This makes it a bit more obvious in genirq diagnostics that they
aren't handled by the i.MX interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
They will be automatically powered off at startup so users will
need to enable them for use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
otg_ulpi_create is defined in drivers/usb/otg/ulpi.c which depends on
CONFIG_USB_ULPI. So protect its usage by the same symbol. Moreover
mxc_ulpi_access_ops needs CONFIG_MXC_ULPI.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 52939c03 (ARM: MX3: fix CPU revision number detection) started
using the CPU's SREV register for revision number detection. This
makes it mandatory to have a valid SPBA0 mapping. Add this to the
global map_io code instead of adding multiple copies for each board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested on Qong (EVB-Lite)
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Check whether L2 is present or not in XSC3. If it's present, enable L2
immediately.
Disabling L2 after L2 is enabled that would result in unpredicatable behavior
of XSC3 processor.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Outer cache checked whether L2 is enabled or not. If L2 isn't enabled in XSC3,
it would enable L2. This operation is evil that would make system hang.
In XSC3 core document, these words are mentioned in below.
"Following reset, the L2 Unified Cache Enable bit is cleared. To enable the L2
Cache, software may set the bit to a '1' before or at the same time as enabling
the MMU. Enabling the L2 Cache after the MMU has been enabled or disabling the
L2 Cache after the L2 Cache has been enabled, may result in unpredictable
behavior of the processor."
When outer cache is initialized, the MMU is already enabled. We couldn't enable
L2 after MMU enabled.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ARRAY_AND_SIZE is already defined arch/arm/mach-mmp/common.h which is
already included.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Bin Yang <bin.yang@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
DM9000s on Zeus sometime fail under heavy load.
Relaxing the timings a bit seems to be of a great help.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This has to be selected, otherwise some peripherals don't get initialized.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Use resource_size for {request/release}_mem_region and ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The PCIe inbound window size is supposed to be a power of two. If
the total amount of RAM installed in the system is not a power of two,
round it up such that it is.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This fixes a "start_kernel(): bug: interrupts were enabled early".
rtc_cmos now takes care of initializing the ISA RTC and reading the
current time and date from it; there's no need to repeat that here,
thereby causing interrupts to be enabled too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PAGE_KERNEL should not be executable; any area marked executable can
be prefetched into the instruction cache. We don't want vmalloc areas
to be read in this way.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two bugs in s3c_nand_set_platdata() where thet device's platform
data was not set, and the wrong error check was being performed on
the return of s3c_nand_copy_set().
Fixes the following OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000004
PC is at s3c24xx_nand_probe+0x234/0x594
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It is unpredictable to have the same memory mapped using different
shared bit settings for ARMv6 and ARMv7 CPUs. Fix this for the CPU
write buffer bug test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definition for the touchscreen driver platform data and initial
support for the H1940 machine.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the NAND_SCAN_SILENT_NODEV to the optional NAND devices that may not
be fitted to the board
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the NAND_SCAN_SILENT_NODEV to the optional NAND devices that may not
be fitted to the board
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit f74f7e57ae (ARM: use
flush_kernel_dcache_area() for dmabounce) has broken dmabounce build:
CC arch/arm/common/dmabounce.o
arch/arm/common/dmabounce.c: In function 'unmap_single':
arch/arm/common/dmabounce.c:315: error: implicit declaration of function '__cpuc_flush_kernel_dcache_area'
make[2]: *** [arch/arm/common/dmabounce.o] Error 1
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix bug of uart0 platfrom data for nuc900
Signed-off-by: lijie <eltshanli@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
putc support for nuc900
Signed-off-by: lijie <eltshanli@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix compiling error for NUC900
Signed-off-by: lijie <eltshanli@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Oprofile ARMv7 the PMNC_D bit was set to lower the PMU IRQs
and so to decrease the risk of errata #628216 from appearing.
The effect of setting the PMNC_D bit is that the CCNT counter
is divided by 64, making the program counter events count
inaccurate.
The new OMAP3 r4 cores should have that errata fixed.
The PMNC_D bit should not be set, this patch fixes it.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
26-bit ARM support was removed a long time ago, and this symbol has
been defined to be 'y' ever since. As it's never disabled anymore,
we can kill it without any side effects.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This avoids races in the VFP code where the dead thread may have
state on another CPU. By moving this code to exit_thread(), we
will be running as the thread, and therefore be running on the
current CPU.
This means that we can ensure that the only local state is accessed
in the thread notifiers.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 2c9b9c849 added an argument to __cpuc_flush_dcache_page
and renamed it.
Update a caller of the old function to fix this build error:
CC arch/arm/mm/copypage-v6.o
arch/arm/mm/copypage-v6.c: In function 'v6_copy_user_highpage_nonaliasing':
arch/arm/mm/copypage-v6.c:51: error: implicit declaration of function '__cpuc_flush_dcache_page'
make[1]: *** [arch/arm/mm/copypage-v6.o] Error 1
make: *** [arch/arm/mm] Error 2
Reported-by: Jinsung Yang <jsgood.yang@samsung.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: serial - fix bug introduced in
mfd: twl: fix twl4030 rename for remaining driver, board files
USB ehci: replace mach header with plat
omap3: Allow EHCI to be built on OMAP3
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi: spi_txx9.c: use resource_size()
spi: spi_sh_sci.c: use resource_size()
spi: spi_mpc8xxx.c: use resource_size()
spi: spi_bfin5xx.c: use resource_size()
spi: atmel_spi.c: use resource_size()
spi: Add s3c64xx SPI Controller driver
atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
spi_s3c24xx: add FIQ pseudo-DMA support
spi: controller driver for Designware SPI core
spidev: add proper section markers
spidev: use DECLARE_BITMAP instead of declaring the array
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
PCMCIA: fix pxa2xx_lubbock modular build error
[ARM] Update mach-types
[ARM] pxa: fix no reference of cpu_is_pxa25x() in devices.c
[ARM] pxa/cm-x300: add PWM backlight support
revert "[ARM] pxa/cm-x300: add PWM backlight support"
ARM: use flush_kernel_dcache_area() for dmabounce
ARM: add size argument to __cpuc_flush_dcache_page
ARM: 5848/1: kill flush_ioremap_region()
ARM: cache-l2x0: make better use of background cache handling
ARM: cache-l2x0: avoid taking spinlock for every iteration
[ARM] Kirkwood: Add LaCie Network Space v2 support
ARM: dove: fix the mm mmu flags of the pj4 procinfo
Add pseudo-DMA by FIQ to the S3C24XX SPI driver. This allows the driver
to get DMA-like performance where there are either no free DMA channels or
when doing transfers that required both TX and RX data paths.
