According to the IB spec, a QP can be moved from RESET back to RESET
or to the ERROR state, but mlx4 firmware does not support this and
returns an error if we try. Fix the RESET to RESET transition by
just returning 0 without doing anything, and fix RESET to ERROR by
moving the QP from RESET to INIT with dummy parameters and then
transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the IB spec, a QP can be moved from RESET to the ERROR
state, but mthca firmware does not support this and returns an error if
we try. Work around this FW limitation by moving the QP from RESET to
INIT with dummy parameters and then transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Global CM packets used by rmda_cm were being sent with a GRH:hopLimit
of zero, causing them to be dropped by the router. The problem is a
missing initialization of the hop_limit field in mthca_read_ah(),
which was called by build_mlx_header() when sending a MAD on QP1.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
max_qp_dest_rdma is already in natural units - no need to shift. This
was discovered by a test that deliberately requests more outstanding
atomic operation than the device supports.
Found by Sagi Rotem at Mellanox.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the return code of ehca_register_mr() to ENOMEM if the corresponding
firmware call fails due to out of resources. Some other error codes
were explicitly mapped to EINVAL -- just remove those cases so they
get mapped to the default case, which already returns EINVAL anyway.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SM reconfiguration or failover possibly causes a shuffling of the values
in the P_Key table. Right now, IPoIB only queries for the P_Key index
once when it creates the device QP, and hence there are problems if the
index of a P_Key value changes. Fix this by using the PKEY_CHANGE event
to trigger a recheck of the P_Key index.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up ib_query_port() and ib_modify_port() slightly by using the
just-added start_port() and end_port() helpers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add ib_find_gid() and ib_find_pkey() functions that use uncached device
queries. The calls might block but the returns are always up-to-date.
Cache P_Key and GID table lengths in core to avoid extra port info queries.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep found the following potential deadlock between mcast_lock and
n_mcast_grps_lock: mcast_lock is taken from both interrupt context and
process context, so spin_lock_irqsave() must be used to take it.
n_mcast_grps_lock is only taken from process context, so at first it
seems safe to take it with plain spin_lock(); however, it also nests
inside mcast_lock, and hence we could deadlock:
cpu A cpu B
ipath_mcast_add():
spin_lock_irq(&mcast_lock);
ipath_mcast_detach():
spin_lock(&n_mcast_grps_lock);
<enter interrupt>
ipath_mcast_find():
spin_lock_irqsave(&mcast_lock);
spin_lock(&n_mcast_grps_lock);
Fix this by using spin_lock_irq() to take n_mcast_grps_lock.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Free umem when task's mm is already destroyed by the time
ib_umem_release gets called.
Found by Dotan Barak at Mellanox.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix an Oops in the cciss driver caused by system shutdown while a filesystem
on a cciss device is still active. The cciss_remove_one function only
properly removes the device if the device has been cleanly released by its
users, which is not the case when the pci_driver.shutdown method is called.
This patch adds a new cciss_shutdown function to better match the pattern
used by various SCSI drivers: deactivate device interrupts and flush caches.
It also alters the cciss_remove_one function to match and readds the
__devexit annotation that was removed when cciss_remove_one was serving as
the pci_driver.shutdown method.
Signed-off-by: Gerald Britton <gbritton@alum.mit.edu>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] tcrypt: Add missing error check
[CRYPTO] padlock: Make CRYPTO_DEV_PADLOCK a tristate again
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (32 commits)
[POWERPC] Remove build warnings in windfarm_core
[POWERPC] Pass per-file CFLAGs for platform specific op codes
[POWERPC] Correct #endif comment
[POWERPC] Fix ppc_rtas_progress_show()
[POWERPC] Fix sed command lines for zlib source construction
[POWERPC] Specify GNUTARGET on $(AR) invocations
[POWERPC] Make sure device node type/name is not NULL on hot-added nodes
[POWERPC] Small fixes for the Ebony device tree
[POWERPC] Fix warning on UP
[POWERPC] cell_defconfig: Disable cpufreq and pmi
[POWERPC] Fix IO space on PCI buses created from of_platform
[POWERPC] Add spinlock to request_phb_iospace()
[POWERPC] Fix make rules for treeImage.initrd
[POWERPC] Remove warning in mpic.c
[POWERPC] Update pasemi_defconfig
[POWERPC] pasemi: CONFIG_GENERIC_TBSYNC no longer needed
[POWERPC] Update iseries_defconfig
[POWERPC] Wire up some more syscalls
[POWERPC] Fix bug adding properties with flatdevtree.c's ft_set_prop()
[POWERPC] Remove fixup_bigphys_addr() for arch/powerpc to avoid link error
...
Turning it into a boolean was unnecessary and caused ALGAPI to be
pinned down as a boolean to. This patch makes it a tristate again.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With STANDBYDOWN tracking added, libata.spindown_compat isn't
necessary anymore. If userspace shutdown(8) issues STANDBYNOW, libata
warns. If userspace shutdown(8) doesn't issue STANDBYNOW, libata does
the right thing. Userspace can tell whether kernel supports spindown
by testing whether sysfs node manage_start_stop exists as before.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As with all other drivers, sata_nv's hpriv is allocated with
devm_kzalloc() and there's no need to free it explicitly. Kill
nv_remove_one() which incorrectly used kfree() instead of devm_kfree()
and use ata_pci_remove_one() directly.
Original fix is from Peer Chen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv
driver is unnecessary. Also the wildcard sometimes cause sata_nv driver to
be loaded for AHCI controllers,which is not as expected.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_msi failure is a normal event so we should not print any error.
Going over the code I spotted a missing pci_disable_msi() leak when irq
allocation fails. The whole code also needed a cleanup, so I combined the
two different calls to pci_request_irq into a single call making this
look a lot better. All #ifdef CONFIG_PCI_MSI's have been removed.
Compile tested with both CONFIG_PCI_MSI enabled and disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_msi calls can fail for normal operational reasons. Driver
should not print an error message in that case. Fix a leak that leaves
msi enabled if pci_request_irq fails. We can remove CONFIG_PCI_MSI
ifdefs alltogether
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix for driver on System-p
This patch will fix a ping issue on system-p
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Adhiraj Joshi <adhiraj@netxen.com>
Signed-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spidernet was the driver I original did all the node-aware netdevice
allocation for, but after a year it still hasn't hit mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware must not see that is given ownership of a buffer until it is
completely written, and when the driver receives ownership of a buffer,
it must ensure that any other reads to the buffer reflect its final
state. Thus, I/O barriers are added where required.
Without this patch, I have observed GCC reordering the setting of
bdp->length and bdp->status in gfar_new_skb. Hardware reordering
was also theoretically possible.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix link speed detection change.
Thanks to Stefan Roese <sr@denx.de> for finding this bug.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Original patch is from Jeff Haran <jharan@brocade.com> with my minor style
fixes. His comments follow:
The first problem was in the function that configures the PHY for
autonegotiation, genmii_setup_aneg(). The original code does a
read/modify/write of the autonegotiation advertizement register (reg 4),
followed by a read/modify/write of the control register (reg 0). While
the original code follows the proper procedure as per reading the IEEE
specs, what I found is that on at least one PHY model (National DP83843)
the read of the control register comes back with the soft reset bit set
(bit 15). Because of the read/modify/write operation, this causes the
write to write a 1 back to the reset bit, which initiates a software
reset of the PHY. This software reset causes the PHY to return to its
power up state which advertizes all modes of operation, thus negating
the write to the autoneg advertizement register. The modification is to
spin reading the control register until the soft reset bit is clear
before doing the modify/write.
