When a shared MSI vector must be used (e.g. when VTd is disabled on
x86_64), each event MSI vector must be set to the shared vector idx.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar<hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The ring element data, though being part of coherent memory, still need
to be performed before updating the ring context to point to this new
element. That can be guaranteed with a memory barrier (dma_wmb).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The c6x architecture was added to the kernel in 2011 at a time when
running Linux on DSPs was widely seen as the logical evolution.
It appears the trend has gone back to running Linux on Arm based SoCs
with DSP, using a better supported software ecosystem, and having better
real-time behavior for the DSP code. An example of this is TI's own
Keystone2 platform.
The upstream kernel port appears to no longer have any users. Mark
Salter remained avaialable to review patches, but mentioned that
he no longer has access to working hardware himself. Without any
users, it's best to just remove the code completely to reduce the
work for cross-architecture code changes.
Many thanks to Mark for maintaining the code for the past ten years.
Link: https://lore.kernel.org/lkml/41dc7795afda9f776d8cd0d3075f776cf586e97c.camel@redhat.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control is
transferred from the middle of the loop, as in the case of a return
or break or goto, there is no decrement thus ultimately resulting in
a memory leak.
Fix a potential memory leak in arm-integrator-lm.c by inserting
of_node_put() before a return statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200829174154.GA9319@Kaladin
Link: https://lore.kernel.org/r/20210112092549.251548-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sunxi_rsb_driver::remove
return void, too. All users already unconditionally return 0, this
commit makes this obvious and ensures future users don't behave
differently. To simplify even further, make axp20x_device_remove()
return void instead of returning 0 unconditionally, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After converting am335x to probe devices with simple-pm-bus I noticed
that we are not passing auxdata for of_platform_populate() like we do
with simple-bus.
While device tree using SoCs should no longer need platform data, there
are still quite a few drivers that still need it as can be seen with
git grep OF_DEV_AUXDATA. We want to have simple-pm-bus be usable as a
replacement for simple-bus also for cases where OF_DEV_AUXDATA is still
needed.
Let's fix the issue by passing auxdata as platform data to simple-pm-bus.
That way the SoCs needing this can pass the auxdata with OF_DEV_AUXDATA.
And let's pass the auxdata for omaps to fix the issue for am335x.
As an alternative solution, adding simple-pm-bus handling directly to
drivers/of/platform.c was considered, but we would still need simple-pm-bus
device driver. So passing auxdata as platform data seems like the simplest
solution.
Fixes: 5a230524f8 ("ARM: dts: Use simple-pm-bus for genpd for am3 l4_wkup")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The fsl_mc_get_endpoint() should return a pointer to the connected
fsl_mc device, if there is one. By interrogating the MC firmware, we
know if there is an endpoint or not so when the endpoint device is
actually searched on the fsl-mc bus and not found we are hitting the
case in which the device has not been yet discovered by the bus.
Return -EPROBE_DEFER so that callers can differentiate this case.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This pointer to an i/o register block is missing the __iomem attribute,
so add it. The issue was found by 0-day sparse run.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20201216161015.29060-1-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gate the clock to save power while the controller is idle.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Since system firmware is likely to use the RSB bus to communicate with a
PMIC while the system is suspended, we cannot make any assumptions about
the controller state after resuming. Thus it is important to completely
reinitialize the controller.
The RSB bus needs to be ready as soon as IRQs are enabled, to handle
wakeup event IRQs coming from the PMIC. Thus it uses NOIRQ callbacks.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This separates the resource acquisition from the hardware initialization
phase, so the hardware initialization can be repeated after system
suspend/resume. The same is done for the exit/remove function, except
that there is no resource deallocation phase due to the use of devres.
The requested RSB clock frequency is stored in `struct sunxi_rsb` so it
will be available when reinitializing the hardware.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
For some reason, this driver's OF match table was placed above the
probe/remove functions, far away from the platform_driver definition.
Adding device PM ops would move the table even farther away. Let's move
it to the usual place, right before the platform_driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
MHI hardware channels are usually the hardware accelerated data path
e.g. IP packets path for modems. This path needs to be optimized for
low latency and high throughput. After several tests on FN980m SDX55
based modem, it seems 1ms is a good default irq_moderation value:
- It allows to reach the maximum download throughput
- It introduces limited latency (5ms is too high)
- It prevents interrupt flooding
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for Diag over MHI. Qualcomm Diag is the qualcomm
diagnostics interface that can be used to collect modem logs,
events, traces, etc. It can be used by tools such QPST or QXDM.
This patch adds the DIAG channels and a dedicated event ring.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
On cold boot, device can take slightly more than 5 seconds to start.
Increase the timeout to prevent MHI power-up issues.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the modem crashes for any reason, we may not be able to detect
it at MHI level (MHI registers not reachable anymore).
This patch implements a health-check mechanism to check regularly
that device is alive (MHI layer can communicate with). If device
is not alive (because a crash or unexpected reset), the recovery
procedure is triggered.
Tested successfully with Telit FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In AER capable root complex, errors are reported to the host which
can then act accordingly and perform PCI recovering procedure.
This patch enables error reporting and implements error_detected,
slot_reset and resume callbacks.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for system wide suspend/resume. During suspend, MHI
device controller must be put in M3 state and PCI bus in D3 state.
Add a recovery procedure allowing to reinitialize the device in case
of error during resume steps, which can happen if device loses power
(and so its context) while system suspend.
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for resetting the device, reset can be triggered in case
of error or manually via sysfs (/sys/bus/pci/devices/*/reset).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Hardware channels have a feature called burst mode that allows to
queue transfer ring element(s) (TRE) to a channel without ringing
the device doorbell. In that mode, the device is polling the channel
context for new elements. This reduces the frequency of host initiated
doorbells and increase throughput.
Create a new dedicated macro for hardware channels with burst enabled.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the IPA (IP hardware accelerator) is starved of event ring elements,
the modem is crashing (SDX55). That can be prevented by setting a
larger number of events (i.e 2 x number of channel ring elements).
Tested with FN980m module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The MHI specification allows to perform a hard reset of the device
when writing to the SOC_RESET register. It can be used to completely
restart the device (e.g. in case of unrecoverable MHI error).
This is up to the MHI controller driver to determine when this hard
reset should be used, and in case of MHI errors, should be used as
a reset of last resort (after standard MHI stack reset).
This function is a stateless function, the MHI layer do nothing except
triggering the reset by writing into the right register(s), this is up
to the caller to ensure right mhi_controller state (e.g. unregister the
controller if necessary).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- enabled GCOV
- reworked setup of protection map
- added support for more MSCC platforms
- added sysfs boardinfo for Loongson64
- enabled KASLR for Loogson64
- added reset controller for BCM63xx
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=0Sht
-----END PGP SIGNATURE-----
Merge tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- enable GCOV
- rework setup of protection map
- add support for more MSCC platforms
- add sysfs boardinfo for Loongson64
- enable KASLR for Loogson64
- add reset controller for BCM63xx
- cleanups and fixes
* tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (70 commits)
mips: fix Section mismatch in reference
MAINTAINERS: Add linux-mips mailing list to JZ47xx entries
MAINTAINERS: Remove JZ4780 DMA driver entry
MAINTAINERS: chenhc@lemote.com -> chenhuacai@kernel.org
MIPS: Octeon: irq: Alloc desc before configuring IRQ
MIPS: mm: Add back define for PAGE_SHARED
MIPS: Select ARCH_KEEP_MEMBLOCK if DEBUG_KERNEL to enable sysfs memblock debug
mips: lib: uncached: fix non-standard usage of variable 'sp'
MIPS: DTS: img: Fix schema warnings for pwm-leds
MIPS: KASLR: Avoid endless loop in sync_icache if synci_step is zero
MIPS: Move memblock_dump_all() to the end of setup_arch()
MIPS: SMP-CPS: Add support for irq migration when CPU offline
MIPS: OCTEON: Don't add kernel sections into memblock allocator
MIPS: Don't round up kernel sections size for memblock_add()
MIPS: Enable GCOV
MIPS: configs: drop unused BACKLIGHT_GENERIC option
MIPS: Loongson64: Fix up reserving kernel memory range
MIPS: mm: Remove unused is_aligned_hugepage_range
MIPS: No need to check CPU 0 in {loongson3,bmips,octeon}_cpu_disable()
mips: cdmm: fix use-after-free in mips_cdmm_bus_discover
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Because the minimum supported DPRC version is 6.0, there is no need to
check for incompatible 6.x versions lower to the minimum one. Just
remove the second half of the check to simplify the logic.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123164839.1668409-1-ciorneiioana@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 197f4d6a4a ("staging: fsl-mc: fsl-mc object allocator driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607068967-31991-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'type' and 'flags' fields were missing from dprc_rsp_get_obj_region
structure therefore the MC Bus driver was not receiving proper flags
from MC like DPRC_REGION_CACHEABLE.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20201124111200.1391-1-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some bootloaders might pause the MC firmware before starting the
kernel to ensure that MC will not cause faults as soon as SMMU
probes due to no configuration being in place for the firmware.
Make sure that MC is resumed at probe time as its SMMU setup should
be done by now.
Also included, a comment fix on how PL and BMT bits are packed in
the StreamID.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20201105153050.19662-2-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch accidentally dropped an error check, so add it back.
Fixes: aef85b56c3 ("bus: fsl-mc: MC control registers are not always available")
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20201105153050.19662-1-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the MHI patch set for v5.11. Most of the patches are cleanups and fixes
but there are some noticeable changes too:
1. Loic finally removed the auto-start option from the channel parameters of the
MHI controller. It is the duty of the client drivers like qrtr to start/stop the
channels when required, so we decided to remove this option. As a side effect,
we changed the qrtr driver to start the channels during its probe and removed
the auto-start option from ath11k controller.
**NOTE** Since these changes spawns both MHI and networking trees, the patches
are maintained in an immutable branch [1] and pulled into both mhi-next and
ath11k-next branches. The networking patches got acks from ath11k and networking
maintainers as well.
2. Loic added a generic MHI pci controller driver. This driver will be used by
the PCI based Qualcomm modems like SDX55 and exposes channels such as QMI,
IP_HW0, IPCR etc...
3. Loic fixed the MHI device hierarchy by maintaining the correct parent child
relationships. Earlier all MHI devices lived in the same level under the parent
device like PCIe. But now, the MHI devices belonging to channels will become the
children of controller MHI device.
4. Finally Loic also improved the MHI device naming by using indexed names such
as mhi0, mhi1, etc... This will break the userspace applications depending on
the old naming convention but since the only one user so far is Jeff Hugo's AI
accelerator apps, we decided to make this change now itself with his agreement.
5. Bhaumik fixed the qrtr driver by stopping the channels during remove. This
patch also got ack from networking maintainer and we decided to take it through
MHI tree (via immutable branch) since we already had a qrtr change.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi.git/log/?h=mhi-ath11k-immutable
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZ6VDKoFIy9ikWCeXVZ8R5v6RzvUFAl/Hwn4ACgkQVZ8R5v6R
zvWCQQgAh7vbwjAvxmzk5OTkuenv9YRV8lYMNTt1zdnXt8k0navv2Tc2M4e6VKbS
WFGCSUCBUQ3wiQ8OZvXVrFMLRm6gramUZEQwn6db7PtcpSUZxoB6w6u/IK5BdD5H
mXUAmJhRP5AUZQ+rWRFpWNAOAzPs6GwfC57KdO44oMuTEyR7FfvNv2X5JaYCbOsM
XBL8aLHFTShdauQREECs3uovaQrBo1BNqMlC+YEdaRhO7ukit4WSeZoEFHS50YSD
nevEJ7R35Cq4s2MQ3gLU5ps5FvRLRoNN5pimy9LUWgq6W/BPGlA7mRIEtDQNu19H
YBlr6G+G/7tvycjxhIkwQ0axmbTrew==
=XZOV
-----END PGP SIGNATURE-----
Merge tag 'mhi-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next
Manivannan writes:
MHI patches for v5.11
Here is the MHI patch set for v5.11. Most of the patches are cleanups and fixes
but there are some noticeable changes too:
1. Loic finally removed the auto-start option from the channel parameters of the
MHI controller. It is the duty of the client drivers like qrtr to start/stop the
channels when required, so we decided to remove this option. As a side effect,
we changed the qrtr driver to start the channels during its probe and removed
the auto-start option from ath11k controller.