Since this patch requires the addition of an assembly file to hold the FIQ
code, we rename the module (instead of adding a rename of the .c file to
this patch). We expect most users are loading this via udev and thus
there should be no change to the userland configuration.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
Commit f62349ee97 had side effect that
causes kernel to oops when we are suspending to ram:
# echo mem > /sys/power/state
WARNING: at kernel/irq/manage.c:858 __free_irq+0x90/0x174()
Trying to free already-free IRQ 72
Modules linked in:
Backtrace:
[<c00328d0>] (dump_backtrace+0x0/0x110) from [<c0347298>] (dump_stack+0x18/0x1c)
r7:dfd4be08 r6:c009505c r5:c03fbfd1 r4:0000035a
[<c0347280>] (dump_stack+0x0/0x1c) from [<c005a408>] (warn_slowpath_common+0x50/0x68)
[<c005a3b8>] (warn_slowpath_common+0x0/0x68) from [<c005a46c>] (warn_slowpath_fmt+0x30)
r7:c0474afc r6:00000048 r5:00000000 r4:c0474ac0
[<c005a43c>] (warn_slowpath_fmt+0x0/0x38) from [<c009505c>] (__free_irq+0x90/0x174)
r3:00000048 r2:c03fc0ef
[<c0094fcc>] (__free_irq+0x0/0x174) from [<c0095184>] (free_irq+0x44/0x64)
[<c0095140>] (free_irq+0x0/0x64) from [<c0038100>] (omap_uart_enable_irqs+0x4c/0x90)
r7:c034d58c r6:00000003 r5:00000000 r4:c0463028
[<c00380b4>] (omap_uart_enable_irqs+0x0/0x90) from [<c003d8f8>] (omap3_pm_begin+0x1c/0)
r5:00000003 r4:00000000
[<c003d8dc>] (omap3_pm_begin+0x0/0x28) from [<c008d008>] (suspend_devices_and_enter+0x)
[<c008cfd8>] (suspend_devices_and_enter+0x0/0x1dc) from [<c008d29c>] (enter_state+0xe8)
r5:c03f7f46 r4:00000000
[<c008d1b4>] (enter_state+0x0/0x140) from [<c008c8e0>] (state_store+0x9c/0xc4)
r7:c034d58c r6:00000003 r5:00000003 r4:c03f7f46
[<c008c844>] (state_store+0x0/0xc4) from [<c01cb2dc>] (kobj_attr_store+0x20/0x24)
[<c01cb2bc>] (kobj_attr_store+0x0/0x24) from [<c0119420>] (sysfs_write_file+0x114/0x14)
[<c011930c>] (sysfs_write_file+0x0/0x148) from [<c00cb298>] (vfs_write+0xb8/0x164)
[<c00cb1e0>] (vfs_write+0x0/0x164) from [<c00cb408>] (sys_write+0x44/0x70)
r8:4001f000 r7:00000004 r6:df81bd00 r5:00000000 r4:00000000
[<c00cb3c4>] (sys_write+0x0/0x70) from [<c002f040>] (ret_fast_syscall+0x0/0x38)
r8:c002f204 r7:00000004 r6:401fa5e8 r5:4001f000 r4:00000004
This is due the fact that uart_list list was populated in
omap_serial_early_init() and omap_uart_enable_irqs() went through this
list even when serial idle wasn't enabled for all uarts.
This patch moves the code that populates the uart_list and enables uart
clocks into omap_serial_init_port().