The second problem was in the function that configures the PHY for
forced operation, genmii_setup_forced(). The original code initiates a
software reset operation via a write of a 1 to bit 15 of the control
register (reg 0), but then proceeds to do a second write to that same
register without waiting until that reset bit is cleared by the PHY
itself (which according to the IEEE specs indicates that the PHY reset
is complete). This is a violation of how one is supposed to use this
software reset feature of these PHYs and I believe was the cause of
mysterious, difficult to reproduce link failures that we've observed on
some of our systems that use this driver. The fix is to modify the
function so that it spins waiting for the reset bit to clear after doing
the soft reset and before doing the subsequent write.
Signed-off-by: Jeff Haran <jharan@brocade.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: Stephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.
This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.
It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.
[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make drivers/rtc/Kconfig be clearer about what the various "interfaces"
actually mean, by showing path names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typo which breaks build. How did that happen?
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refine SCREEN_INFO sanity check for vgacon initialization.
Checking video mode field only to see whenever SCREEN_INFO is
initialized is not enougth, in some cases it is zero although
a vga card is present. Lets additionally check cols and lines.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Strip __cpuinit[data] from Node <-> PXM routines and supporting data
structures. Also make pxm_to_node_map and node_to_pxm_map local to the
numa acpi module.
This fixes a bug triggered by the following conditions:
- boot on a machine with a SLIT table defined
- kernel is configured w/ CONFIG_HOTPLUG_CPU=n
- cat /sys/devices/system/node/node*/distance
This will cause an oops by calling into a freed memory section.
In particular, on x86_64, __node_distance calls node_to_pxm().
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/macintosh/windfarm_core.c: In function 'wf_register_control':
drivers/macintosh/windfarm_core.c:219: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/windfarm_core.c: In function 'wf_register_sensor':
drivers/macintosh/windfarm_core.c:329: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The early kernel parameter is wdt and not wdt_enable. according to
arch/powerpc/kernel/setup_32.c.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: track spindown status and skip spindown_compat if possible
libata: fix shutdown warning message printing
libata-acpi: add ATA_FLAG_ACPI_SATA port flag
libata: during revalidation, check n_sectors after device is configured
libata: separate out ata_dev_reread_id()
pata_scc had been missed by ata_std_prereset() switch
alpha:
drivers/parport/parport_pc.c: In function 'parport_pc_fifo_write_block_dma':
drivers/parport/parport_pc.c:636: warning: implicit declaration of function 'dma_map_single'
drivers/parport/parport_pc.c:637: error: 'DMA_TO_DEVICE' undeclared (first use in this function)
drivers/parport/parport_pc.c:637: error: (Each undeclared identifier is reported only once
drivers/parport/parport_pc.c:637: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_first_zero_bit accepts number of bits, not longs.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
http://bugzilla.kernel.org/show_bug.cgi?id=8469
As discussed in the bugzilla outlined below, we have an sa based
(Mustang) RAID adapter on the system, a Dell PERC2/QC. Affected
controllers are HP NetRAID, Adaptec AAC-364, Dell PERC2/QC or Adaptec
5400S. This problem coincides with the introduction of the adapter_comm
and adapter_deliver platform functions (Message [PATCH 1/4] aacraid:
rework communication support code, January 23 2007, which initially
migrated to 2.6.21)
The panic occurs with an uninitialized adapter_deliver platform function
pointer. The enclosed patch, unmodified as tested by Rainer, solves the
problem.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This sets sg_dma_len to a proper value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add debug information into abort and host_reset routine.
Change ioremap to ioremap_nocache.
Version updated to 3.6.0000.1.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After reset completed, the scsi error handler sends out TEST_UNIT_READY
to the device. For 'normal' devices the command will be handled by firmware.
However, because the RAID console only interfaces to scsi mid layer, the
firmware will not process the command for it. This will make the console to
be offlined right after reset. Add the handling in driver to fix this problem.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During hard bus reset of st_shasta controllers, 1 ms is not enough for
16-port controllers, although it's good for 8-port controllers. Extend the
wait time to 100 ms to allow bus resets finish successfully.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The correct internal mapping of stex controllers should be:
id:0~15, lun:0~7 (st_shasta)
id:0, lun:0~127 (st_yosemite)
id:0~127, lun:0 (st_vsc and st_vsc1)
This patch reports the internal mapping to scsi mid layer, eliminating
the translation between scsi mid layer and firmware. To achieve this
goal, we also need to:
-- fail the REPORT_LUNS command for st_shasta because the
firmware is known to not report all actual luns
-- add an entry in scsi_devindo.c to force sequential lun scan
(for st_shasta controllers)
-- fail the REPORT_LUNS command for console device
-- remove special handling of REPORT_LUNS command for
st_yosemite, as there is no translation mapping now
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently ipr always returns success from eh_dev_reset when
called for a SATA device. If ata_do_eh is unable to recover
for some reason, this can result in commands that are still
outstanding when ata_do_eh returns. Change ipr to verify no
commands are outstanding before returning success.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A fix for a really stupid typo in the KS8695 serial driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IO stall after deleting and path checker changes after reenabling zfcp device
Setting one zfcp device offline using chccwdev in a multipath
environment and waiting will lead to IO stall on all paths.
After setting the zfcp device back online using chccwdev,
the devices with io stall will have a different path checker.
Devices corresponding to the deleted units are never freed.
This has the effect that 'slave_destroy' is never called and zfcp
still thinks that this unit is registered
(ZFCP_STATUS_UNIT_REGISTERED is still set). Hence the erp
routine is not called correctly and the unit is not enabled properly.
Do not delete rport and the sdev. Just set the host to block on
'offline'. Setting host online again will then remove the blocked status
and everything is fine again.
Signed-off-by: Michael Loehr <mloehr2@linux.vnet.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
avoid clutter in erp_dbf
cleanup zfcp_fsf_req_dismiss functions:
- avoid clutter in erp_dbf (reqs_active is always 0)
- fold called three-line function into calling function
- add meaningful comment
- coding style
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Our assumption that most distros issue STANDBYNOW seems wrong. The
upstream sysvinit and thus many distros including gentoo and opensuse
don't take any action for libata disks on spindown. We can skip
compat handling for these distros so that they don't need to update
anything to take advantage of kernel-side shutdown.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unlocking ap->lock and ssleeping don't work because SCSI commands can
be issued from completion path without context. Reimplement delayed
completion by allowing translation functions to override
qc->scsidone(), storing the original completion function to
scmd->scsi_done() and overriding qc->scsidone() with a function which
schedules delayed invocation of scmd->scsi_done().
