. As a result for two DW APB GPIO controllers
we'll have the next errors printed.
OF: /bus@1f059000/gpio@1f044000/gpio-port@0: could not find phandle
OF: /bus@1f059000/gpio@1f045000/gpio-port@0: could not get #gpio-cells for /opp-table
OF: /bus@1f059000/gpio@1f044000/gpio-port@0: could not find phandle
OF: /bus@1f059000/gpio@1f045000/gpio-port@0: could not get #gpio-cells for /opp-table
See, the kernel fwnode parsing procedure even tried to resolve the phandle
ID, which it thought was the opp-table DT-node, while in fact it was just
a number "32". What would happen if that magic number actually referred to
a GPIO DT-node with "#gpio-cells" property defined?..
In order to fix the problem let's mark the "snps,nr-gpios" property as
deprecated and add the generic "ngpios" property support with the same
purpose as the deprecated one. That and the errors log above shall
motivate the platform developer to convert the DW APB GPIO DT-nodes to
using the standard number of GPIOs property.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix warnings for omap_gpio_resume and omap_gpio_suspend
defined but not used when PM is disabled as noticed when
doing make randconfig builds.
Fixes: f02a03985d ("gpio: omap: Add missing PM ops for suspend")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Sparse can't see locking scheme used in ->get_multiple() and
->set_multiple() callbacks.
CHECK .../drivers/gpio/gpio-aggregator.c
.../spinlock.h:409:9: warning: context imbalance in 'gpio_fwd_get_multiple' - unexpected unlock
.../spinlock.h:409:9: warning: context imbalance in 'gpio_fwd_set_multiple' - unexpected unlock
Refactor them to have better readability and make Sparse happy.
Code size impact is +52 bytes with arm-linux-gnueabihf-gcc 7.5.0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Ar10 (xr300) has 3 and grx390 (xrx330) has 4 built-in GPHY. PHY LEDs are
connected via STP. STP is a peripheral controller used to drive external
shift register cascades. The hardware is able to allow the GPHY to drive
some GPIO of the cascade automatically.This patch allows for this on ar10
and grx390.
Tested on D-Link DWR-966 with OpenWRT.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Core changes:
- Introduce the for_each_requested_gpio() macro to help in
dependent code all over the place. Also patch a few locations
to use it while we are at it.
- Split out the sysfs code into its own file.
- Split out the character device code into its own file, then
make a set of refactorings and improvements to this code.
We are setting the stage to revamp the userspace API a bit
in the next cycle.
- Fix a whole slew of kerneldoc that was wrong or missing.
New drivers:
- The PCA953x driver now supports the PCAL9535.
Driver improvements:
- A host of incremental modernizations and improvements to the
PCA953x driver.
- Incremental improvements to the Xilinx Zynq driver.
- Some improvements to the GPIO aggregator driver.
- I ran all over the place switching all threaded and other
drivers requesting their own IRQ while using the core
GPIO IRQ helpers to pass the GPIO irq chip as a template
instead of calling the explicit set-up functions. Next merge
window we may retire the old code altogether.
-----BEGIN PGP SIGNATURE-----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=OSvz
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.9 kernel cycle.
There is nothing too exciting in it, but a new macro that fixes a
build failure on a minor ARM32 platform that appeared yesterday is
part of it so we better merge it.
Core changes:
- Introduce the for_each_requested_gpio() macro to help in dependent
code all over the place. Also patch a few locations to use it while
we are at it.
- Split out the sysfs code into its own file.
- Split out the character device code into its own file, then make a
set of refactorings and improvements to this code. We are setting
the stage to revamp the userspace API a bit in the next cycle.
- Fix a whole slew of kerneldoc that was wrong or missing.
New drivers:
- The PCA953x driver now supports the PCAL9535.
Driver improvements:
- A host of incremental modernizations and improvements to the
PCA953x driver.
- Incremental improvements to the Xilinx Zynq driver.
- Some improvements to the GPIO aggregator driver.