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'module' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
modpost: fix segfault with short symbol names
module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y
Kbuild: clear marker out of modpost
module: make MODULE_SYMBOL_PREFIX into a CONFIG option
ARM: unexport symbols used to implement floating point emulation
ARM: use unified discard definition in linker script
x86: don't export inline function
sparc64: don't export static inline pci_ functions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
Input: ALPS - add interleaved protocol support (Dell E6x00 series)
Input: keyboard - don't override beep with a bell
Input: altera_ps2 - fix test of unsigned in altera_ps2_probe()
Input: add mc13783 touchscreen driver
Input: ep93xx_keypad - update driver to new core support
Input: wacom - separate pen from express keys on Graphire
Input: wacom - add defines for data packet report IDs
Input: wacom - add support for new LCD tablets
Input: wacom - add defines for packet lengths of various devices
Input: wacom - ensure the device is initialized properly upon resume
Input: at32psif - do not sleep in atomic context
Input: i8042 - add Gigabyte M1022M to the noloop list
Input: i8042 - allow installing platform filters for incoming data
Input: i8042 - fix locking in interrupt routine
Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad
Input: document use of input_event() function
Input: sa1111ps2 - annotate probe() and remove() methods
Input: ambakmi - annotate probe() and remove() methods
Input: gscps2 - fix probe() and remove() annotations
Input: altera_ps2 - add annotations to probe and remove methods
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
ppc440spe-adma: adds updated ppc440spe adma driver
iop-adma.c: use resource_size()
dmaengine: clarify the meaning of the DMA_CTRL_ACK flag
sh: stylistic improvements for the DMA driver
dmaengine: fix dmatest to verify minimum transfer length and test buffer size
sh: DMA driver has to specify its alignment requirements
Add COH 901 318 DMA block driver v5
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
Currently all architectures but microblaze unconditionally define
USE_ELF_CORE_DUMP. The microblaze omission seems like an error to me, so
let's kill this ifdef and make sure we are the same everywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Simek <michal.simek@petalogix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the platform specific callback to control LCD panel and backlight
power.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
OMAP34XX has EHCI, so select USB_ARCH_HAS_EHCI.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
clockevents: Convert to raw_spinlock
clockevents: Make tick_device_lock static
debugobjects: Convert to raw_spinlocks
perf_event: Convert to raw_spinlock
hrtimers: Convert to raw_spinlocks
genirq: Convert irq_desc.lock to raw_spinlock
smp: Convert smplocks to raw_spinlocks
rtmutes: Convert rtmutex.lock to raw_spinlock
sched: Convert pi_lock to raw_spinlock
sched: Convert cpupri lock to raw_spinlock
sched: Convert rt_runtime_lock to raw_spinlock
sched: Convert rq->lock to raw_spinlock
plist: Make plist debugging raw_spinlock aware
bkl: Fixup core_lock fallout
locking: Cleanup the name space completely
locking: Further name space cleanups
alpha: Fix fallout from locking changes
locking: Implement new raw_spinlock
locking: Convert raw_rwlock functions to arch_rwlock
locking: Convert raw_rwlock to arch_rwlock
...
* git://git.infradead.org/battery-2.6:
power_supply_sysfs: Handle -ENODATA in a special way
wm831x_backup: Remove unused variables
gta02: Set pcf50633 charger_reference_current_ma
pcf50633: Query charger status directly
pcf50633: Properly reenable charging when the supply conditions change
pcf50633: Get rid of charging restart software auto-triggering
pcf50633: introduces battery charging current control
pcf50633: Add ac power supply class to the charger
wm831x: Factor out WM831x backup battery charger
This driver was merged before the ep93xx core support was added
for the keypad clock and acquiring/releasing the necessary gpio's.
Now that the proper support is in the ep93xx core this driver
needs to be updated to work correctly.
Summary of changes:
1) Remove some unused members from the platform data.
2) Remove the custom KEY macro and use the ones available in
<linux/input/matrix_keypad.h>
3) Remove the keypad_{readl/writel} macros and just use
__raw_{readl/writel} directly.
4) Update the clk_set_rate() call to work with the core support.
5) Cleanup the probe routine and remove some unneeded messages.
6) Use the ep93xx core functions to acquire and release the gpio's.
7) Fix the clk_get() call to get the keypad clock.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information. In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).
This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Kconfigs for in-tree floating point emulation do not allow building
as modules. That leaves the Acorn FPEmulator module. I found two public
releases of this as a binary module for 2.1 and 2.2 kernels, optimized
for ARMV4.[1] If there is a resurgence of interest in this, the symbols
can always be re-exported.
This allows the EXPORT_SYMBOL_ALIAS() hack to be removed. The ulterior
motive here is that EXPORT_SYMBOL_ALIAS() makes it harder to sort the
resulting kernel symbol tables. Sorted symbol tables will allow faster
symbol resolution during module loading.
Note that fp_send_sigs() and fp_printk() are simply aliases for existing
exports and add no obvious value. Similarly fp_enter could easily be
renamed to kern_fp_enter at the point of definition. Therefore removing
EXPORT_SYMBOL_ALIAS will not serve as a material obstacle to re-adding
the exports should they be desired in future.
Build tested only.
[1] http://ftp.arm.linux.org.uk/pub/linux/arm/fpemulator/
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Commit 023bf6f "linker script: unify usage of discard definition"
changed the linker scripts for all architectures except for ARM.
I can find no discussion about this ommision, so here are the changes
for ARM.
These changes are exactly parallel to the ia64 case.
"ia64 is notable because it first throws away some ia64 specific
subsections and then include the rest of the sections into the final
image, so those sections must be discarded before the inclusion."
Not boot-tested. In build testing, the modified linker script generated
an identical vmlinux file.
[I would like to be able to rely on this unified discard definition.
I want to sort the kernel symbol tables to allow faster symbol
resolution during module loading. The simplest way appears to be
to generate sorted versions from vmlinux.o, link them in to vmlinux,
_and discard the original unsorted tables_.
This work is driven by my x86 netbook, but it is implemented at a
generic level. It is possible it will benefit some ARM systems also.]
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by-without-testing: Tejun Heo <tj@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Name space cleanup for rwlock functions. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Not strictly necessary for -rt as -rt does not have non sleeping
rwlocks, but it's odd to not have a consistent naming convention.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Name space cleanup. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Further name space cleanup. No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
The raw_spin* namespace was taken by lockdep for the architecture
specific implementations. raw_spin_* would be the ideal name space for
the spinlocks which are not converted to sleeping locks in preempt-rt.
Linus suggested to convert the raw_ to arch_ locks and cleanup the
name space instead of using an artifical name like core_spin,
atomic_spin or whatever
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
spi: fix probe/remove section markings
Add OMAP spi100k driver
spi-imx: don't access struct device directly but use dev_get_platdata
spi-imx: Add mx25 support
spi-imx: use positive logic to distinguish cpu variants
spi-imx: correct check for platform_get_irq failing
ARM: NUC900: Add spi driver support for nuc900
spi: SuperH MSIOF SPI Master driver V2
spi: fix spidev compilation failure when VERBOSE is defined
spi/au1550_spi: fix setupxfer not to override cfg with zeros
spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove
spi/i.MX: fix broken error handling for gpio_request
spi/i.mx: drain MXC SPI transfer buffer when probing device
MAINTAINERS: add SPI co-maintainer.
spi/xilinx_spi: fix incorrect casting
spi/mpc52xx-spi: minor cleanups
xilinx_spi: add a platform driver using the xilinx_spi common module.
xilinx_spi: add support for the DS570 IP.
xilinx_spi: Switch to iomem functions and support little endian.
xilinx_spi: Split into of driver and generic part.
