Add new compatible for wilc1000 devices and specify the delay in .data
member of struct of_device_id. WILC1000, WILC3000 devices needs a minimum
of 5ms delay b/w reset and power lines.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210820092803.78523-3-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to SD specification checking state of DAT0 only, is enough while
polling for card busy completion. Let's update the comment in the header
file to correct this, as the comment says DAT[0:3].
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20210816153054.24082-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching card voltage to UHS voltage the mmc framework tries to
check the card busy signal, meaning the card pulling DAT0 line low,
before the switch is made. Drivers that does not implement the card_busy
function will manage to do the switch anyway, but the framework will
print a warning about not being able to verify the voltage signal.
Implement card_busy function.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20210816142314.1168-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci use PIO mode, and use mmc_send_tuning() to send the tuning
command, system will stuck because of the storm irq of sdhci. For PIO mode,
use mmc_send_tuning(), it will trigger buffer_read_ready interrupt and data
transfer complete interrupt. In current code logic, it will directly
return in sdhci_data_irq, can not call the sdhci_transfer_pio(). So the
buffer_read_ready interrupt storm happen. So for standard tuning method,
need to exclude this case.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628858041-1911-1-git-send-email-haibo.chen@nxp.com
[Ulf: Dropped redundant parenthesis in an expression]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor renesas_sdhi_probe() to avoid increasing numbers of
sdhi_quirks_match[] entry when we add other stable SoCs like
r8a779m*.
Note that the sdhi_quirks_match[] is only needed on
renesas_sdhi_internal_dmac.c so that of_data of
renesas_sdhi_sys_dmac.c keeps as-is.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210729103234.480743-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For dw_mmc, this is probably not currently an issue but is still good to
fix though.
Fixes: 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface support")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures at least if external TI SDMA is ever configured for sdhci.
For other external DMA cases, this is probably not currently an issue but
is still good to fix though.
Fixes: 18e762e3b7 ("mmc: sdhci: add support for using external DMA devices")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210810081644.19353-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Qcom SD controller defines the usage of 0xF in data
timeout counter register (0x2E) which is actually a reserved
bit as per specification. This would result in maximum of 21.26 secs
timeout value.
Some SDcard taking more time than 2.67secs (timeout value corresponding
to 0xE) and with that observed data timeout errors.
So increasing the timeout value to max possible timeout.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-3-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce max_timeout_count variable in the sdhci_host structure
and use in timeout calculation. By default its set to 0xE
(max timeout register value as per SDHC spec). But at the same time
vendors drivers can update it if they support different max timeout
register value than 0xE.
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-2-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Print out the contents of the offending tuples when we do print them.
This can make it easier to debug, since these tuples are not exposed to
userspace anywhere else. We are limited to 64 bytes, so keep printing
out the full length in case the tuple is truncated.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-2-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CIS tuples in the range 0x80-0x8F are reserved for vendors. Some devices
have tuples in this range which get warned about every boot. Since this
is normal behavior, don't print these tuples unless debug is enabled.
Unfortunately, we cannot use a variable for the format string since it
gets pasted by pr_*_ratelimited.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-1-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Skip printing a retune error when we scan for a removed card because we
then expect a failed command.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210630041658.7574-1-wsa+renesas@sang-engineering.com
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.
This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard. Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.
Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard. Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the i.MX conversion to a DT-only platform, the mmc-esdhc-imx.h
header file is no longer used outside the driver, so move its content
to the sdhci-esdhc-imx driver and remove the header.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210719193413.3792615-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org
When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org
When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org
This driver has had problems when handling data errors. Add fault
injection support so that the abort handling can be easily triggered and
regression-tested. A hrtimer is used to indicate a data CRC error at
various points during the data transfer.
Note that for the recent problem with hangs in the case of some data CRC
errors, a udelay(10) inserted at the start of send_stop_abort() greatly
helped in triggering the error, but I've not included this as part of
the fault injection support since it seemed too specific.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Infinite loops are hard to read and understand because of
hidden main loop condition. Simplify such one in mmc_spi_skip().
Using schedule() to schedule (and be friendly to others)
is discouraged and cond_resched() should be used instead.
Hence, replace schedule() with cond_resched() at the same
time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210623101731.87885-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we find a reset handle when probing the MMCI block,
make sure the reset is de-asserted. It could happen that
a hardware has reset asserted at boot.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yann Gautier <yann.gautier@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210630102408.3543024-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095734.3046-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'of_property_read_variable_u32_array' function returns number
of elements read on success. This patch updates the condition
check in the driver to overwrite the tap values from DT if exist.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-8-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modify the data type of the clk_phase array to u32 to make it compatible
with the argument requirement of "of_property_read_variable_u32_array".
Addresses-coverity: ("incompatible_param")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-7-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The division macro DIV_ROUND_CLOSEST takes int values as the argument.
However the code here uses unsigned int values for this, which is
causing the values comparison with 0 as always true. We can use
DIV_ROUND_CLOSEST_ULL instead for the same.
Addresses-coverity: ("result_independent_of_operands")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-6-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.
Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ZynqMP platform does not perform auto tuning in DDR50 mode. Skip the
same while the card is operating in DDR50 mode.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Arasan controller supports AUTO CMD12, this patch adds
"SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12" quirk to enable auto cmd12
feature.
By using auto cmd12 we can also avoid following error message
"Got data interrupt even though no data operation in progress"
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD standard speed timing was met only at 19MHz and not 25 MHz, that's
why changing driver to 19MHz. The reason for this is when a level shifter
is used on the board, timing was met for standard speed only at 19MHz.
