Some devices do not produce timestamps that correspond to the end of the
frame. The user space should be informed on the matter. This patch achieves
that by adding buffer flags (and a mask) for timestamp sources since more
possible timestamping points are expected than just two.
A three-bit mask is defined (V4L2_BUF_FLAG_TSTAMP_SRC_MASK) and two of the
eight possible values is are defined V4L2_BUF_FLAG_TSTAMP_SRC_EOF for end of
frame (value zero) V4L2_BUF_FLAG_TSTAMP_SRC_SOE for start of exposure (next
value).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buffer flags field is 32 bits but the defined only used 16. This is
fine, but as more than 16 bits will be used in the very near future, define
them as 32-bit numbers for consistency.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modern silicon RF tuners used nowadays has many controllable gain
stages on signal path. Usually, but not always, there is at least
3 gain stages. Also on some cases there could be multiple gain
stages within the ones specified here. However, I think that having
these three controllable gain stages offers enough fine-tuning for
real use cases.
1) LNA gain. That is first gain just after antenna input.
2) Mixer gain. It is located quite middle of the signal path, where
RF signal is down-converted to IF/BB.
3) IF gain. That is last gain in order to adjust output signal level
to optimal level for receiving party (usually demodulator ADC).
Each gain stage could be set rather often both manual or automatic
(AGC) mode. Due to that add separate controls for controlling
operation mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDIOC_QUERYCAP IOCTL is used to query device capabilities. Add new
capability flag to inform given device supports SDR capture.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add new V4L2 stream format definition, V4L2_BUF_TYPE_SDR_CAPTURE,
for SDR receiver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Define tuner types V4L2_TUNER_ADC and V4L2_TUNER_RF for SDR usage.
ADC is used for setting sampling rate (sampling frequency) to SDR
device.
Another tuner type, named as V4L2_TUNER_RF, is possible RF tuner.
Is is used to down-convert RF frequency to range ADC could sample.
Having RF tuner is optional, whilst in practice it is almost always
there.
Also add checks to VIDIOC_G_FREQUENCY, VIDIOC_S_FREQUENCY and
VIDIOC_ENUM_FREQ_BANDS only allow these two tuner types when device
type is SDR (VFL_TYPE_SDR). For VIDIOC_G_FREQUENCY we do not check
tuner type, instead override type with V4L2_TUNER_ADC in every
case (requested by Hans in order to keep functionality in line with
existing tuners and existing API does not specify it).
Prohibit VIDIOC_S_HW_FREQ_SEEK explicitly when device type is SDR,
as device cannot do hardware seek without a hardware demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adding V4L2 controls for horizontal and vertical search range in pixels
for motion estimation module in video encoder.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VESA added two new DMT timings in their latest standard document. Add these
to v4l2-dv-timings.h.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
Pull btrfs updates from Chris Mason:
"This is a pretty big pull, and most of these changes have been
floating in btrfs-next for a long time. Filipe's properties work is a
cool building block for inheriting attributes like compression down on
a per inode basis.
Jeff Mahoney kicked in code to export filesystem info into sysfs.
Otherwise, lots of performance improvements, cleanups and bug fixes.
Looks like there are still a few other small pending incrementals, but
I wanted to get the bulk of this in first"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (149 commits)
Btrfs: fix spin_unlock in check_ref_cleanup
Btrfs: setup inode location during btrfs_init_inode_locked
Btrfs: don't use ram_bytes for uncompressed inline items
Btrfs: fix btrfs_search_slot_for_read backwards iteration
Btrfs: do not export ulist functions
Btrfs: rework ulist with list+rb_tree
Btrfs: fix memory leaks on walking backrefs failure
Btrfs: fix send file hole detection leading to data corruption
Btrfs: add a reschedule point in btrfs_find_all_roots()
Btrfs: make send's file extent item search more efficient
Btrfs: fix to catch all errors when resolving indirect ref
Btrfs: fix protection between walking backrefs and root deletion
btrfs: fix warning while merging two adjacent extents
Btrfs: fix infinite path build loops in incremental send
btrfs: undo sysfs when open_ctree() fails
Btrfs: fix snprintf usage by send's gen_unique_name
btrfs: fix defrag 32-bit integer overflow
btrfs: sysfs: list the NO_HOLES feature
btrfs: sysfs: don't show reserved incompat feature
btrfs: call permission checks earlier in ioctls and return EPERM
...
Pull block IO driver changes from Jens Axboe:
- bcache update from Kent Overstreet.
- two bcache fixes from Nicholas Swenson.
- cciss pci init error fix from Andrew.
- underflow fix in the parallel IDE pg_write code from Dan Carpenter.
I'm sure the 1 (or 0) users of that are now happy.
- two PCI related fixes for sx8 from Jingoo Han.
- floppy init fix for first block read from Jiri Kosina.
- pktcdvd error return miss fix from Julia Lawall.
- removal of IRQF_SHARED from the SEGA Dreamcast CD-ROM code from
Michael Opdenacker.
- comment typo fix for the loop driver from Olaf Hering.
- potential oops fix for null_blk from Raghavendra K T.