**NOTE** Since these changes spawns both MHI and networking trees, the patches
are maintained in an immutable branch [1] and pulled into both mhi-next and
ath11k-next branches. The networking patches got acks from ath11k and networking
maintainers as well.
2. Loic added a generic MHI pci controller driver. This driver will be used by
the PCI based Qualcomm modems like SDX55 and exposes channels such as QMI,
IP_HW0, IPCR etc...
3. Loic fixed the MHI device hierarchy by maintaining the correct parent child
relationships. Earlier all MHI devices lived in the same level under the parent
device like PCIe. But now, the MHI devices belonging to channels will become the
children of controller MHI device.
4. Finally Loic also improved the MHI device naming by using indexed names such
as mhi0, mhi1, etc... This will break the userspace applications depending on
the old naming convention but since the only one user so far is Jeff Hugo's AI
accelerator apps, we decided to make this change now itself with his agreement.
5. Bhaumik fixed the qrtr driver by stopping the channels during remove. This
patch also got ack from networking maintainer and we decided to take it through
MHI tree (via immutable branch) since we already had a qrtr change.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi.git/log/?h=mhi-ath11k-immutable
* tag 'mhi-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi: (30 commits)
mhi: pci_generic: Fix implicit conversion warning
bus: mhi: core: Fix error handling in mhi_register_controller()
bus: mhi: core: Fix device hierarchy
bus: mhi: core: Indexed MHI controller name
net: qrtr: Unprepare MHI channels during remove
bus: mhi: core: Remove MHI event ring IRQ handlers when powering down
bus: mhi: core: Mark and maintain device states early on after power down
bus: mhi: core: Separate system error and power down handling
bus: mhi: core: Check for IRQ availability during registration
bus: mhi: core: Move to an error state on mission mode failure
bus: mhi: core: Use appropriate label in firmware load handler API
bus: mhi: core: Move to an error state on any firmware load failure
bus: mhi: core: Prevent sending multiple RDDM entry callbacks
bus: mhi: core: Move to SYS_ERROR regardless of RDDM capability
bus: mhi: core: Skip device wake in error or shutdown states
bus: mhi: core: Move to using high priority workqueue
bus: mhi: core: Use appropriate names for firmware load functions
bus: mhi: core: Skip RDDM download for unknown execution environment
bus: mhi: core: Rename RDDM download function to use proper words
bus: mhi: core: Remove unused mhi_fw_load_worker() declaration
...
There are a few problems with the error handling in this function. They
mostly center around the alloc_ordered_workqueue() allocation.
1) If that allocation fails or if the kcalloc() prior to it fails then
it leads to a NULL dereference when we call
destroy_workqueue(mhi_cntrl->hiprio_wq).
2) The error code is not set.
3) The "mhi_cntrl->mhi_cmd" allocation is not freed.
The error handling was slightly confusing and I re-ordered it to be in
the exact mirror/reverse order of how things were allocated. I changed
the label names to say what the goto does instead of describing where
the goto comes from.
Fixes: 8f70397876 ("bus: mhi: core: Move to using high priority workqueue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This patch fixes the hierarchical structure of MHI devices. Indeed,
MHI client devices are directly 'enumerated' from the mhi controller
and therefore must be direct descendants/children of their mhi
controller device, in accordance with the Linux Device Model.
Today both MHI clients and controller devices are at the same level,
this patch ensures that MHI controller is parent of its client devices.
The hierarchy is especially important for power management (safe
suspend/resume order). It is also useful for userspace to determine
relationship between MHI client devices and controllers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Today the MHI controller name is simply cloned from the underlying
bus device (its parent), that gives the following device structure
for e.g. a MHI/PCI controller:
devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:02:00.0
devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:02:00.0/0000:02:00.0_IPCR
...
That's quite misleading/confusing and can cause device registering
issues because of duplicate dev name (e.g. if a PCI device register
two different MHI instances).
This patch changes MHI core to create indexed mhi controller names
(mhi0, mhi1...) in the same way as other busses (i2c0, usb0...).
The previous example becomes:
devices/pci0000:00/0000:00:01.2/0000:02:00.0/mhi0
devices/pci0000:00/0000:00:01.2/0000:02:00.0/mhi0/mhi0_IPCR
...
v2: move index field at the end of mhi_controller struct (before bool)
to avoid breaking well packed alignment.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kfree(dev) has been called inside put_device so anther
kfree would cause a use-after-free bug/
Fixes: 8286ae0330 ("MIPS: Add CDMM bus support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
GP Timers used as clockevent/source are not available for ti-sysc bus and
handled by Kernel timekeeping core. Now ti-sysc produces error message
every time such timer is detected:
"ti-sysc: probe of 48040000.target-module failed with error -16"
Such messages are not necessary, so suppress them by returning -ENXIO
instead of -EBUSY.
Fixes: 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While powering down, the device may or may not acknowledge an MHI
RESET issued by host for a graceful shutdown scenario and end up
sending an incoming data packet after tasklets have been killed.
If a rogue device sends this interrupt for a data transfer event
ring update, it can result in a tasklet getting scheduled while a
clean up is ongoing or has completed and cause access to freed
memory leading to a NULL pointer exception. Remove the interrupt
handlers for MHI event rings early on to avoid this scenario.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_power_down() does not ensure that the PM state is moved to an
inaccessible state soon enough as the system can encounter
scheduling delays till mhi_pm_disable_transition() gets called.
Additionally, if an MHI controller decides that the device is now
inaccessible and issues a power down, the register inaccessible
state is not maintained by moving from MHI_PM_LD_ERR_FATAL_DETECT
to MHI_PM_SHUTDOWN_PROCESS. This can result in bus errors if a
client driver attempted to read registers when powering down.
Close these gaps and avoid any race conditions to prevent such
activity.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, there exist a set of if...else statements in the
mhi_pm_disable_transition() function which make handling system
error and disable transitions differently complex. To make that
cleaner and facilitate differences in behavior, separate these
two transitions for MHI host.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Current design allows a controller to register with MHI successfully
without the need to have any IRQs available for use. If no IRQs are
available, power up requests to MHI can fail after a successful
registration with MHI. Improve the design by checking for the number
of IRQs available sooner within the mhi_regsiter_controller() API as
it is required to be specified by the controller.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the host receives a mission mode event and by the time it can get
to processing it, the register accesses fail implying a connectivity
error, MHI should move to an error state. This helps avoid longer wait
times from a synchronous power up perspective and accurately reflects
the MHI execution environment and power management states.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Correct the "error_read" label to say "error_ready_state" as that
is the appropriate usage of the label.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Move MHI to a firmware download error state for a failure to find
the firmware files or to load SBL or EBL image using BHI/BHIe. This
helps detect an error state sooner and shortens the wait for a
synchronous power up timeout.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If an mhi_power_down() is initiated after the device has entered
RDDM and a status callback was provided for it, it is possible
that another BHI interrupt fires while waiting for the MHI
RESET to be cleared. If that happens, MHI host would have moved
a "disabled" execution environment and the check to allow sending
an RDDM status callback will pass when it is should not. Add a
check to see if MHI is in an active state before proceeding.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In some cases, the entry of device to RDDM execution environment
can occur after a significant amount of time has elapsed and a
SYS_ERROR state change event has already arrived. This can result
in scenarios where MHI controller and client drivers are unaware
of the error state of the device. Remove the check for rddm_image
when processing the SYS_ERROR state change as it is present in
mhi_pm_sys_err_handler() already and prevent further activity
until the expected RDDM execution environment change occurs or
the controller driver decides further action.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI client drivers can request a device wake even if the device
may be in an error state or undergoing a shutdown. To prevent
unnecessary device wake processing, check for the device state
and bail out early so that the clients are made aware of the
device state sooner.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
MHI work is currently scheduled on the global/system workqueue and can
encounter delays on a stressed system. To avoid those unforeseen
delays which can hamper bootup or shutdown times, use a dedicated high
priority workqueue instead of the global/system workqueue.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_fw_load_sbl() function is currently used to transfer SBL or EDL
images over BHI (Boot Host Interface). Same goes with mhi_fw_load_amss()
which uses BHIe. However, the contents of these functions do not
indicate support for a specific set of images. Since these can be used
for any image download over BHI or BHIe, rename them based on the
protocol used.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If MHI is unable to determine the execution environment during
the panic path, host must skip the RDDM download. This can happen
if the BHI offset read or the BHI_EXECENV register read fails
indicating that the underlying transport is unresponsive. Hence,
there is no need to trigger an RDDM using SYSERR or request an
SOC reset.
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
mhi_download_rddm_img() uses a shorter version of the word image.
Expand it and rename the function to mhi_download_rddm_image().
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mhi_fw_load_worker() function no longer exists. Remove its
declaration as part of code clean-up.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mhi_get_exec_env() APIs can be used by the controller drivers
to query the execution environment of the MHI device. Expose it
so it can be used in some scenarios to determine behavior of
controllers.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is an extra 'i' counter in the mhi_firmware_copy() function
which is unused. Remove it to clean-up code and reduce stack
space as well as improve efficiency of the function.
Fixes: cd457afb16 ("bus: mhi: core: Add support for downloading firmware over BHIe")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Some MHI device drivers need to stop the channels in their driver
remove callback (e.g. module unloading), but the unprepare function
is aborted because MHI core moved the channels to suspended state
prior calling driver remove callback. This prevents the driver to
send a proper MHI RESET CHAN command to the device. Device is then
unaware of the stopped state of these channels.
This causes issue when driver tries to start the channels again (e.g.
module is reloaded), since device considers channels as already
started (inconsistent state).
Fix this by allowing channel reset when channel is suspended.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Functions parse_ev_cfg() and parse_ch_cfg() access mhi_cntrl->mhi_dev
before it is set in function mhi_register_controller(),
use cntrl_dev instead of mhi_dev.
Fixes: 0cbf260820 ("bus: mhi: core: Add support for registering MHI controllers")
Signed-off-by: Carl Yin <carl.yin@quectel.com>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This is a generic MHI-over-PCI controller driver for MHI only devices
such as QCOM modems. For now it supports registering of Qualcomm SDX55
based PCIe modules. The MHI channels have been extracted from mhi
downstream driver.
This driver is for MHI-only devices which have all functionalities
exposed through MHI channels and accessed by the corresponding MHI
device drivers (no out-of-band communication).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: fixed up the Makefile rule]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The BHI_MSMHWID and BHI_OEMPKHASH macros take a value 'n' which is
a BHI register index. If 'n' is an expression rather than a simple
value, there can be an operator precedence issue which can result
in the incorrect calculation of the register offset. Adding
parentheses around the macro parameter can prevent such issues.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is double acquisition of the pm_lock from mhi_driver_remove()
function. Remove the read_lock_bh/read_unlock_bh calls for pm_lock
taken during a call to mhi_device_put() as the lock is acquired
within the function already. This will help avoid a potential
kernel panic.
Fixes: 189ff97cca ("bus: mhi: core: Add support for data transfer")
Reported-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is really no point having an auto-start for channels.
This is confusing for the device drivers, some have to enable the
channels, others don't have... and waste resources (e.g. pre allocated
buffers) that may never be used.
This is really up to the MHI device(channel) driver to manage the state
of its channels.
While at it, let's also remove the auto-start option from ath11k mhi
controller.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: clubbed ath11k change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We need to enable no-reset-on-init quirk for GPMC if the config
option for CONFIG_OMAP_GPMC_DEBUG is set. Otherwise the GPMC
driver code is unable to show the bootloader configured timings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules like MPU have a powerdomain and functional clock but not
necessarily any control registers. Let's allow configuring interconnect
target modules with no control registers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The rstctrl reset must be asserted after gating the module clock as
described in the TRM at least for IVA. Otherwise the rstctrl reset
done with module clock enabled can hang the system.
Note that this issue is has been only seen with related IVA changes
that we do not currently have merged. So probably no need to apply
this patch as a fix.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This function can be used by client driver to determine whether it's
possible to queue new elements in a channel ring.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604424234-24446-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bail out early from sysc_wait_softreset() just like we do in sysc_reset()
if there's no sysstatus srst_shift to fix a bogus resetdone warning on
enable as suggested by Grygorii Strashko <grygorii.strashko@ti.com>.