This isn't pretty at all but all the ugly parts are thankfully
contained in the stop translation path where the compat feature is
implemented.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whether a controller needs IDE or SATA ACPI hierarchy is determined by
the programming interface of the controller not by whether the
controller is SATA or PATA, or it supports slave device or not. This
patch adds ATA_FLAG_ACPI_SATA port flags which tells libata-acpi that
the port needs SATA ACPI nodes, and sets the flag for ahci and
sata_sil24.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Device might be resized during ata_dev_configure() due to HPA or
(later) ACPI _GTF. Currently it's worked around by caching n_sectors
before turning off HPA. The cached original size is overwritten if
the device is reconfigured without being hardreset - which always
happens after configuring trasnfer mode. If the device gets hardreset
for some reason after that, revalidation fails with -ENODEV.
This patch makes size checking more robust by moving n_sectors check
from ata_dev_reread_id() to ata_dev_revalidate() after the device is
fully configured. No matter what happens during configuration, a
device must have the same n_sectors after fully configured to be
treated as the same device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_dev_reread_id() from ata_dev_revalidate().
ata_dev_reread_id() reads IDENTIFY page and determines whether the
same device is still there. ata_dev_revalidate() reconfigures after
reread completes. This will be used by ACPI update.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hypervisor interfaces need to be negotiated in order to use
some API calls reliably. So add a small set of interfaces
to request API versions and query current settings.
This allows us to fix some bugs in the hypervisor console:
1) If we can negotiate API group CORE of at least major 1
minor 1 we can use con_read and con_write which can improve
console performance quite a bit.
2) When we do a console write request, we should hold the
spinlock around the whole request, not a byte at a time.
What would happen is that it's easy for output from
different cpus to get mixed with each other.
3) Use consistent udelay() based polling, udelay(1) each
loop with a limit of 1000 polls to handle stuck hypervisor
console.
Signed-off-by: David S. Miller <davem@davemloft.net>
.. because video-buf.c requires PCI, and VIDEO_EM28XX selects it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
stuff that does select USB should depend on USB_ARCH_HAS_HCD, or we'll
end up with unbuildable configs.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
need it for page_private(), not all targets have it pulled indirectly
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
Use menuconfig objects: IDE
sl82c105: Switch to ref counting API
ide: remove ide_use_dma()
ide: add missing validity checks for identify words 62 and 63
ide: remove ide_dma_enable()
sl82c105: add speedproc() method and MWDMA0/1 support
cs5530/sc1200: add ->speedproc support
cs5530/sc1200: DMA support cleanup
ide: use ide_tune_dma() part #2
cs5530/sc1200: add ->udma_filter methods
ide: always disable DMA before tuning it
pdc202xx_new: use ide_tune_dma()
alim15x3: use ide_tune_dma()
sis5513: PIO mode setup fixes
serverworks: PIO mode setup fixes
pdc202xx_old: rewrite mode programming code (v2)
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Not sure how this one got missed in the great purge some time ago but it did.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add the speedproc() method for setting transfer modes, modify config_for_dma()
to call it and use ide_max_dma_mode() to select the best DMA mode.
Add support for the multiword DMA modes 0 and 1, using the upper half of the
'drive_data' field to store the DMA timings to program into the drive control
register when DMA is turned on for real.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add {cs5530,sc1200}_tunepio() for programming PIO timings
* add {cs5530,sc1200}_tune_chipset() (->speedproc method) for setting
transfer mode and convert {cs5530,sc1200}_config_dma() to use it
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
sc1200.c:
* remove open-coded variant of ide_dma_host_off() (== ->dma_host_off),
it is not needed because ->dma_off_quietly calls ->dma_host_off
* use ->dma_host_on (== ide_dma_host_on() for this driver) instead of
open-coded variant, call it from the users of sc1200_config_dma2()
[ there is no need to call ->dma_host_on in sc1200_config_dma() because
core code takes care of calling ->ide_dma_on on successful execution
of ->ide_dma_check ]
* add comment about ->tuneproc interface abuse
cs5530.c/sc1200.c:
* core code takes care of calling ->dma_off_quietly before calling
->ide_dma_check so there is no need to call it in ->ide_dma_check methods
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CS5530/SC1200 specifies that two drives on the same cable cannot mix
UDMA/MDMA. Add {cs5530,sc1200}_udma_filter() to handle this. This also
makes it possible to remove open-coded best DMA mode selection and use
standard ide_use_dma()/ide_max_dma_mode() helpers. While at it bump
version numbers.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted). Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove code enabling IORDY and prefetch from config_chipset_for_dma(),
as the comment states it has no real effect because these settings are
overriden when the PIO mode is set (and for this driver ->autotune == 1
so PIO mode is always programmed)
* use ide_tune_dma() in pdcnew_config_drive_xfer_rate() and remove no longer
needed config_chipset_for_dma()
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma(). Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to program PIO5 by config_art_rwp_pio() could result in incorrect PIO
timings being programmed and possibly the data corruption (for < ATA100
family chipsets PIO0 timings were used, for ATA100 and ATA100a - the random
content of test1 variable was used, for ATA133 - MWDMA0 timings were used)
* BUG() in sis5513_tune_chipset() if somebody tries to force unsupported PIO5,
also cleanup this function a bit while at it
* add comment about PIO0 timings for < ATA100 family chipsets
* remove open-coded best PIO mode selection from config_art_rwp_pio(),
it contained numerous bugs:
- it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
before using them
- it tried to found out maximum PIO mode basing on minimum IORDY cycle time
(moreover wrong cycle times were used for PIO1/5)
- it was overriding PIO blacklist and conservative PIO "downgrade" done
by ide_get_best_pio_mode()
* use sis5513_tune_drive() instead of config_art_rwp_pio()
in sis5513_config_xfer_rate() so the correct PIO mode is also set
on drive even if the device is not IORDY/DMA capable
* config_art_rwp_pio() was always setting the best possible mode and not
the wanted one - fix it and move ide_get_best_pio_mode() call to
config_chipset_for_pio()
* don't use ide_find_best_mode() in config_chipset_for_pio(), it was being
overriden by config_art_rwp_pio() for the host timings anyway + we need to
set the same PIO mode on the device and the host
* pass correct "pio" argument (255 instead of 5) to sis5513_tune_drive() call
in sis5513_config_xfer_rate() so the best PIO mode is set on the drive
and not PIO4
* rename sis5513_tune_drive() to sis5513_tuneproc()
and config_chipset_for_pio() to sis5513_tune_driver()
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
timings being programmed and possibly the data corruption (it seems that
the minimum possible values were used but I lack the datasheets to be sure)
* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
when doing PIO autotuning (pio == 255)
* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
takes care of PIO tuning if no suitable DMA mode is found)
* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
config_chipset_for_pio() contained numerous bugs when selecting PIO mode
(luckily it was only used for devices limited to PIO by capabilities/BIOS):
- it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
before using them
- it tried to found out maximum PIO mode basing on minimum IORDY cycle time
(moreover wrong cycle times were used for PIO0/1/5)
- it was overriding PIO blacklist and conservative PIO "downgrade" done
by ide_get_best_pio_mode()
- if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
(XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
was the same as if using XFER_PIO_5 => wrong PIO timings were set)
- it was overriding drive->current_speed
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.
