this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Keystone SOCs, ARM host can send interrupts to DSP cores using the
DSP GPIO controller IP. Each DSP GPIO controller provides 28 IRQ signals for
each DSP core. This is one of the component used by the IPC mechanism used
on Keystone SOCs.
Keystone 2 DSP GPIO controller has specific features:
- each GPIO can be configured only as output pin;
- setting GPIO value to 1 causes IRQ generation on target DSP core;
- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still
pending.
This patch updates gpio-syscon driver to be reused by Keystone 2 SoCs,
because the Keystone 2 DSP GPIO controller is controlled through Syscon
devices and, as requested by Linus Walleij, such kind of GPIO controllers
should be integrated with drivers/gpio/gpio-syscon.c driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds handling of new "gpio,syscon-dev" DT property,
which allows to specify syscon node and data/direction registers
offsets in DT.
"gpio,syscon-dev" has following format:
gpio,syscon-dev = <&syscon_dev data_reg_offset [direction_reg_offset]>;
where
- syscon_dev - phandle on syscon node
- data_reg_offset - offset of data register (in bytes)
- direction_reg_offset - offset of dirrection register (optional, in bytes)
for example:
gpio,syscon-dev = <&devctrl 0x254>;
In such way, the support of multiple Syscon GPIO devices is added.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs (like Keystone) may require to perform special
sequence of operations to assign output GPIO value, so default
implementation of .set() callback from gpio-syscon driver
can't be used.
Hence, add optional, SoC specific callback to assign output
gpio value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Device tree is not enabled in some architecture where gpio
driver mcp23s08 is still required.
v2-changes:
- Parse device tree properties into platform data other than
individual variables.
v3-changes:
- Use of_node in gpio_chip device structure, because the
struct device * always has an of_node which is NULL when
OF is not used.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of unmask/mask in set_wake was an incorrect implementation. The new
implementation correctly sets wakeup for the gpio chip's IRQ so the gpio chip
will not sleep while wakeup-enabled gpio are in use.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added flag to the GPIO chip so that IRQ from non-wakeup GPIO will
not wake the system.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When looking up the IRQ the bank offset needs to be taken into account.
Otherwise interrupts for banks other than bank 0 get incorrectly reported as
interrupts for bank 0.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the ADNP GPIO driver to use the gpiolib
irqchip helpers. Also do some random refactoring to make it
look like most other GPIO drivers.
Cc: Roland Stigge <stigge@antcom.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current prototype of gpiochip_request_own_desc() requires to obtain
a pointer to a descriptor. This is in contradiction to all other GPIO
request schemes, and imposes an extra step of obtaining a descriptor to
drivers. Most drivers actually cannot even perform that step since the
function that does it (gpichip_get_desc()) is gpiolib-private.
Change gpiochip_request_own_desc() to return a descriptor from a
(chip, hwnum) tuple and update users of this function (currently
gpiolib-acpi only).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO descriptors are changing from unique and permanent tokens to
allocated resources. Therefore gpiochip_get_desc() cannot be used as a
way to obtain a global GPIO descriptor anymore.
