After any "soft gfx reset" we must manually invalidate the TLBs
associated with each ring. Empirically, it seems that a
suspend/resume or D3-D0 cycle count as a "soft reset". The symptom is
that the hardware would fail to note the new address for its status
page, and so it would continue to write the shadow registers and
breadcrumbs into the old physical address (now used by something
completely different, scary). Whereas the driver would read the new
status page and never see any progress, it would appear that the GPU
hung immediately upon resume.
Based on a patch by naresh kumar kachhi <naresh.kumar.kacchi@intel.com>
Reported-by: Thiago Macieira <thiago@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thiago Macieira <thiago@kde.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we get an error event really early in the driver setup sequence,
which gen3 is especially prone to with various display GTT faults we
Oops. So try to avoid this.
Additionally with Haswell the transcoders are a separate bank of
registers from the pipes (4 transcoders, 3 pipes). In event of an
error, we want to be sure we have a complete and accurate picture of
the machine state, so record all the transcoders in addition to all
the active pipes.
This regression has been introduced in
commit 702e7a56af
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Oct 23 18:29:59 2012 -0200
drm/i915: convert PIPECONF to use transcoder instead of pipe
Based on the patch "drm/i915: Dump all transcoder registers on error"
from Chris Wilson:
v2: Rebase so that we don't try to be clever and try to figure out the
cpu transcoder from hw state. That exercise should be done when we
analyze the error state offline.
The actual bugfix is to not call intel_pipe_to_cpu_transcoder in the
error state capture code in case the pipes aren't fully set up yet.
v3: Simplifiy the err->num_transcoders computation a bit. While at it
make the error capture stuff save on systems without a display block.
v4: Fix fail, spotted by Jani.
v5: Completely new commit message, cc: stable.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60021
Cc: stable@vger.kernel.org
Tested-by: Dustin King <daking@rescomp.stanford.edu>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
A few bugfixes for serious stuff and regressions. Highlight is the
reinstated hack to keep the i915 backlight on when running on an optimus
machine, this prevents black screens especially with some radeon muxed
platforms. And the patch to quiet dmesg on Linus' old mac mini ;-)
* tag 'drm-intel-fixes-2013-08-08' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: do not disable backlight on vgaswitcheroo switch off
drm/i915: Don't call encoder's get_config unless encoder is active
drm/i915: avoid brightness overflow when doing scale
drm/i915: update last_vblank when disabling the power well
drm/i915: fix gen4 digital port hotplug definitions
It takes an unsigned value. This happens not to blow up on 64-bit
architectures, but it does on 32-bit, causing
drm_calc_vbltimestamp_from_scanoutpos() to calculate totally bogus
timestamps for vblank events. Which in turn causes e.g. gnome-shell to
hang after a DPMS off cycle with current xf86-video-ati Git.
[airlied: regression introduced in drm: use monotonic time in drm_calc_vbltimestamp_from_scanoutpos]
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59339
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59836
Tested-by: shui yangwei <yangweix.shui@intel.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some more radeon fixes. Mostly dpm and uvd fixes. Fixes hangs
with dpm on more rv6xx asics, and fixes suspend and resume with UVD.