- two fixes from Sam Bradshaw (Micron) for the mtip32xx driver, fixing
an OOM problem and a problem with handling security locked conditions
* 'for-3.14/drivers' of git://git.kernel.dk/linux-block: (47 commits)
mg_disk: Spelling s/finised/finished/
null_blk: Null pointer deference problem in alloc_page_buffers
mtip32xx: Correctly handle security locked condition
mtip32xx: Make SGL container per-command to eliminate high order dma allocation
drivers/block/loop.c: fix comment typo in loop_config_discard
drivers/block/cciss.c:cciss_init_one(): use proper errnos
drivers/block/paride/pg.c: underflow bug in pg_write()
drivers/block/sx8.c: remove unnecessary pci_set_drvdata()
drivers/block/sx8.c: use module_pci_driver()
floppy: bail out in open() if drive is not responding to block0 read
bcache: Fix auxiliary search trees for key size > cacheline size
bcache: Don't return -EINTR when insert finished
bcache: Improve bucket_prio() calculation
bcache: Add bch_bkey_equal_header()
bcache: update bch_bkey_try_merge
bcache: Move insert_fixup() to btree_keys_ops
bcache: Convert sorting to btree_keys
bcache: Convert debug code to btree_keys
bcache: Convert btree_iter to struct btree_keys
bcache: Refactor bset_tree sysfs stats
...
Pull drm updates from Dave Airlie:
"Been a bit busy, first week of kids school, and waiting on other trees
to go in before I could send this, so its a bit later than I'd
normally like.
Highlights:
- core:
timestamp fixes, lots of misc cleanups
- new drivers:
bochs virtual vga
- vmwgfx:
major overhaul for their nextgen virt gpu.
- i915:
runtime D3 on HSW, watermark fixes, power well work, fbc fixes,
bdw is no longer prelim.
- nouveau:
gk110/208 acceleration, more pm groundwork, old overlay support
- radeon:
dpm rework and clockgating for CIK, pci config reset, big endian
fixes
- tegra:
panel support and DSI support, build as module, prime.
- armada, omap, gma500, rcar, exynos, mgag200, cirrus, ast:
fixes
- msm:
hdmi support for mdp5"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (595 commits)
drm/nouveau: resume display if any later suspend bits fail
drm/nouveau: fix lock unbalance in nouveau_crtc_page_flip
drm/nouveau: implement hooks for needed for drm vblank timestamping support
drm/nouveau/disp: add a method to fetch info needed by drm vblank timestamping
drm/nv50: fill in crtc mode struct members from crtc_mode_fixup
drm/radeon/dce8: workaround for atom BlankCrtc table
drm/radeon/DCE4+: clear bios scratch dpms bit (v2)
drm/radeon: set si_notify_smc_display_change properly
drm/radeon: fix DAC interrupt handling on DCE5+
drm/radeon: clean up active vram sizing
drm/radeon: skip async dma init on r6xx
drm/radeon/runpm: don't runtime suspend non-PX cards
drm/radeon: add ring to fence trace functions
drm/radeon: add missing trace point
drm/radeon: fix VMID use tracking
drm: ast,cirrus,mgag200: use drm_can_sleep
drm/gma500: Lock struct_mutex around cursor updates
drm/i915: Fix the offset issue for the stolen GEM objects
DRM: armada: fix missing DRM_KMS_FB_HELPER select
drm/i915: Decouple GPU error reporting from ring initialisation
...
Pull more x32 uabi type fixes from Peter Anvin:
"Despite the branch name, **most of these changes are to generic
code**. They change types so that they make an increasing amount of
the exported uapi kernel headers usable for libc.
The ARM64 people are also interested in these changes for their ILP32
ABI"
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
uapi: Use __kernel_long_t in struct mq_attr
uapi: Use __kernel_ulong_t in shmid64_ds/shminfo64/shm_info
x86, uapi, x32: Use __kernel_ulong_t in x86 struct semid64_ds
uapi: Use __kernel_ulong_t in struct msqid64_ds
uapi: Use __kernel_long_t in struct msgbuf
uapi, asm-generic: Use __kernel_ulong_t in uapi struct ipc64_perm
uapi: Use __kernel_long_t/__kernel_ulong_t in <linux/resource.h>
uapi: Use __kernel_long_t in struct timex
This change adds infrastructure to allow for generic properties for
inodes. Properties are name/value pairs that can be associated with
inodes for different purposes. They are stored as xattrs with the
prefix "btrfs."
Properties can be inherited - this means when a directory inode has
inheritable properties set, these are added to new inodes created
under that directory. Further, subvolumes can also have properties
associated with them, and they can be inherited from their parent
subvolume. Naturally, directory properties have priority over subvolume
properties (in practice a subvolume property is just a regular
property associated with the root inode, objectid 256, of the
subvolume's fs tree).
This change also adds one specific property implementation, named
"compression", whose values can be "lzo" or "zlib" and it's an
inheritable property.
The corresponding changes to btrfs-progs were also implemented.
A patch with xfstests for this feature will follow once there's
agreement on this change/feature.
Further, the script at the bottom of this commit message was used to
do some benchmarks to measure any performance penalties of this feature.