This patch updates the gpiolib ACPI support code to keep and use the
descriptor returned by a centralized call to gpiochip_get_desc().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
zynq_gpio_irqhandler() uses up to 7 tabs of indention in some parts. Refactor
things to use a helper function for the inner loop to reduce the indention to a
sane level.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add another example to describe bindings that work for PXA3xx boards.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a devicetree binding documentation for the pca953x driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop deprecated DT bindings and use automaticly assigned gpio and irq
bases.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Highlights:
- More fixes for read/write codepath regressions
- Sleeping while holding the inode lock
- Stricter enforcement of page contiguity when coalescing requests
- Fix up error handling in the page coalescing code
- Don't busy wait on SIGKILL in the file locking code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2wRt
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highlights:
- more fixes for read/write codepath regressions
* sleeping while holding the inode lock
* stricter enforcement of page contiguity when coalescing requests
* fix up error handling in the page coalescing code
- don't busy wait on SIGKILL in the file locking code"
* tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
nfs: can_coalesce_requests must enforce contiguity
nfs: disallow duplicate pages in pgio page vectors
nfs: don't sleep with inode lock in lock_and_join_requests
nfs: fix error handling in lock_and_join_requests
nfs: use blocking page_group_lock in add_request
nfs: fix nonblocking calls to nfs_page_group_lock
nfs: change nfs_page_group_lock argument
* Confine SH_INTC to platforms that need it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QSyy
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH driver fix from Simon Horman:
"Confine SH_INTC to platforms that need it"
* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
sh: intc: Confine SH_INTC to platforms that need it
Pull MIPS fixes from Ralf Baechle:
"Pretty much all across the field so with this we should be in
reasonable shape for the upcoming -rc2"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: OCTEON: make get_system_type() thread-safe
MIPS: CPS: Initialize EVA before bringing up VPEs from secondary cores
MIPS: Malta: EVA: Rename 'eva_entry' to 'platform_eva_init'
MIPS: EVA: Add new EVA header
MIPS: scall64-o32: Fix indirect syscall detection
MIPS: syscall: Fix AUDIT value for O32 processes on MIPS64
MIPS: Loongson: Fix COP2 usage for preemptible kernel
MIPS: NL: Fix nlm_xlp_defconfig build error
MIPS: Remove race window in page fault handling
MIPS: Malta: Improve system memory detection for '{e, }memsize' >= 2G
MIPS: Alchemy: Fix db1200 PSC clock enablement
MIPS: BCM47XX: Fix reboot problem on BCM4705/BCM4785
MIPS: Remove duplicated include from numa.c
MIPS: Add common plat_irq_dispatch declaration
MIPS: MSP71xx: remove unused plat_irq_dispatch() argument
MIPS: GIC: Remove useless parens from GICBIS().
MIPS: perf: Mark pmu interupt IRQF_NO_THREAD
separate trampolines had a design flaw with the interaction between
the function and function_graph tracers.
The main flaw was the simplification of the use of multiple tracers having
the same filter (like function and function_graph, that use the
set_ftrace_filter file to filter their code). The design assumed that the
two tracers could never run simultaneously as only one tracer can be
used at a time. The problem with this assumption was that the function
profiler could be implemented on top of the function graph tracer, and
the function profiler could run at the same time as the function tracer.
This caused the assumption to be broken and when ftrace detected this
failed assumpiton it would spit out a nasty warning and shut itself down.
Instead of using a single ftrace_ops that switches between the function
and function_graph callbacks, the two tracers can again use their own
ftrace_ops. But instead of having a complex hierarchy of ftrace_ops,
the filter fields are placed in its own structure and the ftrace_ops
can carefully use the same filter. This change took a bit to be able
to allow for this and currently only the global_ops can share the same
filter, but this new design can easily be modified to allow for any
ftrace_ops to share its filter with another ftrace_ops.
The first four patches deal with the change of allowing the ftrace_ops
to share the filter (and this needs to go to 3.16 as well).
The fifth patch fixes a bug that was also caused by the new changes
but only for archs other than x86, and only if those archs implement
a direct call to the function_graph tracer which they do not do yet
but will in the future. It does not need to go to stable, but needs
to be fixed before the other archs update their code to allow direct
calls to the function_graph trampoline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT+hqSAAoJEKQekfcNnQGulvcH/0O4NMXX4HH1dQlYgKEaSYxE
Nh8WdiewopF5iaeNvo+8Nzdq8D2k3KgMOqSlzJ4JVmzd7gjOBSGeKDfqFwR+IbTk
9LcaJJCI3oG3MEf6m7gZMdjKPKyxkeYHDtG7kRHo8z94eliV9pKC6fUnEWayQO3o
Kv6IBupdkF8ICAiKRae5Uo0c9wjZ9YP0bZS7fxI2hJw3h/NMFnhnhUL03URIx8e3
dqgpweYg+P3KPfp2Jz6safdJqLTPK9rqqhkZhylbDl7o78xEzRN7wCyB6Nak00xz
swRgsW6vFP7ci/YSNx+B6HCIf7NTm3WLDrrIhitNHcJUZwUMU3CRO9IJHGsTuEE=
=J5lZ
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull fix for ftrace function tracer/profiler conflict from Steven Rostedt:
"The rewrite of the ftrace code that makes it possible to allow for
separate trampolines had a design flaw with the interaction between
the function and function_graph tracers.
