Two changes are necessary to enable proper operation of the DM9000 device with
the Colibri PXA 270 board: firstly, the IRQ type needs to be configured for
rising edge interrupts, and secondly this configuration needs to be
communicated through to the DM9000.
[akpm@linux-foundation.org: remove set_irq_type() call as per ben-linux request]
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Daniel Mack <daniel@caiaq.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Whereas most Orion 5x machine support code would initialise the PCI
subsystem with nr_controllers in their struct hw_pci set to 2, the
DNS323 and Kurobox Pro machine support code had nr_controllers set
to 1.
This was presumably done because on those two machines, the PCI(-X)
controller (nr == 1) isn't used, requiring initialisation of only
the PCIe controller (nr == 0.) However, not initialising the PCI(-X)
controller on boards that don't use it leads to a situation where
both the PCIe and the PCI(-X) controller think that their root bus is
zero, and it messes up IRQ assignment.
This patch changes the DNS323 and Kurobox Pro support code to always
use nr_controllers == 2.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU's dma_flush_range() operation needs to clean+invalidate the
given memory area if the cache is in writeback mode, or do just the
invalidate part if the cache is in writethrough mode, but the current
proc-arm{925,926,940,946} (incorrectly) do a cache clean in the
latter case. This patch fixes that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Martin Michlmayr reported that fuse complains:
ERROR: "copy_page" [fs/fuse/fuse.ko] undefined!
so export the needed function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irqs.h:
* rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND
locomo.h:
* add some definition for locomo spi controller
* correct some errors
locomo.c:
* correct some errors
* add set_type for locomo gpio irq chip
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: disable mwait for AMD family 10H/11H CPUs
x86: fix crash on cpu hotplug on pat-incapable machines
x86: remove mwait capability C-state check
The previous revert of 0c07ee38c9 left
out the mwait disable condition for AMD family 10H/11H CPUs.
Andreas Herrman said:
It depends on the CPU. For AMD CPUs that support MWAIT this is wrong.
Family 0x10 and 0x11 CPUs will enter C1 on HLT. Powersavings then
depend on a clock divisor and current Pstate of the core.
If all cores of a processor are in halt state (C1) the processor can
enter the C1E (C1 enhanced) state. If mwait is used this will never
happen.
Thus HLT saves more power than MWAIT here.
It might be best to switch off the mwait flag for these AMD CPU
families like it was introduced with commit
f039b75471 (x86: Don't use MWAIT on AMD
Family 10)
Re-add the AMD families 10H/11H check and disable the mwait usage for
those.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
pat_disable() is __init, which means it goes away after booting is complete.
Unfortunately it is used by the hotplug code if the machine is not
pat-capable, causing a crash.
Fix by marking pat_disable() as __cpuinit.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Vegard Nossum reports:
| powertop shows between 200-400 wakeups/second with the description
| "<kernel IPI>: Rescheduling interrupts" when all processors have load (e.g.
| I need to run two busy-loops on my 2-CPU system for this to show up).
|
| The bisect resulted in this commit:
|
| commit 0c07ee38c9
| Date: Wed Jan 30 13:33:16 2008 +0100
|
| x86: use the correct cpuid method to detect MWAIT support for C states
remove the functional effects of this patch and make mwait unconditional.
A future patch will turn off mwait on specific CPUs where that causes
power to be wasted.
Bisected-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes the missing ram regression reported by
Mikael Pettersson <mikpe@it.uu.se>, much thanks for
all of this help in diagnosing this.
The second argument to lmb_reserve() is a size,
not an end address bounds.
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] macintosh: Replace deprecated __initcall with device_initcall
[POWERPC] cell: Fix section mismatches in io-workarounds code
[POWERPC] spufs: Fix compile error
[POWERPC] Fix uninitialized variable bug in copy_{to|from}_user
[POWERPC] Add null pointer check to of_find_property
[POWERPC] vmemmap fixes to use smaller pages
[POWERPC] spufs: Fix pointer reference in find_victim
[POWERPC] 85xx: SBC8548 - Add flash support and HW Rev reporting
[POWERPC] 85xx: Fix some sparse warnings for 85xx MDS
[POWERPC] 83xx: Enable DMA engine on the MPC8377 MDS board.