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make missing smc ucode non-fatal
drm/radeon/dpm: require rlc for dpm
drm/radeon/cik: use a mutex to properly lock srbm instanced registers
drm/radeon: remove unnecessary unpin
drm/radeon: add more UVD CS checking
drm/radeon: stop sending invalid UVD destroy msg
drm/radeon: only save UVD bo when we have open handles
drm/radeon: always program the MC on startup
drm/radeon: fix audio dto calculation on DCE3+ (v3)
drm/radeon/dpm: disable sclk ss on rv6xx
drm/radeon: fix halting UVD
drm/radeon/dpm: adjust power state properly for UVD on SI
drm/radeon/dpm: fix spread spectrum setup (v2)
drm/radeon/dpm: adjust thermal protection requirements
drm/radeon: select audio dto based on encoder id for DCE3
drm/radeon: properly handle pm on gpu reset
The smc ucode is required for dpm (dynamic power
management), but if it's missing just skip dpm setup
and don't disable acceleration.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=67876
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The rlc is required for dpm to work properly, so if
the rlc ucode is missing, don't enable dpm. Enabling
dpm without the rlc enabled can result in hangs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't pin the BO on allocation, so don't unpin it on free.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Improve error handling in case userspace sends us
an invalid command buffer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We also need to check the handle.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise just reinitialize from scratch on resume,
and so make it more likely to succeed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For r6xx+ asics. This mirrors the behavior of pre-r6xx
asics. We need to program the MC even if something
else in startup() fails. Failure to do so results in
an unusable GPU.
Based on a fix from: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to set the wallclock ratio and adjust the phase
and module registers appropriately. May fix problems
with audio timing at certain display timings.
v2: properly handle clocks below 24mhz
v3: rebase r600 changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.
Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are some hardware issue with reclocking on SI when
UVD is active, so use a stable power state when UVD is
active. Fixes possible hangs and performance issues when
using UVD on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check for engine and memory clock ss separately
and only enable dynamic ss if either of them are found.
This should fix systems which have a ss table, but do
not have entries for engine or memory. On those systems
we may enable dynamic spread spectrum without enabling
it on the engine or memory clocks which can lead to a
hang in some cases.
fixes some systems reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
v2: fix typo
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On rv770 and newer, clock gating is not required
for thermal protection. The only requirement is that
the design utilizes a thermal sensor.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two audio dtos on radeon asics that you can
select between. Normally, dto0 is used for hdmi and
dto1 for DP, but it seems that the dto is somehow
tied to the encoders on DCE3 asics.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=67435
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When we reset the GPU, we need to properly tear
down power management before reseting the GPU and then
set it back up again after reset. Add the missing
radeon_pm_[suspend|resume] calls to the gpu reset
function.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On muxed systems, the other vgaswitcheroo client may depend on i915 to
handle the backlight. We began switching off the backlight since
commit a261b246eb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 26 19:21:47 2012 +0200
drm/i915: disable all crtcs at suspend time
breaking backlight on discreet graphics in (some) muxed systems.
Keep the backlight on when the state is changed through vgaswitcheroo.
Note: The alternative would be to add a quirk table to achieve the same
based on system identifiers, but AFAICS it would asymptotically approach
effectively the same as this patch as more IDs are added, but with the
maintenance burden of the quirk table.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55311
Tested-by: Fede <fedevx@yahoo.com>
Tested-by: Aximab <laurent.debian@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59785
Tested-by: sfievet <sebastien.fievet@free.fr>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The SDVO code tries to compare the encoder's and crtc's idea of the
pixel_multiplier. Normally they have to match, but when transitioning
to DPMS off, we turn off the pipe before reading out the pipe_config,
so the pixel_multiplier in the pipe_config will be 0, whereas the
encoder will still have its pixel_multiplier set to whatever value we
were using when the display was active. This leads to a warning
from intel_modeset_check_state().