The main flaw was the simplification of the use of multiple tracers
having the same filter (like function and function_graph, that use the
set_ftrace_filter file to filter their code). The design assumed that
the two tracers could never run simultaneously as only one tracer can
be used at a time. The problem with this assumption was that the
function profiler could be implemented on top of the function graph
tracer, and the function profiler could run at the same time as the
function tracer. This caused the assumption to be broken and when
ftrace detected this failed assumpiton it would spit out a nasty
warning and shut itself down.
Instead of using a single ftrace_ops that switches between the
function and function_graph callbacks, the two tracers can again use
their own ftrace_ops. But instead of having a complex hierarchy of
ftrace_ops, the filter fields are placed in its own structure and the
ftrace_ops can carefully use the same filter. This change took a bit
to be able to allow for this and currently only the global_ops can
share the same filter, but this new design can easily be modified to
allow for any ftrace_ops to share its filter with another ftrace_ops.
The first four patches deal with the change of allowing the ftrace_ops
to share the filter (and this needs to go to 3.16 as well).
The fifth patch fixes a bug that was also caused by the new changes
but only for archs other than x86, and only if those archs implement a
direct call to the function_graph tracer which they do not do yet but
will in the future. It does not need to go to stable, but needs to be
fixed before the other archs update their code to allow direct calls
to the function_graph trampoline"
* tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Use current addr when converting to nop in __ftrace_replace_code()
ftrace: Fix function_profiler and function tracer together
ftrace: Fix up trampoline accounting with looping on hash ops
ftrace: Update all ftrace_ops for a ftrace_hash_ops update
ftrace: Allow ftrace_ops to use the hashes from other ops
Pull x86 fixes from Ingo Molnar:
"A couple of EFI fixes, plus misc fixes all around the map"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Store Runtime Services revision
firmware: Do not use WARN_ON(!spin_is_locked())
x86_32, entry: Clean up sysenter_badsys declaration
x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
x86/mm: Fix RCU splat from new TLB tracepoints
Pull perf fixes from Ingo Molnar:
"A kprobes and a perf compat ioctl fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Handle compat ioctl
kprobes: Skip kretprobe hit in NMI context to avoid deadlock
A collection of fixes from this week, it's been pretty quiet and nothing
really stands out as particularly noteworthy here -- mostly minor fixes
across the field:
- ODROID booting was fixed due to PMIC interrupts missing in DT
- A collection of i.MX fixes
- Minor Tegra fix for regulators
- Rockchip fix and addition of SoC-specific mailing list to make it
easier to find posted patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+oYu
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes from this week, it's been pretty quiet and
nothing really stands out as particularly noteworthy here -- mostly
minor fixes across the field:
- ODROID booting was fixed due to PMIC interrupts missing in DT
- a collection of i.MX fixes
- minor Tegra fix for regulators
- Rockchip fix and addition of SoC-specific mailing list to make it
easier to find posted patches"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Fix warning message
ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
ARM: dts: ODROID i2c improvements
ARM: dts: Enable PMIC interrupts on ODROID
ARM: dts: imx6sx: fix the pad setting for uart CTS_B
ARM: dts: i.MX53: fix apparent bug in VPU clks
ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
ARM: dts: imx6: edmqmx6: change enet reset pin
ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
ARM: imx: remove unnecessary ARCH_HAS_OPP select
ARM: imx: fix TLB missing of IOMUXC base address during suspend
ARM: imx6: fix SMP compilation again
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
- A largeish fix for the IRQ handling in the new Zynq driver.
The quite verbose commit message gives the exact details.
- Move some defines for gpiod flags outside an ifdef to make
stub functions work again.
- Various minor fixes that we can accept for -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7iYA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- a largeish fix for the IRQ handling in the new Zynq driver. The
quite verbose commit message gives the exact details.
- move some defines for gpiod flags outside an ifdef to make stub
functions work again.
- various minor fixes that we can accept for -rc1.
* tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio-lynxpoint: enable input sensing in resume
gpio: move GPIOD flags outside #ifdef
gpio: delete unneeded test before of_node_put
gpio: zynq: Fix IRQ handlers
gpiolib: devres: use correct structure type name in sizeof
MAINTAINERS: Change maintainer for gpio-bcm-kona.c
Pull drm fixes from Dave Airlie:
"Intel and radeon fixes.
Post KS/LC git requests from i915 and radeon stacked up. They are all
fixes along with some new pci ids for radeon, and one maintainers file
entry.
- i915: display fixes and irq fixes
- radeon: pci ids, and misc gpuvm, dpm and hdp cache"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
MAINTAINERS: Add entry for Renesas DRM drivers
drm/radeon: add additional SI pci ids
drm/radeon: add new bonaire pci ids
drm/radeon: add new KV pci id
Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
drm/radeon: fix active cu count for SI and CIK
drm/radeon: re-enable selective GPUVM flushing
drm/radeon: Sync ME and PFP after CP semaphore waits v4
drm/radeon: fix display handling in radeon_gpu_reset
drm/radeon: fix pm handling in radeon_gpu_reset
drm/radeon: Only flush HDP cache for indirect buffers from userspace
drm/radeon: properly document reloc priority mask
drm/i915: don't try to retrain a DP link on an inactive CRTC
drm/i915: make sure VDD is turned off during system suspend
drm/i915: cancel hotplug and dig_port work during suspend and unload
drm/i915: fix HPD IRQ reenable work cancelation
drm/i915: take display port power domain in DP HPD handler
drm/i915: Don't try to enable cursor from setplane when crtc is disabled
drm/i915: Skip load detect when intel_crtc->new_enable==true
...
As reported by Dan Aloni, commit f8567a3845 ("aio: fix aio request
leak when events are reaped by userspace") introduces a regression when
user code attempts to perform io_submit() with more events than are
available in the ring buffer. Reverting that commit would reintroduce a
regression when user space event reaping is used.
Fixing this bug is a bit more involved than the previous attempts to fix
this regression. Since we do not have a single point at which we can
count events as being reaped by user space and io_getevents(), we have
to track event completion by looking at the number of events left in the
event ring. So long as there are as many events in the ring buffer as
there have been completion events generate, we cannot call
put_reqs_available(). The code to check for this is now placed in
refill_reqs_available().
A test program from Dan and modified by me for verifying this bug is available
at http://www.kvack.org/~bcrl/20140824-aio_bug.c .
Reported-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Dan Aloni <dan@kernelim.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: stable@vger.kernel.org # v3.16 and anything that f8567a3845 was backported to
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A message warning a user about wrong vc value was printing
out port instead.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:
pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table
Remove it to fix this.
Fixes: commit 1d41f36a68 ("ARM: shmobile:
koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.
(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)
Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
dts files and addition of the new Rockchip list to MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJT+hwkAAoJEPOmecmc0R2Bda4IAJ7rxypWxi8RtfxULHu1oGxZ
cdmAsaedAkjTn6tye/99lv1WkLzUD+Q3AxLX6Glu8PgTkocbwtkVTP+gMbv7zwfN
Z9bA6kazPL4Rskr6Am8BFKkGhXHCXChGP1J3z9Gyh07Vu2+3zsvRzyM7hySt3TqZ
EA2dL/uODlukw6EPzFaqGWZLn1OuJmkHXDfnZ3lBI/GFZD9qt5DnYswMBlDlIwr6
D08jmcleRA3wpnY1HXYR2cN1sJmcEP6xVE8ApXd71X0MtumEy49ZTR+4T5/Sh/XN
OPheoH3UUVtXVrAa5fsoUE2xsKs3PZgnIHk1kQklpbw+HArbN+aW0Jh6CySb65Q=
=aNJj
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:
Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.
* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull just contains some new pci ids.
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add additional SI pci ids
drm/radeon: add new bonaire pci ids
drm/radeon: add new KV pci id
During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.
