Every tracing file must have its own TRACE_SYSTEM defined.
The mac80211 tracepoint header broke this and add in the middle
of the file had:
#undef TRACE_SYSTEM
#define TRACE_SYSTEM mac80211_msg
Unfortunately, this broke new code in the ftrace infrastructure.
Moving the mac80211_msg into its own trace file with its own
TRACE_SYSTEM defined fixes the issue.
Link: http://lkml.kernel.org/r/1428389938.1841.1.camel@sipsolutions.net
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This changes a couple of messages from sdata_info to sdata_dbg.
This should reduce some log spam, as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=1206468
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the statistical descriptor "standard deviation"
to better describe the current properties of Minstrel and
Minstrel-HTs success probability distribution. The standard
deviation (SD) is calculated as exponential weighted moving
standard deviation (EWMSD) and its current value is added as
new column in all rc_stats (in debugfs).
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch reduces the calculation costs of the EWMA macro from
"2x multiplication and 1 addition" down to "1x multiplication and
2x additions". This slightly improves performance depending on the
CPU architecture.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the new statistic "maximum possible lossless
throughput" to Minstrels and Minstrel-HTs rc_stats (in debugfs). This
enables comprehensive comparison between current per-rate throughput
and max. achievable per-rate throughput.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch moves Minstrels and Minstrel-HTs per-rate throughput
calculation (EWMA(thr)) into a dedicated function to be called.
Therefore the variable "unsigned int cur_tp" within struct
"minstrel_rate_stats" becomes obsolete. and is removed to free
up its space.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch ensures a consistent usage of variable names for type
"minstrel_rate_stats" to be used as "mrs" and from type minstrel_rate
as "mr" across both Minstrel & Minstrel-HT. In addition some
variable and function names got changed to more meaningful ones.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch unifies the calculation of Minstrels and Minstrel-HTs
per-rate statistic. The new common function minstrel_calc_rate_stats()
is called when a statistic update is performed.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a new debugfs file "rc_stats_csv" to output
Minstrel-HTs statistics in a common csv format that is easy
to parse.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
[remove printing current time of day]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a new debugfs file "rc_stats_csv" to output Minstrels
statistics in a common csv format that is easy to parse.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
[remove printing current time of day]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch restructures the rc_stats debugfs table of Minstrel-HT in
order to achieve better human readability. A new layout of the
statistics and a new header is added. In addition to the old layout
there are two new columns of information added:
idx - representing the rate index of each rate in mac80211 which
can be used to set specific rates as fixed rate via debugfs
airtime - the tx-time in micro seconds that a 1200 Byte packet
takes to be transmitted over the air at the given rate
The old layout of rc_stats:
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
HT20/LGI MCS0 5.6 100.0 100.0 1 0( 0) 1( 1)
HT20/LGI B MCS1 10.5 100.0 100.0 0 0( 0) 1( 1)
HT20/LGI A MCS2 14.8 100.0 100.0 0 0( 0) 1( 1)
...
is changed into this new layout:
best ________rate______ __statistics__ ________last_______ ______sum-of________
mode guard # rate [name idx airtime] [ ø(tp) ø(prob)] [prob.|retry|suc|att] [#success | #attempts]
HT20 LGI 1 MCS0 0 1480 0.0 0.0 0.0 1 0 0 0 0
HT20 LGI 1 B MCS1 1 740 10.5 100.0 100.0 0 0 0 1 1
HT20 LGI 1 A MCS2 2 496 14.8 100.0 100.0 0 0 0 1 1
...
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch restructures the rc_stats debugfs table of Minstrel in
order to achieve better human readability. A new layout of the
statistics and a new header is added. In addition to the old layout
there are two new columns of information added:
idx - representing the rate index of each rate in mac80211 which
can be used to set specific rates as fixed rate via debugfs
airtime - the tx-time in micro seconds that a 1200 Byte packet
takes to be transmitted over the air at the given rate
The old layout of rc_stats:
rate tpt eprob *prob ret *ok(*cum) ok( cum)
DP 1 0.9 93.5 100.0 1 0( 0) 2( 2)
2 0.4 40.0 100.0 0 0( 0) 4( 10)
5.5 0.0 0.0 0.0 0 0( 0) 0( 0)
...
is changed into this new layout:
best _______rate_____ __statistics__ ________last_______ ______sum-of________
rate [name idx tx-time] [ ø(tp) ø(prob)] [prob.|retry|suc|att] [#success | #attempts]
DP 1 0 9738 0.9 93.5 100.0 1 1 1 2 2
2 1 4922 0.4 40.0 100.0 1 0 0 4 10
5.5 2 1858 0.0 0.0 0.0 2 0 0 0 0
...
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently have a hand-rolled table with 256 entries and are
using the last byte of the MAC address as the hash. This hash
is obviously very fast, but collisions are easily created and
we waste a lot of space in the common case of just connecting
as a client to an AP where we just have a single station. The
other common case of an AP is also suboptimal due to the size
of the hash table and the ease of causing collisions.
Convert all of this to use rhashtable with jhash, which gives
us the advantage of a far better hash function (with random
perturbation to avoid hash collision attacks) and of course
that the hash table grows and shrinks dynamically with chain
length, improving both cases above.
Use a specialised hash function (using jhash, but with fixed
length) to achieve better compiler optimisation as suggested
by Sergey Ryazanov.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the upcoming fast-xmit patch, changing station state will
build a header cache based on the station's capabilities, and
as the QoS capability (sta.wme) impacts the header, it needs
to be set before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These are mandated by IEEE802.11-2012 section 8.5.8.6 and IEEE802.11ac-2013
section 8.5.8.16.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT support for IBSS. Drivers could activate
this feature by setting NL80211_EXT_FEATURE_VHT_IBSS
flag.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of wide bandwidth (wider than 20MHz) used by IBSS,
scan all channels in chandef to be able to find neighboring
IBSS netwqworks that use the same overall channels but a different
control channel.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to look up the RA station earlier to implement a TX
fastpath, factor out the lookup from ieee80211_build_hdr().
To always have a valid station pointer, also move some of the
checks into the new function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Indicating just the peer's capability is fairly pointless
if the local device doesn't support it. Make the variable
track both combined, and remove the 'local support' check
in the TX path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Louis reported that a static checker was complaining that
the 'dst' variable was set (multiple times) but not used.
This is due to a previous commit having removed the usage
(apparently erroneously), so add it back.
Fixes: a344d6778a ("mac80211: allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR")
Reported-by: Louis Langholtz <lou_langholtz@me.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is written using an anti-pattern called "success handling"
which makes it hard to read, especially if you are used to normal kernel
style. It should instead be written as a list of directives in a row
with branches for error handling.
(Basically copied from Dan's previous patch for CCM)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is written using an anti-pattern called "success handling"
which makes it hard to read, especially if you are used to normal kernel
style. It should instead be written as a list of directives in a row
with branches for error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 8ade538bf3 ("mac80111: Add BIP-GMAC-128 and BIP-GMAC-256
ciphers") had the success return in incorrect place before the
crypto_aead_setauthsize() call which practically ended up skipping that
call unconditionally.
The missing call did not actually change any functionality since
GMAC_MIC_LEN (16) is identical to the maxauthsize in gcm(aes) and as
such, the default value used for the authsize parameter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a peer or some local agent (rate control, ...) decides to start
an aggregation session but doesn't support HT (which also implies
QoS), reject it.
This is mostly a corner case as such peers normally won't try to
use block-ack sessions and rate control wouldn't start them, but
technically QoS stations could request it according to the spec.
However, since drivers don't really support such non-HT sessions
it's better to reject them.
Also, while at it, move the tracing for TX sessions earlier so it
captures the error cases as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Seems Broadcom TDLS peers (Nexus 5, Xperia Z3) refuse to allow TDLS
connection when channel-switching is supported but the regulatory
classes IE is missing from the setup request.
Add a chandef to reg-class translation function to cfg80211 and use it
to add the required IE during setup. For now add only the current
regulatory class as supported - it is enough to resolve the
compatibility issue.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop scan before authentication or association to make sure
that nothing interferes with connection flow.
Currently mac80211 defers RX auth and assoc packets (among other ones)
until after the scan is complete, so auth during scan is likely to fail
if scan took too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the reason
of the deauth.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the authentication.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate control locking caused a potential deadlock here due to the
locks being acquired in different orders, so that change cannot yet
be applied. However, there's no fundamental reason for this code to
hold the sta->lock while transmitting frames.
Clearly it's better not to hold the lock for longer periods of time,
which can happen here since we call all the way down to the driver.
Change the code a bit to not hold it while doing that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of looking up the destination station twice in the TX path
(first to build the header, and then for control processing), save
it when building the header and use it later in the TX path.
To avoid having to look up the station in the many callers, allow
those to pass %NULL which keeps the existing lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_build_hdr(), the station is looked up to build the
header correctly (QoS field) and to check for authorization. For
mesh, authorization isn't checked here, and QoS capability is
mandatory, so the station lookup can be avoided.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's no station on the 4-addr VLAN interface, then frames
cannot be transmitted. Drop such frames earlier, before setting
up all the information for them.