WARNING: CPU: 1 PID: 2846 at drivers/gpu/drm/i915/intel_sdvo.c:1378 intel_sdvo_get_config+0x158/0x160()
SDVO pixel multiplier mismatch, port: 0, encoder: 1
Modules linked in: snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_hwdep
CPU: 1 PID: 2846 Comm: Xorg Not tainted 3.11.0-rc3-00208-gbe1e8d7-dirty #19
Hardware name: Apple Computer, Inc. Macmini1,1/Mac-F4208EC8, BIOS MM11.88Z.0055.B03.0604071521 04/07/06
00000000 00000000 ef0afa54 c1597bbb c1737ea4 ef0afa84 c10392ca c1737e6c
ef0afab0 00000b1e c1737ea4 00000562 c12dfbe8 c12dfbe8 ef0afb14 00000000
f697ec00 ef0afa9c c103936e 00000009 ef0afa94 c1737e6c ef0afab0 ef0afadc
Call Trace:
[<c1597bbb>] dump_stack+0x41/0x56
[<c10392ca>] warn_slowpath_common+0x7a/0xa0
[<c103936e>] warn_slowpath_fmt+0x2e/0x30
[<c12dfbe8>] intel_sdvo_get_config+0x158/0x160
[<c12c3220>] check_crtc_state+0x1e0/0xb10
[<c12cdc7d>] intel_modeset_check_state+0x29d/0x7c0
[<c12dfe5c>] intel_sdvo_dpms+0x5c/0xa0
[<c12985de>] drm_mode_obj_set_property_ioctl+0x40e/0x420
[<c1298625>] drm_mode_connector_property_set_ioctl+0x35/0x40
[<c1289294>] drm_ioctl+0x3e4/0x540
[<c10fc1a2>] do_vfs_ioctl+0x72/0x570
[<c10fc72f>] SyS_ioctl+0x8f/0xa0
[<c159b7fa>] sysenter_do_call+0x12/0x22
---[ end trace 7ce940aff1366d60 ]---
Fix the problem by skipping the encoder get_config() function for
inactive encoders.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some card's max brightness level is pretty large, e.g. on Acer Aspire
4732Z, the max level is 989910. If user space set a large enough level
then the current scale done in intel_panel_set_backlight will cause an
integer overflow and the scaled level will be mistakenly small, leaving
user with an almost black screen. This patch fixes this problem.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
[danvet: Add a comment to explain what's going on.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DRM layer keeps track of our vblanks and it assumes our vblank
counters only go back to zero when they overflow. The problem is that
when we disable the power well our counters also go to zero, but it
doesn't mean they did overflow. So on this patch we grab the lock and
update last_vblank so the DRM layer won't think our counters
overflowed.
This patch fixes the following intel-gpu-tools test:
./kms_flip --run-subtest blocking-absolute-wf_vblank
Regression introduced by the following commit:
commit bf51d5e2cd
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Wed Jul 3 17:12:13 2013 -0300
drm/i915: switch disable_power_well default value to 1
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66808
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Added a comment that this might be better done in
drm_vblank_post_modeset in general.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently Bspec is wrong in this case here even for gm45. Note that
Bspec is horribly misguided on i965g/gm, so we don't have any other
data points besides that it seems to make machines work better.
With this changes all the bits in PORT_HOTPLUG_STAT for the digital
ports are ordered the same way. This seems to agree with what register
dumps from the hpd storm handling code shows, where the LIVE bit and
the short/long pulse STATUS bits light up at the same time with this
enumeration (but no with the one from Bspec).
Also tested on my gm45 which has two DP+ ports, and everything seems
to still work as expected.
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg23054.html
Cc: Egbert Eich <eich@suse.com>
Cc: Jan Niggemann <jn@hz6.de>
Tested-by: Jan Niggemann <jn@hz6.de>
[danvet: Add a big warning that Bspec seems to be wrong for these
bits, suggested by Jani.]
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When a BO gets pinned the placement may get changed. If the memory is
mapped into user space and user space has already accessed the mapped
range the page tables are set up but now point to the wrong memory.
Set bo.mdev->dev_mapping in mgag200_bo_create() to make sure that
ttm_bo_unmap_virtual() called from ttm_bo_handle_move_mem() will take
care of this.
v2: Don't call ttm_bo_unmap_virtual() in mgag200_bo_pin(), fix comment.
Signed-off-by: Egbert Eich <eich@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a cirrus version of Egbert Eich's patch for mgag200.
Without bo.bdev->dev_mapping set, the ttm_bo_unmap_virtual_locked
called from ttm_bo_handle_move_mem returns with no effect. If any
application accessed the memory before it was moved, it will
access wrong memory next time. This causes crashes when changing
resolution down.