This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only a single patch in here that fixes a DTC warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT2hD6AAoJEBx+YmzsjxAgV9YP/1wML2m04CODnLmLhKyx1GyM
VyBoEHb+o7P7TRyK7ePIVkGhGnQjYGMyXAI2KfOiBJpAl23uxXCXSNKc6WY+nBAw
6T6qL6w+tPIPW4B79fAjmoPksqhoVf9sAKAkdu6+ETwKMHRaF0IesPRTg9t21Wcd
yHHDY4z/qaFCMV59zeOIWMxM0V0gvUa46+bXC2flyTcTz5RgyUswCOXKHLvXfK1L
w8B+V34AeBtm2EzG6co1iOJVRKXlrjzUg25+adbRissNfvmVkPwYkQJNoBO6r/PO
Rxf7Mq50oovPl/Oc83e3RZl3tE8ds12t+ScS0qUFq6+tBvyq53IYP+51IhDOGiR3
a6PB1nPEXtvUt09xv5SPJiRsB+BFrh5hx+qWbDvUNQL5FZrqBxa63H6qArybFQXg
GaY8Zv5gdiMvAU0tdk7v4pduJkvvoG2GALGHPrcKmrpg2+qQ4LDKOJxErIEqOUi2
ERp7c0kODDz18F9OmjGYU2R7XT6Ji8h4MS/hbCiLajcboQMe3yClrcVB8ts+AUKJ
NSDWl5Q0/8uHhk40FAaGYEqVLakk8vhXwdg1hpcXzIg3dJg+P09dYK5nIOBzKIok
+eVXZ8xjcRnoBAumljZ3eGbTuysGDO95E56coDPE4IiAe4Esi7kl3fUS/NICoOGs
MC9tjeyMoscy+hoGsP57
=PL45
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner DT changes, take 2" from Maxime Ripard:
Only a single patch in here that fixes a DTC warning.
* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
In __ftrace_replace_code(), when converting the call to a nop in a function
it needs to compare against the "curr" (current) value of the ftrace ops, and
not the "new" one. It currently does not affect x86 which is the only arch
to do the trampolines with function graph tracer, but when other archs that do
depend on this code implement the function graph trampoline, it can crash.
Here's an example when ARM uses the trampolines (in the future):
------------[ cut here ]------------
WARNING: CPU: 0 PID: 9 at kernel/trace/ftrace.c:1716 ftrace_bug+0x17c/0x1f4()
Modules linked in: omap_rng rng_core ipv6
CPU: 0 PID: 9 Comm: migration/0 Not tainted 3.16.0-test-10959-gf0094b28f303-dirty #52
[<c02188f4>] (unwind_backtrace) from [<c021343c>] (show_stack+0x20/0x24)
[<c021343c>] (show_stack) from [<c095a674>] (dump_stack+0x78/0x94)
[<c095a674>] (dump_stack) from [<c02532a0>] (warn_slowpath_common+0x7c/0x9c)
[<c02532a0>] (warn_slowpath_common) from [<c02532ec>] (warn_slowpath_null+0x2c/0x34)
[<c02532ec>] (warn_slowpath_null) from [<c02cbac4>] (ftrace_bug+0x17c/0x1f4)
[<c02cbac4>] (ftrace_bug) from [<c02cc44c>] (ftrace_replace_code+0x80/0x9c)
[<c02cc44c>] (ftrace_replace_code) from [<c02cc658>] (ftrace_modify_all_code+0xb8/0x164)
[<c02cc658>] (ftrace_modify_all_code) from [<c02cc718>] (__ftrace_modify_code+0x14/0x1c)
[<c02cc718>] (__ftrace_modify_code) from [<c02c7244>] (multi_cpu_stop+0xf4/0x134)
[<c02c7244>] (multi_cpu_stop) from [<c02c6e90>] (cpu_stopper_thread+0x54/0x130)
[<c02c6e90>] (cpu_stopper_thread) from [<c0271cd4>] (smpboot_thread_fn+0x1ac/0x1bc)
[<c0271cd4>] (smpboot_thread_fn) from [<c026ddf0>] (kthread+0xe0/0xfc)
[<c026ddf0>] (kthread) from [<c020f318>] (ret_from_fork+0x14/0x20)
---[ end trace dc9ce72c5b617d8f ]---
[ 65.047264] ftrace failed to modify [<c0208580>] asm_do_IRQ+0x10/0x1c
[ 65.054070] actual: 85:1b:00:eb
Fixes: 7413af1fb7 "ftrace: Make get_ftrace_addr() and get_ftrace_addr_old() global"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The latest rewrite of ftrace removed the separate ftrace_ops of
the function tracer and the function graph tracer and had them
share the same ftrace_ops. This simplified the accounting by removing
the multiple layers of functions called, where the global_ops func
would call a special list that would iterate over the other ops that
were registered within it (like function and function graph), which
itself was registered to the ftrace ops list of all functions
currently active. If that sounds confusing, the code that implemented
it was also confusing and its removal is a good thing.