Rewrite mode programming code:
* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
even if both devices on the channel are not DMA capable and after reset
* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
as they need to be setup correctly also for PIO only devices, plus IORDY
wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
ATAPI devices
* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
(driver sets ->autotune to 1 so PIO modes are always programmed => lower
nibble of register A never equals 4 => "chipset_is_set" is always true)
* enable PIO mode programming for all ATAPI devices
(it was limited to ->media == ide_cdrom devices)
* remove extra reads of registers A/B/C, don't read register D et all
* do clearing / programming of registers A/B/C in one go
(gets rid of extra PCI config space read/write cycle)
* set initial values of drive_conf/AP/BP/CP variables to zero
(paranoia for the case when PCI reads fail)
* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
(ide_rate_filter() takes care of it)
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
* add FIXME comment about missing locking for 66MHz clock register
Also while at it:
* remove unused defines
* do a few cosmetic / CodingStyle fixes
* bump driver version
v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
registers is used only by the debugging code so cover "drive_conf"
PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
(Noticed by Sergei Shtylyov)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It was agreed that phy-connection-type was a better name for
the interface-type property, so this patch renames it.
Also, the max-speed property name was determined too generic,
and is therefore eliminated in favour of phy-connection-type
derivation logic.
includes corrections to copyright text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Looks like the new version of this patch has been overlooked,
so I'm resending it.
It just adapts the driver to the new IRQ API
according to what Russell has pointed out.
drivers/net/smc911x.c | 6 ++----
1 files changed, 2 insertions(+), 4 deletions(-)
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out we have an old version of firmware that stores the mac address
in 'mac-address' as a string instead of a byte array. All versions that
use local-mac-address should have it as byte array, so no need to do
string parsing for that case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This caused some very interesting behaviour depending on what happened to
be built at the same time. Add terminating empty entry to the list of IDs.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Interrupt ack fixes
Fix the packet count resets at interrupt time, using the cacheable
packet count status to set number of processed/received packets, since
the ack count is the cumulative number of packets processed, and not
incremental.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some shift values were obviously wrong. Fix them to correspond with
the masks.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB/cm: Optimize stale connection detection
IB/mthca: Set cleaned CQEs back to HW ownership when cleaning CQ
IB/mthca: Fix posting >255 recv WRs for Tavor
RDMA/cma: Add check to validate that cm_id is bound to a device
RDMA/cma: Fix synchronization with device removal in cma_iw_handler
RDMA/cma: Simplify device removal handling code
IB/ehca: Disable scaling code by default, bump version number
IB/ehca: Beautify sysfs attribute code and fix compiler warnings
IB/ehca: Remove _irqsave, move #ifdef
IB/ehca: Fix AQP0/1 QP number
IB/ehca: Correctly set GRH mask bit in ehca_modify_qp()
IB/ehca: Serialize hypervisor calls in ehca_register_mr()
IB/ipath: Shadow the gpio_mask register
IB/mlx4: Fix uninitialized spinlock for 32-bit archs
mlx4_core: Remove unused doorbell_lock
net: Trivial MLX4_DEBUG dependency fix.
This reverts commit f64da958df.
Andi Kleen is unhappy with the changes, and they really do not seem
worth it. IPMI could use DIE_NMI_IPI instead of the new callback, even
though that ends up having its own set of problems too, mainly because
the IPMI code cannot really know the NMI was from IPMI or not.
Manually fix up conflicts in arch/x86_64/kernel/traps.c and
drivers/char/ipmi/ipmi_watchdog.c.
Cc: Andi Kleen <ak@suse.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Corey Minyard <minyard@acm.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the presence of some running RX connections, we repeat
queue_delayed_work calls each 4 RX WRs, which is a waste. It's enough
to start stale task when a first passive connection is added, and
rerun it every IPOIB_CM_RX_DELAY as long as there are outstanding
passive connections.
This removes some code from RX data path.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_cq_clean() updates the CQ consumer index without moving CQEs
back to HW ownership. As a result, the same WRID might get reported
twice, resulting in a use-after-free. This was observed in IPoIB CM.
Fix by moving all freed CQEs to HW ownership.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=617>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.
Found by Ronni Zimmermann at Mellanox.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several checks in the rdma_cm check against the state of the
cm_id, but only to validate that the cm_id is bound to an underlying
transport specific CM and an RDMA device. Make the check explicit
in what we're trying to check for, since we're not synchronizing
against the cm_id state.
This will allow a user to disconnect a cm_id or reject a connection
after receiving a device removal event.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cma_iw_handler needs to validate the state of the rdma_cm_id before
processing a new connection request to ensure that a device removal is
not already being processed for the same rdma_cm_id. Without the state
check, the user can receive simultaneous callbacks for the same cm_id, or
a callback after they've destroyed the cm_id.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new routine and rename another to encapsulate common code for
synchronizing with device removal.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Scaling code is still considered experimental, so disable it by default
- Increase version to SVNEHCA_0023
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA's sysfs attributes are now being created via sysfs_create_group(),
making the process neatly table-driven. The return value is checked, thus
fixing a few compiler warnings.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- In ehca_process_eq(), we're IRQ safe throughout the whole function, so we
don't need another _irqsave in the middle of flight.
- take_over_work() is only called by comp_pool_callback(), so it can move
into the same #ifdef block.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
AQP0/1 should report qp_num={0|1} and the actual QP# should be stored
in struct ehca_qp, not the other way round.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver needs to always supply the "GRH present" flag to the
hypervisor, whether it's true or false. Not supplying it (i.e. not
setting the corresponding mask bit) amounts to a "perhaps", which we
don't want.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some pSeries hypervisor versions show a race condition in the allocate
MR hCall. Serialize this call per adapter to circumvent this problem.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Once upon a time, GPIO interrupts were rare. But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception. This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips. Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on. An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.
Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: fix PXA27x MMC workaround for bad CRC with 136 bit response
mmc: use assigned major for block device
sdhci: handle dma boundary interrupts
mmc: au1xmmc command types check from data flags
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Update defconfig.
[VIDEO]: XVR-500 and XVR-2500 need FB=y.
[SPARC32]: asm/system.h needs asm/smp.h
[SPARC32]: Update defconfig.
[SPARC32]: Fix sparc32 kdebug changes.
[SPARC64]: Accept ebus_bus_type for generic DMA ops.
[SPARC64]: Add missing cpus_empty() check in hypervisor xcall handling.
[SCSI]: Add help text for SCSI_ESP_CORE.
[SPARC] SBUS: display7seg.c needs asm/io.h
[SPARC] SBUS: bbc_i2c.c needs asm/io.h
[SPARC64]: Be more resiliant with PCI I/O space regs.
[SERIAL] SUNHV: Add an ID string.
... and make it depend on the response flag instead of the command type.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When the device hits certain memory boundaries, it signals an
interrupt and expects to be serviced. We don't need the feature
but we need to make sure the device doesn't stall.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch has changed command types check from data flags.
MMC_STOP_TRANSMISSION is never passed to au1xmmc_send_command().