Basically the tests correspond to:
Test 1 - create a filesystem and mount it with compress-force=lzo,
then sequentially create N files of 64Kb each, measure how long it took
to create the files, unmount the filesystem, mount the filesystem and
perform an 'ls -lha' against the test directory holding the N files, and
report the time the command took.
Test 2 - create a filesystem and don't use any compression option when
mounting it - instead set the compression property of the subvolume's
root to 'lzo'. Then create N files of 64Kb, and report the time it took.
The unmount the filesystem, mount it again and perform an 'ls -lha' like
in the former test. This means every single file ends up with a property
(xattr) associated to it.
Test 3 - same as test 2, but uses 4 properties - 3 are duplicates of the
compression property, have no real effect other than adding more work
when inheriting properties and taking more btree leaf space.
Test 4 - same as test 3 but with 10 properties per file.
Results (in seconds, and averages of 5 runs each), for different N
numbers of files follow.
* Without properties (test 1)
file creation time ls -lha time
10 000 files 3.49 0.76
100 000 files 47.19 8.37
1 000 000 files 518.51 107.06
* With 1 property (compression property set to lzo - test 2)
file creation time ls -lha time
10 000 files 3.63 0.93
100 000 files 48.56 9.74
1 000 000 files 537.72 125.11
* With 4 properties (test 3)
file creation time ls -lha time
10 000 files 3.94 1.20
100 000 files 52.14 11.48
1 000 000 files 572.70 142.13
* With 10 properties (test 4)
file creation time ls -lha time
10 000 files 4.61 1.35
100 000 files 58.86 13.83
1 000 000 files 656.01 177.61
The increased latencies with properties are essencialy because of:
*) When creating an inode, we now synchronously write 1 more item
(an xattr item) for each property inherited from the parent dir
(or subvolume). This could be done in an asynchronous way such
as we do for dir intex items (delayed-inode.c), which could help
reduce the file creation latency;
*) With properties, we now have larger fs trees. For this particular
test each xattr item uses 75 bytes of leaf space in the fs tree.
This could be less by using a new item for xattr items, instead of
the current btrfs_dir_item, since we could cut the 'location' and
'type' fields (saving 18 bytes) and maybe 'transid' too (saving a
total of 26 bytes per xattr item) from the btrfs_dir_item type.
Also tried batching the xattr insertions (ignoring proper hash
collision handling, since it didn't exist) when creating files that
inherit properties from their parent inode/subvolume, but the end
results were (surprisingly) essentially the same.
Test script:
$ cat test.pl
#!/usr/bin/perl -w
use strict;
use Time::HiRes qw(time);
use constant NUM_FILES => 10_000;
use constant FILE_SIZES => (64 * 1024);
use constant DEV => '/dev/sdb4';
use constant MNT_POINT => '/home/fdmanana/btrfs-tests/dev';
use constant TEST_DIR => (MNT_POINT . '/testdir');
system("mkfs.btrfs", "-l", "16384", "-f", DEV) == 0 or die "mkfs.btrfs failed!";
# following line for testing without properties
#system("mount", "-o", "compress-force=lzo", DEV, MNT_POINT) == 0 or die "mount failed!";
# following 2 lines for testing with properties
system("mount", DEV, MNT_POINT) == 0 or die "mount failed!";
system("btrfs", "prop", "set", MNT_POINT, "compression", "lzo") == 0 or die "set prop failed!";
system("mkdir", TEST_DIR) == 0 or die "mkdir failed!";
my ($t1, $t2);
$t1 = time();
for (my $i = 1; $i <= NUM_FILES; $i++) {
my $p = TEST_DIR . '/file_' . $i;
open(my $f, '>', $p) or die "Error opening file!";
$f->autoflush(1);
for (my $j = 0; $j < FILE_SIZES; $j += 4096) {
print $f ('A' x 4096) or die "Error writing to file!";
}
close($f);
}
$t2 = time();
print "Time to create " . NUM_FILES . ": " . ($t2 - $t1) . " seconds.\n";
system("umount", DEV) == 0 or die "umount failed!";
system("mount", DEV, MNT_POINT) == 0 or die "mount failed!";
$t1 = time();
system("bash -c 'ls -lha " . TEST_DIR . " > /dev/null'") == 0 or die "ls failed!";
$t2 = time();
print "Time to ls -lha all files: " . ($t2 - $t1) . " seconds.\n";
system("umount", DEV) == 0 or die "umount failed!";
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
btrfs filesystem df output will show the size of the metadata space
and how much of it is used, and the user assumes that the difference
is all usable space. Since that's not actually the case due to the
global metadata reservation, we should provide the full picture to the
user.
This patch adds an ioctl that exports the size of the global metadata
reservation so that btrfs filesystem df can report it.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <clm@fb.com>
There are some feature bits that require no offline setup and can
be enabled online. I've only reviewed extended irefs, but there will
probably be more.
We introduce three new ioctls:
- BTRFS_IOC_GET_SUPPORTED_FEATURES: query the kernel for supported features.
- BTRFS_IOC_GET_FEATURES: query the kernel for enabled features on a per-fs
basis, as well as querying for which features are changeable with mounted.
- BTRFS_IOC_SET_FEATURES: change features on a per-fs basis.