We do not currently handle resets for modules that need writing to the
sysstatus register. If we at some point add that, we also need to add
SYSS_QUIRK_RESETDONE_INVERTED flag for cpsw as the sysstatus bit is low
when reset is done as described in the am335x TRM "Table 14-202
SOFT_RESET Register Field Descriptions"
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and
wait for softreset bit") started showing a "OCP softreset timed out"
warning on enable if the interconnect target module is not out of reset.
This caused the warning to be often triggered for i2c and hdq while the
devices are working properly.
Turns out that some interconnect target modules seem to have an unusable
reset status bits unless the module specific reset quirks are activated.
Let's just skip the reset status check for those modules as we only want
to activate the reset quirks when doing a reset, and not on enable. This
way we don't see the bogus "OCP softreset timed out" warnings during boot.
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
Here is the big set of char, misc, and other assorted driver subsystem
patches for 5.10-rc1.
There's a lot of different things in here, all over the drivers/
directory. Some summaries:
- soundwire driver updates
- habanalabs driver updates
- extcon driver updates
- nitro_enclaves new driver
- fsl-mc driver and core updates
- mhi core and bus updates
- nvmem driver updates
- eeprom driver updates
- binder driver updates and fixes
- vbox minor bugfixes
- fsi driver updates
- w1 driver updates
- coresight driver updates
- interconnect driver updates
- misc driver updates
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4g8YQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yngKgCeNpArCP/9vQJRK9upnDm8ZLunSCUAn1wUT/2A
/bTQ42c/WRQ+LU828GSM
=6sO2
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char, misc, and other assorted driver subsystem
patches for 5.10-rc1.
There's a lot of different things in here, all over the drivers/
directory. Some summaries:
- soundwire driver updates
- habanalabs driver updates
- extcon driver updates
- nitro_enclaves new driver
- fsl-mc driver and core updates
- mhi core and bus updates
- nvmem driver updates
- eeprom driver updates
- binder driver updates and fixes
- vbox minor bugfixes
- fsi driver updates
- w1 driver updates
- coresight driver updates
- interconnect driver updates
- misc driver updates
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (396 commits)
binder: fix UAF when releasing todo list
docs: w1: w1_therm: Fix broken xref, mistakes, clarify text
misc: Kconfig: fix a HISI_HIKEY_USB dependency
LSM: Fix type of id parameter in kernel_post_load_data prototype
misc: Kconfig: add a new dependency for HISI_HIKEY_USB
firmware_loader: fix a kernel-doc markup
w1: w1_therm: make w1_poll_completion static
binder: simplify the return expression of binder_mmap
test_firmware: Test partial read support
firmware: Add request_partial_firmware_into_buf()
firmware: Store opt_flags in fw_priv
fs/kernel_file_read: Add "offset" arg for partial reads
IMA: Add support for file reads without contents
LSM: Add "contents" flag to kernel_read_file hook
module: Call security_kernel_post_load_data()
firmware_loader: Use security_post_load_data()
LSM: Introduce kernel_post_load_data() hook
fs/kernel_read_file: Add file_size output argument
fs/kernel_read_file: Switch buffer size arg to size_t
fs/kernel_read_file: Remove redundant size argument
...
There are several occurrences of the following pattern:
for_each_memblock(memory, reg) {
start = __pfn_to_phys(memblock_region_memory_base_pfn(reg);
end = __pfn_to_phys(memblock_region_memory_end_pfn(reg));
/* do something with start and end */
}
Using for_each_mem_range() iterator is more appropriate in such cases and
allows simpler and cleaner code.
[akpm@linux-foundation.org: fix arch/arm/mm/pmsa-v7.c build]
[rppt@linux.ibm.com: mips: fix cavium-octeon build caused by memblock refactoring]
Link: http://lkml.kernel.org/r/20200827124549.GD167163@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Emil Renner Berthing <kernel@esmil.dk>
Cc: Hari Bathini <hbathini@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: https://lkml.kernel.org/r/20200818151634.14343-13-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The region size reported by the firmware for mc and software
portals was less than allocated by the hardware. This may be
problematic when mmapping the region in user space because the
region size is less than page size. However the size as reserved
by the hardware is 64K.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-14-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In virtual machines the device-id range is defined
between 0x10000-0x20000. The reason for using such a
large range is to avoid overlapping with the PCI range.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-13-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ pool handling functions can be used by both DPRC
driver and VFIO. Adapt and export those functions.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-12-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before destroying the mc_io, check first that it was
allocated.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-11-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both DPRC driver and VFIO driver use the same initialization code
for the DPRC. Introduced a new function which groups this
initialization code. The function is exported and may be
used by VFIO as well.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-10-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create and export a cleanup function for DPRC. The function
is used by the DPRC driver, but it will be used by the VFIO
driver as well.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-9-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the DPRC scan function is used only by the bus driver.
But the same functionality will be needed by the VFIO driver.
To support this, the dprc scan function was exported and a little
bit adjusted to fit both scenarios. Also the scan mutex initialization
is done when the bus object is created, not in dprc_probe in order
to be used by both VFIO and bus driver.
Similarily dprc_remove_devices is exported to be used by VFIO.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-8-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are already firmware API commands that have multiple
versions. For each multiple version command, another command
to retrieve the API version is issued. This may introduce an important
overhead. The version does not change while the system is running,
so the DPRC API version can be safely cached.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-6-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QMAN region is memory mapped, so it should be of type
IORESOURCE_MEM. The region flags bits were wrongly used to
pass additional information. Use the bus specific bits for
this purpose.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-5-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is required for vfio-fsl-mc meta driver to successfully bind
layerscape container devices for device passthrough. This patch adds
a mechanism to allow a layerscape device to specify a driver rather than
a layerscape driver provide a device match.
Example to allow a device (dprc.1) to specifically bind
with driver (vfio-fsl-mc):-
- echo vfio-fsl-mc > /sys/bus/fsl-mc/devices/dprc.1/driver_override
- echo dprc.1 > /sys/bus/fsl-mc/drivers/fsl_mc_dprc/unbind
- echo dprc.1 > /sys/bus/fsl-mc/drivers/vfio-fsl-mc/bind
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-4-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare the dprc_scan_objects function to be used by
the VFIO mc driver code. The function is used to scan the mc
objects by the bus driver. The same functionality is
needed by the VFIO mc driver, but in this case the
interrupt configuration is delayed until the userspace
configures the interrupts. In order to use the same function
in both drivers add a new parameter.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-3-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The total number of interrupts is only used for some checks
outside the dprc_scan_objects function. Furthermore, in some
situations the check is made twice. Move the bounds check inside
the function for all situations.
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Link: https://lore.kernel.org/r/20200929085441.17448-2-diana.craciun@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the device tree binding, in certain scenarios such as
virtualization scenarios, the MC control registers are not
available so don't error out if they are not present.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200914105459.27448-2-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are certain scenarios where an iommu is not present, e.g.
booting in a VM. Let's support these scenarios by dropping the
check.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200914105459.27448-1-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kbuild rule to build MHI should use the append operator. This fixes
the below warning reported by Kbuild test bot.
WARNING: modpost: missing MODULE_LICENSE() in
drivers/bus/mhi/core/main.o
WARNING: modpost: missing MODULE_LICENSE() in drivers/bus/mhi/core/pm.o
WARNING: modpost: missing MODULE_LICENSE() in
drivers/bus/mhi/core/boot.o
Fixes: 0cbf260820 ("bus: mhi: core: Add support for registering MHI controllers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-19-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no requirement for using a dedicated IRQ per event ring.
Some systems does not support multiple MSI vectors (e.g. intel
without CONFIG_IRQ_REMAP), In that case the MHI controller can
configure all the event rings to use the same interrupt (as fallback).
Allow this by removing the nr_irqs = ev_ring test and add extra check
in the irq_setup function.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-17-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce sysfs entries to enable userspace clients the ability to read
the serial number and the OEM PK Hash values obtained from BHI. OEMs
need to read these device-specific hardware information values through
userspace for factory testing purposes and cannot be exposed via degbufs
as it may remain disabled for performance reasons. Also, update the
documentation for ABI to include these entries.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: used dev_groups to manage sysfs attributes]
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-16-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce debugfs entries to show state, register, channel, device,
and event rings information. Allow the host to dump registers,
issue device wake, and change the MHI timeout to help in debug.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kconfig coding style mandates use of tabs for the configuration
definition and an additional two spaces for the help text. Make the
required changes to the MHI Kconfig adhering to those guidelines.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI channel, event and controller config data needs to be
treated read only information. Add const qualifier to make
sure config information passed by MHI controller is not
modified by MHI core driver.
Suggested-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Client devices should use the APIs provided to allocate and free
the MHI controller structure. This will help ensure that the
structure is zero-initialized and there are no false positives
with respect to reading any values such as the serial number or
the OEM PK hash.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device hardware specific information such as serial number and the OEM
PK hash can be read using BHI and saved on host to identify the
endpoint.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use counters to track MHI device state transitions such as those
to M0, M2, or M3 states. This can help in better debug, allowing
the user to see the number of transitions to a certain MHI state
when queried using debugfs entries or via other mechanisms.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a helper function to determine whether the device is in a
powered ON state and resides in one of the active MHI states. This will
allow for some use cases where access can be pre-determined.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An MHI device is not necessarily associated with only channels as we can
have one associated with the controller itself. Hence, the chan_name
field within the mhi_device structure should instead be replaced with a
generic name to accurately reflect any type of MHI device.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that the host may be suspending or suspended and may
not allow an outgoing device wake assert immediately if a client has
requested for it. Ensure that the host wakes up and allows for it so
the client does not have to wait for an external trigger or an
outgoing packet to be queued for the host resume to occur.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Autonomous low power mode support requires the MHI host to resume from
multiple places and post a wakeup source to exit system suspend. This
needs to be done in a non-blocking manner. Introduce a helper API to
trigger the host resume for data transfers and other non-blocking use
cases while supporting implementation of autonomous low power modes.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing check to abort suspends if a client driver has pending
outgoing packets to send to the device. This allows better utilization
of the MHI bus wherein clients on the host are not left waiting for
longer suspend or resume cycles to finish for data transfers.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200929175218.8178-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GISB breakpoint interrupts can be raised when a breakpoint has been
enabled to match a specific master and/or GISB register address. Being
able to print a message, similar to those done during target abort or
timeout greatly helps debug systems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Do not print the full function name (brcmstb_gisb_arb_decode_addr) which
is quite long, and reduces our chances to printing a full line, instead
just use "GISB: " as a prefix for these prints.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- improvements for Loongson64
- extended ingenic support
- removal of not maintained paravirt system type
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=I/vU
-----END PGP SIGNATURE-----
Merge tag 'mips_5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS upates from Thomas Bogendoerfer:
- improvements for Loongson64
- extended ingenic support
- removal of not maintained paravirt system type
- cleanups and fixes
* tag 'mips_5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (81 commits)
MIPS: SGI-IP27: always enable NUMA in Kconfig
MAINTAINERS: Update KVM/MIPS maintainers
MIPS: Update default config file for Loongson-3
MIPS: KVM: Add kvm guest support for Loongson-3
dt-bindings: mips: Document Loongson kvm guest board
MIPS: handle Loongson-specific GSExc exception
MIPS: add definitions for Loongson-specific CP0.Diag1 register
MIPS: only register FTLBPar exception handler for supported models
MIPS: ingenic: Hardcode mem size for qi,lb60 board
MIPS: DTS: ingenic/qi,lb60: Add model and memory node
MIPS: ingenic: Use fw_passed_dtb even if CONFIG_BUILTIN_DTB
MIPS: head.S: Init fw_passed_dtb to builtin DTB
of: address: Fix parser address/size cells initialization
of_address: Guard of_bus_pci_get_flags with CONFIG_PCI
MIPS: DTS: Fix number of msi vectors for Loongson64G
MIPS: Loongson64: Add ISA node for LS7A PCH
MIPS: Loongson64: DTS: Fix ISA and PCI I/O ranges for RS780E PCH
MIPS: Loongson64: Enlarge IO_SPACE_LIMIT
MIPS: Loongson64: Process ISA Node in DeviceTree
of_address: Add bus type match for pci ranges parser
...
Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXylccQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymofgCfZ1CxNWd0ZVM0YIn8cY9gO6ON7MsAnRq48hvn
Vjf4rKM73GC11bVF4Gyy
=Xq1R
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (322 commits)
habanalabs: remove unused but set variable 'ctx_asid'
nvmem: qcom-spmi-sdam: Enable multiple devices
dt-bindings: nvmem: SID: add binding for A100's SID controller
nvmem: update Kconfig description
nvmem: qfprom: Add fuse blowing support
dt-bindings: nvmem: Add properties needed for blowing fuses
dt-bindings: nvmem: qfprom: Convert to yaml
nvmem: qfprom: use NVMEM_DEVID_AUTO for multiple instances
nvmem: core: add support to auto devid
nvmem: core: Add nvmem_cell_read_u8()
nvmem: core: Grammar fixes for help text
nvmem: sc27xx: add sc2730 efuse support
nvmem: Enforce nvmem stride in the sysfs interface
MAINTAINERS: Add git tree for NVMEM FRAMEWORK
nvmem: sprd: Fix return value of sprd_efuse_probe()
drivers: android: Fix the SPDX comment style
drivers: android: Fix a variable declaration coding style issue
drivers: android: Remove braces for a single statement if-else block
drivers: android: Remove the use of else after return
drivers: android: Fix a variable declaration coding style issue
...
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
- Removal of the tremendously unpopular read_barrier_depends() barrier,
which is a NOP on all architectures apart from Alpha, in favour of
allowing architectures to override READ_ONCE() and do whatever dance
they need to do to ensure address dependencies provide LOAD ->
LOAD/STORE ordering. This work also offers a potential solution if
compilers are shown to convert LOAD -> LOAD address dependencies into
control dependencies (e.g. under LTO), as weakly ordered architectures
will effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic, augment
the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the device
ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions and
kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words.
-----BEGIN PGP SIGNATURE-----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=mh79
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 and cross-arch updates from Catalin Marinas:
"Here's a slightly wider-spread set of updates for 5.9.
Going outside the usual arch/arm64/ area is the removal of
read_barrier_depends() series from Will and the MSI/IOMMU ID
translation series from Lorenzo.
The notable arm64 updates include ARMv8.4 TLBI range operations and
translation level hint, time namespace support, and perf.
Summary:
- Removal of the tremendously unpopular read_barrier_depends()
barrier, which is a NOP on all architectures apart from Alpha, in
favour of allowing architectures to override READ_ONCE() and do
whatever dance they need to do to ensure address dependencies
provide LOAD -> LOAD/STORE ordering.
This work also offers a potential solution if compilers are shown
to convert LOAD -> LOAD address dependencies into control
dependencies (e.g. under LTO), as weakly ordered architectures will
effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at
LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic,
augment the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the
device ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions
and kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words"
Link: http://lkml.kernel.org/r/20200710165203.31284-1-will@kernel.org
Link: http://lkml.kernel.org/r/20200619082013.13661-1-lorenzo.pieralisi@arm.com
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (82 commits)
arm64: use IRQ_STACK_SIZE instead of THREAD_SIZE for irq stack
arm64/mm: save memory access in check_and_switch_context() fast switch path
arm64: sigcontext.h: delete duplicated word
arm64: ptrace.h: delete duplicated word
arm64: pgtable-hwdef.h: delete duplicated words
bus: fsl-mc: Add ACPI support for fsl-mc
bus/fsl-mc: Refactor the MSI domain creation in the DPRC driver
of/irq: Make of_msi_map_rid() PCI bus agnostic
of/irq: make of_msi_map_get_device_domain() bus agnostic
dt-bindings: arm: fsl: Add msi-map device-tree binding for fsl-mc bus
of/device: Add input id to of_dma_configure()
of/iommu: Make of_map_rid() PCI agnostic
ACPI/IORT: Add an input ID to acpi_dma_configure()
ACPI/IORT: Remove useless PCI bus walk
ACPI/IORT: Make iort_msi_map_rid() PCI agnostic
ACPI/IORT: Make iort_get_device_domain IRQ domain agnostic
ACPI/IORT: Make iort_match_node_callback walk the ACPI namespace for NC
arm64: enable time namespace support
arm64/vdso: Restrict splitting VVAR VMA
arm64/vdso: Handle faults on timens page
...
Add ACPI support in the fsl-mc driver. Driver parses MC DSDT table to
extract memory and other resources.
Interrupt (GIC ITS) information is extracted from the MADT table
by drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c.
IORT table is parsed to configure DMA.
Signed-off-by: Makarand Pawagi <makarand.pawagi@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200619082013.13661-13-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The DPRC driver is not taking into account the msi-map property
and assumes that the icid is the same as the stream ID. Although
this assumption is correct, generalize the code to include a
translation between icid and streamID.
Furthermore do not just copy the MSI domain from parent (for child
containers), but use the information provided by the msi-map property.
If the msi-map property is missing from the device tree retain the old
behaviour for backward compatibility ie the child DPRC objects
inherit the MSI domain from the parent.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200619082013.13661-12-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Devices sitting on proprietary busses have a device ID space that
is owned by the respective bus and related firmware bindings. In order
to let the generic OF layer handle the input translations to
an IOMMU id, for such busses the current of_dma_configure() interface
should be extended in order to allow the bus layer to provide the
device input id parameter - that is retrieved/assigned in bus
specific code and firmware.
Augment of_dma_configure() to add an optional input_id parameter,
leaving current functionality unchanged.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200619082013.13661-8-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=7P/h
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull timer fix from Ingo Molnar:
"Fix a suspend/resume regression (crash) on TI AM3/AM4 SoC's"
* tag 'timers-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4
Because the DPNIs are probed before DPMCPs and other objects that need
to be allocated, messages like "No more resources of type X left" are
printed by the fsl-mc bus driver. This patch resolves the issue by probing
the allocatable objects first and then any other object that may use
them.
Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200717154800.17169-4-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the spinlock that serializes the MC commands with a raw
spinlock. This is needed for the RT kernel because there are MC
commands sent in interrupt context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200717154800.17169-3-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MC bus has different types of devices that can be discovered on the
bus. Add the missing device types.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200717154800.17169-2-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Carlos Hernandez <ceh@ti.com> reported that we now have a suspend and
resume regresssion on am3 and am4 compared to the earlier kernels. While
suspend and resume works with v5.8-rc3, we now get errors with rtcwake:
pm33xx pm33xx: PM: Could not transition all powerdomains to target state
...
rtcwake: write error
This is because we now fail to idle the system timer clocks that the
idle code checks and the error gets propagated to the rtcwake.
Turns out there are several issues that need to be fixed:
1. Ignore no-idle and no-reset configured timers for the ti-sysc
interconnect target driver as otherwise it will keep the system timer
clocks enabled
2. Toggle the system timer functional clock for suspend for am3 and am4
(but not for clocksource on am3)
3. Only reconfigure type1 timers in dmtimer_systimer_disable()
4. Use of_machine_is_compatible() instead of of_device_is_compatible()
for checking the SoC type
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200713162601.6829-1-tony@atomide.com
CDMM may be available not only on MIPS R2 architectures, but also on
newer MIPS R5 chips. For instance our P5600 chip has one. Let's mark
the CDMM bus being supported for that MIPS arch too.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Since having and mapping the CDMM block is platform specific, then
instead of just returning a zero-address, lets make the default CDMM
base address search method (mips_cdmm_phys_base()) to do something
useful. For instance to find the address in a dedicated dtb-node in
order to support of-based platforms by default.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Similar to what we have for the legacy platform data, we need to
configure SWSUP_SIDLE and SWSUP_MSTANDBY quirks for usb_host_hs.
These are needed to drop the legacy platform data for usb_host_hs.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we have "ti,no-idle" specified for a module we must not disable
the the module on suspend to keep things backwards compatible.
Fixes: 386cb76681 ("bus: ti-sysc: Handle missed no-idle property in addition to no-idle-on-init")
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_DEBUG_ATOMIC_SLEEP enabled we can see the following with RTC probe:
BUG: sleeping function called from invalid context at drivers/bus/ti-sysc.c:1736
...
(sysc_quirk_rtc) from [<c060d01c>] (sysc_write_sysconfig+0x1c/0x60)
(sysc_write_sysconfig) from [<c060d9f4>] (sysc_enable_module+0x11c/0x274)
(sysc_enable_module) from [<c060f37c>] (sysc_probe+0xe9c/0x1380)
(sysc_probe) from [<c06e9384>] (platform_drv_probe+0x48/0x98)
Fixes: e8639e1c98 ("bus: ti-sysc: Handle module unlock quirk needed for some RTC")
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_DEBUG_ATOMIC_SLEEP enabled we can see the following with
wakeirqs and serial console idled:
BUG: sleeping function called from invalid context at drivers/bus/ti-sysc.c:242
...
(sysc_wait_softreset) from [<c0606894>] (sysc_enable_module+0x48/0x274)
(sysc_enable_module) from [<c0606c5c>] (sysc_runtime_resume+0x19c/0x1d8)
(sysc_runtime_resume) from [<c0606cf0>] (sysc_child_runtime_resume+0x58/0x84)
(sysc_child_runtime_resume) from [<c06eb7bc>] (__rpm_callback+0x30/0x12c)
(__rpm_callback) from [<c06eb8d8>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c06eb434>] (rpm_resume+0x638/0x7fc)
(rpm_resume) from [<c06eb658>] (__pm_runtime_resume+0x60/0x9c)
(__pm_runtime_resume) from [<c06edc08>] (handle_threaded_wake_irq+0x24/0x60)
(handle_threaded_wake_irq) from [<c01befec>] (irq_thread_fn+0x1c/0x78)
(irq_thread_fn) from [<c01bf30c>] (irq_thread+0x140/0x26c)
We have __pm_runtime_resume() call the sysc_runtime_resume() with spinlock
held and interrupts disabled.
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
-----BEGIN PGP SIGNATURE-----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=fT9A
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit 636338d796.
This patch is not a proper fixes the i2c2 timeouts are still
happening in some cases.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Otherwise we can get "OCP softreset timed out" warnings occasionally
at least for i2c2 on omap4 now that we check the OCP softreset completed
bit on enable.
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently only setting the framedonetv_irq disabled for the SoCs
that don't have it. But we are never setting it enabled for the SoCs that
have it. Let's initialized it to true by default.
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must ignore the clockactivity bit for most modules and not set it
unless specified for the module with SYSC_QUIRK_USE_CLOCKACT. Otherwise
the interface clock can be automatically gated constantly causing
unexpected performance issues.
Fixes: ae9ae12e9d ("bus: ti-sysc: Handle clockactivity for enable and disable")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules reset automatically when idled, and when re-enabled, we must
wait for the automatic OCP softreset to complete. And if optional clocks
are configured, we need to keep the clocks on while waiting for the reset
to complete.
Let's fix the issue by moving the OCP softreset code to a separate
function sysc_wait_softreset(), and call it also from sysc_enable_module()
with the optional clocks enabled.
This is based on what we're already doing for legacy platform data booting
in _enable_sysc().
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we're missing flush of posted write after module enable and
disable. I've seen occasional errors accessing various modules, and it
is suspected that the lack of posted writes can also cause random reboots.
The errors we can see are similar to the one below from spi for example:
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read): Data Access
in User mode during Functional access
...
mcspi_wait_for_reg_bit
omap2_mcspi_transfer_one
spi_transfer_one_message
...
We also want to also flush posted write for disable. The clkctrl clock
disable happens after module disable, and we don't want to have the
module potentially stay active while we're trying to disable the clock.
Fixes: d59b60564c ("bus: ti-sysc: Add generic enable/disable functions")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Alas the method trigger_all_cpu_backtrace() isn't exported by the
kernel, but we need to have it called in case of the bus errors detected
to get a better description of a possible cause of the error. Let's
disable the ability to build the driver as a loadable kernel module then.
Note In future the driver will support the AXI-bus interconnect capability,
so we'd have to make it built into the kernel anyway.
Link: https://lore.kernel.org/r/20200528193113.17372-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Seeing trigger_all_cpu_backtrace() isn't exported from the kernel and
since calling it is a very important part of driver, which may provide
a better description of a possible cause of the error, let's disable the
ability to build the driver as a loadable kernel module.