Signed-off-by: Michal Srb <msrb@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Upon some code refactoring, a hunk was missed. This was fixed for
next, but missed the current trees, and hasn't yet been merged by Dave
Airlie. It is fixed in:
commit 907b28c56e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:52 2013 +0100
drm/i915: Colocate all GT access routines in the same file
It is introduced by:
commit 181d1b9e31
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 13:16:24 2013 +0200
drm/i915: fix up gt init sequence fallout
Reported-by: Dave Jones <davej@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
- more fixes for SI dpm
- fix DP on some rv6xx boards
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: re-enable cac control on SI
drm/radeon/dpm: fix calculations in si_calculate_leakage_for_v_and_t_formula
drm: fix 64 bit drm fixed point helpers
drm/radeon/atom: initialize more atom interpretor elements to 0
The ProcessAuxChannel table on some rv635 boards assumes
the divmul members are initialized to 0 otherwise we get
an invalid fb offset since it has a bad mask set when
setting the fb base. While here initialize all the
atom interpretor elements to 0.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60639
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
nouveau fixes a number of regressions and a few user triggerable oops
since -rc1. Along with a few mpeg engine fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: fix semaphore dmabuf obj
drm/nouveau/vm: make vm refcount into a kref
drm/nv31/mpeg: don't recognize nv3x cards as having nv44 graph class
drm/nv40/mpeg: write magic value to channel object to make it work
drm/nouveau: fix size check for cards without vm
drm/nv50-/disp: remove dcb_outp_match call, and related variables
drm/nva3-/disp: fix hda eld writing, needs to be padded
drm/nv31/mpeg: fix mpeg engine initialization
drm/nv50/mc: include vp in the fb error reporting mask
drm/nouveau: fix null pointer dereference in poll_changed
drm/nv50/gpio: post-nv92 cards have 32 interrupt lines
drm/nvc0/fb: take lock in nvc0_ram_put()
drm/nouveau/core: xtensa firmware size needs to be 0x40000 no matter what
Never used to be required, but a recent change made it necessary.
Reported-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This pull request fixes module build and g2d clock
control issues, and includes related cleanup.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Remove module.h header inclusion
drm/exynos: consider common clock framework to g2d driver.
drm/exynos: fix module build error
drm/exynos: exynos_drm_ipp: fix return value check
Looks like the rewrite in commit ebb945a94b ("drm/nouveau: port all
engines to new engine module format") missed that one little detail.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Unused and irrelavant since the code move of DP training/linkcontrol interrupt
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commits 0a9e2b959 (drm/nvd0/disp: move HDA codec setup to core) and
a4feaf4ea (drm/nva3/disp: move hda codec handling to core) moved code
around but neglected to fill data up to 0x60 as before. This caused
/proc/asound/cardN/eld#3.0 to show eld_valid as 0. With this patch, that
file is again populated with the correct data.
See https://bugs.freedesktop.org/show_bug.cgi?id=67051
Reported-and-tested-by: Alex <alupu01@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
object->engine is null, which leads to a null deref down the line
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes vgaswitcheroo on a card without display.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since the original merge of nouveau to upstream kernel, we were assuming
that nv90 (and later) cards have 32 lines.
Based on mmio traces of the binary driver, as well as PBUS error messages
during read/write of the e070/e074 registers, we can conclude that nv92
has only 16 lines whereas nv94 (and later) cards have 32.
Reported-and-tested-by: David M. Lloyd <david.lloyd@redhat.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Kernel panic caused by list corruption in ltcg seems to indicate a
concurrency issue.
Take mutex of pfb like nv50_ram_put() to eliminate concurrency.
V2: Separate critical section into separate function, avoid taking the
lock twice on NVC0
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The current logic is wrong since we send fw->size >> 8 to the
card. Rounding the size up by 0x100 and 0x1000 didn't seem to help,
the card still hung, so go back to what the blob does -- 0x40000.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