We introduce two new masks per feature set (_SAFE_SET and _SAFE_CLEAR) that
allow us to define which features are safe to change at runtime.
The failure modes for BTRFS_IOC_SET_FEATURES are as follows:
- Enabling a completely unsupported feature: warns and returns -ENOTSUPP
- Enabling a feature that can only be done offline: warns and returns -EPERM
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <clm@fb.com>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
All bug fixes, two tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=d81E
-----END PGP SIGNATURE-----
Merge tag 'md/3.14' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"All bug fixes, two tagged for -stable"
* tag 'md/3.14' of git://neil.brown.name/md:
md/raid5: close recently introduced race in stripe_head management.
md/raid5: fix long-standing problem with bitmap handling on write failure.
md: check command validity early in md_ioctl().
md: ensure metadata is writen after raid level change.
md/raid10: avoid fullsync when not necessary.
md: allow a partially recovered device to be hot-added to an array.
md: Change handling of save_raid_disk and metadata update during recovery.
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJS3a1eAAoJEILEb/54YlRxnTgP/iGawvgjKWm6Qqp7WSIvd5gQ
zZ6q75C6Pc/W2fq1+OzVGnpCF8WYFy+nFDAXOvUHjIXuoxSwFcuW5l4aMckgl/0a
TXEWe9MJrCHHRfDApfFacCJ44U02bjJAD5vTyL/hKA+IHeinq4WCSojryYC+8jU0
cBrUIV0aNH8r5JR2WJNAyv/U29rXsDUOu0I4qTqZ4YaZT6AignMjtLXn1e9AH1Pn
DPZphTIo/HMnb+kgBOjt4snMk+ahVO9eCOxh/hH8ecnWExw9WynXoU5Nsna0tSZs
ssyHC7BYexD3oYsG8D52cFUpp4FCsJ0nFQNa2kw0LY+0FBNay43LySisKYHZPXEs
2WpESDv+/t7yhtnrvM+TtA7aBheKm2XMWGFSu/aERLE17jIidOkXKH5Y7ryYLNf/
uyRKxNS0NcZWZ0G+/wuY02jQYNkfYz3k/nTr8BAUItRBjdporGIRNEnR9gPzgCUC
uQhjXWMPulqubr8xbyefPWHTEzU2nvbXwTUWGjrBxSy8zkyy5arfqizUj+VG6afT
NsboANoMHa9b+xdzigSFdA3nbVK6xBjtU6Ywntk9TIpODKF5NgfARx0H+oSH+Zrj
32bMzgZtHw/lAbYsnQ9OnTY6AEWQYt6NMuVbTiLXrMHhM3nWwfg/XoN4nZqs6jPo
IYvE6WhQZU6L6fptGHFC
=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This is in net-next only, for couple of days. Not used anymore, and never
should have been. So just remove it and pretend it was never there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge second patch-bomb from Andrew Morton:
- various misc bits
- the rest of MM
- add generic fixmap.h, use it
- backlight updates
- dynamic_debug updates
- printk() updates
- checkpatch updates
- binfmt_elf
- ramfs
- init/
- autofs4
- drivers/rtc
- nilfs
- hfsplus
- Documentation/
- coredump
- procfs
- fork
- exec
- kexec
- kdump
- partitions
- rapidio
- rbtree
- userns
- memstick
- w1
- decompressors
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (197 commits)
lib/decompress_unlz4.c: always set an error return code on failures
romfs: fix returm err while getting inode in fill_super
drivers/w1/masters/w1-gpio.c: add strong pullup emulation
drivers/memstick/host/rtsx_pci_ms.c: fix ms card data transfer bug
userns: relax the posix_acl_valid() checks
arch/sh/kernel/dwarf.c: use rbtree postorder iteration helper instead of solution using repeated rb_erase()
fs-ext3-use-rbtree-postorder-iteration-helper-instead-of-opencoding-fix
fs/ext3: use rbtree postorder iteration helper instead of opencoding
fs/jffs2: use rbtree postorder iteration helper instead of opencoding
fs/ext4: use rbtree postorder iteration helper instead of opencoding
fs/ubifs: use rbtree postorder iteration helper instead of opencoding
net/netfilter/ipset/ip_set_hash_netiface.c: use rbtree postorder iteration instead of opencoding
rbtree/test: test rbtree_postorder_for_each_entry_safe()
rbtree/test: move rb_node to the middle of the test struct
rapidio: add modular rapidio core build into powerpc and mips branches
partitions/efi: complete documentation of gpt kernel param purpose
kdump: add /sys/kernel/vmcoreinfo ABI documentation
kdump: fix exported size of vmcoreinfo note
kexec: add sysctl to disable kexec_load
fs/exec.c: call arch_pick_mmap_layout() only once
...
Pull audit update from Eric Paris:
"Again we stayed pretty well contained inside the audit system.
Venturing out was fixing a couple of function prototypes which were
inconsistent (didn't hurt anything, but we used the same value as an
int, uint, u32, and I think even a long in a couple of places).
We also made a couple of minor changes to when a couple of LSMs called
the audit system. We hoped to add aarch64 audit support this go
round, but it wasn't ready.