SEND_STOP() is used for MMC_STOP_TRANSMISSION.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Trivial fix to follow the DECLARE_WORK changes, this makes the HD64461
touchscreen driver work properly again. As pointed out by David Howells.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
there is a wrong id in drivers/char/agp/via-agp.c
#define PCI_DEVICE_ID_VIA_CX700 0x8324
It must be 0x0324
Notice that PCI_DEVICE_ID_VIA_CX700 is also used in
drivers/i2c/busses/i2c-viapro.c and
drivers/ide/pci/via82cxxx.c
So, I think that constant must be renamed to avoid conflicting.
I attached a proposed patch.
Signed-off-by: Dave Jones <davej@redhat.com>
... doh
Jeremy Fitzhardinge noted that the recent loop.c cleanups worked, but
cause lockdep to complain.
Ouch. OK, the deadlock is real and yes, I'm an idiot. Speaking of which,
we probably want to s/lock/pin/ in drivers/base/map.c to avoid such
brainos again. And yes, this stuff needs clear documentation. Will try
to put one together once I get some sleep...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_MLX4_DEBUG works out to a def_bool y for those that have
CONFIG_EMBEDDED set. Make it depend on MLX4_CORE.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When trying to load the ipmi_si module on a powerpc with no BMC (baseboard
management controller) the driver failes to load correctly, but doesn't
unregister itself from of_platform. So, on a second modprobe the kernel
crashes. This patch adds the missing unregister call.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a rather obvious error that Patrick found in the setup routines. Need to
set the proper address space in the ACPI case.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On PPC64, we need to include asm/prom.h for function definitions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush the tty flip buffer when the line discipline input queue is flushed,
including the user call tcflush(TCIFLUSH/TCIOFLUSH). This prevents
unexpected stale data after a user application calls tcflush().
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Antonino Ingargiola <tritemio@gmail.com>
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pm3fb_setup() should only compiled if pm3fb is built statically in the kernel.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_platform: don't use generic ata_port_start
Use menuconfig objects: libata
add the ATI SB700 SATA controller device id to AHCI pci table
Add the combined mode for ATI SB700
pata_pcmcia: recognize 2GB CompactFlash from Transcend
git-libata-all: sata_via build fix
libata-acpi: clean up parameters and misc stuff
libata-acpi: s/CONFIG_SATA_ACPI/CONFIG_ATA_ACPI/
libata: give devices one last chance even if recovery failed with -EINVAL
libata: fallback to the other IDENTIFY on device error, take#2
libata: ignore EH scheduling during initialization
libata: clean up SFF init mess
libata: implement libata.spindown_compat
libata: reimplement suspend/resume support using sdev->manage_start_stop
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (35 commits)
Add support for the Davicom DM9161A PHY
sky2: only disable 88e8056 on some boards
sky2: 88e8071 support not ready
skge: crash on shutdown/suspend
sky2: fix oops on shutdown
mlx4: don't use deprecated IRQ flags
netxen_nic_main don't use deprecated irq flags
Use menuconfig objects II - netdev/wan
Use menuconfig objects II - netdev/pcmcia
Use menuconfig objects II - netdev/atm
Use menuconfig objects: netdev
Use menuconfig objects: PHY
spidernet: remove unnecessary accesses to phy
S2IO: Statistics for link up/down and memory allocated/freed
S2IO: statistics for memory allocation failuers
S2IO: getringparam ethtool option
[PATCH] libertas: 64-bit cleanups
[PATCH] libertas: sparse fixes
[PATCH] libertas: fix missing unlock in TX error path
[PATCH] libertas: make debugfs.c sparse-clean
...
Today's find is a triggered assertion in msi_free_irqs() when the system
doesn't support MSI, in which case arch_setup_msi_irqs() always returns
an error.
The problem is that when this happens we branch into msi_free_irqs(), to
which you added the following assertion loop:
list_for_each_entry(entry, &dev->msi_list, list)
BUG_ON(irq_has_action(entry->irq));
Well, if arch_setup_msi_irqs() fails, entry->irq will be zero and
although that's never assigned to any normal devices we use that IRQ
number for the timer interrupt on sparc64 so this assertion triggers.
Better to test for zero before doing the irq_has_action() assertion
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a system where I have a simple IDE controller that sits on a
local bus without bus master dma capability, and thus no dma_mapping
ops defined for the device/bus.
pata_platform works great for me, with the exception of using the generic
ata_port_start which tries to do a dmam_alloc_coherent.
Looks like it doesn't need to allocate a prd table at all, so replace it
with a dummy function instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the device ID to AHCI pci table for ATI SB700 SATA controller, the
subsequent chipset of SB600.
Signed-off-by: henry su<henry.su@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Besides those modes in ATI SB600 SATA controller, ATI SB700 supports one
more mode:the combined mode.
The combined mode is a Legacy IDE mode used for compatibility with some old
OS without AHCI driver, but now it is not necessary for Linux since the
kernel has supported AHCI.
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch cleans up libata-acpi such that it looks similar to other
libata files. This patch doesn't introuce any behavior changes.
* make libata-acpi functions take ata_device instead of ata_port +
device index
* s/atadev/dev/
* de-indent local variable declarations
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI applies to both SATA and PATA. Drop the 'S' from the config
variable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After certain errors, some devices report complete garbage on
IDENTIFY. This can cause ata_dev_read_id() to fail with -EINVAL
resulting in immediate disabling of the device. Give the device one
last chance after -EINVAL to allow recovery from such situations. As
-EINVAL is triggered very rarely, this shouldn't cause any noticeable
affect on more common error paths.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Harald Dunkel <harald.dunkel@t-online.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It seems the world isn't as frank as we thought and some devices lie
about who they are. Fallback to the other IDENTIFY if IDENTIFY is
aborted by the device. As this is the strategy used by IDE for a long
time, it shouldn't cause too much problem.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: William Thompson <wt@electro-mechanical.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata enables SCSI host during ATA host activation which happens
after IRQ handler is registered and IRQ is enabled. All ATA ports are
in frozen state when IRQ is enabled but frozen ports may raise limited
number of IRQs after being frozen - IOW, ->freeze() is not responsible
for clearing pending IRQs. During normal operation, the IRQ handler
is responsible for clearing spurious IRQs on frozen ports and it
usually doesn't require any extra code.
Unfortunately, during host initialization, the IRQ handler can end up
scheduling EH for a port whose SCSI host isn't initialized yet. This
results in OOPS in the SCSI midlayer. This is relatively short window
and scheduling EH for probing is the first thing libata does after
initialization, so ignoring EH scheduling until initialization is
complete solves the problem nicely.
This problem was spotted by Berck E. Nash in the following thread.
http://thread.gmane.org/gmane.linux.kernel/519412
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller. This never became actually
necessary and the related code always has been subtly broken one way
or the other. Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases. Exotic
cases can simply dealt within LLDs as necessary.
This patch removes port_mask handling in SFF init helpers. SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore. All information is carried via port_info. n_ports argument
is dropped and always two ports are allocated. LLD can tell SFF to
skip certain port by marking it dummy. Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.
This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic. The following changes
are made...
* ata_pci_init_native_host() and ata_init_legacy_host() both now try
to initialized whatever they can and mark failed ports dummy. They
return 0 if any port is successfully initialized.
* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
take n_ports argument. All info should be specified via port_info
array. Always two ports are allocated.
* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
* port_info handling in all LLDs are standardized - all port_info
arrays are const stack variable named ppi. Unless the second port
is different from the first, its port_info is specified as NULL
(tells libata that it's identical to the last non-NULL port_info).
* pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an
on-stack copy instead as ata_piix does.
* pata_uli: It has 4 ports instead of 2. Don't use
ata_pci_prepare_native_host(). Allocate the host explicitly and use
init helpers. It's simple enough.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that libata uses sd->manage_start_stop, libata spins down disk on
shutdown. In an attempt to compensate libata's previous shortcoming,
some distros sync and spin down disks attached via libata in their
shutdown(8). Some disks spin back up just to spin down again on
STANDBYNOW1 if the command is issued when the disk is spun down, so
this double spinning down causes problem.
This patch implements module parameter libata.spindown_compat which,
when set to one (default value), prevents libata from spinning down
disks on shutdown thus avoiding double spinning down. Note that
libata spins down disks for suspend to mem and disk, so with
libata.spindown_compat set to one, disks should be properly spun down
in all cases without modifying shutdown(8).
shutdown(8) should be fixed eventually. Some drive do spin up on
SYNCHRONZE_CACHE even when their cache is clean. Those disks
currently spin up briefly when sd tries to shutdown the device and
then the machine powers off immediately, which can't be good for the
head. We can't skip SYNCHRONIZE_CACHE during shudown as it can be
dangerous data integrity-wise.
So, this spindown_compat parameter is already scheduled for removal by
the end of the next year and here's what shutdown(8) should do.
* Check whether /sys/modules/libata/parameters/spindown_compat
exists. If it does, write 0 to it.
* For each libata harddisk {
* Check whether /sys/class/scsi_disk/h:c:i:l/manage_start_stop
exists. Iff it doesn't, synchronize cache and spin the disk
down as before.
}
The above procedure will make shutdown(8) work properly with kernels
before this change, ones with this workaround and later ones without
it.
To accelerate shutdown(8) updates, if the compat mode is in use, this
patch prints BIG FAT warning for five seconds during shutdown (the
optimal interval to annoy the user just the right amount discovered by
hours of tireless usability testing).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Distinguish between the Davicom DM9161A PHY and the DM9161E.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use DMI to add a blacklist of broken boards (so far only one).
Hopefully, the problems will be solved later, and the the whole
blacklist can disappear.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver is not ready to support 88e8071 chip.
If this chip is present, system will hang on boot.
So remove it from PCI device id's for now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If device is not fails during module startup (like unsupported chip
version) then driver would crash dereferencing a null pointer, on shutdown
or suspend/resume.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the device is fails during module startup for some reason like
unsupported chip version then the driver would crash dereferencing a
null pointer, on shutdown or suspend/resume.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/netxen/netxen_nic_main.c: In function 'netxen_nic_open':
drivers/net/netxen/netxen_nic_main.c:738: warning: 'deprecated_irq_flag' is deprecated (declared at include/linux/interrupt.h:66)
drivers/net/netxen/netxen_nic_main.c:738: warning: 'deprecated_irq_flag' is deprecated (declared at include/linux/interrupt.h:66)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Added statistics for link up/down, last link up/down.
2. Statistics for memory allocated/freed.
3. Changed level of some DBG_PRINTs.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Added code to count the number of memory failures.
2. Added watchdog_timer counter.
3. Changed debug level for some DBG_PRINTS.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A driver for the KS8695 internal UART.
Based on the 2.6.9 driver from Micrel.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (44 commits)
V4L/DVB (5571): V4l1-compat: Make VIDIOCSPICT return errors in a useful way
V4L/DVB (5624): Radio-maestro.c cleanup
V4L/DVB (5623): Dsbr100.c Replace usb_dsbr100_do_ioctl to use video_ioctl2
V4L/DVB (5622): Radio-zoltrix.c cleanup
V4L/DVB (5621): Radio-cadet.c Replace cadet_do_ioctl to use video_ioctl2
V4L/DVB (5619): Dvb-usb: fix typo
V4L/DVB (5618): Cx88: Drop the generic i2c client from cx88-vp3054-i2c
V4L/DVB (5617): V4L2: videodev, allow debugging
V4L/DVB (5614): M920x: Disable second adapter on LifeView TV Walker Twin
V4L/DVB (5613): M920x: loosen up 80-col limit
V4L/DVB (5612): M920x: rename function prefixes from m9206_foo to m920x_foo
V4L/DVB (5611): M920x: replace deb_rc with deb
V4L/DVB (5610): M920x: remove duplicated code
V4L/DVB (5609): M920x: group like functions together
V4L/DVB (5608): M920x: various whitespace cleanups
V4L/DVB (5607): M920x: Initial support for devices likely manufactured by Dposh
V4L/DVB (5606): M920x: add "c-basic-offset: 8" to help emacs to enforce tabbing
V4L/DVB (5605): M920x: Add support for LifeView TV Walker Twin
V4L/DVB (5603): V4L: Prevent queueing queued buffers.
V4L/DVB (5602): Enable DiSEqC in Starbox II (vp7021a)
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Quicklist support for IA64
[IA64] fix Kprobes reentrancy
[IA64] SN: validate smp_affinity mask on intr redirect
[IA64] drivers/char/snsc_event.c:206: warning: unused variable `p'
[IA64] mca.c:121: warning: 'cpe_poll_timer' defined but not used
[IA64] Fix - Section mismatch: reference to .init.data:mvec_name
[IA64] more warning cleanups
[IA64] Wire up epoll_pwait and utimensat
[IA64] Fix warnings resulting from type-checking in dev_dbg()
[IA64] typo s/kenrel/kernel/
I'm using a custom BIOS to configure the northbridge GART at address
0x80000000, size 2G. Linux complains:
"Aperture from northbridge cpu 0 beyond 4GB. Ignoring."
I think there's an off-by-two error in arch/x86_64/kernel/aperture.c:
AK: use correct types for i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ACPI/PM base I/O address which is the base
for the TCO registers is defined as bits [15:7]
(highest bit is 31, lowest is 0)
The code however only reads bits [14:7]. So
base_address &= 0x00007f80;
needs to be:
base_address &= 0x0000ff80;
This patch fixes this.
Signed-off-by: Ate Wijma <ajwijma@hotmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
made debugfs.c sparse-clean, found an unused function that way
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the static definition of SUPPORT_BOOT_COMMAND.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also change WEPstatus to "wep_enabled"; it's clearer and consistent with the
WPAenabled and WPA2enabled members.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove WLAN_802_11_AUTHENTICATION_MODE enum and use IW_AUTH_ALG_* instead.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove setencryptionmode private ioctl and Encryptionmode variable.
Mostly unused, and its functionality is provided by other internal members
like WEPstatus, WPAenabled, WPA2enabled, and SIOCSIWGENIE.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obsoleted by SIOCSIWAUTH's IW_AUTH_80211_AUTH_ALG option introduced
by WE-18.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Useless; it set an internal variable that was unused anyway.