- I ran all over the place switching all threaded and other drivers
requesting their own IRQ while using the core GPIO IRQ helpers to
pass the GPIO irq chip as a template instead of calling the
explicit set-up functions. Next merge window we may retire the old
code altogether"
* tag 'gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (97 commits)
gpio: wcove: Request IRQ after all initialisation done
gpio: crystalcove: Free IRQ on error path
gpio: pca953x: Request IRQ after all initialisation done
gpio: don't use same lockdep class for all devm_gpiochip_add_data users
gpio: max732x: Use irqchip template
gpio: stmpe: Move chip registration
gpio: rcar: Use irqchip template
gpio: regmap: fix type clash
gpio: Correct kernel-doc inconsistency
gpio: pci-idio-16: Use irqchip template
gpio: pcie-idio-24: Use irqchip template
gpio: 104-idio-16: Use irqchip template
gpio: 104-idi-48: Use irqchip template
gpio: 104-dio-48e: Use irqchip template
gpio: ws16c48: Use irqchip template
gpio: omap: improve coding style for pin config flags
gpio: dln2: Use irqchip template
gpio: sch: Add a blank line between declaration and code
gpio: sch: changed every 'unsigned' to 'unsigned int'
gpio: ich: changed every 'unsigned' to 'unsigned int'
...
There is logically better to request IRQ when we initialise all structures.
Align the driver with the rest on the same matter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200728125504.27786-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that all, but request_irq(), calls in the driver are device managed.
In unlikely case of devm_gpiochip_add_data() failure the IRQ left requested.
Free IRQ on error path by switching to devm_request_threaded_irq() API.
Byproduct of this change is a drop of ->remove() callback completely.
Fixes: 945e72db36 ("gpio: crystalcove: Use irqchip template")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200728125504.27786-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is logically better to request IRQ when we initialise all structures.
Align the driver with the rest on the same matter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200728125504.27786-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 959bc7b22b ("gpio: Automatically add lockdep keys") documents
in its commits message its intention to "create a unique class key for
each driver".
It does so by having gpiochip_add_data add in-place the definition of
two static lockdep classes for LOCKDEP use. That way, every caller of
the macro adds their gpiochip with unique lockdep classes.
There are many indirect callers of gpiochip_add_data, however, via
use of devm_gpiochip_add_data. devm_gpiochip_add_data has external
linkage and all its users will share the same lockdep classes, which
probably is not intended.
Fix this by replicating the gpio_chip_add_data statics-in-macro for
the devm_ version as well.
Fixes: 959bc7b22b ("gpio: Automatically add lockdep keys")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200731123835.8003-1-a.fatoum@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20200726221259.133536-1-linus.walleij@linaro.org
Make sure to register the GPIO chip after requesting the
interrupt and setting up the IRQ members of the irqchip.
Fixes: 9745079609 ("gpio: stmpe: Use irqchip template")
Reported-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200728072706.348725-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Biju Das <biju.das@bp.renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200722113141.243163-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722110649.202223-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722110027.192782-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722105517.186137-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722104820.174654-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722103915.162156-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722101938.151265-1-linus.walleij@linaro.org
Change the handling of pin config flags from if/else to switch
statement to make the code more readable and cleaner.