I'm disappearing on vacation on Thursday. I should have internet
access, but it'll be spotty. If anything goes wrong please be sure to
cc rgb@redhat.com. He'll make fixing things his top priority"
* git://git.infradead.org/users/eparis/audit: (50 commits)
audit: whitespace fix in kernel-parameters.txt
audit: fix location of __net_initdata for audit_net_ops
audit: remove pr_info for every network namespace
audit: Modify a set of system calls in audit class definitions
audit: Convert int limit uses to u32
audit: Use more current logging style
audit: Use hex_byte_pack_upper
audit: correct a type mismatch in audit_syscall_exit()
audit: reorder AUDIT_TTY_SET arguments
audit: rework AUDIT_TTY_SET to only grab spin_lock once
audit: remove needless switch in AUDIT_SET
audit: use define's for audit version
audit: documentation of audit= kernel parameter
audit: wait_for_auditd rework for readability
audit: update MAINTAINERS
audit: log task info on feature change
audit: fix incorrect set of audit_sock
audit: print error message when fail to create audit socket
audit: fix dangling keywords in audit_log_set_loginuid() output
audit: log on errors from filter user rules
...
The u64 type is not defined in any exported kernel headers, so trying to
use it will lead to build failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This header uses _IOW/_IOR defines but doesn't include ioctl.h for it.
If you try to use this w/out including ioctl.h yourself, it can fail to
build, so add the explicit include.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This header uses enum NPmode but doesn't include ppp_defs.h. If you try
to use this header w/out including the defs header first, it leads to a
build failure. So add the explicit include to fix it.
Don't know of any packages directly impacted, but noticed while building
some ppp code by hand.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now all 64-bit architectures have been converted to int-ll64.h, we can
remove int-l64.h in kernelspace.
For backwards compatibility, alpha, ia64, mips64, and powerpc64 still
use int-l64.h in userspace.
This is the (reworked for UAPI) non-documentation part of more than two
year old "asm/types.h: All architectures use int-ll64.h in kernelspace"
(https://lkml.org/lkml/2011/8/13/104)
Since <asm/types.h> (from include/uapi/asm-generic/types.h) is used for
both kernel and user space, include/asm-generic/int-ll64.h cannot just
become include/asm-generic/types.h, as Arnd suggested.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent patch
bonding: add netlink attributes to slave link dev (1d3ee88ae0)
Introduced yet another device specific way to access slave information
over rtnetlink. There is one already there for bridge.
This patch introduces generic way to do this, for getting and setting
info as well by extending link_ops. Later on, this new interface will
be used for bridge ports as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing major here, just bugfixes all over the place. The most
interesting part is the ARM guys' virtualized interrupt controller
overhaul, which lets userspace get/set the state and thus enables
migration of ARM VMs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=8sYU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First round of KVM updates for 3.14; PPC parts will come next week.
Nothing major here, just bugfixes all over the place. The most
interesting part is the ARM guys' virtualized interrupt controller
overhaul, which lets userspace get/set the state and thus enables
migration of ARM VMs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (67 commits)
kvm: make KVM_MMU_AUDIT help text more readable
KVM: s390: Fix memory access error detection
KVM: nVMX: Update guest activity state field on L2 exits
KVM: nVMX: Fix nested_run_pending on activity state HLT
KVM: nVMX: Clean up handling of VMX-related MSRs
KVM: nVMX: Add tracepoints for nested_vmexit and nested_vmexit_inject
KVM: nVMX: Pass vmexit parameters to nested_vmx_vmexit
KVM: nVMX: Leave VMX mode on clearing of feature control MSR
KVM: VMX: Fix DR6 update on #DB exception
KVM: SVM: Fix reading of DR6
KVM: x86: Sync DR7 on KVM_SET_DEBUGREGS
add support for Hyper-V reference time counter
KVM: remove useless write to vcpu->hv_clock.tsc_timestamp
KVM: x86: fix tsc catchup issue with tsc scaling
KVM: x86: limit PIT timer frequency
KVM: x86: handle invalid root_hpa everywhere
kvm: Provide kvm_vcpu_eligible_for_directed_yield() stub
kvm: vfio: silence GCC warning
KVM: ARM: Remove duplicate include
arm/arm64: KVM: relax the requirements of VMA alignment for THP
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
A lot of attention was paid to improving the thin-provisioning target's
handling of metadata operation failures and running out of space. A new
'error_if_no_space' feature was added to allow users to error IOs rather
than queue them when either the data or metadata space is exhausted.