We should keep the old check though since that code might be used
for other internally-generated frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to look up the destination station twice while
building the 802.11 header for a given frame if the frame will
actually be transmitted to the station we initially looked up.
This happens for 4-addr VLAN interfaces and TDLS connections, which
both directly send the frame to the station they looked up, though
in the case of TDLS some station conditions need to be checked.
To avoid that, add a variable indicating that we've looked up the
station that the frame is going to be transmitted to, and avoid the
lookup/flag checking if it already has been done.
In the TDLS case, also move the authorized/wme_sta flag assignment
to the correct place, i.e. only when that station is really used.
Before this change, the new lookup should always have succeeded so
that the potentially erroneous data would be overwritten.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This mechanism was historic, and only ever used by IBSS, which
also doesn't need to have it as it properly manages station's
802.1X PAE state (or, with WEP, always has a key.)
Remove the mechanism to clean up the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a key is installed using a cipher scheme, set a new
internal key flag (KEY_FLAG_CIPHER_SCHEME) on it, to allow
distinguishing such keys more easily.
In particular, use this flag on the TX path instead of
testing the sta->cipher_scheme pointer, as the station is
NULL for broad-/multicast message, and use the key's iv_len
instead of the cipher scheme information.
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
[add missing documentation, rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put station specific code in ieee80211_update_sta_info
function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On very high MCS bitrates, the calculated duration of rates that are
next to each other can be very imprecise, due to the small packet size
used as reference (1200 bytes).
This is most visible in VHT80 nss=2 MCS8/9, for which minstrel shows the
same throughput when the probability is also the same. This leads to a
bad rate selection for such rates.
Fix this issue by introducing an average A-MPDU size factor into the
calculation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently when TDLS station in driver goes from authenticated
to associated state it can not use rate control parameters
because rate control is not initialized yet. Some drivers
require parameters already initialized by rate control when
entering associated state. It can be done by initializing
rate control after station transition to associated state but
before notifying driver about that.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
[fix comment to say 'associated' instead of 'authorized']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP is confused and starts doing a CSA to the same channel,
just ignore that request instead of trying to act it out since it
was likely sent in error anyway.
In the case of the bug I was investigating the GO was misbehaving
and sending out a beacon with CSA IEs still included after having
actually done the channel switch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a beacon from the AP contains only the ECSA IE, and not a CSA IE
as well, this ECSA IE is not considered for calculating the CRC and
the beacon might be dropped as not being interesting. This is clearly
wrong, it should be handled and the channel switch should be executed.
Fix this by including the ECSA IE ID in the bitmap of interesting IEs.
Reported-by: Gil Tribush <gil.tribush@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since moving the interface combination checks to mac80211, it's
broken because it now only considers interfaces with an assigned
channel context, so for example any interface that isn't active
can still be up, which is clearly an issue; also, in particular
P2P-Device wdevs are an issue since they never have a chanctx.
Fix this by counting running interfaces instead the ones with a
channel context assigned.
Cc: stable@vger.kernel.org [3.16+]
Fixes: 73de86a389 ("cfg80211/mac80211: move interface counting for combination check to mac80211")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[rewrite commit message, dig out the commit it fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The schedule_work()/mutex unlocking code is duplicated many times,
refactor that to a common place in the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow mac80211 drivers to call cfg80211 APIs with
the right handle.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the netdev stats accounting into the common function
ieee80211_deliver_skb() that is called in both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
timeout was being passed as int but assigned from u32/u16 values and used
as unsigned type. This is really only for better readability.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is primarily an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var) which also handles
corner cases correctly.
There is a change of behavior as e.g. for HZ 100, t * HZ / 1000 will
return 0 for t < 10 but msecs_to_jiffies will return at least 1 always.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some device drivers offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
[fix commit log, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes the driver might want to modify private data in interfaces
that are down. One possible use-case is cleaning up interface state
after HW recovery. Some interfaces that were up before the recovery took
place might be down now, but they might still be "dirty".
Introduce a new iterate_interfaces() API and a new ACTIVE iterator flag.
This way the internal implementation of the both active and inactive
APIs remains the same.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_tx_prepare_skb() function currently entirely ignores
the fact that the SKB that is passed in might be split into more
than one due to fragmentation and doesn't check the list of skbs
that the TX handlers may create. In case this happens, it would
leak them.
Fix this and also don't leave the skb next/prev pointers dangling
pointing to the on-stack sk_buff_head.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_queue_work() we check if we're quiescing or suspended, so
it's not necessary to check for quiescing before calling this
function. Remove duplicate checks.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TDLS off-channel can be allowed in channels marked with GO_CONCURRENT,
provided the device is connected to an AP on the same UNII.
When relaxing the NO-IR requirements for TDLS, we might hit flows in
cfg80211_reg_can_beacon that acquire the wdev lock. Take some measures
to allow this during TDLS setup.
Acquire the RCU read lock later in the flow that invokes
cfg80211_reg_can_beacon.
Avoid taking local->mtx when preparing the setup packet to avoid
circular deadlocks with mac80211 code that is invoked with wdev-mtx
held.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver rejects WoWLAN, restart the queues before returning
to cfg80211. cfg80211 will return to mac80211, but not before it
disconnects all interfaces. If we don't start the queues, any of
the packets needed for disconnecting won't be transmitted, which
is strange. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We check local->open_count at the top of the __ieee80211_suspend(), so
there's no need to check for it again. open_count is protected by the
rtnl, so there's no chance for it to have change between the two
calls.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers can't really be expected to suspend properly while auth
or assoc is in progress since then they don't have any state
they could keep with WoWLAN, nor can they actually finish the
authentication or association. In fact, keeping this can cause
subtle issues with drivers like iwlwifi that refuse WoWLAN if
not associated, but have trouble figuring out what's going on
in the middle of association.
In any case, regardless of possible driver issues in this area,
it doesn't make sense for mac80211 to try to WoWLAN-suspend in
the middle of such operations, so stop them before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
If any interface fails to be added to the driver in during reconfig,
we should remove all the successfully added interfaces and report
reconfig failure, so things can be cleaned up properly. Failing to do
so can lead to subsequent failures and leave the drivers in a messed
up state.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 disconnects, but has no insight into the association
process, it can happen that it disconnects while association is in
progress. We then try to abort association in mac80211, but this is
only later so the association can complete between the two.
This results in removing an interface from the driver while bound
to the channel context, obviously causing confusion and issues.
Solve this by also checking if we're associated during quiesce and
if so deauthenticating. The frame will no longer go out to the AP
which is a bit unfortunate, but it'll resolve the crash (and before
we would have suspended without telling the AP as well.)
I'm working on a better, but more complex solution as well, which
should avoid that problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the AID and VHT-cap/operation IEs during TDLS setup. Remove the
block of TDLS peers when setting HT-caps of the peer station.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon's timestamp, device system time associated with this beacon and
DTIM count parameters are not updated in the associated vif context
if the latest beacon's content is identical to the previously received.
It make sense to update these changing parameters on every beacon so the
driver can get most updated values. This may be necessary, for example,
to avoid either beacons' drift effect or device time stamp overrun.
IMPORTANT: Three sync_* parameters - sync_ts, sync_device_ts and
sync_dtim_count would possibly be out of sync by the time the driver will
use them. The synchronized view is currently guaranteed only in certain
callbacks.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".
In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)
The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some APs experience problems when working with
U-APSD. Decreasing the probability of that
happening by using legacy mode for all ACs but VO
isn't enough.
Cisco 4410N originally forced us to enable VO by
default only because it treated non-VO ACs as
legacy.
However some APs (notably Netgear R7000) silently
reclassify packets to different ACs. Since u-APSD
ACs require trigger frames for frame retrieval
clients would never see some frames (e.g. ARP
responses) or would fetch them accidentally after
a long time.
It makes little sense to enable u-APSD queues by
default because it needs userspace applications to
be aware of it to actually take advantage of the
possible additional powersavings. Implicitly
depending on driver autotrigger frame support
doesn't make much sense.
Cc: stable@vger.kernel.org
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh forwarding path was not checking that data
frames were protected when running an encrypted network;
add the necessary check.
Cc: stable@vger.kernel.org
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit ad38bfc916 ("mac80211: Tx frame latency statistics")
(along with some follow-up fixes).
This code turned out not to be as useful in the current form as we
thought, and we've internally hacked it up more, but that's not
very suitable for upstream (for now), and we might just do that
with tracing instead.
Therefore, for now at least, remove this code. We might also need
to use the skb->tstamp field for the TCP performance issue, which
is more important than the debugging.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both wpa_supplicant and mac80211 have and inactivity timer. By default
wpa_supplicant will be timed out in 5 minutes and mac80211's it is 30
minutes. If wpa_supplicant uses a longer timer than mac80211, it will
get unexpected disconnection by mac80211.
Using 0xffffffff instead as the configured value could solve this w/o
changing the code, but due to integer overflow in the expression used
this doesn't work. The expression is:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On 32bit system, the right side would overflow and be a very small
value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large,
causing unexpectedly early disconnections.