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (58 commits)
mfd: Add twl6030 regulator subdevices
regulator: Add support for twl6030 regulators
rtc: Add twl6030 RTC support
mfd: Add support for twl6030 irq framework
mfd: Rename twl4030_ routines in twl-regulator.c
mfd: Rename twl4030_ routines in rtc-twl.c
mfd: Rename all twl4030_i2c*
mfd: Rename twl4030* driver files to enable re-use
mfd: Clarify twl4030 return value for read and write
mfd: Add all twl4030 regulators to the twl4030 mfd driver
mfd: Don't set mc13783 ADREFMODE for touch conversions
mfd: Remove ezx-pcap defines for custom led gpio encoding
mfd: Near complete mc13783 rewrite
mfd: Remove build time warning for WM835x register default tables
mfd: Force I2C to be built in when building WM831x
mfd: Don't allow wm831x to be built as a module
mfd: Fix incorrect error check for wm8350-core
mfd: Fix twl4030 warning
gpiolib: Implement gpio_to_irq() for wm831x
mfd: Remove default selection of AB4500
...
After copying data from the bounce buffer to the real buffer, use
flush_kernel_dcache_page() to ensure that data is written back in
manner coherent with future userspace mappings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is not enough users to warrant its existence, and it is actually
an obstacle to progress with the new DMA API which cannot cover this
case properly.
To keep backward compatibility, let's perform the necessary custom
cache maintenance locally in the only driver affected.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point having the hardware support background operations
if we issue a cache operation, and then wait for it to complete
before calculating the address of the next operation. We gain no
advantage in the cache controller stalling the bus until completion.
What we should be doing is using the 'wait' time productively by
calculating the address of the next operation, and only then waiting
for the previous operation to complete. This means that cache
operations can occur in parallel with the CPU calculating the next
address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Taking the spinlock for every iteration is very expensive; instead,
batch iterations up into 4K blocks, releasing and reacquiring the
spinlock between each block.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No idea if this platform actually uses cpufreq_get(), but it doesn't
have any cpufreq drivers. That's not to say it doesn't use cpufreq_get()
in its drivers. LH7a40x is unmaintained anyhow, and should probably
be killed off.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-sa1100/generic.c:117: error: redefinition of 'cpufreq_get'
include/linux/cpufreq.h:299: error: previous definition of 'cpufreq_get' was here
cpufreq_get() is used on these platforms to tell drivers what the CPU
frequency is, and therefore the bus frequency - which is critical for
setting the PCMCIA and LCD timings. Adding ifdefs to these drivers to
select cpufreq_get() or some other interface adds confusion. Making
these drivers use some other interface for the normal paths and cpufreq
stuff for the cpufreq notifier is insane as well.
(Why x86 can't provide a version of cpufreq_get() which returns the
CPU frequency when CPUFREQ is disabled is beyond me, rather than
requiring a dummy zero-returning cpufreq_get(). Especially as they
do:
unsigned long khz = cpufreq_get(cpu);
if (!khz)
khz = tsc_khz;
In other words, if CPUFREQ is disabled, get it from tsc_khz - why
not provide a dummy cpufreq_get() which returns tsc_khz?)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The power scripts optimisation was mainly done by:
Tero Kristo <tero.kristo@nokia.com> and
Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
I'm only refactoring and testing it against the mainline kernel.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: linux-omap@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Anders Grafström reports that footbridge fails to build after 1c4a4f4.
Fix this by adding the necessary definitions for __pfn_to_bus and
__bus_to_pfn.
Reported-by: Anders Grafström <anders.grafstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the VFP notifier is called for flush_thread(), we may be
preemptible, meaning we might migrate to another CPU, which means
referencing the current CPU number without some form of locking is
invalid, and can cause data corruption.
For the most cases, this isn't a problem since atomic notifiers are run
under rcu lock, which for most configurations results in preemption
being disabled - except when the preemptable tree-based rcu
implementation is selected.
Let's make it safe anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Arcom Zeus CF slot requires the same kind of support as the Viper.
To avoid code duplication, introduce a platform device that abstracts
the differences.
This also allows for the removal of the ugly export of viper_cf_rst().
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
IXP4xx: GTWX5715 platform only has two PCI IRQ lines, not four.
IXP4xx: Introduce IXP4XX_GPIO_IRQ(n) macro and convert IXP4xx platform files.
IXP4xx: move Gemtek GTWX5715 platform macros to the platform code.
IXP4xx: Remove unused Motorola PrPMC1100 platform macros.
IXP4xx: move FSG platform macros to the platform code.
IXP4xx: move DSM G600 platform macros to the platform code.
IXP4xx: move NAS100D platform macros to the platform code.
IXP4xx: move NSLU2 platform macros to the platform code.
IXP4xx: move Coyote platform macros to the platform code.
IXP4xx: move AVILA platform macros to the platform code.
IXP4xx: move IXDP425 platform macros to the platform code.
IXP4xx: Extend PCI MMIO indirect address space to 1 GB.
IXP4xx: Fix compilation failure with CONFIG_IXP4XX_INDIRECT_PCI.
IXP4xx: Drop "__ixp4xx_" prefix from in/out/ioread/iowrite functions for clarity.
IXP4xx: Rename indirect MMIO primitives from __ixp4xx_* to __indirect_*.
IXP4xx: Ensure index is positive in irq_to_gpio() and npe_request().