Suggested-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200722120755.230741-1-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add(). The irqchip is
instead added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Octavian Purdila <octavian.purdila@nxp.com>
Link: https://lore.kernel.org/r/20200722073426.38890-1-linus.walleij@linaro.org
* Move GPIO PMIC drivers to use IRQ chip template
* Introduce for_each_requested_gpio() and convert existing users
* Replace unsigned by unsigned int in few drivers
* Fix an issue in kernel doc that validator complains about
* Move to verbose debug level the IRQ status message in gpio-pch
The following is an automated git shortlog grouped by driver:
ARM/orion/gpio:
- Make use of for_each_requested_gpio()
crystalcove:
- Use irqchip template
- changed every 'unsigned' to 'unsigned int'
gpiolib:
- Introduce for_each_requested_gpio_in_range() macro
gpio-ml-ioh:
- Fix missing ':' in 'struct ioh_gpio_reg_data
ich:
- changed every 'unsigned' to 'unsigned int'
mvebu:
- Make use of for_each_requested_gpio()
pch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
- Move IRQ status message to verbose debug level
pinctrl:
- at91: Make use of for_each_requested_gpio()
sch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
wcove:
- Use irqchip template
xra1403:
- Make use of for_each_requested_gpio()
-----BEGIN PGP SIGNATURE-----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=txvs
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.9-1
* Move GPIO PMIC drivers to use IRQ chip template
* Introduce for_each_requested_gpio() and convert existing users
* Replace unsigned by unsigned int in few drivers
* Fix an issue in kernel doc that validator complains about
* Move to verbose debug level the IRQ status message in gpio-pch
The following is an automated git shortlog grouped by driver:
ARM/orion/gpio:
- Make use of for_each_requested_gpio()
crystalcove:
- Use irqchip template
- changed every 'unsigned' to 'unsigned int'
gpiolib:
- Introduce for_each_requested_gpio_in_range() macro
gpio-ml-ioh:
- Fix missing ':' in 'struct ioh_gpio_reg_data
ich:
- changed every 'unsigned' to 'unsigned int'
mvebu:
- Make use of for_each_requested_gpio()
pch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
- Move IRQ status message to verbose debug level
pinctrl:
- at91: Make use of for_each_requested_gpio()
sch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
wcove:
- Use irqchip template
xra1403:
- Make use of for_each_requested_gpio()
Added a lined between a declaration and other statements according to the
kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This converts the PPC4xx SPI driver to use GPIO descriptors.
The driver is already just picking some GPIOs from the device
tree so the conversion is pretty straight forward. However
this driver is looking form a pure "gpios" property rather
than the standard binding "cs-gpios" so we need to add a new
exception to the gpiolib OF parser to allow this for this
driver's compatibles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20200714072226.26071-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Added a lined between a declaration and other statements according to the
kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200717144040.63253-1-linus.walleij@linaro.org
Modify omap_gpio_set_config() to handle pin config bias flags by calling
gpiochip_generic_config().
The pin group for the gpio line must have the corresponding pinconf
properties:
PIN_CONFIG_BIAS_PULL_UP requires "pinctrl-single,bias-pullup"
PIN_CONFIG_BIAS_PULL_DOWN requires "pinctrl-single,bias-pulldown"
This is necessary for pcs_pinconf_set() to find the requested bias
parameter in the PIN_MAP_TYPE_CONFIGS_GROUP pinctrl map.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200715213738.1640030-1-drew@beagleboard.org
Link: https://lore.kernel.org/r/20200717194043.1774643-1-drew@beagleboard.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Anders Darander <anders@chargestorm.se>
Cc: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200717144835.68150-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Nikolaus Voss <nv@vosn.de>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20200716150502.195821-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Link: https://lore.kernel.org/r/20200716120318.127176-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200716100638.112451-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200716093459.76378-1-linus.walleij@linaro.org
Most other drivers fill out the gpio_irq_chip using a
struct gpio_irq_chip *girq helper variable for ease of
reading.
We also make a habit of explicitly assigning NULL and
zero to the parent IRQs when using ordinary IRQ handlers
in the driver, mostly for code readability and
maintenance.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200716092835.69176-1-linus.walleij@linaro.org
I noticed on Nexus 7 that after rebooting from downstream kernel to
upstream, the GPIO interrupt is triggering non-stop despite interrupts
being disabled for all of GPIOs. This happens because Nexus 7 uses a
soft-reboot, meaning that bootloader should take care of resetting
hardware, but the bootloader doesn't do it well. As a result, GPIO
interrupt may be left ON at a boot time. Let's mask all GPIO interrupts
at the driver's initialization time in order to resolve the issue.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-7-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change addresses one of the GPIO-core TODOs for the MAX77620 driver
which requires modern drivers to use the irqchip template. Instead of
using the GPIO's irqchip-helpers for creating the IRQ domain, the
gpio_irq_chip structure is now filled by the driver itself and then
gpiochip_add_data() takes care of instantiating the IRQ domain for us.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-6-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The platform_get_irq() returns a positive interrupt number on success and
negative error code on failure (zero shouldn't ever happen in practice, it
would produce a noisy warning). Hence let's return the error code directly
instead of overriding it with -ENODEV.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-5-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiochip_add_data() takes care of setting the of_node to the parent's
device of_node, hence there is no need to do it manually in the driver's
code. This patch corrects the parent's device pointer and removes the
unnecessary setting of the of_node.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-4-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The requested interrupt is never released by the driver. Fix this by
using the resource-managed variant of request_threaded_irq().