Instead allow disabling the inactivity timer to avoid this situation,
by passing the (previously invalid and useless) value 0.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword/rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing AP SMPS, we need to look up all the stations
for this interface, so there's no reason to iterate over
hash chains rather than doing the simpler iteration over
the station list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since multicast addresses don't exist as stations, don't attempt
to look them up in the hashtable on TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.
EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.
In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.
The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.
It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.
Cc: stable@vger.kernel.org
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 06d961a8e2 ("mac80211/minstrel: use the new rate control API")
inverted the condition 'if (msr->sample_limit != 0)' to
'if (!msr->sample_limit != 0)'. But it is confusing both to people and
compilers (gcc5):
net/mac80211/rc80211_minstrel.c: In function 'minstrel_get_rate':
net/mac80211/rc80211_minstrel.c:376:26: warning: logical not is only applied to the left hand side of comparison
if (!msr->sample_limit != 0)
^
Let there be only 'if (!msr->sample_limit)'.
Fixes: 06d961a8e2 ("mac80211/minstrel: use the new rate control API")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If ieee80211_vif_use_channel() fails, we have to clear
sdata->radar_required (which we might have just set).
Failing to do it results in stale radar_required field
which prevents starting new scan requests.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Eliad Peller <eliad@wizery.com>
[use false instead of 0]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows mac80211 to configure BIP-GMAC-128 and BIP-GMAC-256 to the
driver and also use software-implementation within mac80211 when the
driver does not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure BIP-CMAC-256 to the driver and also
use software-implementation within mac80211 when the driver does not
support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure CCMP-256 to the driver and also use
software-implementation within mac80211 when the driver does not support
this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[squash ccmp256 -> mic_len argument change]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure GCMP and GCMP-256 to the driver and
also use software-implementation within mac80211 when the driver does
not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[remove a spurious newline]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If suspend starts while ieee80211_scan_completed() is running, between
the point where SCAN_COMPLETED is set and the work is queued,
ieee80211_scan_cancel() will not catch the work and we may finish
suspending before the work is actually executed, leaving the scan
running while suspended.
To fix this race, queue the scan work during resume if the
SCAN_COMPLETED flag is set and flush it immediately.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers without beacon filtering, support beacon statistics
entirely, i.e. report the number of beacons and average signal.
For drivers with beacon filtering, give them the number of beacons
received by mac80211 -- in case the device reports only the number
of filtered beacons then driver doesn't have to count all beacons
again as mac80211 already does.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the case of non-QoS association, the counter was actually
wrong. The right index isn't security_idx but seqno_idx, as
security_idx will be 0 for data frames, while 16 is needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These conditions are rather difficult to follow, for example
because "!sta" only exists to not crash in the case that we
don't have a station pointer (WLAN_TDLS_SETUP_REQUEST) in
which the additional condition (peer supports HT) doesn't
actually matter anyway.
Cleaning this up only duplicates two lines of code but makes
the rest far easier to read, so do that.
As a side effect, smatch stops complaining about the lack of
a sta pointer test after the !sta (since the !sta goes away)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to use another local 'sta' variable as the
original (outer scope) one isn't needed any more and has
become invalid anyway when exiting the RCU read section.
Remove the inner scope one and along with it the useless NULL
initialization.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 2ae70efcea.
The new peer events that are generated by the change are causing problems
with wpa_supplicant in userspace: wpa_s tries to restart SAE authentication
with the peer when receiving the event, even though authentication may be in
progress already, and it gets very confused.
Revert back to the original operating mode, which is to only get events when
there is no corresponding station entry.
Cc: Nishikawa, Kenzoh <Kenzoh.Nishikawa@jp.sony.com>
Cc: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that a deferred scan is queued after the queues are
flushed in __ieee80211_suspend(). The deferred scan work may be
scheduled by ROC or ieee80211_stop_poll().
To make sure don't start a new scan while suspending, check whether
we're quiescing or suspended and complete the scan immediately if
that's the case.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we go to suspend, there is complex set of states that
avoids races. The quiescing variable is set whlie
__ieee80211_suspend is running. Then suspended is set.
The code makes sure there is no window without any of these
flags.
The problem is that workers can still be enqueued while we
are quiescing. This leads to situations where the driver is
already suspending and other flows like disassociation are
handled by a worker.
To fix this, we need to check quiescing and suspended flags
in the worker itself and not only before enqueueing it.
I also add here extensive documentation to ease the
understanding of these complex issues.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 disconnects, it drops all the packets on the
queues. This happens after the net stack has been notified
that we have no link anymore (netif_carrier_off).
netif_carrier_off ensures that no new packets are sent to
xmit() callback, but we might have older packets in the
middle of the Tx path. These packets will land in the
driver's queues after the latter have been flushed.
Synchronize_net() between netif_carrier_off and drv_flush()
will fix this.
Note that we can't call synchronize_net inside
ieee80211_flush_queues since there are flows that call
ieee80211_flush_queues and don't need synchronize_net()
which is an expensive operation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[reword comment to be more accurate]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix a regression introduced by commit a5e70697d0 ("mac80211: add radiotap flag
and handling for 5/10 MHz") where the IEEE80211_CHAN_CCK channel type flag was
incorrectly replaced by the IEEE80211_CHAN_OFDM flag. This commit fixes that by
using the CCK flag again.
Cc: stable@vger.kernel.org
Fixes: a5e70697d0 ("mac80211: add radiotap flag and handling for 5/10 MHz")
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In normal cases (i.e. when we are fully associated), cfg80211 takes
care of removing all the stations before calling suspend in mac80211.
But in the corner case when we suspend during authentication or
association, mac80211 needs to roll back the station states. But we
shouldn't roll back the station states in the suspend function,
because this is taken care of in other parts of the code, except for
WDS interfaces. For AP types of interfaces, cfg80211 takes care of
disconnecting all stations before calling the driver's suspend code.
For station interfaces, this is done in the quiesce code.
For WDS interfaces we still need to do it here, so move the code into
a new switch case for WDS.
Cc: stable@kernel.org [3.15+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Control per packet Transmit Power Control (TPC) in lower drivers
according to TX power settings configured by the user. In particular TPC is
enabled if value passed in enum nl80211_tx_power_setting is
NL80211_TX_POWER_LIMITED (allow using less than specified from userspace),
whereas TPC is disabled if nl80211_tx_power_setting is set to
NL80211_TX_POWER_FIXED (use value configured from userspace)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers unfortunately cannot support software crypto, but
mac80211 currently assumes that they do.
This has the issue that if the hardware enabling fails for some
reason, the software fallback is used, which won't work. This
clearly isn't desirable, the error should be reported and the
key setting refused.
Support this in mac80211 by allowing drivers to set a new HW
flag IEEE80211_HW_SW_CRYPTO_CONTROL, in which case mac80211 will
only allow software fallback if the set_key() method returns 1.
The driver will also need to advertise supported cipher suites
so that mac80211 doesn't advertise any (future) software ciphers
that the driver can't actually do.
While at it, to make it easier to support this, refactor the
ieee80211_init_cipher_suites() code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Station info state is started in allocation, so should be
destroyed on free (it's just a timer); rate control must
be freed if anything afterwards fails to initialize.
LED exit should be later, no need for locking there, but
it needs to be done also when rate init failed.
Also clean up the code by moving a label so the locking
doesn't have to be done separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While suspending, we destroy the authentication /
association that might be taking place. While doing so, we
forgot to delete the timer which can be firing after
local->suspended is already set, producing the warning below.
Fix that by deleting the timer.
[66722.825487] WARNING: CPU: 2 PID: 5612 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]()
[66722.825487] queueing ieee80211 work while going to suspend
[66722.825529] CPU: 2 PID: 5612 Comm: kworker/u16:69 Tainted: G W O 3.16.1+ #24
[66722.825537] Workqueue: events_unbound async_run_entry_fn
[66722.825545] Call Trace:
[66722.825552] <IRQ> [<ffffffff817edbb2>] dump_stack+0x4d/0x66
[66722.825556] [<ffffffff81075cad>] warn_slowpath_common+0x7d/0xa0
[66722.825572] [<ffffffffa06b5b90>] ? ieee80211_sta_bcn_mon_timer+0x50/0x50 [mac80211]
[66722.825573] [<ffffffff81075d1c>] warn_slowpath_fmt+0x4c/0x50
[66722.825586] [<ffffffffa06977a2>] ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]
[66722.825598] [<ffffffffa06977d5>] ieee80211_queue_work+0x25/0x50 [mac80211]
[66722.825611] [<ffffffffa06b5bac>] ieee80211_sta_timer+0x1c/0x20 [mac80211]
[66722.825614] [<ffffffff8108655a>] call_timer_fn+0x8a/0x300
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.
Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.
While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.
In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are treated the same as 160 MHz in the spec,
so it makes no sense to distinguish them. As no driver
uses them yet, this is also not a problem, just remove
them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Radar detection can last indefinite time. There is no
point in deferring a scan request in this case - simply
return -EBUSY.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ctx->conf.radar_enabled should reflect whether radar
detection is enabled for the channel context.