Link: https://lore.kernel.org/r/20200528193113.17372-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is a ready-to-use method to compare a retrieved from a sysfs node
string with another string. It treats both NUL and newline-then-NUL as
equivalent string terminations. So use it instead of manually truncating
the line length in the strncmp() method.
Link: https://lore.kernel.org/r/20200528145050.5203-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It's better to have a single return statement where it's applicable
instead of returning from a conditional statement if-clause. Let's
do this in the request registers, clock and IRQ methods.
Link: https://lore.kernel.org/r/20200528145050.5203-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is a ready-to-use method to compare a retrieved from a sysfs node
string with another string. It treats both NUL and newline-then-NUL as
equivalent string terminations. So use it instead of manually truncating
the line length in the strncmp() method.
Link: https://lore.kernel.org/r/20200528145050.5203-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Indeed it's more optimal to use the PTR_ERR_OR_ZERO() macro there instead
of having two return points.
Link: https://lore.kernel.org/r/20200528145050.5203-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After fixing the sysfs calback return value the functions argumnets
identations have been left as before the fix. That made the
argments declarations being unaligned with respect to the space
surrounded by the parentheses.
Link: https://lore.kernel.org/r/20200528145050.5203-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It must be included since we are using readl() method here.
Link: https://lore.kernel.org/r/20200528145050.5203-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Baikal-T1 AXI-APB bridge is used to access the SoC subsystem CSRs.
IO requests are routed to this bus by means of the DW AMBA 3 AXI
Interconnect. In case if an attempted APB transaction stays with no
response for a pre-defined time an interrupt occurs and the bus gets
freed for a next operation. This driver provides the interrupt handler
to detect the erroneous address, prints an error message about the
address fault, updates an errors counter. The counter and the APB-bus
operations timeout can be accessed via corresponding sysfs nodes.
A dedicated sysfs-node can be also used to artificially cause the
bus errors described above.
[arnd: fix build warnings for missing includes and wrong return types]
Link: https://lore.kernel.org/r/20200526125928.17096-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: soc@kernel.org
Cc: devicetree@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AXI3-bus is the main communication bus connecting all high-speed
peripheral IP-cores with RAM controller and MIPS P5600 cores on Baikal-T1
SoC. Bus traffic arbitration is done by means of DW AMBA 3 AXI
Interconnect (so called AXI Main Interconnect) routing IO requests from
one SoC block to another. This driver provides a way to detect any bus
protocol errors and device not responding situations by means of an
embedded on top of the interconnect errors handler block (EHB). AXI
Interconnect QoS arbitration tuning is currently unsupported.
The bus doesn't provide a way to detect the interconnected devices,
so they are supposed to be statically defined like by means of the
simple-bus sub-nodes.
[arnd: fix build warnings for missing includes and wrong return types]
Link: https://lore.kernel.org/r/20200526125928.17096-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: soc@kernel.org
Cc: devicetree@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
-----BEGIN PGP SIGNATURE-----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=07SB
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
System timer changes for omaps for v5.8 merge window
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
* tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
ARM: dts: Configure system timers for omap3
ARM: dts: Configure system timers for omap5 and dra7
ARM: dts: Configure system timers for omap4
ARM: dts: Configure system timers for am437x
ARM: dts: Configure system timers for am335x
ARM: OMAP2+: Add omap_init_time_of()
bus: ti-sysc: Ignore timer12 on secure omap3
clk: ti: dm816: enable sysclk6_ck on init
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
Link: https://lore.kernel.org/r/pull-1590169577-735045@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The MHI device may be in the syserr state when we attempt to init it in
power_up(). Since we have no local state, the handling is simple -
reset the device and wait for it to transition out of the reset state.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take write lock only to protect db_mode member of mhi channel.
This allows rest of the mhi channels to just take read lock which
fine grains the locking. It prevents channel readers to starve if
they try to enter critical section after a writer.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices that support RDDM do not require processing SYS_ERROR as it is
deemed redundant. Avoid SYS_ERROR processing if RDDM is supported by
the device.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver continues handling of BHI interrupt even if MHI register access
is not allowed. By doing so it calls the status call back and performs
early notification for the MHI client. This is not needed when MHI
register access is not allowed. Hence skip the handling in this case and
return. Also add debug log to print device state, local EE and device EE
when reg access is valid.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mission mode transition is handled by state worker thread but
power off is not. There is a possibility while mission mode
transition is in progress which calls MHI client driver probe,
power off is issued by MHI controller. This results into client
driver probe and remove running in parallel and causes use after
free situation. By queuing disable transition work when mission
mode is in progress prevents the race condition.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the system error worker thread and instead have the
execution environment worker handle that transition to serialize
processing and avoid any possible race conditions during
shutdown.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While writing any sequence or session identifiers, it is possible that
the host could write a zero value, whereas only non-zero values should
be supported writes to those registers. Ensure that the host does not
write a non-zero value for them and also log them in debug messages. A
macro is introduced to simplify this check and the existing checks are
also converted to use this macro.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading AMSS firmware using BHIe protocol, return -ETIMEDOUT if no
response is received within the timeout or return -EIO in case of a
protocol returned failure or an MHI error state.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon power up, driver queues firmware worker thread if the execution
environment is PBL. Firmware worker is blocked with a timeout until
state worker gets a chance to run and unblock firmware worker. An
endpoint power up failure can be seen if state worker gets a chance to
run after firmware worker has timed out. Remove this dependency and
handle firmware load directly using state worker thread.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MHI Driver receives an EOT event, it reads xfer_len from the
event in the last TRE. The value is under control of the MHI device
and never validated by Host MHI driver. The value should never be
larger than the real size of the buffer but a malicious device can
set the value 0xFFFF as maximum. This causes driver to memory
overflow (both read or write). Fix this issue by reading minimum of
transfer length from event and the buffer length provided.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI data completion handler function reads channel id from event
ring element. Value is under the control of MHI devices and can be
any value between 0 and 255. In order to prevent out of bound access
add a bound check against the max channel supported by controller
and skip processing of that event ring element.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver is using zero initialized intmod value from mhi channel when
configuring TRE for bei field. This prevents interrupt moderation to
take effect in case it is supported by an event ring. Fix this by
copying intmod value from associated event ring to mhi channel upon
registering mhi controller.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all the common code to generate TRE from mhi_queue_buf,
mhi_queue_dma and mhi_queue_skb to mhi_gen_tre. This helps
to centralize the TRE generation code which makes any future
bug fixing easier to manage in these APIs.
Suggested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As timers no longer need legacy quirk handling, let's move them to
the CONFIG_DEBUG section to make it easier to see which drivers still
need more work.
Let's also add detection for few more older timer revisions while at
it as that makes CONFIG_DEBUG output easier to read with proper names.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some early omap3 boards use timer12 for system timer, but for secure
SoCs like on n900 it's not accessible. Likely we will be configuring
unavailable devices for other SoCs too based on runtime SoC detection,
so let's use a switch to start with.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series enables building various Versatile Express platform drivers
as modules. The primary target is the Fast Model FVP which is supported
in Android. As Android is moving towards their GKI, or generic kernel,
the hardware support has to be in modules. Currently ARCH_VEXPRESS
enables several built-in only drivers. Some of these are needed, but
some are only needed for older 32-bit VExpress platforms and can just
be disabled.
-----BEGIN PGP SIGNATURE-----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=c5eS
-----END PGP SIGNATURE-----
Merge tag 'vexpress-modules-for-soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into arm/soc
VExpress modularization
This series enables building various Versatile Express platform drivers
as modules. The primary target is the Fast Model FVP which is supported
in Android. As Android is moving towards their GKI, or generic kernel,
the hardware support has to be in modules. Currently ARCH_VEXPRESS
enables several built-in only drivers. Some of these are needed, but
some are only needed for older 32-bit VExpress platforms and can just
be disabled.
* tag 'vexpress-modules-for-soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: vexpress: Don't select VEXPRESS_CONFIG
bus: vexpress-config: Support building as module
vexpress: Move setting master site to vexpress-config bus
bus: vexpress-config: simplify config bus probing
bus: vexpress-config: Merge vexpress-syscfg into vexpress-config
mfd: vexpress-sysreg: Support building as a module
mfd: vexpress-sysreg: Use devres API variants
mfd: vexpress-sysreg: Drop unused syscon child devices
mfd: vexpress-sysreg: Drop selecting CONFIG_CLKSRC_MMIO
clk: vexpress-osc: Support building as a module
clk: vexpress-osc: Use the devres clock API variants
clk: versatile: Only enable SP810 on 32-bit by default
clk: versatile: Rework kconfig structure
amba: Retry adding deferred devices at late_initcall
arm64: vexpress: Don't select CONFIG_POWER_RESET_VEXPRESS
ARM: vexpress: Move vexpress_flags_set() into arch code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix to return negative error code from the error handling case
instead of 0 in mhi_init_dev_ctxt() and mhi_driver_probe().
Fixes: 3000f85b8f ("bus: mhi: core: Add support for basic PM operations")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200509075654.175002-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's only a single caller of vexpress_config_set_master() from
vexpress-sysreg.c. Let's just make the registers needed available to
vexpress-config and move all the code there. The registers needed aren't
used anywhere else either. With this, we can get rid of the private API
between these 2 drivers.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The vexpress-config initialization is dependent on the vexpress-syscfg
driver probing. As vexpress-config was not a driver, deferred probe
could not be used and instead initcall ordering was relied upon. This is
fragile and doesn't work for modules.
Let's move the config bus init into the vexpress-syscfg probe. This
eliminates the initcall ordering requirement and the need to create a
struct device and the "vexpress-config" class.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The only thing that vexpress-syscfg does is provide a regmap to
vexpress-config bus child devices. There's little reason to have 2
components for this. The current structure with initcall ordering
requirements makes turning these components into modules more difficult.
So let's start to simplify things and merge vexpress-syscfg into
vexpress-config. There's no functional change in this commit and it's
still separate components until subsequent commits.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When multiple instances of the same MHI product are present in a system,
we can see a splat from mhi_create_devices() - "sysfs: cannot create
duplicate filename".
This is because the device names assigned to the MHI channel devices are
non-unique. They consist of the channel's name, and the channel's pipe
id. For identical products, each instance is going to have the same
set of channel (both in name and pipe id).
To fix this, we prepend the device name of the parent device that the
MHI channels belong to. Since different instances of the same product
should have unique device names, this makes the MHI channel devices for
each product also unique.
Additionally, remove the pipe id from the MHI channel device name. This
is an internal detail to the MHI product that provides little value, and
imposes too much device specific internal details to userspace. It is
expected that channel with a specific name (ie "SAHARA") has a specific
client, and it does not matter what pipe id that channel is enumerated on.
The pipe id is an internal detail between the MHI bus, and the hardware.
The client is not expected to make decisions based on the pipe id, and to
do so would require the client to have intimate knowledge of the hardware,
which is inappropiate as it may violate the layering provided by the MHI
bus. The limitation of doing this is that each product may only have one
instance of a channel by a unique name. This limitation is appropriate
given the usecases of MHI channels.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading or writing MHI registers, the core assumes that the physical
link is a memory mapped PCI link. This assumption may not hold for all
MHI devices. The controller knows what is the physical link (ie PCI, I2C,
SPI, etc), and therefore knows the proper methods to access that link.
The controller can also handle link specific error scenarios, such as
reading -1 when the PCI link went down.
Therefore, it is appropriate that the MHI core requests the controller to
make register accesses on behalf of the core, which abstracts the core
from link specifics, and end up removing an unnecessary assumption.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the MHI core detects invalid data due to a PCI read, it calls into
the controller via link_status() to double check that the link is infact
down. All in all, this is pretty pointless, and racy. There are no good
reasons for this, and only drawbacks.
Its pointless because chances are, the controller is going to do the same
thing to determine if the link is down - attempt a PCI access and compare
the result. This does not make the link status decision any smarter.
Its racy because its possible that the link was down at the time of the
MHI core access, but then recovered before the controller access. In this
case, the controller will indicate the link is not down, and the MHI core
will precede to use a bad value as the MHI core does not attempt to retry
the access.
Retrying the access in the MHI core is a bad idea because again, it is
racy - what if the link is down again? Furthermore, there may be some
higher level state associated with the link status, that is now invalid
because the link went down.