ARM: fix insl() and outsl() endianness on IXP4xx architecture.
IXP4xx: Fix normally-disabled debugging text in drivers/net/arm/ixp4xx_eth.c.
IXP4xx: change the timer base frequency to 66.666000 MHz.
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (75 commits)
omap3: Fix OMAP35XX_REV macros
omap: serial: fix non-empty uart fifo read abort
omap3: Zoom2/3: Update hsmmc board config params
omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards
omap3: id code detection 3525 vs 3515
omap3: rx51: Use wl1251 in SPI mode 3
omap3: zoom2/3: make MMC slot work again
omap1: htcherald: Update defconfig to include mux support
omap1: LCD_DMA: Use some define rather than a hexadecimal
omap: header: remove unused data-type
omap: arch/arm/plat-omap/devices.c - sort alphabetically
omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND
OMAP3: serial - allow platforms specify which UARTs to initialize
omap3: cm-t35: add mux initialization
OMAP4: Sync up omap4430 defconfig
OMAP4: Remove the secondary wait loop
OMAP4: AuxCoreBoot registers only accessible in secure mode
OMAP4: Fix SRAM base and size
OMAP4: Fix cpu detection
omap3: pandora: board file updates for .33
...
Simplified arch/arm/Makefile by dropping the maketools target
It was undocumented and not needed
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The simplest method was to add an extra asm-offsets.h
file in arch/$ARCH/include/asm that references the generated file.
We can now migrate the architectures one-by-one to reference
the generated file direct - and when done we can delete the
temporary arch/$ARCH/include/asm/asm-offsets.h file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
In original implementation, the revision passed to
these macros contained revision number in lower nibble.
But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.
This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: Sanjeev Premi <premi@ti.com>
OMAP3xxx and OMAP4430 UART IP blocks have a restriction wrt RX FIFO.
Empty RX fifo read causes an abort.
OMAP3xxx:
UART IP revision >= 0x52 have this issue
MVR register format is:
Bits Field Name Description Type Reset
31:8 RESERVED RO 0x0
7:4 MAJOR Major revision number of the module. RO 0x--
3:0 MINOR Minor revision number of the module. RO 0x--
OMAP4xxx:
All revisions have this issue
Revision id check is not used as the format of MVR resigster has changed
For omap4 MVR register reads as: 0x50410602 => Revision id = 0x0602
Format of MVR register on omap4 is: (Courtesy: Cousson, Benoit)
Bits Field Name Description Type Reset
31:30 SCHEME Scheme revision number of module RO 0x1
29:28 RESERVED RO 0x1
27:16 FUNC Function revision number of module RO 0x041
15:11 RTL Rtl revision number of module RO 0x00
10:8 MAJOR Major revision number of the module. RO 0x6
7:6 CUSTOM Custom revision number of the module. RO 0x0
5:0 MINOR Minor revision number of the module. RO 0x02
Override the default 8250 read handler: mem_serial_in()
by a custom handler: serial_in_8250()
which makes sure that RX fifo is not read when empty
tested on zoom3(3630) board
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the hsmmc zoom peripheral configuration to support:
Power saving mode
mmc2 8-bit support
Configure mmc2 as non removable
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TWL4030 keypad driver is not enabled by default for zoom2 and zoom3
boards.
This patch will enable the same for both zoom2 and zoom3 boards.
Tested on zoom2(3430) and zoom3(3630) boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise Extreme Lower Power (ELP) wakeup doesn't work properly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3: zoom2/3: make MMC slot work again
Commit 12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing htcherald_defconfig did not include mux support, which
prevented USB and other functionality from working out of the box.
This change updates the defconfig to add it in. It also aligns the
defconfig to the -rc8 kernel config.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch corrects the issue introduced with one of my earlier patches:
OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.
Applies on top of my prevoius patch:
OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]
Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig
[1] http://patchwork.kernel.org/patch/57922/
[2] http://patchwork.kernel.org/patch/61952/
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Comment in omap_init_devices asks to keep init calls and their
implementations in alphabetical order, so let it be that way.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable minimum features to boot omap4430 on es1.0 samples. v2 versions
removes the "CONFIG_SYSFS_DEPRECATED_V2" since it's deprecated. Without
this older file system doesn't boot. One need to upgrade the filesystem
if getting stuck in first init function.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The secondary cores wakes up in time so the wait loop is not
necessary anymore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the public sram base address and available
size on OMAP4430.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pandora board file updates:
- change keycodes of game buttons
it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
the older DSS driver was never functional on l-o or mainline
kernels due to missing panel driver, so remove unneeded
pandora_lcd platform_device. This also removes last OMAP_TAG
from the board file.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Kevin Hilman <kjh@hilman.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.
Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.
Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Most of the dpll api's from dpll.c are reused for OMAP4.
This patch does extend a few api's for OMAP4 support.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific CM1 and CM2 module
register field masks. Auto generated using a python
script (gen_cm_shifts_and_mask.py) developed by Benoit
Cousson, Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific PRM register bit field
shifts and masks. Auto generated using a python script
(gen_prm_shifts_and_mask.py) developed by Benoit Cousson,
Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds the offsets for new modules in PRM
and CM for OMAP4
These are autogenerated using a python script (gen_prcm44xx_h.py)
developed by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rather than having to do a usecs = nsecs / NSECS_PER_USEC to
track latency in usecs, just track it in nanoseconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
WARN if a clock/hwmod is missing a clockdomain association since
resulting hwmod will not be able to correctly enable/disable clocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
During suspend and resume, when omap_device deactivation and
activation is happening, the timekeeping subsystem has likely already
been suspended. Thus getnstimeofday() will fail and trigger a WARN().