When calculating it, make it consider only the vifs
that have this context assigned (instead of all the
vifs).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
local->radar_detect_enabled should tell whether
radar_detect is enabled on any interface belonging
to local.
However, it's not getting updated correctly
in many cases (actually, when testing with hwsim
it's never been set, even when the dfs master
is beaconing).
Instead of handling all the corner cases
(e.g. channel switch), simply check whether
radar detection is enabled only when needed,
instead of caching the result.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function adding the supported channels IE during a TDLS connection had
several issues:
1. If the entire subband is usable, the function exitted the loop without
adding it
2. The function only checked chandef_usable, ignoring flags like RADAR
which would prevent TDLS off-channel communcation.
3. HT20 was explicitly required in the chandef, while not a requirement
for TDLS off-channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When roaming / suspending, it makes no sense to wait until
the transmit queues of the device are empty. In extreme
condition they can be starved (VO saturating the air), but
even in regular cases, it is pointless to delay the roaming
because the low level driver is trying to send packets to
an AP which is far away. We'd rather drop these packets and
let TCP retransmit if needed. This will allow to speed up
the roaming.
For suspend, the explanation is even more trivial.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station disconnects with frames still pending, we clear
the TIM bit, but too late - it's only cleared when the station
is already removed from the driver, and thus the driver can get
confused (and hwsim will loudly complain.)
Fix this by clearing the TIM bit earlier, when the station has
been unlinked but not removed from the driver yet. To do this,
refactor the TIM recalculation to in that case ignore traffic
and simply assume no pending traffic - this is correct for the
disconnected station even though the frames haven't been freed
yet at that point.
This patch isn't needed for current drivers though as they don't
check the station argument to the set_tim() operation and thus
don't really run into the possible confusion.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the new counters cfg80211 can now advertise to userspace.
The TX code is in the sequence number handler, which is a bit odd,
but that place already knows the TID and frame type, so it was
easiest and least impact there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
* remove STATION_INFO_ASSOC_REQ_IES complete, but the length
(assoc_req_ies_len) can be used instead
* add NL80211_STA_INFO_RX_DROP_MISC which exists internally
but not in nl80211 yet
This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.
Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.
This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the new cfg80211_del_sta_sinfo() function to send the
statistics about the deleted station with the delete event.
This lets userspace see how much traffic etc. the deleted
station used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All of the survey data is (currently) per channel anyway,
so having the word "channel" in the name does nothing. In
the next patch I'll introduce global data to the survey,
where the word "channel" is actually confusing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
only require headroom space. Therefore, the tailroom-needed counter can
safely be decremented for most drivers.
The older incarnation of this patch (ca34e3b5) assumed that the above
holds true for all drivers. As reported by Christopher Chavez and
researched by Christian Lamparter and Larry Finger, this isn't a valid
assumption for p54 and cw1200.
Drivers that still require tailroom for ICV/MIC even when HW encryption
is enabled can use IEEE80211_KEY_FLAG_RESERVE_TAILROOM to indicate it.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Cc: Christopher Chavez <chrischavez@gmx.us>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211.git to get some changes that would otherwise
cause conflicts with new changes coming here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return value should be initialized to false so that there's a
valid return value when there are no sessions that need work to be
done on them. Luckily, the side effect of using the uninitialized
value is an extra harmless driver call.
Coverity: CID 1260096
Fixes: 02219b3abc ("mac80211: add WMM admission control support")
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[extend commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "40a11ca mac80211: check if channels allow 80 MHz for VHT
probe requests" considered disabled channels as VHT enabled, and
mistakenly sent out probe-requests with the VHT IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit ca34e3b5c8.
It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.
Cc: stable@vger.kernel.org
Fixes: ca34e3b5c8 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: Christopher Chavez <chrischavez@gmx.us>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Debugged-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
dot11MulticastTransmittedFrameCount should be updated according
to the DA, which might be different from A1. Checking A1 results
in the counter being 0 in case of station, as to-DS data frames
use A1 for the BSSID.
This behaviour is defined in state machines, specifically in the
sta_tx_dcf_3.1d(10) description of 802.11-2012.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On minstrel_ht, the size of the per-sta struct is almost 18k, making it
an order-3 allocation.
A few fields inside the per-rate statistics are bigger than they need to
be. This patch reduces the size enough to cut down the per-sta struct to
about 13k (order-2 allocation).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are no interfaces up, there is no reason
to continue the reconfig flow.
The current code might end up calling driver
callbacks (e.g. resume(), reconfig_complete())
while the driver is already stopped.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ht_oper variable is assigned a value, but never used in
ieee80211_parse_ch_switch_ie(). Remove it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit e1a0c6b ("mac80211: stop toggling IEEE80211_HT_CAP_SUP_WIDTH_20_40")
mistakenly removed the actual update of sta->sta.bandwidth.
Refactor ieee80211_sta_cur_vht_bw() into multiple functions
(calculate caps-bw and chandef-bw separately, and min them
with cur_max_bandwidth).
On ht chanwidth action frame set only cur_max_bandwidth
(according to the sta capabilities) and recalc the sta bw.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In beacons, handle the Country IE even if no Power Constraint IE
is present, and, capability wise, also in case that the Radio
Measurements capability is enabled.
In cases where the Country IE should be handled and that the
Power Constraint IE is not present, the Country IE alone will
set the power limit (and not both Country and Power Constraint
IEs).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT override configurations was ignored when choosing the channel
(until now, the override configuration affected only the
capabilities shown in the IEs).
The override configurations received only on association time,
so in this case we should determine the channel again.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When writing the code to allow per-station GTKs, I neglected to
take into account the management frame keys (index 4 and 5) when
freeing the station and only added code to free the first four
data frame keys.
Fix this by iterating the array of keys over the right length.
Cc: stable@vger.kernel.org
Fixes: e31b82136d ("cfg80211/mac80211: allow per-station GTKs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of sending peer candidate events just once, send them as long
as the peer remains in the LISTEN state in the peering state machine,
when userspace is implementing the peering manager.
Userspace may silence the events from a peer by progressing the state
machine or by setting the link state to BLOCKED.
Fixes the problem that a mesh peering process won't be fired again after
the previous first peering trial fails due to like air propagation error
if the peering is managed by user space such as wpa_supplicant.
This patch works with another patch for wpa_supplicant described here
which fires a peering process again triggered by the notice from kernel.
http://lists.shmoo.com/pipermail/hostap/2014-November/031235.html
Signed-off-by: Kenzoh Nishikawa <Kenzoh.Nishikawa@jp.sony.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to cfg80211_ch_switch_notify() should be at the end of the
ieee80211_chswitch_post_beacon() function, because it should only be
sent if everything succeeded.
Fixes: d04b5ac9e7 ("cfg80211/mac80211: allow any interface to send channel switch notifications")
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using IBSS in HT mode, we always get NSS=1
in rc_update callback. Force NSS recalculation when
rates updated and notify driver that NSS changed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The power level might have been set, but as the interface was idle
it might not have taken effect yet. Ask the driver to check the
power level when starting up an AP so that in this case the correct
power level is used in case the device/driver can only set it when
the interface is actually active.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since multicast frames are marked as no-ack, using
IEEE80211_TX_STAT_ACK to check if they have been
successfully transmitted by the driver is incorrect
since a driver can choose to ignore transmission status
for no-ack frames. This results in incorrect accounting
for such frames.
To fix this issue, this patch introduces a new flag
that can be used by drivers to indicate error-free
transmission of no-ack frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[add a note about not setting the flag for non-no-ack frames]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move IEEE80211_TX_CTL_PS_RESPONSE to info->control.flags since
this is used only in the TX path (by ath9k). This frees up
a bit which can be used for other purposes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the channel switch has been made, a vif is now using
the channel context which was reserved. When that happens,
we need to update the channel context since its parameters
may change.
I hit a case in which I switched to a 40Mhz channel but the
reserved channel context was still on 20Mhz. The rate control
would try to send 40Mhz packets on a 20Mhz channel context and
that made iwlwifi's firmware unhappy.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As multicast-frames can't be fragmented, "dot11MulticastReceivedFrameCount"
stopped being incremented after the use-after-free fix. Furthermore, the
RX-LED will be triggered by every multicast frame (which wouldn't happen
before) which wouldn't allow the LED to rest at all.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=89431 which also had the
patch.
Cc: stable@vger.kernel.org
Fixes: b8fff407a1 ("mac80211: fix use-after-free in defragmentation")
Signed-off-by: Andreas Müller <goo@stapelspeicher.org>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid a case where we would access uninitialized stack data if the AP
advertises HT support without 40MHz channel support.
Cc: stable@vger.kernel.org
Fixes: f3000e1b43 ("mac80211: fix broken use of VHT/20Mhz with some APs")
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg <johannes@sipsolutions.net> says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used by drivers that cannot reliably map tx status
information onto specific skbs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This op works like .tx_status, except it does not need access to the
skb. This will be used by drivers that cannot match tx status
information to specific packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a crash on attempting to calculate the frame duration for a VHT
packet (which needs to be handled by hw/driver instead).