The only reason why the MHI core could see "invalid" data when doing a PCI
access, that is actually valid, is if the register actually contained the
PCI spec defined sentinel for an invalid access. In this case, it is
arguable that the MHI implementation broken, and should be fixed, not
worked around.
Therefore, remove the link_status() callback before anyone attempts to
implement it.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerdown is necessary if mhi_sync_power_up fails due to a timeout, to
clean up the resources. Otherwise a BUG could be triggered when
attempting to clean up MSIs because the IRQ is still active from a
request_irq().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logic modules on the Integrator/AP (Application Platform)
are logic tiles with (typically) one or a few peripheral
devices. They are most commonly used for FPGA prototyping.
Using the device tree node for logic tiles, we probe them
in order and check if the special system controller register
confirm their presence before populating the node for a tile.
This supercedes the code in arch/arm/mach-integrator/lm.[c|h]
and makes it possible to populate the tiles using the device
tree instead of boardfile-based descriptions.
Tested with all peripherals including graphics and MMC card
working fine with the IM-PD1 example tile from Arm.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mhi_alloc_device() function never returns NULL, it returns error
pointers.
Fixes: da1c4f8569 ("bus: mhi: core: Add support for creating and destroying MHI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200407093133.GM68494@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for MHI suspend and resume states. While at it, the
mhi_notify() function needs to be exported as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200427075829.9304-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are the usual updates for SoC specific device drivers and related
subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU and
TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qbsP
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Pull crypto updates from Herbert Xu:
"API:
- Fix out-of-sync IVs in self-test for IPsec AEAD algorithms
Algorithms:
- Use formally verified implementation of x86/curve25519
Drivers:
- Enhance hwrng support in caam
- Use crypto_engine for skcipher/aead/rsa/hash in caam
- Add Xilinx AES driver
- Add uacce driver
- Register zip engine to uacce in hisilicon
- Add support for OCTEON TX CPT engine in marvell"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
crypto: af_alg - bool type cosmetics
crypto: arm[64]/poly1305 - add artifact to .gitignore files
crypto: caam - limit single JD RNG output to maximum of 16 bytes
crypto: caam - enable prediction resistance in HRWNG
bus: fsl-mc: add api to retrieve mc version
crypto: caam - invalidate entropy register during RNG initialization
crypto: caam - check if RNG job failed
crypto: caam - simplify RNG implementation
crypto: caam - drop global context pointer and init_done
crypto: caam - use struct hwrng's .init for initialization
crypto: caam - allocate RNG instantiation descriptor with GFP_DMA
crypto: ccree - remove duplicated include from cc_aead.c
crypto: chelsio - remove set but not used variable 'adap'
crypto: marvell - enable OcteonTX cpt options for build
crypto: marvell - add the Virtual Function driver for CPT
crypto: marvell - add support for OCTEON TX CPT engine
crypto: marvell - create common Kconfig and Makefile for Marvell
crypto: arm/neon - memzero_explicit aes-cbc key
crypto: bcm - Use scnprintf() for avoiding potential buffer overflow
crypto: atmel-i2c - Fix wakeup fail
...
Add a new api that returns Management Complex firmware version
and make the required structure public. The api's first user will be
the caam driver for setting prediction resistance bits.
Signed-off-by: Andrei Botila <andrei.botila@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For some scenarios like controller suspend and resume, mhi_destroy_device()
will get called without mhi_unregister_controller(). In that case, the
references to the mhi_dev created for the channels will not be dropped
but the channels will be destroyed as per the spec. This will cause issue
during resume as the channels will not be created due to the fact that
mhi_dev is not NULL.
Hence, this change decrements the refcount for mhi_dev in
mhi_destroy_device() for concerned channels and also sets mhi_dev to NULL
in release_device().
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bhie field in mhi_cntrl needs to be initialized to proper register
base in order to make mhi_rddm_prepare() to work. Otherwise,
mhi_rddm_prepare() will cause NULL pointer dereference.
Fixes: 6fdfdd2732 ("bus: mhi: core: Add support for downloading RDDM image during panic")
Reported-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MHI register base has several registers used for getting the MHI
specific information such as version, family, major, and minor numbers
from the device. This information can be used by the controller drivers
for usecases such as applying quirks for a specific revision etc...
While at it, let's also rearrange the local variables
in mhi_register_controller().
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just merge in a ti-sysc fix for am335x lcdc suspend/resume issue, and
resolve merge conflict.
-----BEGIN PGP SIGNATURE-----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=k3V/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
Fix for ti-sysc suspend/resume issue on am335x for v5.7 merge window
Just merge in a ti-sysc fix for am335x lcdc suspend/resume issue, and
resolve merge conflict.
* tag 'omap-for-v5.7/ti-sysc-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix quirk flags for lcdc on am335x
Link: https://lore.kernel.org/r/pull-1584132028-918607@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few more fixes for omaps
Just few dts fixes:
- A fix droid4 touchscreen stopping working with lost gpio interrupts
- Also limit omap5 dma range similar to what we've recently done for dra7
* tag 'omap-for-v5.6/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: dts: N900: fix onenand timings
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
Link: https://lore.kernel.org/r/pull-1584575254-461940@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
-----BEGIN PGP SIGNATURE-----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=yBY0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for v5.6
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
* tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
bus: sunxi-rsb: Return correct data when mixing 16-bit and 8-bit reads
ARM: dts: sun8i-a83t-tbs-a711: Fix USB OTG mode detection
ARM: dts: sun8i-a83t-tbs-a711: HM5065 doesn't like such a high voltage
ARM: dts: sun8i: a83t: Fix incorrect clk and reset macros for EMAC device
Link: https://lore.kernel.org/r/20200313055233.GA19649@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver changes for ti-sysc interconnect target module driver mostly
to be able to probe display subsystem (DSS) without platform data:
- Rename clk_enable/disable quirks to less confusing pre and post
reset quirks
- Enable module reset to work with modules with no sysconfig register
- Also consider non-existing module register when matching quirks
- Don't warn with nested ti-sysc devices
- Implement basic SoC revision handling
- Detect DSS related devices
- Implement DSS reset quirks
Note that there is also a DSS driver specific probe fix to allow
probing devices configured for interconnect target module data that
was agreed to be merged along with the ti-sysc driver changes.
And then there also changes to handle RTC, EDMA and PRUSS:
- Add module unlock quirk for RTC
- Detect EDMA modules
- Add support for handling PRUSS
-----BEGIN PGP SIGNATURE-----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=KmZS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
Driver changes for ti-sysc for v5.7 merge window
Driver changes for ti-sysc interconnect target module driver mostly
to be able to probe display subsystem (DSS) without platform data:
- Rename clk_enable/disable quirks to less confusing pre and post
reset quirks
- Enable module reset to work with modules with no sysconfig register
- Also consider non-existing module register when matching quirks
- Don't warn with nested ti-sysc devices
- Implement basic SoC revision handling
- Detect DSS related devices
- Implement DSS reset quirks
Note that there is also a DSS driver specific probe fix to allow
probing devices configured for interconnect target module data that
was agreed to be merged along with the ti-sysc driver changes.
And then there also changes to handle RTC, EDMA and PRUSS:
- Add module unlock quirk for RTC
- Detect EDMA modules
- Add support for handling PRUSS
* tag 'omap-for-v5.7/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Add support for PRUSS SYSC type
dt-bindings: bus: ti-sysc: Add support for PRUSS SYSC type
bus: ti-sysc: Detect EDMA and set quirk flags for tptc
bus: ti-sysc: Fix wrong offset for display subsystem reset quirk
bus: ti-sysc: Implement display subsystem reset quirk
bus: ti-sysc: Detect display subsystem related devices
bus: ti-sysc: Handle module unlock quirk needed for some RTC
bus: ti-sysc: Implement SoC revision handling
bus: ti-sysc: Don't warn about legacy property for nested ti-sysc devices
bus: ti-sysc: Consider non-existing registers too when matching quirks
bus: ti-sysc: Improve reset to work with modules with no sysconfig
bus: ti-sysc: Rename clk related quirks to pre_reset and post_reset quirks
bus: ti-sysc: Fix 1-wire reset quirk
drm/omap: Prepare DSS for probing without legacy platform data
Link: https://lore.kernel.org/r/pull-1583511417-919838@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix up the device resources for the broken firmware to avoid
use-after-free warnings from KASAN in the host removal path
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hIMK
-----END PGP SIGNATURE-----
Merge tag 'hisi-drivers-for-5.7' of git://github.com/hisilicon/linux-hisi into arm/drivers
ARM64: hisi: SoC driver updates for 5.7
- Fix up the device resources for the broken firmware to avoid
use-after-free warnings from KASAN in the host removal path
* tag 'hisi-drivers-for-5.7' of git://github.com/hisilicon/linux-hisi:
bus: hisi_lpc: Fixup IO ports addresses to avoid use-after-free in host removal
Link: https://lore.kernel.org/r/5E61F700.5060301@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The module owner field can be used to prevent the removal of kernel
modules when there are any device files associated with it opened in
userspace. Hence, modify the API to pass module owner field. For
convenience, module_mhi_driver() macro is used which takes care of
passing the module owner through THIS_MODULE of the module of the
driver and also avoiding the use of specifying the default MHI client
driver register/unregister routines.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix printk format warning by using %z for size_t modifier:
../drivers/bus/mhi/core/boot.c: In function `mhi_rddm_prepare':
../drivers/bus/mhi/core/boot.c:55:15: warning: format `%lx' expects argument of type `long unsigned int', but argument 5 has type `size_t {aka unsigned int}' [-Wformat=]
dev_dbg(dev, "Address: %p and len: 0x%lx sequence: %u
",
Link: http://lkml.kernel.org/r/c4852a82-cdb9-6318-70a4-96ccb4ba5af2@infradead.org
Fixes: 6fdfdd2732 ("bus: mhi: core: Add support for downloading RDDM image during panic")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Hemant Kumar <hemantk@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20200324022505.UiPPJZVXX%akpm@linux-foundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add uevent support to MHI bus so that the client drivers can be autoloaded
by udev when the MHI devices gets created. The client drivers are
expected to provide MODULE_DEVICE_TABLE with the MHI id_table struct so
that the alias can be exported.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for transferring data between external modem and host
processor using MHI protocol.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for processing the MHI data and control
events from the client device. The client device can report various
events such as EE events, state change events by interrupting the
host through IRQ and adding events to the event rings allocated by
the host during initialization.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI protocol supports downloading RDDM (RAM Dump) image from the
device through BHIE. This is useful to debugging as the RDDM image
can capture the firmware state.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI supports downloading the device firmware over BHI/BHIe (Boot Host
Interface) protocol. Hence, this commit adds necessary helpers, which
will be called during device power up stage.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for basic MHI PM operations such as
mhi_async_power_up, mhi_sync_power_up, and mhi_power_down. These
routines places the MHI bus into respective power domain states
and calls the state_transition APIs when necessary. The MHI
controller driver is expected to call these PM routines for
MHI powerup and powerdown.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for transitioning the MHI states as a
part of the power management operations. Helpers functions are
provided for the state transitions, which will be consumed by the
actual power management routines.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: removed dma_zalloc_coherent() and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for ringing channel and event ring doorbells
by MHI host. The MHI host can use the channel and event ring doorbells
for notifying the client device about processing transfer and event
rings which it has queued using MMIO registers.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for creating and destroying MHI devices. The
MHI devices binds to the MHI channels and are used to transfer data
between MHI host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI client drivers with the
MHI stack. MHI client drivers binds to one or more MHI devices inorder
to sends and receive the upper-layer protocol packets like IP packets,
modem control messages, and diagnostics messages over MHI bus.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI controller drivers with
the MHI stack. MHI controller drivers manages the interaction with the
MHI client devices such as the external modems and WiFi chipsets. They
are also the MHI bus master in charge of managing the physical link
between the host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: added static config for controllers and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: removed DT dependency, splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200220095854.4804-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit adb72394e2 ("ARM: OMAP2+: Drop legacy platform data for am3
lcdc") dropped legacy platform data but we never added the quirks for
SWSUP_SIDLE and SWSUP_MSTANDBY for lcdc for ti-sysc driver.