Additional fixes/features include:
- a few fixes to properly support thin metadata device resizing
- a solution for reliably waiting for a DM device's embedded kobject to
be released before destroying the device
- old dm-snapshot is updated to use the dm-bufio interface to take
advantage of readahead capabilities that improve snapshot activation
- new dm-cache target tunables to control how quickly data is promoted
to the cache (fast) device
- improved write efficiency of cluster mirror target by combining
userspace flush and mark requests
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS4GClAAoJEMUj8QotnQNacdEH/2ES5k5itUQRY9jeI+u2zYNP
vdsRTYf+97+B3jpRvpWbMt4kxT2tjaQbkxJ+iKRHy2MBLFUgq8ruH1RS/Q5VbDeg
6i6ol8mpNxhlvo/KTMxXqRcWDSxShiMfhz2lXC2bJ7M4sP/iiH85s4Pm4YQ59jpd
OIX7qj36m/cV/le9YQbexJEEsaj+3genbzL26wyyvtG/rT9fWnXa7clj2gqTdToG
YCEBCRf5FH9X6W/Oc50nMw5n2dt/MRmPre/MAlOjemeaosB0WJiKaswM25rnvHp0
JnhxQ2K2C5KIKAWIfwPOImdb9zWW7p1dIRLsS8nHBUQr0BF5VRkmvpnYH4qBtcc=
=e7e0
-----END PGP SIGNATURE-----
Merge tag 'dm-3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper changes from Mike Snitzer:
"A lot of attention was paid to improving the thin-provisioning
target's handling of metadata operation failures and running out of
space. A new 'error_if_no_space' feature was added to allow users to
error IOs rather than queue them when either the data or metadata
space is exhausted.
Additional fixes/features include:
- a few fixes to properly support thin metadata device resizing
- a solution for reliably waiting for a DM device's embedded kobject
to be released before destroying the device
- old dm-snapshot is updated to use the dm-bufio interface to take
advantage of readahead capabilities that improve snapshot
activation
- new dm-cache target tunables to control how quickly data is
promoted to the cache (fast) device
- improved write efficiency of cluster mirror target by combining
userspace flush and mark requests"
* tag 'dm-3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (35 commits)
dm log userspace: allow mark requests to piggyback on flush requests
dm space map metadata: fix bug in resizing of thin metadata
dm cache: add policy name to status output
dm thin: fix pool feature parsing
dm sysfs: fix a module unload race
dm snapshot: use dm-bufio prefetch
dm snapshot: use dm-bufio
dm snapshot: prepare for switch to using dm-bufio
dm snapshot: use GFP_KERNEL when initializing exceptions
dm cache: add block sizes and total cache blocks to status output
dm btree: add dm_btree_find_lowest_key
dm space map metadata: fix extending the space map
dm space map common: make sure new space is used during extend
dm: wait until embedded kobject is released before destroying a device
dm: remove pointless kobject comparison in dm_get_from_kobject
dm snapshot: call destroy_work_on_stack() to pair with INIT_WORK_ONSTACK()
dm cache policy mq: introduce three promotion threshold tunables
dm cache policy mq: use list_del_init instead of list_del + INIT_LIST_HEAD
dm thin: fix set_pool_mode exposed pool operation races
dm thin: eliminate the no_free_space flag
...
This patch adds a queue mapping mode to the fanout operation of af_packet
sockets. This allows user space af_packet users to better filter on flows
ingressing and egressing via a specific hardware queue, and avoids the potential
packet reordering that can occur when FANOUT_CPU is being used and irq affinity
varies.
Tested successfully by myself. applies to net-next
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the cluster evironment, cluster write has poor performance because
userspace_flush() has to contact a userspace program (cmirrord) for
clear/mark/flush requests. But both mark and flush requests require
cmirrord to communicate the message to all the cluster nodes for each
flush call. This behaviour is really slow.
To address this we now merge mark and flush requests together to reduce
the kernel-userspace-kernel time. We allow a new directive,
"integrated_flush" that can be used to instruct the kernel log code to
combine flush and mark requests when directed by userspace. If not
directed by userspace (due to an older version of the userspace code
perhaps), the kernel will function as it did previously - preserving
backwards compatibility. Additionally, flush requests are performed
lazily when only clear requests exist.
Signed-off-by: Dongmao Zhang <dmzhang@suse.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
improvements when searching resource groups and several updates
to quotas which should increase scalability. The quota changes
follow on from those in the last merge window, and there will
likely be further work to come in this area in due course.
There are also a few patches which help to improve efficiency
of adding entries into directories, and clean up some of that
code.
One on-disk change is included this time, which is to write some
additional information which should be useful to fsck and
also potentially for debugging.
Other than that, its just a few small random bug fixes and
clean ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=/tv0
-----END PGP SIGNATURE-----
Merge tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw
Pull GFS2 updates from Steven Whitehouse:
"The main topics this time are allocation, in the form of Bob's
improvements when searching resource groups and several updates to
quotas which should increase scalability. The quota changes follow on
from those in the last merge window, and there will likely be further
work to come in this area in due course.
There are also a few patches which help to improve efficiency of
adding entries into directories, and clean up some of that code.
One on-disk change is included this time, which is to write some
additional information which should be useful to fsck and also
potentially for debugging.