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of keeping track of all those special cases where
VLAN interfaces have no bss_conf.chandef, just make sure
they have the same as the AP interface they belong to.
Among others, this fixes a crash getting a VLAN's channel
from userspace since a NULL channel is returned as a good
result (return value 0) for VLANs since the commit below.
Cc: stable@vger.kernel.org [3.18 only]
Fixes: c12bc4885f ("mac80211: return the vif's chandef in ieee80211_cfg_get_channel()")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are no channels allowing 80 MHz to be used, then the
station isn't really VHT capable even if the driver and device
support it in general. In this case, exclude the VHT capability
IE from probe request frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The supported bandwidth field is a two-bit field, not a bitmap,
so treat it accordingly when disabling 80+80 or 160 MHz.
Note that we can only advertise "80+80 and 160" or "160", not
"80+80" by itself, so disabling 160 also disables 80+80.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people
-----BEGIN PGP SIGNATURE-----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=q4e6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the queue mapping earlier, skb->queue_mapping is more likely than
skb->data to still be in d-cache.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate mask code currently assumes that a rate is legacy if
IEEE80211_TX_RC_MCS is not set. This might be the cause of bogus VHT
rates being reported with minstrel_ht.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When 20MHz chandef is used, 40MHz rates shouldn't be
used (by the rate-control algorithm), even if the sta
ht capabilities indicate support for it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Singed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to use the scan and scheduled scan request pointers during
RX to check for randomisation, make them accessible using RCU.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
local->scan_req was tested in the previous line, so it
can't be NULL.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In TDLS (e.g., TDLS off-channel) there is a requirement for
some drivers to supply an unused TID between the AP and the
device to the FW, to allow sending PTI requests and to allow
the FW to aggregate on a specific TID for better throughput.
To ensure that the allocated TID is indeed unused, this patch
introduces an API for blocking the driver from TXing on that
TID.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the HW supports IEEE80211_HW_QUEUE_CONTROL, allow
flushing only specific queues rather than all of them.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.
Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These are used in TDLS channel switching code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the data-generating from the Tx-sending functionality, as we do
not want to send templates to the lower driver. Also add an optional
chandef argument to the data-generating portion. It will be used for
channel-switch templates.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The AP or peer can prohibit TDLS channel switch via a bit in the
extended capabilities IE. Parse the IE and track this bit. Set an
appropriate STA flag if both the AP and peer STA support TDLS
channel-switching.
Add the new STA flag and the missing TDLS_INITIATOR to debugfs.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define some related TDLS protocol constants and advertise channel switch
support in the extended-capabilities IE when the feature bit is defined.
Actually supporting TDLS channel-switching also requires support for
some new nl80211 commands, to be introduced by future patches.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the BSS coex IE in case we support HT40 channels, as mandated by
section 8.5.13 in IEEE802.11 2012.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This information element is mandatory in case TDLS channel-switching is to
be supported. The channels given are ones supported and allowed to be
active in the current regulatory setting.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For some TDLS channel switch implementations data frames need to be
sent by the firmware based on a template. This template should be
created by mac80211, and thus needs to properly be built from an
802.3 frame into an 802.11 frame. In addition, the device will need
the key information so the select_key handler needs to be run.
However, the driver/device will be responsible for all of the crypto
encapsulation, as the sequence numbers etc. cannot be built by the
host anyway in this case since it's a template to be used multiple
times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out the 802.11 header building code from the xmit function
to be able to use it separately in a later commit.
While at it, fix up some documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing the band as a parameter to ieee80211_xmit()
and ieee80211_tx(), move it outside of the two functions while
making sure info->band is set up before calling them.
This removes the parameter and simplifies the follow commit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the TDLS peer station might not receive the teardown
packet (e.g., when in PS), this makes sure the packet is
retransmitted - this time through the AP - if the TDLS peer
didn't ACK the packet.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allows setting of an skb's flags - if needed - when calling
ieee80211_subif_start_xmit().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit 5935839ad7
"mac80211: improve minstrel_ht rate sorting by throughput & probability"
introduced a crash on rate sorting that occurs when the rate added to
the sorting array is faster than all the previous rates. Due to an
off-by-one error, it reads the rate index from tp_list[-1], which
contains uninitialized stack garbage, and then uses the resulting index
for accessing the group rate stats, leading to a crash if the garbage
value is big enough.
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put duplicate detection into its own RX handler, and separate
out the conditions a bit to make the code more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-vif channel switches, we want to send
NL80211_CMD_CH_SWITCH_NOTIFY to the userspace to let it decide whether
other interfaces need to be moved as well. This is needed when we
want a P2P GO interface to follow the channel of a station, for
example.
Modify the code so that all interfaces can send CSA notifications.
Additionally, send notifications for STA CSA as well.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send a channel switch notification to userspace when a channel switch
is requested or when we react to a remote CSA.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The device_timestamp value was left out of the event trace for
drv_pre_channel_switch by mistake. Add it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a mistake when merging commit 6d027bcc (mac80211: add
pre_channel_switch driver operation) for upstream. The assignment of
the values in the ch_switch structure came below the call to
drv_pre_channel_switch. Fix the order.
Fixes: 6d027bcc (mac80211: add pre_channel_switch driver operation)
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7ec7c4a9a6 (mac80211: port CCMP to
cryptoapi's CCM driver) introduced a regression when decrypting empty
packets (data_len == 0). This will lead to backtraces like:
(scatterwalk_start) from [<c01312f4>] (scatterwalk_map_and_copy+0x2c/0xa8)
(scatterwalk_map_and_copy) from [<c013a5a0>] (crypto_ccm_decrypt+0x7c/0x25c)
(crypto_ccm_decrypt) from [<c032886c>] (ieee80211_aes_ccm_decrypt+0x160/0x170)
(ieee80211_aes_ccm_decrypt) from [<c031c628>] (ieee80211_crypto_ccmp_decrypt+0x1ac/0x238)
(ieee80211_crypto_ccmp_decrypt) from [<c032ef28>] (ieee80211_rx_handlers+0x870/0x1d24)
(ieee80211_rx_handlers) from [<c0330c7c>] (ieee80211_prepare_and_rx_handle+0x8a0/0x91c)
(ieee80211_prepare_and_rx_handle) from [<c0331260>] (ieee80211_rx+0x568/0x730)
(ieee80211_rx) from [<c01d3054>] (__carl9170_rx+0x94c/0xa20)
(__carl9170_rx) from [<c01d3324>] (carl9170_rx_stream+0x1fc/0x320)
(carl9170_rx_stream) from [<c01cbccc>] (carl9170_usb_tasklet+0x80/0xc8)
(carl9170_usb_tasklet) from [<c00199dc>] (tasklet_hi_action+0x88/0xcc)
(tasklet_hi_action) from [<c00193c8>] (__do_softirq+0xcc/0x200)
(__do_softirq) from [<c0019734>] (irq_exit+0x80/0xe0)
(irq_exit) from [<c0009c10>] (handle_IRQ+0x64/0x80)
(handle_IRQ) from [<c000c3a0>] (__irq_svc+0x40/0x4c)
(__irq_svc) from [<c0009d44>] (arch_cpu_idle+0x2c/0x34)
Such packets can appear for example when using the carl9170 wireless driver
because hardware sometimes generates garbage when the internal FIFO overruns.
This patch adds an additional length check.
Cc: stable@vger.kernel.org
Fixes: 7ec7c4a9a6 ("mac80211: port CCMP to cryptoapi's CCM driver")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Deliver up to 128 frames during service period instead of 8 if
unlimited is specified by the client during association.
8 was just an arbitrary value; so is 128 since unlimited can
be any number.
However for large traffic bursts, increasing this value looks
reasonable. Also, it seems that a few certification tests
expect more frames to be delivered during SP.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the RIC data element (RDE) is included in the IEs coming
from userspace for an association request, its handling is
currently broken as any IEs that are contained within it would
be split off from it and inserted again after all the IEs that
mac80211 generates (e.g. HT, VHT.)
To fix this, treat the RIC element specially, and stop after
it only when we find something that doesn't actually belong to
it. This assumes userspace is actually correctly building it,
directly after the fast BSS transition IE and before all the
others like extended capabilities.
This leaves as a potential problem the case where userspace is
building the following IEs:
[RDE] [vendor resource description] [vendor non-resource IE]
In this case, we'd erroneously consider all three IEs to be
part of the RIC data together, and not split them between the
two vendor IEs. Unfortunately, it isn't easily possible to
distinguish vendor IEs, so this isn't easy to fix. Luckily,
this case is rare as normally wpa_supplicant will include an
extended capabilities IE in the IEs, and that certainly will
break the two vendor IEs apart correctly.
Reviewed-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds 802.11p OCB (Outside the Context of a BSS) mode
support.
When communicating in OCB mode a mandatory wildcard BSSID
(48 '1' bits) is used.