Fixes: ab3dd9cc24 ("gpio: max77620: Fix interrupt handling")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org> # 5.5+
Link: https://lore.kernel.org/r/20200709171203.12950-3-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MAX77620_GPIO_NR enum value represents the total number of GPIOs,
let's use it instead of a raw value in order to improve the code's
readability a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-2-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consolidate the cleanup of lineevents, currently duplicated in
lineevent_create and lineevent_release, into a helper function
lineevent_free.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Consolidate the cleanup of linehandles, currently duplicated in
linehandle_create and linehandle_release, into a helper function
linehandle_free.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Remove recalculation of offset from desc, where desc itself was calculated
from offset.
There is no benefit from the desc -> hwgpio conversion in this context.
The only implicit benefit of the offset -> desc -> hwgpio is
the range check in the offset -> desc, but where desc is required you
still get that, and where desc isn't required it is simpler to perform
the range check directly.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Merge separate usage of test_bit/set_bit into test_and_set_bit to remove
the possibility of a race between the test and set.
Similarly test_bit and clear_bit.
In the existing code it is possible for two threads to race past the
test_bit and then set or clear the watch bit, and neither return EBUSY.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename priv to cdev to improve readability.
The name "priv" indicates that the object is pointed to by
file->private_data, not what the object is actually is.
As it is always used to point to a struct gpio_chardev_data, renaming
it to cdev is more appropriate.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Replace usage of atomic_notifier_call_chain with
blocking_notifier_call_chain as the notifier function,
lineinfo_changed_notify, calls gpio_desc_to_lineinfo,
which calls pinctrl_gpio_can_use_line, which can sleep.
The chain isn't being called from an atomic context so the
the blocking notifier is a suitable substitute.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Remove pointless decrement of variable, and associated comment.
While i is used subsequently, it is re-initialized so this decrement
serves no purpose.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename numdescs to num_descs to be more consistent with the naming of
other counters and improve readability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename 'filep' and 'filp' to 'file' to be consistent with other use
and improve readability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Refactor the mapping from handle flags to desc flags into a helper
function.
The assign_bit is overkill where it is replacing the set_bit cases, as is
rechecking bits known to be clear in some circumstances, but the DRY
simplification more than makes up for any performance degradation,
especially as this is not a hot path.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Make indentation consistent with other use to improve readability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Sort the includes of gpiolib-cdev.c to make it easier to identify if a
module is included and to avoid duplication.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move gpiolib-sysfs function declarations into their own header.
These functions are in gpiolib-sysfs.c, and are only required by gpiolib.c,
and so should be in a module header, not gpiolib.h.
This brings gpiolib-sysfs into line with gpiolib-cdev, and is another step
towards removing the sysfs inferface.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Sparse cannot peer into other functions to see when and if locks are
acquired and released, thus it simply warns that a 'context imbalance'
is detected instead. Let's be kind to Sparse and let it know that
this behaviour is intentional.
drivers/gpio/gpio-mlxbf2.c:125:12: warning: context imbalance in 'mlxbf2_gpio_lock_acquire' - different lock contexts for basic block
drivers/gpio/gpio-mlxbf2.c:151:13: warning: context imbalance in 'mlxbf2_gpio_lock_release' - unexpected unlock
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Asmaa Mnebhi <asmaa@mellanox.com>
Cc: Asmaa Mnebhi <Asmaa@mellanox.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-11-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
... as is the case when !CONFIG_ACPI.