Use read_persistent_clock() instead of getnstimeofday() to avoid this.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The _dev_wakeup_lat_limit field of struct omap_device is u32, so use
UINT_MAX instead of INT_MAX for the default maximum.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Following the model of to_platform_device(), add to_omap_device()
macro so a platform_device pointer can be converted into an
omap_device pointer.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Earlier, the hwmod code had considered the OCP_SYSCONFIG.CLOCKACTIVITY
bits to be incremental power saving bits, controlling internal IP
block clock gates. This was a misapprehension. The CLOCKACTIVITY
bits are used to indicate, in advance, which clocks will be cut when
the module acknowledges an idle request. This enables the IP block to
take whatever action is necessary to complete any in-progress work
before asserting its IdleAck.
In the current Linux-OMAP code, this implies that the clock framework
should be changing module CLOCKACTIVITY bits as module clocks are enabled
and disabled. We don't do that yet, but in the future, we should.
This must wait until the clock tree is annotated with omap_hwmod pointers
(or vice-versa). In the meantime, drop most of the hwmod code that
controls CLOCKACTIVITY bits to avoid confusion.
This patch has benefited from many illuminating discussions with (in
alphabetical order) Benoît Cousson <b-cousson@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Sebastien Sabatier <s-sabatier1@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Sebastien Sabatier <s-sabatier1@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info. Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.
Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.
After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable. If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable. Upon module disable, AUTOIDLE will be set to
1.
Enabling module autoidle should save some power. The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.
Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Reprogram the module's OCP_SYSCONFIG register after module reset (SOFTRESET
= 1). This may not be needed, but the definition of the reset performed by
the SOFTRESET bit is unclear.
Kevin Hilman <khilman@deeprootsystems.com> tested an earlier version of
this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.
This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>. A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Juha Leppänen <juha_motorsportcom@luukku.com>
Cc: Russell King <linux@arm.linux.org.uk>
MPU power domain bank 0 bits are displayed in position of bank 1
in PWRSTS and PREPWRSTS registers. So read them from correct
position
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The code that reprograms the SDRC memory controller during CORE DVFS,
mach-omap2/sram34xx.S:omap3_sram_configure_core_dpll(), does not
ensure that all L3 initiators are prevented from accessing the SDRAM
before modifying the SDRC AC timing and MR registers. This can cause
memory to be corrupted or cause the SDRC to enter an unpredictable
state. This patch places that code behind a Kconfig option,
CONFIG_OMAP3_SDRC_AC_TIMING for now, and adds a note explaining what
is going on. Ideally the code can be added back in once supporting
code is present to ensure that other initiators aren't touching the
SDRAM. At the very least, these registers should be reprogrammable
during kernel init to deal with buggy bootloaders. Users who know
that all other system initiators will not be touching the SDRAM can
also re-enable this Kconfig option.
This is a modification of a patch originally written by Rajendra Nayak
<rnayak@ti.com> (the original is at http://patchwork.kernel.org/patch/51927/).
Rather than removing the code completely, this patch just comments it out.
Thanks to Benoît Cousson <b-cousson@ti.com> and Christophe Sucur
<c-sucur@ti.com> for explaining the technical basis for this and for
explaining what can be done to make this path work in future code.
Thanks to Richard Woodruff <r-woodruff2@ti.com>, Nishanth Menon
<nm@ti.com>, and Olof Johansson <olof@lixom.net> for their comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Christophe Sucur <c-sucur@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Olof Johansson <olof@lixom.net>
IS_ERR returns only 1 or 0, and the functions return a negative error
in other cases anyways.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP24xx chips don't support software-configurable sleep dependencies.
Test early for this so the compiler can redact the entire function body
on OMAP24xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Avoid cluttering the Kconfig space with debug options that are rarely
used. These can now be enabled and disabled by patching the "#undef DEBUG"
in the source files with "#define DEBUG", conforming to the practice for
the rest of the linux-omap code.
Also, while we're here, some lines in plat-omap/Kconfig use sets of
leading spaces when those lines should start with tabs. Convert most
of them to use tabs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Device drivers and loadable modules should not be calling these
prm_* and cm_* functions, so stop exporting them. Only core code
and device driver integration code (in arch/arm/*omap*) should
call these functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP1 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the mpu_rate data structures out into their own
files, opp.h and opp_data.c. In the long run, these mpu_rate tables
should be replaced with OPP code.
Also includes a patch from Felipe Balbi <felipe.balbi@nokia.com> to
mark omap1_clk_functions as __initdata to avoid a section warning:
http://patchwork.kernel.org/patch/64366/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Nishanth Menon <nm@ti.com>
mach-omap1/clock.c:omap1_clk_disable_unused() contains a test that
assumes that the clock structures are available in the file's
namespace. After a following patch, this will no longer be the case.
So we need to reimplement that test. It turns out that we already
have a facility in the clock framework to handle this case - the
ENABLE_ON_INIT flag - used on OMAP2/3. Remove the offending test and
mark the clocks that it was intended to catch as ENABLE_ON_INIT.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the prcm_config data structures out into their own
files, opp2xxx.h and opp24{2,3}0_data.c, and only build in the OPP tables
for the target device. This should save some memory. In the long run,
these prcm_config tables should be replaced with OPP code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
The OMAP3 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
cpu_mask is reused in the OMAP2xxx clock code to match against both the
CPU-specific rate flags (e.g., RATE_IN_2420) and the OMAP clkdev integration
code CPU flags (e.g., CK_242X). This means that any patch that renumbers the
CK_* macros, as the next patch does, will probably break. This patch
separates the clkdev_omap and clksel_rate CPU type detection flags so
the CK_* macros can be renumbered freely.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
clock34xx.c contains some macros which probably belong in mach-omap2/sdrc.h.