The EDCA parameters handling function was changed to support
802.11p specific values.
The insertion of a newly discovered STAs is done in the similar way
as in the IBSS mode -- through the deferred insertion.
The OCB mode uses a periodic 'housekeeping task' for expiration of
disconnected STAs (in the similar manner as in the MESH mode).
New Kconfig option for verbose OCB debugging outputs is added.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.
Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.
Cc: stable@vger.kernel.org
Reported-by: Yosef Khyal <yosefx.khyal@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use codespell to find spelling errors.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface is deleted, an ongoing hardware scan is canceled and
the driver must abort the scan, at the very least reporting completion
while the interface is removed.
However, if it scheduled the work that might only run after everything
is said and done, which leads to cfg80211 warning that the scan isn't
reported as finished yet; this is no fault of the driver, it already
did, but mac80211 hasn't processed it.
To fix this situation, flush the delayed work when the interface being
removed is the one that was executing the scan.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the time it takes to process the beacon that started the CSA
process, we may be late for the switch if we try to reach exactly
beacon 0. To avoid that, use count - 1 when calculating the switch time.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we are switching from an HT40+ to an HT40- channel (or vice-versa),
we need the secondary channel offset IE to specify what is the
post-CSA offset to be used. This applies both to beacons and to probe
responses.
In ieee80211_parse_ch_switch_ie() we were ignoring this IE from
beacons and using the *current* HT information IE instead. This was
causing us to use the same offset as before the switch.
Fix that by using the secondary channel offset IE also for beacons and
don't ever use the pre-switch offset. Additionally, remove the
"beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not
needed anymore.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace can add keys to an AP mode interface before start_ap has been
called. If there have been no calls to start_ap/stop_ap in the mean
time, the keys will still be around when the interface is brought down.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[adjust comments, fix AP_VLAN case]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CONFIG_MAC80211_RC_MINSTREL_VHT is set, the module param
minstrel_vht_only tells minstrel_ht whether to allow the mix of ht rates
with vht rates.
ATM, minstrel_ht skips ht rates when minstrel_vht_only is true, but it does
that even if vht is not supported, which makes the sta rates fallback to
legacy as no ht rate gets enabled.
Fixes: 9208247d74 ("mac80211: minstrel_ht: add basic support for VHT rates <= 3SS@80MHz")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the callers of ieee80211_mgd_probe_ap_send return right
after they call the flush() callback. This means that calling
flush() is uneeded since its meaning is to wait until the
queues of the device are empty.
Devices that know how to report status on Tx will do so using
the regular path (ieee80211_tx_status) and this status will
trigger the continuation of the flow of the probe
(ieee80211_sta_tx_notify).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when creating virtual interfaces.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be helpful when using the mac80211_hwsim
wiphys and automated testing. Let user create the
vifs as needed, and named as expected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support creating wiphy devices with an optional name.
This will be used by hwsim to have better automated control
over virtual radio creation/deletion.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to iterate all stations currently uploaded to them.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reconfig the station list is traversed in order and station are
added back to the driver. Make sure the stations are added to the driver
in the same order they were added to mac80211.
This has a real side effect - some drivers (iwlwifi) require TDLS
stations to be added only after the AP station for the same network.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers need to know which station is the TDLS link initiator.
Expose this value via the mac80211 ieee80211_sta structure.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an IV is generated, only the MAC header is moved back. The network
header location remains the same relative to the skb head, as the new IV
is using headroom space that was reserved in advance.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Export ieee80211_ie_split function, so it can be reused by
drivers which need to insert additional elements.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When displaying a rate through debugfs minstrel_ht guesses its flags
comparing group indexes. Since 3ec373c421 ("mac80211: minstrel_ht:
include type (cck/ht) in rates flag"), the rate flags of interest are
present in the mcs_group-s, so use it.
While improving the code, this also fixes a smatch false positive
"error: testing array offset 'i' after use" in minstrel_ht_stats_dump.
This warning only triggers after 9208247d74 ("mac80211: minstrel_ht:
add basic support for VHT rates <= 3SS@80MHz") with
CONFIG_MAC80211_RC_MINSTREL_VHT unset because then MINSTREL_VHT_GROUP_0
is above MINSTREL_GROUPS_NB and smatch only barks when the "testing
array offset" seems to prevent possible out of bonds accesses (which
does not happen here since i < ARRAY_SIZE(mi->groups)).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a key is tainted during resume, it is no longer programmed
into the device; however, it's uploaded flag may (will) be set.
Clear the flag when not programming it because it's tainted to
avoid attempting to remove it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the currently existing APIs between mac80211 and the low
level driver to implement WMM admission control.
The low level driver needs to report the media time used by
each transmitted packet in ieee80211_tx_status. Based on that
information, mac80211 will modify the QoS parameters of the
admission controlled Access Category when the limit is
reached. Once the original QoS parameters can be restored,
mac80211 will do so.
One issue with this approach is that management frames will
also erroneously be downgraded, but the upside is that the
implementation is simple. In the future, it can be extended
to driver- or device-based implementations that are better.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to ever set invalid CW_min/CW_max to the
drivers, we should catch it in higher layers. However, the
consequences of setting it wrong can be quite severe, so
double-check at a low level and error out for invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The debugfs_remove() function can safely take NULL parameters
so the additionally null test isn't required, and there's no
other reason to have it here, so remove it.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
[rewrite commit message, re-introduce blank line after assert]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the new CONFIG_MAC80211_RC_MINSTREL_VHT is not set (default 'N'),
there is no behavioral change including in sampling and MCS_GROUP_RATES
remains 8.
Otherwise MCS_GROUP_RATES is 10, and a module parameter *vht_only*
(default 'true'), restricts the rates selection to VHT when VHT is
supported.
Regarding the debugfs stats buffer:
It is explicitly increased from 8k to 32k to fit every rates incl. when
both HT and VHT rates are enabled, as for the format, before:
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
after:
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
VHT40/LGI MCS5/2 0.0 0.0 0.0 0 0( 0) 0( 0)
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM, we grep cck rates idx with idx / MCS_GROUP_RATES ==
MINSTREL_CCK_GROUP.
Matching neither-cck-non-ht rates could be done by replacing '==' with
'>', however it would be less versatile or explicit.
This will allow to match VHT rates with IEEE80211_TX_RC_VHT_MCS.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No functional change.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by
throughput & probability"), the rate indexes are manipulated via u8's
and hence allow for a maximum of 256 mcs_group entries in
minstrel_mcs_groups.
ATM, minstrel_ht advertizes support up to 3HTSS@40MHz, consuming:
8(MCS_GROUP_RATES) * (3(SS)*2(GI)*2(BW)+1(CCK)), i.e. 104 entries.
Support for 3VHTSS@80MHz will require:
10(MCS_GROUP_RATES) * (3(SS)*2(GI)*2(BW)+1(CCK)) +
10(MCS_GROUP_RATES) * (3(SS)*2(GI)*3(BW)), i.e. 130 + 180 entries.
This change moves from u8s to u16s where necessary.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This showed up as a sparse warning (with higher verbosity) and is
certainly correct - the change flags should be unsigned. It's not
that important since high flag numbers aren't used and bitwise
operations would still work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM an HT rc_stats line is 106 chars.
Times 8(MCS_GROUP_RATES)*3(SS)*2(GI)*2(BW) + CCK(4), i.e. x100, this is
well above the current 8192 - sizeof(*ms) currently allocated.
Fix this by squeezing the output as follows (not that we're short on
memory but this also improves readability and range, the new format adds
one more digit to *ok/*cum and ok/cum):
- Before (HT) (106 ch):
type rate throughput ewma prob this prob retry this succ/attempt success attempts
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0 0
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0 0
- After (75 ch):
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0( 0)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
- Align non-HT format Before (non-HT) (83 ch):
rate throughput ewma prob this prob this succ/attempt success attempts
ABCDP 6 0.0 0.0 0.0 0( 0) 0 0
54 0.0 0.0 0.0 0( 0) 0 0
- After (61 ch):
rate tpt eprob *prob *ok(*cum) ok( cum)
ABCDP 1 0.0 0.0 0.0 0( 0) 0( 0)
54 0.0 0.0 0.0 0( 0) 0( 0)
*This also adds dynamic checks for overflow, lowers the size of the
non-HT request (allowing > 30 entries) and replaces the buddy-rounded
allocations (s/sizeof(*ms) + 8192/8192).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to add new parameters for the del_station calls
without having to modify all drivers that use this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It affects non-(V)HT rates and can lead to selecting an rts_cts rate
that is not a basic rate or way superior to the reference rate (ATM
rates[0] used for the 1st attempt of the protected frame data).
E.g, assuming drivers register growing (bitrate) sorted tables of
ieee80211_rate-s, having :
- rates[0].idx == d'2 and basic_rates == b'10100
will select rts_cts idx b'10011 & ~d'(BIT(2)-1), i.e. 1, likewise
- rates[0].idx == d'2 and basic_rates == b'10001
will select rts_cts idx b'10000
The first is not a basic rate and the second is > rates[0].