Fixes the following W=1 kernel build warning:
drivers/gpio/gpio-mlxbf2.c:312:36: warning: ‘mlxbf2_gpio_acpi_match’ defined but not used [-Wunused-const-variable=]
312 | static const struct acpi_device_id mlxbf2_gpio_acpi_match[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Asmaa Mnebhi <asmaa@mellanox.com>
Cc: Asmaa Mnebhi <Asmaa@mellanox.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-10-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
... as is the case when !CONFIG_ACPI.
Fixes the following W=1 kernel build warning:
drivers/gpio/gpio-mlxbf.c:130:36: warning: ‘mlxbf_gpio_acpi_match’ defined but not used [-Wunused-const-variable=]
130 | static const struct acpi_device_id mlxbf_gpio_acpi_match[] = {
| ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Shravan Kumar Ramani <sramani@mellanox.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-9-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kerneldoc expects struct properties to be documented using the syntax
'@.*: ', but no ':' has been provided in 'struct it87_gpio's
header. Add them to stop confusing kerneldoc.
Fixes the following W=1 warnings:
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'chip' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'lock' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'io_base' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'io_size' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'output_base' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'simple_base' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'simple_size' not described in 'it87_gpio'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: "Diego Elio Pettenò" <flameeyes@flameeyes.eu>
Link: https://lore.kernel.org/r/20200630133345.2232932-8-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kerneldoc expects struct properties to be documented using the syntax
'@.*: ', but no '@' has been provided in 'struct syscon_gpio_data's
header. Add them to stop confusing kerneldoc.
Fixes the following W=1 warnings:
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'compatible' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'flags' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'bit_count' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'dat_bit_offset' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'dir_bit_offset' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'set' not described in 'syscon_gpio_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Link: https://lore.kernel.org/r/20200630133345.2232932-7-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No attempt has been made to provide proper descriptions for each of
the function arguments throughout the file. Simply demote all
kerneldoc headers to basic function headers.
Fixes the following W=1 kernel build warnings:
drivers/gpio/gpio-sama5d2-piobu.c:59: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_setup_pin'
drivers/gpio/gpio-sama5d2-piobu.c:59: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_setup_pin'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'mask' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'value' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:97: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_read_value'
drivers/gpio/gpio-sama5d2-piobu.c:97: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_read_value'
drivers/gpio/gpio-sama5d2-piobu.c:97: warning: Function parameter or member 'mask' not described in 'sama5d2_piobu_read_value'
drivers/gpio/gpio-sama5d2-piobu.c:116: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_get_direction'
drivers/gpio/gpio-sama5d2-piobu.c:116: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_get_direction'
drivers/gpio/gpio-sama5d2-piobu.c:131: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_direction_input'
drivers/gpio/gpio-sama5d2-piobu.c:131: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_direction_input'
drivers/gpio/gpio-sama5d2-piobu.c:140: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_direction_output'
drivers/gpio/gpio-sama5d2-piobu.c:140: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_direction_output'
drivers/gpio/gpio-sama5d2-piobu.c:140: warning: Function parameter or member 'value' not described in 'sama5d2_piobu_direction_output'
drivers/gpio/gpio-sama5d2-piobu.c:154: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_get'
drivers/gpio/gpio-sama5d2-piobu.c:154: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_get'
drivers/gpio/gpio-sama5d2-piobu.c:174: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_set'
drivers/gpio/gpio-sama5d2-piobu.c:174: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_set'
drivers/gpio/gpio-sama5d2-piobu.c:174: warning: Function parameter or member 'value' not described in 'sama5d2_piobu_set'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-6-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A good attempt has been made to properly document 'struct
sprd_pmic_eic', but 'map' has been incorrectly described as
'regmap' since the driver's inception in 2018.
Fixes the following W=1 kernel build warning:
drivers/gpio/gpio-pmic-eic-sprd.c:65: warning: Function parameter or member 'map' not described in 'sprd_pmic_eic'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-5-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