Move those macros to mach-omap2/sdrc.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Similar to the previous patch, the APLL code relied on the presence of the
static struct clks in its own namespace. The APLL code didn't use them for
validation, however - it adjusted its own internal state depending on
the struct clk * that called it. Now that static struct clks are
leaving the clock24xx.c namespace, use a more durable method: split the
omap2_clk_fixed_enable() function into omap2_clk_apll96_enable() and
omap2_clk_apll54_enable(). They still share a disable function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some parts of the clock code took advantage of the fact that the statically
allocated clock tree was in clock{,24xx,34xx}.c's local namespace to do some
extra argument checks. These are overzealous and are more difficult to
maintain when the clock tree is in a separate namespace, so, remove them.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New helper - sys_mmap_pgoff(); switch syscalls to using it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add missing include for msm_sdcc compilation, and remove pwrsink
support that is not mainline, yet.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[dwalker@codeaurora.org : fixed indent in mmc.h]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
* 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux:
ARM: S3C24XX: DMA: Use valid index when accessing array
ARM: S3C: move s3c_pwm_remove to .devexit.text
ARM: S3C24XX: Export s3c24xx_set_fiq for modules.
ARM: S3C: move s3c_adc_remove to .devexit.text
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (69 commits)
davinci: Initial support for Neuros OSD2 platform.
davinci: remove unused variable in arch/arm/mach-davinci/board-sffsdr.c
davinci: fix section mismatch warning in arch/arm/mach-davinci/board-dm646x-evm.c
DaVinci: DM365: Enable DaVinci RTC support for DM365 EVM
DA8xx/OMAP-L1xx: Add high speed SD/MMC capabilities
davinci: DA8XX/OMAP-L1XX: enable cpuidle and regulator in defconfig
davinci: DA850/OMAP-L138: avoid using separate initcall for initializing regulator
davinci: DA850/OMAP-L138 EVM: register for cpuidle support
davinci: DA8XX/OMAP-L1XX: add support for cpuidle driver register
davinci: add CPU idle driver
davinci: DA8XX/OMAP-L1XX: fix compiler warning
davinci: DA850/OMAP-L138: eliminate static function declaration
davinci: DA850/OMAP-L138 EVM: simplify configuration of emac in MII/RMII mode
davinci: DA850/OMAP-L138 EVM: get rid of DA850_UI_EXP config option
davinci: DA850/OMAP-L138 EVM: implement autodetect of RMII PHY
davinci: DA830/OMAP-L137 EVM: do not configure NAND on UI card when MMC/SD is selected
davinci: DA830/OMAP-L137 EVM: use runtime detection for UI card
davinci: DA830/OMAP-L137 EVM: remove ifdefs inside da830_evm_init()
davinci: DA830/OMAP-L137 EVM: fix warning with default config
davinci: Add NAND support for DA830/OMAP-L137 EVM platform
...
A previous patch was introducing a SPARSEMEM dependency on
!HIGH_PHYS_OFFSET but it should actually be !REALVIEW_HIGH_PHYS_OFFSET.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since this IRQ descriptor doesn't have an action registered, it is
allowed for probing via probe_irq_on/off() and it will be disabled by
the latter function. This patch sets the IRQ_NOPROBE status bit for the
local timer descriptor.
Signed-off-by: Varun Swara <Varun.Swara@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The core files of DSS2. DSS2 commits are split a bit artificially to
make the individual commits smaller, and DSS2 doesn't compile properly
without the rest of the core commits. This shouldn't be a problem, as no
configuration uses DSS2 yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
VRFB rotation engine is a block in OMAP2/3 that offers 12 independent
contexts that can be used for framebuffer rotation.
Each context has a backend area of real memory, where it stores the
pixels in undisclosed format. This memory is offered to users via 4
virtual memory areas, which see the same memory area in different
rotation angles (0, 90, 180 and 270 degrees).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:
- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations
The upcoming DSS2 uses VRAM manager.
VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The upcoming new display subsystem driver is divided to two devices,
omapdss and omapfb, of which omapdss handles the actual hardware.
This patch adds a dummy omapdss platform device for the current omapfb
driver, which is then used to get the clocks. This will make it possible
for the current and the new display drivers to co-exist.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:
include/linux/omapfb.h - ioctls etc for userspace and some kernel
stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use
This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This patch allows an earlyprintk console if CONFIG_DEBUG_LL is enabled,
using the printch asm function.
The patch is based on the original work by Sascha Hauer.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
SMS_ROT_* registers are used by VRFB rotation engine.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
The DMA_CH_VALID bit used in the channel index should be masked out before
using it to access the channel array.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
The function s3c_pwm_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Allow s3c24xx_set_fiq() to be exported so that it can be used by modules
wanting FIQ support.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The function s3c_adc_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-By: Ben Dooks <ben@simtec.co.uk>
Cc: Ramax Lo <ramaxlo@gmail.com>
Cc: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: linux-kernel@vger.kernel.org
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Many features of h3100/h3600 (LCD, PCMCIA, Flash write, etc.)
depend on correct functioning of GPIO expander handled by htc-egpio
driver, so force its building in Kconfig.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update defconfig to current kernel, enable support for iPAQ H3100
and following drivers: gpio-keys, htc-egpio, ide_cs.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for "Power" and "Action" (joystick center) buttons -
the only buttons on iPaq h3100/h3600 connected to GPIOs
(other buttons are controlled by microcontroller)
Also remove setting PWER for wakeup on Power button press -
gpio-keys driver will handle it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After a code reorganization and following split, there's some #includes
now unused. Clean them up and sort remaining alphabetticaly where possible.
Compile tested.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct boilerplates after files split. Also shorten them a bit - use
standart GPL wording (as per http://lkml.org/lkml/2007/5/1/220) and
drop changelog, which only entry about h3800 support and abstracted
EGPIOs is just confusing now, as both of these features are gone.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split common h3600.c into three separate files: h3100.c, h3600.c and
h3xxx.c (the latter contains common code for h3100/h3600)
Copyright boilerplates and #includes are copied intact and will be
cleaned up later.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Combine both headers into one, rename to h3xxx.h and change all
users accordingly.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all existing code was converted to gpiolib, drop no more
used pre-gpiolib (bit-shifted) GPIO definintions.