A supplicant handles all 802.1x authentication, not the driver.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Start to normalize bss_descriptor with ieee80211_network so we can
eventually replace bss_descriptor more easily.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (28 commits)
[MIPS] Rework cobalt_board_id
[MIPS] Use RTC_CMOS for Cobalt
[MIPS] Use platform_device for Cobalt UART
[MIPS] Separate Alchemy processor based boards config
[MIPS] Fix build error in atomic64_cmpxchg
[MIPS] Run checksyscalls for N32 and O32 ABI
[MIPS] tlbex: use __maybe_unused
[MIPS] excite: use __maybe_unused
[MIPS] Add extern cobalt_board_id
[MIPS] Remove unused CONFIG_TOSHIBA_BOARDS
[MIPS] Rename tb0229_defconfig to tb0219_defconfig
[MIPS] Update tb0229_defconfig; add CONFIG_GPIO_TB0219.
[MIPS] Add minimum defconfig for RBHMA4200
[MIPS] SB1: Build fix.
[MIPS] Drop __devinit tag from allocate_irqno() and free_irqno()
[MIPS] clocksource: use CLOCKSOURCE_MASK() macro
[MIPS] Remove LIMITED_DMA support
[MIPS] Remove Momenco Jaguar ATX support
[MIPS] Remove Momenco Ocelot G support
[MIPS] FPU hazard handling
...
* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
USB HID: hiddev - fix race between hiddev_send_event() and hiddev_release()
HID: add hooks for getkeycode() and setkeycode() methods
HID: switch to using input_dev->dev.parent
USB HID: Logitech wheel 0x046d/0xc294 needs HID_QUIRK_NOGET quirk
USB HID: usb_buffer_free() cleanup
USB HID: report descriptor of Cypress USB barcode readers needs fixup
Bluetooth HID: HIDP - don't initialize force feedback
USB HID: update CONFIG_USB_HIDINPUT_POWERBOOK description
HID: add input mappings for non-working keys on Logitech S510 remote
Building on the previous two ecard infrastructure changes, this patch
fixes the pata_icside build errors caused by the recent libata changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards. Convert all expansion card drivers to use them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having every driver fiddle about setting its private
IRQ operations and data, provide a helper function to contain
this functionality in one place.
Arrange to remove the driver-private IRQ operations and data when
the device is removed from the driver, and remove the driver
private code to do this.
This fixes potential problems caused by drivers forgetting to
remove these hooks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
[NETFILTER]: xt_conntrack: add compat support
[NETFILTER]: iptable_raw: ignore short packets sent by SOCK_RAW sockets
[NETFILTER]: iptable_{filter,mangle}: more descriptive "happy cracking" message
[NETFILTER]: nf_nat: Clears helper private area when NATing
[NETFILTER]: ctnetlink: clear helper area and handle unchanged helper
[NETFILTER]: nf_conntrack: Removes unused destroy operation of l3proto
[NETFILTER]: nf_conntrack: Removes duplicated declarations
[NETFILTER]: nf_nat: remove unused argument of function allocating binding
[NETFILTER]: Clean up table initialization
[NET_SCHED]: Avoid requeue warning on dev_deactivate
[NET_SCHED]: Reread dev->qdisc for NETDEV_TX_OK
[NET_SCHED]: Rationalise return value of qdisc_restart
[NET]: Fix dev->qdisc race for NETDEV_TX_LOCKED case
[UDP]: Fix AF-specific references in AF-agnostic code.
[IrDA]: KingSun/DonShine USB IrDA dongle support.
[IPV6] ROUTE: Assign rt6i_idev for ip6_{prohibit,blk_hole}_entry.
[IPV6]: Do no rely on skb->dst before it is assigned.
[IPV6]: Send ICMPv6 error on scope violations.
[SCTP]: Do not include ABORT chunk header in the notification.
[SCTP]: Correctly copy addresses in sctp_copy_laddrs
...
When exporting input device bitmaps via compat_ioctl on BIG_ENDIAN
platforms evdev calculates data size incorrectly. This causes buffer
overflow if user specifies buffer smaller than maxlen.
Signed-off-by: Kenichi Nagai <kenichi3.nagai@toshiba.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During a 'resync' or similar activity, md checks if the devices in the
array are otherwise active and winds back resync activity when they are.
This test in done in is_mddev_idle, and it is somewhat fragile - it
sometimes thinks there is non-sync io when there isn't.
The test compares the total sectors of io (disk_stat_read) with the sectors
of resync io (disk->sync_io). This has problems because total sectors gets
updated when a request completes, while resync io gets updated when the
request is submitted. The time difference can cause large differenced
between the two which do not actually imply non-resync activity. The test
currently allows for some fuzz (+/- 4096) but there are some cases when it
is not enough.
The test currently looks for any (non-fuzz) difference, either positive or
negative. This clearly is not needed. Any non-sync activity will cause
the total sectors to grow faster than the sync_io count (never slower) so
we only need to look for a positive differences.
If we do this then the amount of in-flight sync io will never cause the
appearance of non-sync IO. Once enough non-sync IO to worry about starts
happening, resync will be slowed down and the measurements will thus be
more precise (as there is less in-flight) and control of resync will still
be suitably responsive.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the obsolete "if [ ]" construct from the video console Kconfig
file.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert internal wait_pm2() function to fb API fb_sync() method.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let the user enable debugging messages in nvidiafb.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a framebuffer driver to ATMEL AT91SAM9x and AT32 aka AVR32 platforms.
Those chips share quite the same IP and this code is suitable for both
architectures.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a basic port from 2.4 kernel to 2.6. Acceleration is lost and big
endian support probably too. The driver works in 8, 16 and 32 bit mode.
[adaplas]
- change VESA_* to FB_BLANK_* constants
- removed unused function clear_memory
- fix uninitialized variable compiler warning
- some whitespace cleaning
[akpm@linux-foundation.org: Nuke pestiferous CVS string]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The process_session() and process_group() values are not really used by the
driver.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: <containers@lists.osdl.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add error processing. Hanging up by an infinite loop is evaded.
Signed-off-by: kogiidena <kogiidena@eggplant.ddo.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI master driver for MPC52xx using its Programmable Serial Controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dragos Carp <dragos.carp@toptica.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add compat_ioctl method for tty code to allow processing of 32 bit ioctl
calls on 64 bit systems by tty core, tty drivers, and line disciplines.
Based on patch by Arnd Bergmann:
http://www.uwsg.iu.edu/hypermail/linux/kernel/0511.0/1732.html
[akpm@linux-foundation.org: make things static]
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This got somehow lost in the noise. This fixes coverity bug id #1025, if
Rup is greater or equal to MAX_RUP, we run past the Mapping Array.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 32 bit ioctl on 64 bit systems for synclink_gt
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This dongle does not follow the usb-irda specification, so it needs its
own special driver. In addition, it uses interrupt endpoints instead of
bulk ones as the rest of USB IrDA dongles supported by Linux (just to be
different?) and data reads need to be parsed to extract the valid bytes
before being unwrapped (details in the comment at the start of the
source). No speed commands have been discovered for this dongle, and I
suspect it does not have any at all.
On plugin, this dongle reports vendor and device IDs: 0x07c0:0x4200 .
The Windows driver that is used normally to control this dongle has a
filename of DSIR620.SYS .