This breaks suspend/resume. Let's fix the issue by enabling the same
quirks for ti-sysc driver as we had earlier with platform data.
Fixes: adb72394e2 ("ARM: OMAP2+: Drop legacy platform data for am3 lcdc")
Fixes: 23731eac98 ("bus: ti-sysc: Detect devices on am335x when DEBUG is enabled")
Reported-by: Keerthy <j-keerthy@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS present on AM33xx/AM43xx/AM57xx has a very unique
SYSCFG register. The register follows the OMAP4-style SYSC_TYPE3
for Master Standby and Slave Idle, but also has two additional
unique fields - STANDBY_INIT and SUB_MWAIT. The STANDBY_INIT is
a control bit that is used to initiate a Standby sequence (when
set) and trigger a MStandby request to the SoC's PRCM module. This
same bit is also used to enable the OCP master ports (when cleared)
to allow the PRU cores to access any peripherals or memory beyond
the PRU subsystem. The SUB_MWAIT is a ready status field for the
external access.
Add support for this SYSC type. The STANDBY_INIT has to be set
during suspend, without which it results in a hang in the resume
sequence on AM33xx/AM43xx boards and requires a board reset to
come out of the hang. Any PRU applications requiring external
access are supposed to clear the STANDBY_INIT bit. Note that
the PRUSS context is lost during a suspend sequence because the
PRUSS module is reset and/or disabled.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated quirk define number and to use -ENODEV]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to probe EDMA with ti-sysc interconnect target module and with
device tree data, we need to properly detect EDMA and set the flags for
SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY for tptc.
We have these flags currently set for am4 and dra7, but not for am335x.
Let's set them for all the SoCs as the tptc module should behave the
same for all of them. It's likely that am335x was never tested to idle
EDMA tptc.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset
quirk") added support for DSS reset, but is using dispc offset also for
DSS also registers as reported by Tomi Valkeinen <tomi.valkeinen@ti.com>.
Also, we're not using dispc_offset for dispc IRQSTATUS register so let's
fix that too.
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series of changes contains few code fixes for issues
recently discovered:
- A build fix for ARMv6 only configs when CONFIG_HAVE_ARM_SMCCC is
not set
- A fix for ti-sysc quirk handling for 1-wire hdq reset
And a handful of dts fixes that I had queued up and should
have already sent earlier instead of waiting for the code
fixes to get sorted out:
- Fix naming of vsys_3v3 regulator for dra7-evm
- Fix incorrect OPP node names for am437x-idk-evm
- Fix IPU1 mux clock parent source for dra7
- Add missing PWM property for dra7 timers 13 to 16
- Add missing dma-ranges for dra7 PCIe nodes
- Fix mmc3 max-frequency for dra76x
-----BEGIN PGP SIGNATURE-----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=UHKz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few fixes for omaps for v5.6-rc cycle
This series of changes contains few code fixes for issues
recently discovered:
- A build fix for ARMv6 only configs when CONFIG_HAVE_ARM_SMCCC is
not set
- A fix for ti-sysc quirk handling for 1-wire hdq reset
And a handful of dts fixes that I had queued up and should
have already sent earlier instead of waiting for the code
fixes to get sorted out:
- Fix naming of vsys_3v3 regulator for dra7-evm
- Fix incorrect OPP node names for am437x-idk-evm
- Fix IPU1 mux clock parent source for dra7
- Add missing PWM property for dra7 timers 13 to 16
- Add missing dma-ranges for dra7 PCIe nodes
- Fix mmc3 max-frequency for dra76x
* tag 'omap-for-v5.6/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: dra7-l4: mark timer13-16 as pwm capable
ARM: dts: dra7xx-clocks: Fixup IPU1 mux clock parent source
ARM: dts: am437x-idk-evm: Fix incorrect OPP node names
ARM: dts: dra7-evm: Rename evm_3v3 regulator to vsys_3v3
Link: https://lore.kernel.org/r/pull-1582903541-589933@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Some released ACPI FW for Huawei boards describes incorrect the port IO
address range for child devices, in that it tells us the IO port max range
is 0x3fff for each child device, which is not correct. The address range
should be [e4:e8) or similar. With this incorrect upper range, the child
device IO port resources overlap.
As such, the kernel thinks that the LPC host serial device is a child of
the IPMI device:
root@(none)$ more /proc/ioports
[...]
00ffc0e3-00ffffff : hisi-lpc-ipmi.0.auto
00ffc0e3-00ffc0e3 : ipmi_si
00ffc0e4-00ffc0e4 : ipmi_si
00ffc0e5-00ffc0e5 : ipmi_si
00ffc2f7-00ffffff : serial8250.1.auto
00ffc2f7-00ffc2fe : serial
root@(none)$
They should both be siblings. Note that these are logical PIO addresses,
which have a direct mapping from the FW IO port ranges.
This shows up as a real issue when we enable CONFIG_KASAN and
CONFIG_DEBUG_TEST_DRIVER_REMOVE - we see use-after-free warnings in the
host removal path:
==================================================================
BUG: KASAN: use-after-free in release_resource+0x38/0xc8
Read of size 8 at addr ffff0026accdbc38 by task swapper/0/1
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.5.0-rc6-00001-g68e186e77b5c-dirty #1593
Hardware name: Huawei Taishan 2180 /D03, BIOS Hisilicon D03 IT20 Nemo 2.0 RC0 03/30/2018
Call trace:
dump_backtrace+0x0/0x290
show_stack+0x14/0x20
dump_stack+0xf0/0x14c
print_address_description.isra.9+0x6c/0x3b8
__kasan_report+0x12c/0x23c
kasan_report+0xc/0x18
__asan_load8+0x94/0xb8
release_resource+0x38/0xc8
platform_device_del.part.10+0x80/0xe0
platform_device_unregister+0x20/0x38
hisi_lpc_acpi_remove_subdev+0x10/0x20
device_for_each_child+0xc8/0x128
hisi_lpc_acpi_remove+0x4c/0xa8
hisi_lpc_remove+0xbc/0xc0
platform_drv_remove+0x3c/0x68
really_probe+0x174/0x548
driver_probe_device+0x7c/0x148
device_driver_attach+0x94/0xa0
__driver_attach+0xa4/0x110
bus_for_each_dev+0xe8/0x158
driver_attach+0x30/0x40
bus_add_driver+0x234/0x2f0
driver_register+0xbc/0x1d0
__platform_driver_register+0x7c/0x88
hisi_lpc_driver_init+0x18/0x20
do_one_initcall+0xb4/0x258
kernel_init_freeable+0x248/0x2c0
kernel_init+0x10/0x118
ret_from_fork+0x10/0x1c
...
The issue here is that the kernel created an incorrect parent-child
resource dependency between two devices, and references the false parent
node when deleting the second child device, when it had been deleted
already.
Fix up the child device resources from FW to create proper IO port
resource relationships for broken FW.
With this, the IO port layout looks more healthy:
root@(none)$ more /proc/ioports
[...]
00ffc0e3-00ffc0e7 : hisi-lpc-ipmi.0.auto
00ffc0e3-00ffc0e3 : ipmi_si
00ffc0e4-00ffc0e4 : ipmi_si
00ffc0e5-00ffc0e5 : ipmi_si
00ffc2f7-00ffc2ff : serial8250.1.auto
00ffc2f7-00ffc2fe : serial
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The display subsystem (DSS) needs the child outputs disabled for reset.
In order to prepare to probe DSS without legacy platform data, let's
implement sysc_pre_reset_quirk_dss() similar to what we have for the
platform data with omap_dss_reset().
Note that we cannot directly use the old omap_dss_reset() without
platform data callbacks and updating omap_dss_reset() to understand
struct device. And we will be dropping omap_dss_reset() anyways when
all the SoCs are probing with device tree, so let's not mess with the
legacy code at all.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Because of the i2c quirk we have the reset quirks named in a confusing
way. Let's fix the 1-wire quirk accordinlyg. Then let's switch to using
better naming later on.
Fixes: 4e23be473e ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to prepare probing display subsystem (DSS) with ti-sysc
interconnect target module driver and device tree data, let's
detect DSS related modules.
We need to also add reset quirk handling for DSS, but until that's
done, let's just enable the optional clock quirks for DSS and
omap4 HDMI. The rest is just naming of modules if CONFIG_DEBUG
is set.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RTC modules on am3 and am4 need quirk handling to unlock and lock
them for reset so let's add the quirk handling based on what we already
have for legacy platform data. In later patches we will simply drop the
RTC related platform data and the old quirk handling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to know SoC type and features for cases where the same SoC
may be installed in various versions on the same board and would need
a separate dts file otherwise for the different variants.
For example, am3703 is pin compatible with omap3630, but has sgx and
iva accelerators disabled. We must not try to access the sgx or iva
module registers on am3703, and need to set the unavailable devices
disabled early.
Let's also detect omap3430 as that is needed for display subsystem
(DSS) reset later on, and GP vs EMU or HS devices. Further SoC
specific disabled device detection can be added as needed, such as
dra71x vs dra76x rtc and usb4.
Cc: Adam Ford <aford173@gmail.com>
Cc: André Hentschel <nerv@dawncrow.de>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases we can have nested ti-sysc instances that may still use the
legacy "ti,hwmods" property. Let's not warn if that's the case.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently setting -1 for non-existing sysconfig related registers
for quirks, but setting -ENODEV elsewhere. And for matching the quirks,
we're now just ignoring the non-existing registers. This will cause issues
with misdetecting DSS registers as the hardware revision numbers can have
duplicates.
To avoid this, let's standardize on using -ENODEV also for the quirks
instead of -1. That way we can always just test for a match without adding
any more complicated logic.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least display susbsystem (DSS) has modules with no sysconfig registers
and rely on custom function for module reset handling. Let's make reset
work with that too.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clk_disable_quirk and clk_enable_quirk should really be called
pre_reset_quirk and post_reset_quirk to avoid confusion like we had
with hdq1w reset.
Let's also rename the related functions so the code is easier to follow.
Note that we also have reset_done_quirk that is needed in some cases
after checking the separate register for reset done bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
When doing a 16-bit read that returns data in the MSB byte, the
RSB_DATA register will keep the MSB byte unchanged when doing
the following 8-bit read. sunxi_rsb_read() will then return
a result that contains high byte from 16-bit read mixed with
the 8-bit result.
The consequence is that after this happens the PMIC's regmap will
look like this: (0x33 is the high byte from the 16-bit read)
% cat /sys/kernel/debug/regmap/sunxi-rsb-3a3/registers
00: 33
01: 33
02: 33
03: 33
04: 33
05: 33
06: 33
07: 33
08: 33
09: 33
0a: 33
0b: 33
0c: 33
0d: 33
0e: 33
[snip]
Fix this by masking the result of the read with the correct mask
based on the size of the read. There are no 16-bit users in the
mainline kernel, so this doesn't need to get into the stable tree.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The input_read function declares the size of the hex array relative to
sizeof(buf), but buf is a pointer argument of the function. The hex
array is meant to contain hexadecimal representation of the bin array.
Link: https://lore.kernel.org/r/20200215142130.22743-1-marek.behun@nic.cz
Fixes: 5bc7f990cd ("bus: Add support for Moxtet bus")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reported-by: sohu0106 <sohu0106@126.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Here is the big char/misc/whatever driver changes for 5.6-rc1
Included in here are loads of things from a variety of different driver
subsystems:
- soundwire updates
- binder updates
- nvmem updates
- firmware drivers updates
- extcon driver updates
- various misc driver updates
- fpga driver updates
- interconnect subsystem and driver updates
- bus driver updates
- uio driver updates
- mei driver updates
- w1 driver cleanups
- various other small driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFKeQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynjVACgg6JWfOyPCnz3GfRD1vQZyUl+Hg0An1H+Eh08
+LQk5Qpb3vVwBpCp6qR3
=MB+D
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc/whatever driver changes for 5.6-rc1
Included in here are loads of things from a variety of different
driver subsystems:
- soundwire updates
- binder updates
- nvmem updates
- firmware drivers updates
- extcon driver updates
- various misc driver updates
- fpga driver updates
- interconnect subsystem and driver updates
- bus driver updates
- uio driver updates
- mei driver updates
- w1 driver cleanups
- various other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (86 commits)
mei: me: add jasper point DID
char: hpet: Use flexible-array member
binder: fix log spam for existing debugfs file creation.
mei: me: add comet point (lake) H device ids
nvmem: add QTI SDAM driver
dt-bindings: nvmem: add binding for QTI SPMI SDAM
dt-bindings: imx-ocotp: Add i.MX8MP compatible
dt-bindings: soundwire: fix example
soundwire: cadence: fix kernel-doc parameter descriptions
soundwire: intel: report slave_ids for each link to SOF driver
siox: Use the correct style for SPDX License Identifier
w1: omap-hdq: Simplify driver with PM runtime autosuspend
firmware: stratix10-svc: Remove unneeded semicolon
firmware: google: Probe for a GSMI handler in firmware
firmware: google: Unregister driver_info on failure and exit in gsmi
firmware: google: Release devices before unregistering the bus
slimbus: qcom: add missed clk_disable_unprepare in remove
slimbus: Use the correct style for SPDX License Identifier
slimbus: qcom-ngd-ctrl: Use dma_request_chan() instead dma_request_slave_channel()
dt-bindings: SLIMBus: add slim devices optional properties
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Few changes to implement quirk handling for cases where we need to block
clockdomain autoidle, drop old MMU specific quirks, and simplify the
return code for sysc_init_resets().