Other than that, its just a few small random bug fixes and clean ups"
* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw: (24 commits)
GFS2: revert "GFS2: d_splice_alias() can't return error"
GFS2: Small cleanup
GFS2: Don't use ENOBUFS when ENOMEM is the correct error code
GFS2: Fix kbuild test robot reported warning
GFS2: Move quota bitmap operations under their own lock
GFS2: Clean up quota slot allocation
GFS2: Only run logd and quota when mounted read/write
GFS2: Use RCU/hlist_bl based hash for quotas
GFS2: No need to invalidate pages for a dio read
GFS2: Add initialization for address space in super block
GFS2: Add hints to directory leaf blocks
GFS2: For exhash conversion, only one block is needed
GFS2: Increase i_writecount during gfs2_setattr_chown
GFS2: Remember directory insert point
GFS2: Consolidate transaction blocks calculation for dir add
GFS2: Add directory addition info structure
GFS2: Use only a single address space for rgrps
GFS2: Use range based functions for rgrp sync/invalidation
GFS2: Remove test which is always true
GFS2: Remove gfs2_quota_change_host structure
...
It was holiday season, so no wonder that there are little changes in
framework level, although diffstat shows quite many changes spreaded
over sound/* directories. Most of changes are cleanups, code
refactoring and fixes.
Some highlights:
- Removal of OSS sleep_on usages by Arnd
- Simplified memalloc helper codes, drop obsoleted features;
now it's built into PCM driver instead of an individual module
- Warn if PCM buffer preallocation fails, which will show page
allocation issues more clearly
- Compress offload API updates for sample rates by Vinod
- PCM glitch workaround on ctxfi emu20k1 by Sarah
- Drop cs46xx DSP blobs, using firmware loader now
- USB-audio quitks for Plantronics Gamecom 780, Creative VF0420,
and Focusrite Saffire 6
HD-audio specifics:
- Standardize Kconfigs of HD-audio codec drivers;
now "make localmodconfig" recognizes configs properly (finally!)
- Parallel PM implementation by Mengdong
- BayleyBay/ValleyView2 board fixups
- Broadwell audio support
- Runtime PM improvement (PantherPoint, etc)
- Quirks: Dell subwooer, Gigabyte mobo jack detection oddity,
Dell AiO click noise fixes, Dell headset mic fixes, etc
- Automatic bind with HDMI codec parser without generic parser
- More AD codec fixes (since 3.12 regression) including the automatic
stereo mix support
- Common Thinkpad ACPI helper for Realtek and Conexant codecs
ASoC specifics:
- Update to the generic DMA code to support deferred probe and managed
resources
- New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
and Analog Devices AXI I2S and S/PDIF controller IPs
- Device tree support for the simple card, max98090 and cs42l52
- Conversion of the Samsung drivers to native dmaengine, making them
multiplatform compatible and hopefully helping keep them more modern
and up to date.
- More regmap conversions, including a very welcome one for twl6040
from Peter Ujfalusi
- A big overhaul of the DaVinci drivers also from Peter Ujfalusi
- Lots of DMA updates from Lars-Peter
- Improvements to the constraints handling code from Lars-Peter
- A very helpful conversion of the TWL4030 driver to regmap from Peter
- A new driver for the Freescale ESAI controller from Nicolin Chen
- Conversion of some of the drivers to use params_width()
- Extensions to DPCM for use with compressed audio from Liam
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=IWy2
-----END PGP SIGNATURE-----
Merge tag 'sound-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was holiday season, so no wonder that there are little changes in
framework level, although diffstat shows quite many changes spreaded
over sound/* directories. Most of changes are cleanups, code
refactoring and fixes.
Some highlights:
- Removal of OSS sleep_on usages by Arnd
- Simplified memalloc helper codes, drop obsoleted features; now it's
built into PCM driver instead of an individual module
- Warn if PCM buffer preallocation fails, which will show page
allocation issues more clearly
- Compress offload API updates for sample rates by Vinod
- PCM glitch workaround on ctxfi emu20k1 by Sarah
- Drop cs46xx DSP blobs, using firmware loader now
- USB-audio quitks for Plantronics Gamecom 780, Creative VF0420, and
Focusrite Saffire 6
HD-audio specifics:
- Standardize Kconfigs of HD-audio codec drivers; now "make
localmodconfig" recognizes configs properly (finally!)
- Parallel PM implementation by Mengdong
- BayleyBay/ValleyView2 board fixups
- Broadwell audio support
- Runtime PM improvement (PantherPoint, etc)
- Quirks: Dell subwooer, Gigabyte mobo jack detection oddity, Dell
AiO click noise fixes, Dell headset mic fixes, etc
- Automatic bind with HDMI codec parser without generic parser
- More AD codec fixes (since 3.12 regression) including the automatic
stereo mix support
- Common Thinkpad ACPI helper for Realtek and Conexant codecs
ASoC specifics:
- Update to the generic DMA code to support deferred probe and
managed resources
- New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
and Analog Devices AXI I2S and S/PDIF controller IPs
- Device tree support for the simple card, max98090 and cs42l52
- Conversion of the Samsung drivers to native dmaengine, making them
multiplatform compatible and hopefully helping keep them more
modern and up to date.
