Since the member was dropped from the common Blackfin header, we need
to stop using it in the SPORT driver too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
No other SPI controller has this field, and SPI clients should be setting
this up in their own drivers. So drop it from the Blackfin controller to
keep people from using it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each transfer may have its own bits per word.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This controller is only for blackfin 5xx soc, so rename it to BFIN5XX
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.
To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
bad idea leading to quick interrupt handler re-entrancy
Tested-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A new enum indicating the dma channel direction was introduced by:
commit 49920bc669
dmaengine: add new enum dma_transfer_direction
The following commit changed spi-ep93xx to use the new enum:
commit a485df4b44
spi, serial: move to dma_transfer_direction
In doing so a sparse warning was introduced:
warning: mixing different enum types
int enum dma_data_direction versus
int enum dma_transfer_direction
This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.
Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix kernel-doc warning in spi.h (copy/paste):
Warning(include/linux/spi/spi.h:365): No description found for parameter 'unprepare_transfer_hardware'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check
if (pl022->vendor->max_bpw >= 32)
which must be checking for <=.
Also error print message is incorrect, that prints "range is from 1 to
16".
Fix both these issues.
Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.
We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.
Bug introduced in commit 92ae03f2ef ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up"). On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.
I had actually tested the corner-cases, I had only tested them on
x86-64. Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)
This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way. 'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 26f41062f2 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* A handful of warning and build fixes for Qualcomm MSM
* Build/warning and bug fixes for Samsung Exynos
* A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
* A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=OWRk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
- A handful of warning and build fixes for Qualcomm MSM
- Build/warning and bug fixes for Samsung Exynos
- A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
- A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=8He+
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
Commit 18a4d0a22e ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From David Brown:
"Here are some fixes for msm that fix problems caused by the latest
ARM code. The ones from Daniel remove unneeded fixups that now
cause compilation failures. Mine fix section mismatches, that were
incompletely fixed earlier."
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it. Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).
So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Signed-off-by: Luboš Luňák <l.lunak@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit 81c88a711 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Regulator names should not contain slash to avoid issues with debugfs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When selecting SAMSUNG_PM_DEBUG, it complains about a missing printascii()
function if you do not select DEBUG_LL, so make the former select the latter.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull system.h fixups for less common arch's from Paul Gortmaker:
"Here is what is hopefully the last of the system.h related fixups.
The fixes for Alpha and ia64 are code relocations consistent with what
was done for the more mainstream architectures. Note that the
diffstat lines removed vs lines added are not the same since I've
fixed some of the whitespace issues in the relocated code blocks.
However they are functionally the same. Compile tested locally, plus
these two have been in linux-next for a while.
There is also a trivial one line system.h related fix for the Tilera
arch from Chris Metcalf to fix an implict include.."
* 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
irq_work: fix compile failure on tile from missing include
ia64: populate the cmpxchg header with appropriate code
alpha: fix build failures from system.h dismemberment
It includes:
- a compile fix for au1*fb
- a fix to make kyrofb usable on x86_64
- a fix for uvesafb to prevent an oops due to NX-protection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=PWxJ
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a compile fix for au1*fb
- a fix to make kyrofb usable on x86_64
- a fix for uvesafb to prevent an oops due to NX-protection
"The fix for kyrofb is a bit large but it's just replacing "unsigned
long" by "u32" for 64 bit compatibility."
* tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6:
video:uvesafb: Fix oops that uvesafb try to execute NX-protected page
fbdev: fix au1*fb builds
kyrofb: fix on x86_64
Pull the minimal btrfs branch from Chris Mason:
"We have a use-after-free in there, along with errors when mount -o
discard is enabled, and a BUG_ON(we should compile with UP more
often)."
* 'for-linus-min' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use commit root when loading free space cache
Btrfs: fix use-after-free in __btrfs_end_transaction
Btrfs: check return value of bio_alloc() properly
Btrfs: remove lock assert from get_restripe_target()
Btrfs: fix eof while discarding extents
Btrfs: fix uninit variable in repair_eb_io_failure
Revert "Btrfs: increase the global block reserve estimates"
Pull block driver bits from Jens Axboe:
- A series of fixes for mtip32xx. Most from Asai at Micron, but also
one from Greg, getting rid of the dependency on PCIE_HOTPLUG.
- A few bug fixes for xen-blkfront, and blkback.
- A virtio-blk fix for Vivek, making resize actually work.
- Two fixes from Stephen, making larger transfers possible on cciss.
This is needed for tape drive support.
* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
mtip32xx: dump tagmap on failure
mtip32xx: fix handling of commands in various scenarios
mtip32xx: Shorten macro names
mtip32xx: misc changes
mtip32xx: Add new sysfs entry 'status'
mtip32xx: make setting comp_time as common
mtip32xx: Add new bitwise flag 'dd_flag'
mtip32xx: fix error handling in mtip_init()
virtio-blk: Call revalidate_disk() upon online disk resize
xen/blkback: Make optional features be really optional.
xen/blkback: Squash the discard support for 'file' and 'phy' type.
mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
cciss: Fix scsi tape io with more than 255 scatter gather elements
cciss: Initialize scsi host max_sectors for tape drive support
xen-blkfront: make blkif_io_lock spinlock per-device
xen/blkfront: don't put bdev right after getting it
xen-blkfront: use bitmap_set() and bitmap_clear()
xen/blkback: Enable blkback on HVM guests
xen/blkback: use grant-table.c hypercall wrappers
Pull block core bits from Jens Axboe:
"It's a nice and quiet round this time, since most of the tricky stuff
has been pushed to 3.5 to give it more time to mature. After a few
hectic block IO core changes for 3.3 and 3.2, I'm quite happy with a
slow round.
Really minor stuff in here, the only real functional change is making
the auto-unplug threshold a per-queue entity. The threshold is set so
that it's low enough that we don't hold off IO for too long, but still
big enough to get a nice benefit from the batched insert (and hence
queue lock cost reduction). For raid configurations, this currently
breaks down."
* 'for-3.4/core' of git://git.kernel.dk/linux-block:
block: make auto block plug flush threshold per-disk based
Documentation: Add sysfs ABI change for cfq's target latency.
block: Make cfq_target_latency tunable through sysfs.
block: use lockdep_assert_held for queue locking
block: blk_alloc_queue_node(): use caller's GFP flags instead of GFP_KERNEL
The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.
This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit b09db45c (cpufreq: OMAP driver depends CPUfreq tables.) This
patch remedies that.
Apologies to Russell King for breaking his originally working patch.
Also, thanks to Grazvydas Ignotas for reporting the same problem.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull sparc fixes from David Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
Miscellaneous bug fixes to GPIO drivers and for a corner case in the
gpio device tree parsing code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fdGO
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO bug fixes from Grant Likely:
"Miscellaneous bug fixes to GPIO drivers and for a corner case in the
gpio device tree parsing code."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warning in gpio-samsung.c file
gpio: Fix range check in of_gpio_simple_xlate()
gpio: Fix uninitialized variable bit in adp5588_irq_handler
gpio/sodaville: Convert sodaville driver to new irqdomain API
Miscellaneous driver bug fixes. No major changes in this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tw/j
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI bug fixes from Grant Likely:
"Miscellaneous driver bug fixes. No major changes in this branch."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/imx: prevent NULL pointer dereference in spi_imx_probe()
spi/imx: mark base member in spi_imx_data as __iomem
spi/mpc83xx: fix NULL pdata dereference bug
spi/davinci: Fix DMA API usage in davinci
spi/pL022: include types.h to remove compilation warnings
The invocation of softirq is now handled by irq_exit(), so there is no
need for sparc64 to invoke it on the trap-return path. In fact, doing so
is a bug because if the trap occurred in the idle loop, this invocation
can result in lockdep-RCU failures. The problem is that RCU ignores idle
CPUs, and the sparc64 trap-return path to the softirq handlers fails to
tell RCU that the CPU must be considered non-idle while those handlers
are executing. This means that RCU is ignoring any RCU read-side critical
sections in those handlers, which in turn means that RCU-protected data
can be yanked out from under those read-side critical sections.
The shiny new lockdep-RCU ability to detect RCU read-side critical sections
that RCU is ignoring located this problem.
The fix is straightforward: Make sparc64 stop manually invoking the
softirq handlers.
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The DS driver registers as a subsys_initcall() but this can be too
early, in particular this risks registering before we've had a chance
to allocate and setup module_kset in kernel/params.c which is
performed also as a subsyts_initcall().
Register DS using device_initcall() insteal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
The change
commit 4416e9eb0b
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:12 2010 -0700
arm: msm: Fix section mismatch in smd.c.
fixes a section mismatch between the board file and the smd driver's
probe function, however, it misses the additional mismatches between
the probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
The change
commit 461cbe77d0
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:13 2010 -0700
video: msm: Fix section mismatch in mddi.c.
fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
Fixes the following warnings,
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:71: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout.c:71: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout.c:71: error: for each function it appears in.)
and
arch/arm/mach-msm/board-trout-panel.c: In function 'trout_init_panel':
arch/arm/mach-msm/board-trout-panel.c:267: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout-panel.c:267: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout-panel.c:267: error: for each function it appears in.)
This came in with the following commit 9f97da78bf
which removes asm/system.h
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
cc: David Howells <dhowells@redhat.com>
cc: Bryan Huntsman <bryanh@codeaurora.org>
cc: linux-arm-msm@vger.kernel.org
cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David Brown <davidb@codeaurora.org>
This old fixup causes a build failure, so I remove it just like in
trout.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