Signed-off-by: Alex Villac�s Lasso <a_villacis@palosanto.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A trivial fix to (what looks like) an unintentional fall-through in the
HCI line discipline.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Normally a serial Bluetooth device is opened, TIOSETD'ed to N_HCI line
discipline, HCIUARTSETPROTO'ed and finally closed. In case the device
fails to HCIUARTSETPROTO, closing it produces a NULL pointer dereference.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Adding HCIUARTGETDEVICE makes it possible to get the HCI device number
that is attached to a given serial device. This is required during the
initialization process of some Bluetooth chips.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] MTX-1 Watchdog driver
[WATCHDOG] s3c2410_wdt - initialize watchdog irq resource
[WATCHDOG] Kconfig menuconfig patch
[WATCHDOG] pcwd.c: Port to the new device driver model
[WATCHDOG] use mutex instead of semaphore in Berkshire USB-PC Watchdog driver
[WATCHDOG] the scheduled removal of the i8xx_tco watchdog driver
[WATCHDOG] Semi-typical watchdog bug re early misc_register()
[WATCHDOG] add support for the w83627thf chipset.
drivers/input/misc/ixp4xx-beeper.c: In function 'ixp4xx_spkr_event':
drivers/input/misc/ixp4xx-beeper.c:54: error: 'input_dev' undeclared (first use in this function)
drivers/input/misc/ixp4xx-beeper.c:54: error: (Each undeclared identifier is reported only once
drivers/input/misc/ixp4xx-beeper.c:54: error: for each function it appears in.)
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (24 commits)
[POWERPC] Fix compile error with kexec and CONFIG_SMP=n
[POWERPC] Split initrd logic out of early_init_dt_scan_chosen() to fix warning
[POWERPC] Fix warning in hpte_decode(), and generalize it
[POWERPC] Minor pSeries IOMMU debug cleanup
[POWERPC] PS3: Fix sys manager build error
[POWERPC] Assorted janitorial EEH cleanups
[POWERPC] We don't define CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
[POWERPC] pmu_sys_suspended is only defined for PPC32
[POWERPC] Fix incorrect calculation of I/O window addresses
[POWERPC] celleb: Update celleb_defconfig
[POWERPC] celleb: Fix parsing of machine type hack command line option
[POWERPC] celleb: Fix PCI config space accesses to subordinate buses
[POWERPC] celleb: Fix support for multiple PCI domains
[POWERPC] Wire up sys_utimensat
[POWERPC] CPM_UART: Removed __init from cpm_uart_init_portdesc to fix warning
[POWERPC] User rheap from arch/powerpc/lib
[POWERPC] 83xx: Fix the PCI ranges in the MPC834x_MDS device tree.
[POWERPC] 83xx: Fix the PCI ranges in the MPC832x_MDS device tree.
[POWERPC] CPM_UART: cpm_uart_set_termios should take ktermios, not termios
[POWERPC] Change rheap functions to use ulongs instead of pointers
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Use alloc_pci_dev() in PCI bus probes.
[SPARC64]: Bump PROMINTR_MAX to 32.
[SPARC64]: Fix recursion in PROM tree building.
[SERIAL] sunzilog: Interrupt enable before ISR handler installed
[SPARC64] PCI: Consolidate PCI access code into pci_common.c
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acpi,msi-laptop: Fall back to EC polling mode for MSI laptop specific EC commands
sony-laptop: rename SONY_LAPTOP_OLD to a more meaningful SONYPI_COMPAT
asus-laptop: version bump and lindent
asus-laptop: fix light sens init
asus-laptop: add GPS support
asus-laptop: notify ALL events
ACPICA: Lindent
ACPI: created a dedicated workqueue for notify() execution
Revert "ACPICA: fix AML mutex re-entrancy"
Revert "Execute AML Notify() requests on stack."
Revert "ACPICA: revert "acpi_serialize" changes"
ACPI: delete un-reliable concept of cooling mode
ACPI: thermal trip points are read-only
* 'juju' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (138 commits)
firewire: Convert OHCI driver to use standard goto unwinding for error handling.
firewire: Always use parens with sizeof.
firewire: Drop single buffer request support.
firewire: Add a comment to describe why we split the sg list.
firewire: Return SCSI_MLQUEUE_HOST_BUSY for out of memory cases in queuecommand.
firewire: Handle the last few DMA mapping error cases.
firewire: Allocate scsi_host up front and allocate the sbp2_device as hostdata.
firewire: Provide module aliase for backwards compatibility.
firewire: Add to fw-core-y instead of assigning fw-core-objs in Makefile.
firewire: Break out shared IEEE1394 constant to separate header file.
firewire: Use linux/*.h instead of asm/*.h header files.
firewire: Uppercase most macro names.
firewire: Coding style cleanup: no spaces after function names.
firewire: Convert card_rwsem to a regular mutex.
firewire: Clean up comment style.
firewire: Use lib/ implementation of CRC ITU-T.
CRC ITU-T V.41
firewire: Rename fw-device-cdev.c to fw-cdev.c and move header to include/linux.
firewire: Future proof the iso ioctls by adding a handle for the iso context.
firewire: Add read/write and size annotations to IOC numbers.
...
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] update default configuration.
[S390] Kconfig: no wireless on s390.
[S390] Kconfig: use common Kconfig files for s390.
[S390] Kconfig: common config options for s390.
[S390] Kconfig: unwanted menus for s390.
[S390] Kconfig: menus with depends on HAS_IOMEM.
[S390] Kconfig: refine depends statements.
[S390] Avoid compile warning.
[S390] qdio: re-add lost perf_stats.tl_runs change in qdio_handle_pci
[S390] Avoid sparse warnings.
[S390] dasd: Fix modular build.
[S390] monreader inlining cleanup.
[S390] cio: Make some structures and a function static.
[S390] cio: Get rid of _ccw_device_get_device_number().
[S390] fix subsystem removal fallout
Lots of places where we passed a "struct pci_device *" rather than
a "struct device *". One place where we used a "%s" in the format,
but forgot to provide an argument.
Acked-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
CC drivers/i2c/busses/i2c-at91.o
drivers/i2c/busses/i2c-at91.c: In function 'at91_i2c_probe':
drivers/i2c/busses/i2c-at91.c:213: warning: implicit declaration of function 'IS_ERR'
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make i2c-at91 register as i2c adapter zero (none of these chips seem to
have more than one TWI controllers) to let it kick in any board-specific
device declarations; also make it hotplug/coldplug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a raid1 has only one working drive, we want read error to propagate up
to the filesystem as there is no point failing the last drive in an array.
Currently the code perform this check is racy. If a write and a read a
both submitted to a device on a 2-drive raid1, and the write fails followed
by the read failing, the read will see that there is only one working drive
and will pass the failure up, even though the one working drive is actually
the *other* one.
So, tighten up the locking.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for struct class_device -> struct device input core
conversion, switch to using input_dev->dev.parent when specifying device
position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From commit 7d054817b780e664bed6701b2aa637718e1905b7:
> According to the PXA27x developer's manual, we shall do so.
We shall also at least compile test our changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SCSI layer only passes sg requests down, so drop the
use_sg == 0, request_bufflen != 0 case.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