[POWERPC] 86xx: mpc8610_hpcd: fix second serial port
[POWERPC] 86xx: mpc8610_hpcd: add support for NOR and NAND flashes
[POWERPC] 85xx: Add 8568 PHY workarounds to board code
[POWERPC] 86xx: mpc8610_hpcd: use ULI526X driver for on-board ethernet
The patch aims to fix a performance issue for the syscall
personality(PER_LINUX32).
On IA-64 box, the syscall personality (PER_LINUX32) has poor performance
because it failed to find the Linux/x86 execution domain. Then it tried
to load the kernel module however it failed always and it used the default
execution domain PER_LINUX instead. Requesting kernel modules is very
expensive. It caused the performance issue. (see the function
lookup_exec_domain in kernel/exec_domain.c).
To resolve the issue, execution domain Linux/x86 is always registered in
initialization time for IA-64 architecture.
Signed-off-by: Xiaolan Huang <xiaolan.huang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] show_interrupts: prevent cpu hotplug when walking cpu_online_map.
[S390] smp: __smp_call_function_map vs cpu_online_map fix.
[S390] tape: Use ccw_dev_id to build cdev_id.
[S390] dasd: fix timeout handling in interrupt handler
[S390] s390dbf: Use const char * for dbf name.
[S390] dasd: Use const in busid functions.
[S390] blacklist.c: removed duplicated include
[S390] vmlogrdr: module initialization function should return negative errors
[S390] sparsemem vmemmap: initialize memmap.
[S390] Remove last traces of cio_msg=.
[S390] cio: Remove CCW_CMD_SUSPEND_RECONN in front of CCW_CMD_SET_PGID.
Surround all the code withing show_interrupts() with
get/put_online_cpus() to prevent strange results wrt cpu hotplug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Both smp_call_function() and __smp_call_function_map() access
cpu_online_map. Both functions run with preemption disabled which
protects for cpus going offline. However new cpus can be added and
therefore the cpu_online_map can change unexpectedly.
So use the call_lock to protect against changes to the cpu_online_map
in start_secondary() and all smp_call_* functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We should use const char * for passing the name of the debug feature
around since it will not be changed.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let's just use the generic vmmemmap_alloc_block() function which
always returns initialized memory.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The functions time_before, time_before_eq, time_after, and time_after_eq are
more robust for comparing jiffies against other values.
So use the time_after() macro, defined in linux/jiffies.h, which deals with
wrapping correctl
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.
The two outputs only differ in text formatting:
printk("Free swap = %lukB\n", ...);
printk("Free swap: %6ldkB\n", ...);
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This trivial patch fixes the following section warnings on PARISC:
> WARNING: vmlinux.o (.text.1): unexpected section name.
>The (.[number]+) following section name are ld generated and not expected.
> Did you forget to use "ax"/"aw" in a .S file?
> Note that for example <linux/init.h> contains
> section definitions for use in .S files.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix following warnings:
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0x9c): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.iowa_register_bus()
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0xa4): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.io_workaround_init()
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With CONFIG_VIRT_CPU_ACCOUNTING disabled, I got the following error:
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c: In function 'spu_switch_log_notify':
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c:2542: error: implicit declaration of function 'get_tb'
make[4]: *** [arch/powerpc/platforms/cell/spufs/file.o] Error 1
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes vmemmap to use a different region (region 0xf) of the
address space, and to configure the page size of that region
dynamically at boot.
The problem with the current approach of always using 16M pages is that
it's not well suited to machines that have small amounts of memory such
as small partitions on pseries, or PS3's.
In fact, on the PS3, failure to allocate the 16M page backing vmmemmap
tends to prevent hotplugging the HV's "additional" memory, thus limiting
the available memory even more, from my experience down to something
like 80M total, which makes it really not very useable.
The logic used by my match to choose the vmemmap page size is:
- If 16M pages are available and there's 1G or more RAM at boot,
use that size.
- Else if 64K pages are available, use that
- Else use 4K pages
I've tested on a POWER6 (16M pages) and on an iSeries POWER3 (4K pages)
and it seems to work fine.
Note that I intend to change the way we organize the kernel regions &
SLBs so the actual region will change from 0xf back to something else at
one point, as I simplify the SLB miss handler, but that will be for a
later patch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If victim (not ctx) is in spu_run, add victim to rq.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Use a TS_RESTORE_SIGMASK
lmb: Make lmb debugging more useful.
lmb: Fix inconsistent alignment of size argument.
sparc: Fix mremap address range validation.