Supply new gpiolib-friendly definitions for GPIOs which
don't have them yet.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After conversion to gpiolib there's still some GPIOs left, that get
configured in *_mach_init() as outputs (using direct operations
on GPCR/GPDR registers), but otherwise unused. These GPIOs are mainly
sound related and should be configured by corresponding driver once
it is written.
Drop this initialisation and configure all GPIOs as input.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all the remaining users of these definitions
(in pcmcia/sa1100_h3600 driver) were converted to gpio_to_irq(),
they can be safely removed.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all users of assign_h3600_egpio now converted to gpiolib, we
can safely remove all assign_h3600_egpio handling code and
definitions.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use of gpio_request/gpio_free in some callbacks may look ugly, but
corresponding drivers (sa1100_serial and sa1100_fb) don't provide (yet)
init/exit hooks and registering these gpios in *_mach_init is also
not possible, because htc-gpio driver starts a bit later...
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It will be used for future conversion of assign_h3600_egpio calls to
gpiolib.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
h3100 and h3600 have different sets of LCD-controlling gpios,
which mapped to the same "abstracted" EGPIO.
As we plan to get rid of those abstracted egpios completely, we
need to separate these helper functions.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PM_SUSPEND, PM_RESUME and machine_is_h3xxx() are not used anywhere in
kernel (checked with git grep), so it's safe to remove them.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRDA is handled by separate sa1100-ir driver and has
nothing to do with sa1100_serial
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No point calling sa1100_register_uart_fns early - these aren't
used until late in the boot sequence. Also convert to gpiolib
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PrPMC1100 is handled by IXDP425 platform code, there is no need for
duplicate set of macros. Remove them.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
IXP4xx CPUs can indirectly access the whole 4 GB PCI MMIO address space (using
the non-prefetch registers). Previously the available space depended on the CPU
variant, since one of the IXP43x platforms needed more than the usual 128 MB.
1 GB should be enough for everyone, and if not, we can trivially increase it.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Instead of including the heavy linux/mm.h for VMALLOC_START, test the addresses
against PCI MIN and MAX addresses. Indirect PCI uses 1:1 mapping for MMIO space
making this change possible.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Clock generators used by IXP4xx processors are usually 33.333 MHz, sometimes
33.33 MHz and few platforms use 33 MHz. The timers tick twice as fast,
that means 66.666, 66.66 or 66 MHz. Current 66.666666 MHz means 10 ppm
offset from the usual 66.666 MHz.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dirk Behme reported instability on ARM11 SMP (VIPT non-aliasing cache)
caused by the dynamic linker changing protection on text pages to write
GOT entries. The problem is due to an interaction between the write
faulting code providing new anonymous pages which are incoherent with
the I-cache due to write buffering, and the I-cache not having been
invalidated.
a4db94d plugs the hole with the data cache coherency. This patch
provides the other half of the fix by flushing the I-cache in
flush_cache_range() for VM_EXEC VMAs (which is what we have when the
region is being made executable again.) This ensures that the I-cache
will be up to date with the newly COW'd pages.
Note: if users are writing instructions, then they still need to use
the ARM sys_cacheflush API to ensure that the caches are correctly
synchronized.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
flush_cache_mm() is called in two cases:
1. when a process exits, just before the page tables are torn down.
We can allow the stale lines to evict themselves over time without
causing any harm.
2. when a process forks, and we've allocated a new ASID.
The instruction cache issues are dealt with as pages are brought
into the new process address space. Flushing the I-cache here is
therefore unnecessary.
However, we must keep the VIPT aliasing D-cache flush to ensure that
any dirty cache lines are not written back after the pages have been
reallocated for some other use - which would result in corruption.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The I and D caches for copy-on-write pages on processors with
write-allocate caches become incoherent causing problems on application
relying on CoW for text pages (dynamic linker relocating symbols in a
text page). This patch flushes the D-cache for such pages.
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both call sites for __flush_dcache_page() end up calling
__flush_icache_all() themselves, so having __flush_dcache_page() do
this as well is wasteful. Remove the duplicated icache flushing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, linux-next breaks due to a typo introduced in commit
33c4d91928
This patch fixes it.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The symbols aren't declared and don't need to be exported, they go
along with the device structure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
The naming of the defines suggests that there are three IISv4 ports
with one data line each when in fact there is a single IISv4 port
with three data lines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If running in non-secure mode accessing
some registers of l2x0 will fault. So
check if l2x0 is already enabled, if so
do not access those secure registers.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
removed old macro definition for io access, using
the generic macros defined in asm/io.h
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Having one combined defconfig that is the superset of the individual
defconfigs for OMAP3 platforms is useful for easily finding build
errors. Not to mention convenient as a base if you want to boot several
platforms with a single kernel image.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch configures iomux and i2c io expander in order to add
support to SD/MMC cards on i-MXT TD60.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This enables on-chip tracing components found in omap3xxx.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This driver implements support for on-chip Embedded Tracing Macrocell and
Embedded Trace Buffer. It allows to trigger tracing of kernel execution flow
and exporting trace output to userspace via character device and a sysrq
combo.
Trace output can then be decoded by a fairly simple open source tool [1]
which is already sufficient to get the idea of what the kernel is doing.
[1]: http://github.com/virtuoso/etm2human
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The zero page is read-only, and has its cache state cleared during
boot. No further maintanence for this page is required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
page_address() is a function call rather than a macro, and so:
if (page_address(page))
do_something(page_address(page));
results in two calls to this function. This is unnecessary; remove
the duplication.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