Also, wrt severity of the addressed misbehavior, ATM we only have one
rts_cts_rate_idx rather than one per rate table entry, so this idx might
still point to bitrates > rates[1..MAX_RATES].
Fixes: 5253ffb8c9 ("mac80211: always pick a basic rate to tx RTS/CTS for pre-HT rates")
Cc: stable@vger.kernel.org
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is okay to enable DFS for channel contexts
based drivers as long as no combination advertises
radar detection and multi-channel operation at the
same time.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to store ieee80211_vif_use_reserved_context()
result and test it before returning.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch with multiple channel contexts should now work fine.
Remove check that disallows switches when multiple contexts are in
use.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of immediately reopening the queues (in case of block_tx),
calling the post_channel_switch operation and sending the
notification, wait for the first beacon on the new channel. This
makes sure that we don't lose packets if the AP/GO is not on the new
channel yet.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a counterpart to the pre_channel_switch operation, add a
post_channel_switch operation. This allows the drivers to go back to
a normal configuration after the channel switch is completed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may need to prepare for a channel switch also when it is
initiated from the remote side (eg. station, P2P client). To make
this possible, add a generic callback that can be called for all
interface types.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Extended Channel Switching capability bit in the extended
capabilities element must be set if the driver supports CSA on
non-beaconing interfaces.
Since this capability needs to be set during driver registration, the
extended_capabiliities global variable needs to be moved to the local
structure so that it can be modified.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may need the device timestamp in order to synchronize the
channel switch. To pass this value back to the driver, add it to the
channel switch structure and copy the device_timestamp value received
in the rx info structure into it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement get_mpp and dump_mpp cfg80211_ops to export the content of the
802.11s mesh proxy path table to userspace.
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The chandef of the channel context a vif is using may be different
than the chandef of the vif itself. For instance, the bandwidth used
by the vif may be narrower than the one configured in the channel
context. To avoid confusion, return the vif's chandef in
ieee80211_cfg_get_channel() instead of the chandef of the channel
context.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by
throughput & probability") replaced the constant 8 with MCS_GROUP_RATES
when getting the number of streams of an HT MCS. See commit 7a5e3fa2c8
("mac80211: minstrel_ht: replace some occurences of MCS_GROUP_RATES").
Fixes: 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Forgot to add an entry to the struct description of sta_info.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-09-22
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
For the bluetooth bits, Johan says:
"Here are some more patches intended for 3.18. Most of them are cleanups
or fixes for SMP. The only exception is a fix for BR/EDR L2CAP fixed
channels which should now work better together with the L2CAP
information request procedure."
For the iwlwifi bits, Emmanuel says:
"I fix here dvm which was broken by my last pull request. Arik
continues to work on TDLS and Luca solved a few issues in CT-Kill. Eyal
keeps digging into rate scaling code, more to come soon. Besides this,
nothing really special here."
Beyond that, there are the usual big batches of updates to ath9k, b43,
mwifiex, and wil6210 as well as a handful of other bits here and there.
Also, rtlwifi gets some btcoexist attention from Larry.
Please let me know if there are problems!
====================
Had to adjust the wil6210 code to comply with Joe Perches's recent
change in net-next to make the netdev_*() routines return void instead
of 'int'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed.
-----BEGIN PGP SIGNATURE-----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=OPIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a possible issue with the use, or lack thereof of sk_refcnt and
sk_wmem_alloc in the wifi ack status functionality.
Specifically if a socket were to request acknowledgements, and the socket
were to have sk_refcnt drop to 0 resulting in it waiting on sk_wmem_alloc
to reach 0 it would be possible to have sock_queue_err_skb orphan the last
buffer, resulting in __sk_free being called on the socket. After this the
buffer is enqueued on sk_error_queue, however the queue has already been
flushed resulting in at least a memory leak, if not a data corruption.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new static_smps / dynamic_smps feature bits
instead of mac80211-internal hw flags.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Take the requested smps mode from the ap params
(instead of always starting with SMPS_OFF)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correctly mark the network header location in mac80211-generated TDLS
frames. These may be used by lower-level drivers.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace might need to know what queues are configured
for uapsd (e.g. for setting proper default values in tspecs).
Add this bitmap to the association event (inside wmm
nested attribute)
Add additional parameter to cfg80211_rx_assoc_resp,
and update its callers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding a timeout for tearing down a TDLS connection that
hasn't had ACKed traffic sent through it for a certain
amount of time.
Since we have no other monitoring facility to indicate the
existance (or non-existance) of a peer, this patch will
cause a peer to be considered as unavailable if for some X
time at least some Y packets have all not been ACKed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch improves the way minstrel_ht sorts rates according to throughput
and success probability. 3 FOR-loops across the entire rate and mcs group set
in function minstrel_ht_update_stats() which where used to determine the
fastest, second fastest and most robust rate are reduced to 2 FOR-loop.
The sorted list of rates according throughput is extended to the best four
rates as we need them in upcoming joint rate and power control. The sorting
is done via the new function minstrel_ht_sort_best_tp_rates(). The annotation
of those 4 best throughput rates in the debugfs file rc-stats is changes to:
"A,B,C,D", where A is the fastest rate and C the 4th fastest.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Tested-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minstrel and Mintrel_HT used there own structs to keep track of rate
statistics. Unify those variables in struct minstrel_rate_states and
move it to rc80211_minstrel.h for common usage. This is a clean-up
patch to prepare Minstrel and Minstrel_HT codebase for upcoming TPC.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When freeing the key, clear the memory to avoid having the
key material stick around in memory "forever".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at.
-----BEGIN PGP SIGNATURE-----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=gW3Y
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Two more fixes for mac80211 - one of them addresses a long-standing
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This message occasionally triggers for some people as in
https://bugzilla.redhat.com/show_bug.cgi?id=1111740 but
it's not clear which (headroom or tailroom) is at fault.
Annotate the message a bit to get more information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linux already supports 802.11h, where the access point can tell the
client to reduce its transmission power. However, 802.11h is only
defined for 5 GHz, where the need for this is much smaller than on
2.4 GHz.
Cisco has their own solution, called DTPC (Dynamic Transmit Power
Control). Cisco APs on a controller sometimes but not always send
802.11h; they always send DTPC, even on 2.4 GHz. This patch adds support
for parsing and honoring the DTPC IE in addition to the 802.11h
element (they do not always contain the same limits, so both must
be honored); the format is not documented, but very simple.
Tested (on top of wireless.git and on 3.16.1) against a Cisco Aironet
1142 joined to a Cisco 2504 WLC, by setting various transmit power
levels for the given access points and observing the results.
The Wireshark 802.11 dissector agrees with the interpretation of the
element, except for negative numbers, which seem to never happen
anyway.
Signed-off-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Decouple the logic of parsing the 802.11d and 802.11h IEs from the
part of deciding what to do about the data (messaging, clamping to
0 dBm, doing the actual setting). This paves the way for the next
patch, which introduces more data sources for transmit power limitation.
Signed-off-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit "mac80211: disable 40MHz support in case of 20MHz AP"
broke working VHT in 20Mhz with APs like Netgear R6300v2 which
do not publish support for 40Mhz but allow use of VHT in 20Mhz.
The break is because VHT is disabled once no HT cap doesn't indicate
support for 40Mhz. This causes the assoc request to be sent without
any VHT IE and the association is only HT due to this.
For more details check out commit 4a817aa7
"mac80211: allow VHT with peers not capable of 40MHz"
Fixes: 53b954ee4a ("mac80211: disable 40MHz support in case of 20MHz AP")
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the remaining time in the current roc is not long
enough, mac80211 adds the new roc right after it
(if they have similar params).
However, in case of multiple rocs, the "next roc"
is not considered, resulting in multiple rocs,
each one with its own duration.
Refactor the code a bit and consider the next roc,
so a single max roc will be used instead of
multiple rocs (which might last much longer).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new duration (remaining duration after the current
ROC ends) was calculated but not used, making the
optimization worthless.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of a RRM-supporting connection, in the association request
frame: set the RRM capability flag, and add the required IEs.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function description claimed that on error the skb isn't
freed even though it is, and stated return values that are
different than what really happens in the code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta_set_sinfo is obviously takes data for specific station.
This specific station is attached to a specific virtual
interface. Hence we should use the dtim_period from this
virtual interface rather than the system wide dtim_period.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not sure how the declaration of ieee80211_tdls_peer_del_work
landed after the double inclusion protection end.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs.
-----BEGIN PGP SIGNATURE-----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=G/pB
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
When starting an offloaded BA session it is
unknown what starting sequence number should be
used. Using last_seq worked in most cases except
after hw restart.
When hw restart is requested last_seq is
(rightfully so) kept unmodified. This ended up
with BA sessions being restarted with an aribtrary
BA window values resulting in dropped frames until
sequence numbers caught up.
Instead of last_seq pick seqno of a first Rxed
frame of a given BA session.