Since this level shifter is commonly required for high speed modes,
the driver is modified to use standard speed of 19Mhz.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have this in two places, so let's have a dedicated function. It is
also more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I wanted to use it in a wrong way, so document the intended way.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Fix random crashes on some 32-bit CPUs by adding isync() after locking/unlocking KUEP
- Fix intermittent crashes when loading modules with strict module RWX
- Fix a section mismatch introduce by a previous fix.
Thanks to: Christophe Leroy, Fabiano Rosas, Laurent Vivier, Murilo Opsfelder Araújo,
Nathan Chancellor, Stan Johnson.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAmEhjVUTHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgM/VD/4o5D9d2Xppt+T0zdnKomq+3ffkC33/
zBK4vqOVOXbnlRpChqIqsHB3LNxMNMvTVaoLvxgy3ZQ57+rnirSDaFOaj4Nbazdx
STwWmyxW9xPshqvj8tz8uHadSkvbrCClFy59FXtJf4H/iztTnQORKnXI9r3wxXS+
wBhw8Nhquuqg4O5h4q6yLLRIAaskus7uymDzYHVZkHO0RhfPLEZJwfCxydc29ukK
wIRB6qojFBbWm/UscY1w6FiYrBn4Y5F3DzoTzJ7xlO6l1NYaE+58aun/oTGU7922
/8fXYs34TnkF6sA9qGhOtOc1MXfH8meFoH9s/fY3Z3O88xTe8k15wo2Ujlk/u0X1
1Gzv9FZI0RnpPtSLPiiu72/zS/vFOxAVCFMTvcodlte9RN90fW5Qwt/O1ya22vWt
Ea3O9iNmYgQ+lV7ZZYDtKQ22WHIublg6cY5d3NDyj5HrzN/vGyp3QJFb2dnWoEpx
k/KkK16oiIlduLGiFoYjn1ELyHUBTvp483y7zmspA4fCb0ue6W8b2zt8FszH0hI7
N4uroGXuk9OyhNsLWR8UHUR0s6Gi0XSaQ0O4XgWfoDAAvdev4oZiCqw0q5552OvX
eE/Ogxc7INCiaoeLwOhYhCKjr+jBP8fhqyQzquyqMgUqEbxLtcFZCJ09bpXHjjiH
OlAvZwlzOhwcKg==
=K2B0
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix random crashes on some 32-bit CPUs by adding isync() after
locking/unlocking KUEP
- Fix intermittent crashes when loading modules with strict module RWX
- Fix a section mismatch introduce by a previous fix.
Thanks to Christophe Leroy, Fabiano Rosas, Laurent Vivier, Murilo
Opsfelder Araújo, Nathan Chancellor, and Stan Johnson.
h# -----BEGIN PGP SIGNATURE-----
* tag 'powerpc-5.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix set_memory_*() against concurrent accesses
powerpc/32s: Fix random crashes by adding isync() after locking/unlocking KUEP
powerpc/xive: Do not mark xive_request_ipi() as __init
- Make the regulator state match the GDSC power domain state at boot
on Qualcomm SoCs so that the regulator isn't turned off
inadvertently.
- Fix earlycon on i.MX6Q SoCs
-----BEGIN PGP SIGNATURE-----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=EGjz
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
- Make the regulator state match the GDSC power domain state at boot on
Qualcomm SoCs so that the regulator isn't turned off inadvertently.
- Fix earlycon on i.MX6Q SoCs
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gdsc: Ensure regulator init state matches GDSC state
clk: imx6q: fix uart earlycon unwork
Here are some small driver fixes for 5.14-rc7.
They consist of:
- revert for an interconnect patch that was found to have
problems.
- ipack tpci200 driver fixes for reported problems
- slimbus messaging and ngd fixes for reported problems.
All are small and have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYSEfhw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylxAQCfYvG2nCMkIvBi7MXNwRS0go5YJyAAn3RprTCU
V7dduATGH8zJ4u6AOdtg
=Uq3v
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 5.14-rc7.
They consist of:
- revert for an interconnect patch that was found to have problems
- ipack tpci200 driver fixes for reported problems
- slimbus messaging and ngd fixes for reported problems
All are small and have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
ipack: tpci200: fix memory leak in the tpci200_register
ipack: tpci200: fix many double free issues in tpci200_pci_probe
slimbus: ngd: reset dma setup during runtime pm
slimbus: ngd: set correct device for pm
slimbus: messaging: check for valid transaction id
slimbus: messaging: start transaction ids from 1 instead of zero
Revert "interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate"
Here is a single USB typec tcpm fix for a reported problem for 5.14-rc7.
It showed up in 5.13 and resolves an issue that Hans found. It has been
in linux-next this week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYSEgIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymZpQCfeD9XR0ExAJgn7E0sNuLaOi2BxmUAn3Eu2IFu
dFcSEpQtg23mY6aBFWfH
=7kfD
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fix from Greg KH:
"Here is a single USB typec tcpm fix for a reported problem for
5.14-rc7. It showed up in 5.13 and resolves an issue that Hans found.
It has been in linux-next this week with no reported problems"
* tag 'usb-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: Fix VDMs sometimes not being forwarded to alt-mode drivers
* A fix to the sifive-l2-cache device tree bindings, for json-schema
compatibility. This does not change the intended behavior of the
binding.
* A fix to avoid improperly freeing necessary resources during early
boot.
-----BEGIN PGP SIGNATURE-----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=xEwN
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- fix the sifive-l2-cache device tree bindings for json-schema
compatibility. This does not change the intended behavior of the
binding.
- avoid improperly freeing necessary resources during early boot.
* tag 'riscv-for-linus-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix a number of free'd resources in init_resources()
dt-bindings: sifive-l2-cache: Fix 'select' matching