Add a common hex array in hexdump.c so everyone can use it.
Add a common hi/lo helper to avoid the shifting masking that is
done to get the upper and lower nibbles of a byte value.
Pull the pack_hex_byte helper from kgdb as it is opencoded many
places in the tree that will be consolidated.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.
This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.
It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
acpi_unregister_gsi() should "undo" what acpi_register_gsi() does.
On systems that have legacy interrupts, acpi_unregister_gsi erroneously calls
iosapci_unregister_intr() which is wrong to do and causes a loud warning.
acpi_unregister_gsi() should just return in these cases.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is only palinfo_handle_smp as (indirect) user of palinfo_smp_call (by
way of smp_call_function_single) and surely palinfo_handle_smp never pass
NULL as parameter for info.
Signed-off-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a typo, and coding style cleanups for pfm_handle_work().
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch does:
- make comment at next to resched check more robust
- move "re-check" comments to next to where change predicate regs
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[Bug-fix for "[BUG?][2.6.25-mm1] sleeping during IRQ disabled"]
This patch does:
- enable interrupts before calling schedule() as same as others, ex. x86
- enable interrupts during ia64_do_signal() and ia64_sync_krbs()
- do_notify_resume_user() is still called with interrupts disabled, since
we can take short path of fsys_mode if-statement quickly.
- pfm_handle_work() is also called with interrupts disabled, since
it can deal interrupt mask within itself.
- fix/add some comments/notes
Reported-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The sequence executed in check_sal_cache_flush:
- pend a timer interrupt
- call SAL_CACHE_FLUSH
- see if interrupt is still pending
can hang HP machines with buggy SAL_CACHE_FLUSH implementations.
Provide a kernel command-line argument to allow users skip this
check if desired. Using this parameter will force ia64_sal_cache_flush
to call ia64_pal_cache_flush() instead of SAL_CACHE_FLUSH.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some IA64 machines map all cell-local memory above 4 GB (32 bit limit).
However, in most cases, the kernel needs some memory below that limit that is
DMA-capable. So in this machine configuration, the crashkernel will be reserved
above 4 GB.
For machines that use SWIOTLB implementation because they lack an I/O MMU
the low memory is required by the SWIOTLB implementation. In that case,
it doesn't make sense to reserve the crashkernel at all because it's unusable
for kdump.
A special case is the "hpzx1" machine vector. In theory, it has a I/O MMU, so
it can be booted above 4 GB. However, in the kdump case that is not possible
because of changeset 51b58e3e26:
On HP zx1 machines, the 'machvec=dig' parameter is needed for the kdump
kernel to avoid problems with the HP sba iommu. The problem is that during
the boot of the kdump kernel, the iommu is re-initialized, so in-flight DMA
from improperly shutdown drivers causes an IOTLB miss which leads to an
MCA. With kdump, the idea is to get into the kdump kernel with as little
code as we can, so shutting down drivers properly is not an option.
The workaround is to add 'machvec=dig' to the kdump kernel boot parameters.
This makes the kdump kernel avoid using the sba iommu altogether, leaving
the IOTLB intact. Any ongoing DMA falls harmlessly outside the kdump
kernel. After the kdump kernel reboots, all devices will have been
shutdown properly and DMA stopped.
This patch pushes that functionality into the sba iommu initialization
code, so that users won't have to find the obscure documentation telling
them about 'machvec=dig'.
This means that also for hpzx1 it's not possible to boot when all
memory is above the 4 GB limit. So the only machine vectors that can handle
this case are "sn2" and "uv".
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds the basic IA64 machvec infrastructure to support
the SGI "UV" platform.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
ACPI/PCI: another multiple _OSC memory leak fix
x86/PCI: X86_PAT & mprotect
PCI: enable nv_msi_ht_cap_quirk for ALi bridges
PCI: Make the intel-iommu_wait_op macro work when jiffies are not running
ACPI/PCI: handle multiple _OSC
ACPI/PCI: handle multiple _OSC
x86/PCI: fix broken ISA DMA
PCI ACPI: fix uninitialized variable in __pci_osc_support_set
The user_regset_view table for the 32-bit regsets on the 64-bit build had
the wrong sizes for the FP regsets. This bug had no user-visible effect
(just on kernel modules using the user_regset interfaces and the like).
But the fix is trivial and risk-free.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