The problem with this change was that it assumed that the function
and function graph tracer can never be used at the same time.
This is mostly true, but there is an exception. That is when the
function profiler uses the function graph tracer to profile.
The function profiler can be activated the same time as the function
tracer, and this breaks the assumption and the result is that ftrace
will crash (it detects the error and shuts itself down, it does not
cause a kernel oops).
To solve this issue, a previous change allowed the hash tables
for the functions traced by a ftrace_ops to be a pointer and let
multiple ftrace_ops share the same hash. This allows the function
and function_graph tracer to have separate ftrace_ops, but still
share the hash, which is what is done.
Now the function and function graph tracers have separate ftrace_ops
again, and the function tracer can be run while the function_profile
is active.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If a SIGKILL is sent to a task waiting in __nfs_iocounter_wait,
it will busy-wait or soft lockup in its while loop.
nfs_wait_bit_killable won't sleep, and the loop won't exit on
the error return.
Stop the busy-wait by breaking out of the loop when
nfs_wait_bit_killable returns an error.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Commit 6094f83864
"nfs: allow coalescing of subpage requests" got rid of the requirement
that requests cover whole pages, but it made some incorrect assumptions.
It turns out that callers of this interface can map adjacent requests
(by file position as seen by req_offset + req->wb_bytes) to different pages,
even when they could share a page. An example is the direct I/O interface -
iov_iter_get_pages_alloc may return one segment with a partial page filled
and the next segment (which is adjacent in the file position) starts with a
new page.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Adjacent requests that share the same page are allowed, but should only
use one entry in the page vector. This avoids overruning the page
vector - it is sized based on how many bytes there are, not by
request count.
This fixes issues that manifest as "Redzone overwritten" bugs (the
vector overrun) and hangs waiting on page read / write, as it waits on
the same page more than once.
This also adds bounds checking to the page vector with a graceful failure
(WARN_ON_ONCE and pgio error returned to application).
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
This handles the 'nonblock=false' case in nfs_lock_and_join_requests.
If the group is already locked and blocking is allowed, drop the inode lock
and wait for the group lock to be cleared before trying it all again.
This should fix warnings found in peterz's tree (sched/wait branch), where
might_sleep() checks are added to wait.[ch].
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
This fixes handling of errors from nfs_page_group_lock in
nfs_lock_and_join_requests. It now releases the inode lock and the
reference to the head request.
Reported-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
__nfs_pageio_add_request was calling nfs_page_group_lock nonblocking, but
this can return -EAGAIN which would end up passing -EIO to the application.
There is no reason not to block in this path, so change the two calls to
do so. Also, there is no need to check the return value of
nfs_page_group_lock when nonblock=false, so remove the error handling code.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
nfs_page_group_lock was calling wait_on_bit_lock even when told not to
block. Fix by first trying test_and_set_bit, followed by wait_on_bit_lock
if and only if blocking is allowed. Return -EAGAIN if nonblocking and the
test_and_set of the bit was already locked.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Flip the meaning of the second argument from 'wait' to 'nonblock' to
match related functions. Update all five calls to reflect this change.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Just one bugfix for the PWM lookup table code that would cause a PWM
channel to be set to the wrong period and polarity for non-perfect
matches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SmTb
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fix from Thierry Reding:
"Just one bugfix for the PWM lookup table code that would cause a PWM
channel to be set to the wrong period and polarity for non-perfect
matches"
* tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Fix period and polarity in pwm_get() for non-perfect matches
The new_ctx pointer is set only for non-chanctx drivers. This yielded a
crash for chanctx-based drivers during channel switch finalization:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]
Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