- More regmap conversions, including a very welcome one for twl6040
from Peter Ujfalusi
- A big overhaul of the DaVinci drivers also from Peter Ujfalusi
- Lots of DMA updates from Lars-Peter
- Improvements to the constraints handling code from Lars-Peter
- A very helpful conversion of the TWL4030 driver to regmap from Peter
- A new driver for the Freescale ESAI controller from Nicolin Chen
- Conversion of some of the drivers to use params_width()
- Extensions to DPCM for use with compressed audio from Liam"
* tag 'sound-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (396 commits)
ASoC: dapm: Fix double prefix addition
ASoC: compress: Add suport for DPCM into compressed audio
ASoC: DPCM: make some DPCM API calls non static for compressed usage
ASoC: core: Fix possible NULL pointer dereference of pcm->config
ALSA: hda - add headset mic detect quirks for some Dell machines
ASoC: tlv320aic32x4: Fix regmap range_min
ASoC: core: Return -ENOTSUPP from set_sysclk() if no operation provided
ASoC: dapm: Change prototype of soc_widget_read
ASoC: samsung: Remove SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag
ASoC: axi-{spdif,i2s}: Remove SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag
ASoC: generic-dmaengine-pcm: Check DMA residue granularity
ASoC: generic-dmaengine-pcm: Check NO_RESIDUE flag at runtime
dma: pl330: Set residue_granularity
dma: Indicate residue granularity in dma_slave_caps
ASoC: simple-card: fix one bug to writing to the platform data
ASoC: pcm: Use snd_pcm_rate_mask_intersect() helper
ALSA: Add helper function for intersecting two rate masks
ASoC: s6000: Don't mix SNDRV_PCM_RATE_CONTINUOUS with specific rates
ASoC: fsl: Don't mix SNDRV_PCM_RATE_CONTINUOUS with specific rates
ASoC: pcm: Properly initialize hw->rate_max
...
Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details are
in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdgc8ACgkQMUfUDdst+ynt9ACguAhrO2WlowdcUZELadTEpqLX
gbkAn0+c1rjizVdIRvs83aQRNJP6w1uR
=oPmD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details
are in the shortlog"
* tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
mei: limit the number of consecutive resets
mei: revamp mei reset state machine
drivers/char: don't use module_init in non-modular ttyprintk.c
VMCI: fix error handling path when registering guest driver
extcon: gpio: Add power resume support
Documentation: HOWTO: Updates on subsystem trees, patchwork, -next (vs. -mm) in ko_KR
Documentation: HOWTO: update for 2.6.x -> 3.x versioning in ko_KR
Documentation: HOWTO: update stable address in ko_KR
Documentation: HOWTO: update LXR web link in ko_KR
char: nwbutton: open-code interruptible_sleep_on
mei: fix syntax in comments and debug output
mei: nfc: mei_nfc_free has to be called under lock
mei: use hbm idle state to prevent spurious resets
mei: do not run reset flow from the interrupt thread
misc: genwqe: fix return value check in genwqe_device_create()
GenWQE: Fix warnings for sparc
GenWQE: Fix compile problems for Alpha
Documentation/misc-devices/mei/mei-amt-version.c: remove unneeded call of mei_deinit()
GenWQE: Rework return code for flash-update ioctl
sgi-xp: open-code interruptible_sleep_on_timeout
...
This is needed for reporting the max GPU engine clock
in OpenCL. This just reports the max possible engine
clock, it does not take into account current conditions
that may limit that clock.
v2: fix query number for merge with 3.13
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull x32 uapi changes from Peter Anvin:
"This is the first few of a set of patches by H.J. Lu to make the
kernel uapi headers usable for x32, as required by some non-glibc
libcs.
These particular patches make the stat and statfs structures usable"
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32: Use __kernel_long_t for __statfs_word
x86, x32: Use __kernel_long_t/__kernel_ulong_t in x86-64 stat.h
Both x32 and x86-64 use the same struct mq_attr for system calls. But
x32 long is 32-bit. This patch replaces long with __kernel_long_t in
struct mq_attr.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/1388182464-28428-9-git-send-email-hjl.tools@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both x32 and x86-64 use the same struct shmid64_ds/shminfo64/shm_info for
system calls. But x32 long is 32-bit. This patch replaces unsigned long
with __kernel_ulong_t in struct shmid64_ds/shminfo64/shm_info.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/1388182464-28428-8-git-send-email-hjl.tools@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both x32 and x86-64 use the same struct msqid64_ds for system calls.
But x32 long is 32-bit. This patch replaces unsigned long with
__kernel_ulong_t in struct msqid64_ds.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/1388182464-28428-6-git-send-email-hjl.tools@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
x32 msgsnd/msgrcv system calls are the same as x86-64 msgsnd/msgrcv system
calls, which use 64-bit integer for long in struct msgbuf . But x32 long
is 32 bit. This patch replaces long in struct msgbuf with __kernel_long_t.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/1388182464-28428-5-git-send-email-hjl.tools@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
x32 IPC system call is the same as x86-64 IPC system call, which uses
64-bit integer for unsigned long in struct ipc64_perm. But x32 long is
32 bit. This patch replaces unsigned long in uapi struct ipc64_perm with
__kernel_ulong_t.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/1388182464-28428-4-git-send-email-hjl.tools@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both x32 and x86-64 use the same struct rusage and struct rlimit for
system calls. But x32 log is 32-bit. This patch change uapi
<linux/resource.h> to use __kernel_long_t in struct rusage and
__kernel_ulong_t in and struct rlimit.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/1388182464-28428-3-git-send-email-hjl.tools@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