This fixes stalled traffic after hw restart with
offloaded BA sessions (currently only ath10k).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a device driver is unloaded local->interfaces
list is cleared. If there was more than 1
interface running and connected (bound to a
chanctx) then chantype recalc was called and it
ended up with compat being NULL causing a call
trace warning.
Warn if compat becomes NULL as a result of
incompatible bss_conf.chandef of interfaces bound
to a given channel context only.
The call trace looked like this:
WARNING: CPU: 2 PID: 2594 at /devel/src/linux/net/mac80211/chan.c:557 ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0()
Modules linked in: ath10k_pci(-) ath10k_core ath
CPU: 2 PID: 2594 Comm: rmmod Tainted: G W 3.16.0-rc1+ #150
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
0000000000000009 ffff88001ea279c0 ffffffff818dfa93 0000000000000000
ffff88001ea279f8 ffffffff810514a8 ffff88001ce09cd0 ffff88001e03cc58
0000000000000000 ffff88001ce08840 ffff88001ce09cd0 ffff88001ea27a08
Call Trace:
[<ffffffff818dfa93>] dump_stack+0x4d/0x66
[<ffffffff810514a8>] warn_slowpath_common+0x78/0xa0
[<ffffffff81051585>] warn_slowpath_null+0x15/0x20
[<ffffffff818a407d>] ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0
[<ffffffff818a3dda>] ? ieee80211_recalc_chanctx_chantype+0x2a/0x2e0
[<ffffffff818a4919>] ieee80211_assign_vif_chanctx+0x1a9/0x770
[<ffffffff818a6220>] __ieee80211_vif_release_channel+0x70/0x130
[<ffffffff818a6dd3>] ieee80211_vif_release_channel+0x43/0xb0
[<ffffffff81885f4e>] ieee80211_stop_ap+0x21e/0x5a0
[<ffffffff8184b9b5>] __cfg80211_stop_ap+0x85/0x520
[<ffffffff8181c188>] __cfg80211_leave+0x68/0x120
[<ffffffff8181c268>] cfg80211_leave+0x28/0x40
[<ffffffff8181c5f3>] cfg80211_netdev_notifier_call+0x373/0x6b0
[<ffffffff8107f965>] notifier_call_chain+0x55/0x110
[<ffffffff8107fa41>] raw_notifier_call_chain+0x11/0x20
[<ffffffff816a8dc0>] call_netdevice_notifiers_info+0x30/0x60
[<ffffffff816a8eb9>] __dev_close_many+0x59/0xf0
[<ffffffff816a9021>] dev_close_many+0x81/0x120
[<ffffffff816aa1c5>] rollback_registered_many+0x115/0x2a0
[<ffffffff816aa3a6>] unregister_netdevice_many+0x16/0xa0
[<ffffffff8187d841>] ieee80211_remove_interfaces+0x121/0x1b0
[<ffffffff8185e0e6>] ieee80211_unregister_hw+0x56/0x110
[<ffffffffa0011ac4>] ath10k_mac_unregister+0x14/0x60 [ath10k_core]
[<ffffffffa0014fe7>] ath10k_core_unregister+0x27/0x40 [ath10k_core]
[<ffffffffa003b1f4>] ath10k_pci_remove+0x44/0xa0 [ath10k_pci]
[<ffffffff81373138>] pci_device_remove+0x28/0x60
[<ffffffff814cb534>] __device_release_driver+0x64/0xd0
[<ffffffff814cbcc8>] driver_detach+0xb8/0xc0
[<ffffffff814cb23a>] bus_remove_driver+0x4a/0xb0
[<ffffffff814cc697>] driver_unregister+0x27/0x50
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "rcu_dereference()" calls are used directly in conditions.
Since their return values are never dereferenced it is recommended to
use "rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacements.
The following Coccinelle semantic patch was used:
@@
@@
(
if(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
|
while(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Header-less cloned skbs with sufficient headroom need not be cloned
unless the tailroom is going to be modified.
Fix ieee80211_skb_resize so it would only resize cloned skbs if either
the header isn't released or the tailroom is going to be modified.
Some drivers might have assumed that skbs are never cloned, so add a HW
flag that explicitly permits cloned TX skbs. Drivers which do not modify
TX skbs should set this flag to avoid copying skbs.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
will only require headroom space. Consequently, the tailroom-needed
counter can safely be decremented.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "RX active" string is too long, so the columns get
shifted. Change it to just "RX" to avoid this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta->last_seq_ctrl is the seq_ctrl field from the last header
seen, need to shift it 4 bits to extract the sequence number.
Otherwise the ieee80211_sn_less() check at the top of
ieee80211_sta_manage_reorder_buf drops frames until the sequence
number catches up.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 802.11 standard says when processing a plink confirm
frame:
"If the peerLinkID in the mesh peering instance has not been
set, the Local Link ID field of the Mesh Peering Confirm
request shall be copied into the peerLinkID in the mesh
peering instance."
We were only doing this when receiving an open peering frame,
but it could happen that the open frame gets lost and so we
should handle this case rather than rejecting the confirm and
failing the whole peering process.
Reported-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_sta_ps_deliver_wakeup, sdata->smps_mode is checked. This is
initialized only for the base AP interface, not the individual VLANs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When bringing down the AP, a WARN_ON is hit because the bss config chandef
is empty here.
Since AP_VLAN channel settings do not matter for anything chanctx related
(always inherits the settings from the AP interface), let's just ignore
it here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 24aa11ab8a.
That commit was wrong since it uses data that hasn't even been set
up yet, but might be a hold-over from a previous connection.
Additionally, it seems like a driver-specific workaround that
shouldn't have been in mac80211 to start with.
Cc: stable@vger.kernel.org
Fixes: 24aa11ab8a ("mac80211: disable uAPSD if all ACs are under ACM")
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new_ctx pointer is set only for non-chanctx drivers. This yielded a
crash for chanctx-based drivers during channel switch finalization:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]
Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the AP only advertises support for 20MHz (in the
ht operation ie), disable 40MHz and VHT.
This can improve interoperability with APs that
don't like stations exceeding their own
advertised capabilities.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently track the QoS capability twice: for all peer stations
in the WLAN_STA_WME flag, and for any clients associated to an AP
interface separately for drivers in the sta->sta.wme field.
Remove the WLAN_STA_WME flag and track the capability only in the
driver-visible field, getting rid of the limitation that the field
is only valid in AP mode.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the expected throughput is queried before rate control has been
initialized, the minstrel op for it will crash while trying to access
the rate table.
Check for WLAN_STA_RATE_CONTROL before attempting to use the rate
control op.
Reported-by: Jean-Pierre Tosoni <jp.tosoni@acksys.fr>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sdata can't be NULL, and key being NULL is really not possible
unless the code is modified.
The sdata check made a static analyze (klocwork) unhappy because
we would get pointer to local (sdata->local) and only then check
if sdata is non-NULL.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove !key check as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NULL pointer access could happen when ieee80211_crypto_hw_decrypt
is called from ieee80211_rx_h_decrypt with the following condition:
1. rx->key->conf.cipher is not WEP, CCMP, TKIP or AES_CMAC
2. rx->sta is NULL
When ieee80211_crypto_hw_decrypt is called, it verifies
rx->sta->cipher_scheme and it will cause Oops if rx->sta is NULL.
This path adds an addirional rx->sta == NULL verification in
ieee80211_crypto_hw_decrypt for this case.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa_active flag was added in sdata a while ago and made
IEEE80211_STA_CSA_RECEIVED redundant. The new flag is also used to
mark when CSA is ongoing on other iftypes and took over the old one as
the preferred method for checking whether we're in the middle of a
channel switch. Remove the old, redundant flag.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the teardown packet is created while the queues are
stopped, it isn't sent immediately, but rather is pending.
To be sure that when we flush the queues prior to destroying
the station we also send this packet - the tasklet handling
pending packets is invoked to flush the packets.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: ArikX Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP receives actions frames destined for other peers, it may
mistakenly toggle BA-sessions from itself to a peer.
Ignore TDLS data packets as well - the AP should not handle them.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TDLS VHT support requires some more information elements during setup.
While these are not there, mask out the peer's VHT capabilities so that
VHT rates are not mistakenly used.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set for completeness mostly, currently unused in the code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the HT capabilities and HT operation information elements to TDLS
setup packets where appropriate.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can only be a station for TDLS connections. Also fix a bug where
a delayed work could be left scheduled if the station interface was
brought down during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TDLS QoS is supported by the the peer and the local card, add
the WMM parameter IE to the setup-confirm frame. Take the QoS settings
from the current AP, or if unsupported, use the default values from
the specification. This behavior is mandated by IEEE802.11-2012 section
10.22.4.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS is supported by the card, add an appropriate IE to TDLS setup-
request and setup-response frames.
Consolidate the setting of the WMM info IE across mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending setup-failure frames, set the capability field to zero, as
mandated by the specification (IEEE802.11-2012 8.5.13).
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most setup-specific information elements are not to be added when a
setup frame is sent with an error status code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building TDLS setup frames, use the IE order mandates in the
specification, splitting extra IEs coming from usermode.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add all information elements for TDLS discovery and setup in the same
function.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