-----BEGIN PGP SIGNATURE-----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=2N9h
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
ti-sysc driver changes for omaps for v5.6 merge window
Few changes to implement quirk handling for cases where we need to block
clockdomain autoidle, drop old MMU specific quirks, and simplify the
return code for sysc_init_resets().
* tag 'omap-for-v5.6/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Use PTR_ERR_OR_ZERO() to simplify code
bus: ti-sysc: Drop MMU quirks
bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO
Link: https://lore.kernel.org/r/pull-1579200367-372444@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
- Various cleanup on the following drivers:
- Turris Mox rWTM firmware
- Moxtet bus
- Armada 37xx rWTM mailbox
- Marvell EBU Device Bus
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXhn9YQAKCRALBhiOFHI7
1eaRAJ49SHCftal9aCuOrcl2/w4OBmB3awCffwAbLS0fTC/2ynqOshjavVbzmes=
=JM34
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-5.6-1' of git://git.infradead.org/linux-mvebu into arm/drivers
mvebu drivers for 5.6 (part 1)
- Various cleanup on the following drivers:
- Turris Mox rWTM firmware
- Moxtet bus
- Armada 37xx rWTM mailbox
- Marvell EBU Device Bus
* tag 'mvebu-drivers-5.6-1' of git://git.infradead.org/linux-mvebu:
mailbox: armada-37xx-rwtm: convert to devm_platform_ioremap_resource
memory: mvebu-devbus: convert to devm_platform_ioremap_resource
bus: moxtet: declare moxtet_bus_type as static
firmware: turris-mox-rwtm: small white space cleanup
Link: https://lore.kernel.org/r/877e1x3nxc.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
Contains a single fix to remove a Kconfig dependency that's no longer
required.
-----BEGIN PGP SIGNATURE-----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=eyhT
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.6-bus' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
bus: tegra: Changes for v5.6-rc1
Contains a single fix to remove a Kconfig dependency that's no longer
required.
* tag 'tegra-for-5.6-bus' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
bus: tegra-aconnect: Remove PM_CLK dependency
Link: https://lore.kernel.org/r/20200111003553.2411874-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the proper form of the empty initializer when working with
structures that contain an array. Otherwise, older gcc versions (eg gcc
4.9) will complain about this.
Fixes: 1ac210d128 ("bus: fsl-mc: add the fsl_mc_get_endpoint function")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20191204142950.30206-1-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ACONNECT bus driver does not use pm-clk interface anymore and hence
the dependency can be removed from its Kconfig option.
Fixes: 0d7dab9261 ("bus: tegra-aconnect: use devm_clk_*() helpers")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This symbol is not meant to be used from elsewhere.
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Commit d878970f6c ("bus: ti-sysc: Add separate functions for handling
clocks") separated handling of optional clocks from the main clocks, but
introduced an issue where we do not necessarily allocate a slot for both
fck and ick clocks, but still assume fixed slots for enumerating over the
clocks.
Let's fix the issue by ensuring we always have slots for both fck and ick
even if we don't use ick, and don't attempt to enumerate optional clocks
if not allocated.
In the long run we might want to simplify things a bit by only allocating
space only for the optional clocks as we have only few devices with
optional clocks.
Fixes: d878970f6c ("bus: ti-sysc: Add separate functions for handling clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes coccicheck warning:
drivers/bus/ti-sysc.c:506:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP IOMMU driver no longer uses the pm_runtime_irq_safe() API
after commit 1432ebbd60 ("iommu/omap: remove pm_runtime_irq_safe
flag for OMAP IOMMUs"), so the SYSC_QUIRK_LEGACY_IDLE quirk is no
longer needed for MMU devices. Drop the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For dra7 dcan and dwc3 instances we need to block clockdomain autoidle.
Let's do this with CLKDM_NOAUTO quirk flag and enable it for dcan and
dwc3.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have dts property for "ti,sysc-delay-us", and we're using it, but the
wait after OCP softreset only happens if devices are probed in legacy mode.
Let's add a delay after writing the OCP softreset when specified.
Fixes: e0db94fe87 ("bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for
musb") added quirk handling for mstandby quirk but did not consider that
we also need a quirk variant for SYSC_QUIRK_FORCE_MSTANDBY.
We need to use forced idle mode for both SYSC_QUIRK_SWSUP_MSTANDBY and
SYSC_QUIRK_FORCE_MSTANDBY, but SYSC_QUIRK_SWSUP_MSTANDBY also need to
additionally also configure no-idle mode when enabled.
Fixes: 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for musb")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just few minor changes that can be merged when suitable, but would
be good to have these in v5.5-rc1 to remove dependencies between branches
for more changes later on in v5.6:
- Add quirk handling for AESS (Audio Engine Sub System)
- We want to drop the useless gptimer option for omap4 as there are local
timers
- A minor error path handling improvment for sysc_child_add_named_clock()
that will make further patching a bit easier
-----BEGIN PGP SIGNATURE-----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=Yb3M
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/ti-sysc-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few ti-sysc related fixes for v5.5 merge window
Just few minor changes that can be merged when suitable, but would
be good to have these in v5.5-rc1 to remove dependencies between branches
for more changes later on in v5.6:
- Add quirk handling for AESS (Audio Engine Sub System)
- We want to drop the useless gptimer option for omap4 as there are local
timers
- A minor error path handling improvment for sysc_child_add_named_clock()
that will make further patching a bit easier
* tag 'omap-for-v5.5/ti-sysc-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Adjust exception handling in sysc_child_add_named_clock()
ARM: OMAP2+: Drop useless gptimer option for omap4
bus: ti-sysc: Add module enable quirk for audio AESS
Link: https://lore.kernel.org/r/pull-1574273726-31367@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl3pORkPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3FK0P/0EG4lK+il7nE3pd9yIGUjlcYuumIjoxvyC9
9ef202POJLIO3yMlsNyGFR+aOknFO/GtGvDkDFhTtlsGCL40tVzVsyo7ZQo+8mXD
abr+H74NmRXImc+SISYR8X1CD6vEi3oi/no1y5dRzknlBikfsdSLKXJSMYBJ2A6t
DNLwu0h1IZhPk7XQQsxaElG/a9HN8eueMdP20J1IlhOh0GiOwm+rbsLSZNbA/W9m
53XhFs3Ag39SDE0BfXsS+XOWTE7FheZsZk2XQrOwYm9PnxjpIWH7FE2sYsk6uUIc
Pa1b6wB5zlRnxvVHP0m3GXhbTUJDYDK3oybHffI4Mzd0cyZQHC92LhUXFrlTxkaf
6kyhJOTdd5KMlZ2LS7jkwLqb30ieXBPKAREjdbRt6hpvu5P6G+bZQphTEeNAZC61
XnX8mQ/XeoHdoGY5MvS8ht6a1qDF29ebA0/02seicThGK6tS9Qsju6Zo0sg9H1NH
weK6jDuzLq5jpv/LB1apigrDSx+zddRzrwkwy85hR5aWOQhG0xjOoFBProbTS0to
wR46zCEkbGZv4uc0gRuIdp0NR/lguqgDWPeoLluoTqmcpKS6N3RyxD0bWzlvgDFA
fpYxVNKavHneWjfZ7U5RbYXD6jycJcuLaCOs16nrtUbMgJ9pqclLIaZXn7ZTRIuT
RW6NgfZV
=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Here is the big staging and iio set of patches for the 5.5-rc1 release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6lVQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFnwCgyvZ62uUyQTRey0zvNTe3I4fY9L4AnAnrz3ZC
U6ZA2+Uj3O6qhAr5frRu
=uv8S
-----END PGP SIGNATURE-----
Merge tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / iio updates from Greg KH:
"Here is the big staging and iio set of patches for the 5.5-rc1
release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues"
* tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (548 commits)
staging: vchiq: Have vchiq_dump_* functions return an error code
staging: vchiq: Refactor indentation in vchiq_dump_* functions
staging: fwserial: Fix Kconfig indentation (seven spaces)
staging: vchiq_dump: Replace min with min_t
staging: vchiq: Fix block comment format in vchiq_dump()
staging: octeon: indent with tabs instead of spaces
staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
staging: most: core: remove sysfs attr remove_link
staging: vc04: Fix Kconfig indentation
staging: pi433: Fix Kconfig indentation
staging: nvec: Fix Kconfig indentation
staging: most: Fix Kconfig indentation
staging: fwserial: Fix Kconfig indentation
staging: fbtft: Fix Kconfig indentation
fbtft: Drop OF dependency
fbtft: Make use of device property API
fbtft: Drop useless #ifdef CONFIG_OF and dead code
fbtft: Describe function parameters in kernel-doc
fbtft: Make sure string is NULL terminated
staging: rtl8723bs: remove set but not used variable 'change', 'pos'
...
Add a jump target so that a call of the function “clk_put”
can be better reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must set the autogating bit on enable for AESS (Audio Engine SubSystem)
when probed with ti-sysc interconnect target module driver. Otherwise it
won't idle properly.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- check the LOGIC_PIO_INDIRECT region ops at registration instead of
in the IO port accessors to optimise the lib/ligic_pio.c
- add the hisi LPC driver to the build test for the other architectures
except ALPHA, C6X, HEXAGON and PARISC as they do not define {read,write}sb
by updating the hisi LPC Kconfig and adding a dummy PIO_INDIRECT_SIZE
- clean the sparse complains of the hisi LPC driver
- build logic_pio into a lib to avoid including in the vmlinux when not
referenced
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9R8Z
-----END PGP SIGNATURE-----
Merge tag 'hisi-drivers-for-5.5' of git://github.com/hisilicon/linux-hisi into arm/drivers
ARM64: hisi: SoC driver updates for 5.5
- check the LOGIC_PIO_INDIRECT region ops at registration instead of
in the IO port accessors to optimise the lib/ligic_pio.c
- add the hisi LPC driver to the build test for the other architectures
except ALPHA, C6X, HEXAGON and PARISC as they do not define {read,write}sb
by updating the hisi LPC Kconfig and adding a dummy PIO_INDIRECT_SIZE
- clean the sparse complains of the hisi LPC driver
- build logic_pio into a lib to avoid including in the vmlinux when not
referenced
* tag 'hisi-drivers-for-5.5' of git://github.com/hisilicon/linux-hisi:
logic_pio: Build into a library
bus: hisi_lpc: Expand build test coverage
bus: hisi_lpc: Clean some types
logic_pio: Define PIO_INDIRECT_SIZE for !CONFIG_INDIRECT_PIO
lib: logic_pio: Enforce LOGIC_PIO_INDIRECT region ops are set at registration
Link: https://lore.kernel.org/r/5DC959B9.80301@hisilicon.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently the driver will only ever be built for ARM64 because it selects
CONFIG_INDIRECT_PIO, which itself depends on ARM64.
Expand build test coverage for the driver to other architectures by only
selecting CONFIG_INDIRECT_PIO for ARM64, when we really want it.
We don't include ALPHA, C6X, HEXAGON, and PARISC architectures as they
don't define {read, write}sb.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
