Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip flood broadcast and unknown multicast frames.
On receive set skb->offload_fwd_mark to prevent the SW from flooding to the
same ports.
One exception: Because the ALR is set up to forward STP BPDUs only to CPU,
the SW bridge should flood STP BPDUs if local STP is not enabled.
This is archived by not setting skb->offload_fwd_mark on STP BPDUs.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.
Add an ALR entry with STP state override to fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_xmit_use_arl() introduced in previous patch set is wrong.
The chip flood broadcast and unknown multicast frames. The effect is that
broadcasts and multicasts are duplicated on egress. It is not possible to
configure the chip to direct unknown multicasts to CPU port only.
This means that only unicast frames can be transmitted using ALR lookup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that slave dsa_port always have their name set, there is no need to
pass it to dsa_slave_create() anymore. Remove this argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the optional "label" property and assign a default one directly at
parse time instead of doing it when creating the slave.
For legacy, simply assign the port name stored in cd->port_names.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetching the master device can be done directly when a port is parsed
from device tree or pdata, instead of waiting until dsa_dst_parse.
Now that -EPROBE_DEFER is returned before we add the switch to the tree,
there is no need to check for this error after dsa_dst_parse.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign a port's type at parsed time instead of waiting for the tree to
be completed.
Because this is now done earlier, we can use the port's type in
dsa_port_is_* helpers instead of digging again in topology description.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add symmetrical DSA port parsing functions for pdata and device tree,
used to parse and validate a given port node or platform data.
They don't do much for the moment but will be extended later on to
assign a port type and get device references.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point into hiding the -EINVAL error code in ERR_PTR from a
dsa_get_ports function, simply get the "ports" node directly from within
the dsa_parse_ports_dn function.
This also has the effect to make the pdata and device tree handling code
symmetrical inside _dsa_register_switch.
At the same time, rename dsa_parse_ports_dn to dsa_parse_ports_of
because _of is a more common suffix for device tree parsing functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
The new bindings (dsa2.c) and the old bindings (legacy.c) share two
helpers dsa_cpu_dsa_setup and dsa_cpu_dsa_destroy, used to register or
deregister a fixed PHY if a given port has a corresponding device node.
Unclutter the code by moving them into two new port.c helpers,
dsa_port_fixed_link_register_of and dsa_port_fixed_link_(un)register_of.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA core provides port types, there is no need to keep this
information at the switch level. This is a static information that is
part of a DSA core dsa_port structure. Remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an enumerated type for ports, which will be way more explicit
to identify a port type instead of digging into switch port masks.
A port can be of type CPU, DSA, user, or unused by default. This is a
static parsed information that cannot be changed at runtime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPU transmit directly to port using tag, the LAN9303 does not
learn MAC addresses received on the CPU port into the ALR.
ALR learning is performed only when transmitting using ALR lookup.
Solution:
If the two external ports are bridged and the packet is not STP BPDU,
then use ALR lookup to allow ALR learning on CPU port.
Otherwise transmit directly to port with STP state override.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code that tried to identify if a PHY designated by Device
Tree required diversion through the DSA-created MDIO bus. This was
created mainly for the bcm_sf2.c driver back when it did not have its
own MDIO bus driver, which it now has since 461cd1b03e ("net: dsa:
bcm_sf2: Register our slave MDIO bus").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Martin Hundebøll <mnhu@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unapply functions are called on the error path.
As for dsa_port_mask, enabled_port_mask and cpu_port_mask won't be used
after so there's no need to unmask the corresponding port bit from them.
This makes dsa_cpu_port_unapply() and dsa_dsa_port_unapply() identical,
which can be factorized later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy code does not unmask the cpu_port_mask and dsa_port_mask as
stated. But this is done on the error path and those masks won't be used
after that. So instead of fixing the bit operation, simply remove it.
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of pdata, the dsa_cpu_parse function calls dev_put() before
making sure it isn't NULL. Fix this.
Fixes: 71e0bbde0d ("net: dsa: Add support for platform data")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are converted to use block callbacks for TC_SETUP_CLS*.
So it is now safe to remove the calls to ndo_setup_tc from cls_*
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced block callback infrastructure and
convert ndo_setup_tc calls for matchall offloads to block callbacks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_master_get_slave is slightly confusing since the idiomatic "get"
term often suggests reference counting, in symmetry to "put".
Rename it to dsa_master_find_slave to make the look up operation clear.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many part of the DSA slave code require to get the master device
assigned to a slave device. Remove dsa_master_netdev() in favor of a
dsa_slave_to_master() helper which does that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many portions of DSA core code require to get the dsa_port structure
corresponding to a slave net_device. For this purpose, introduce a
dsa_slave_to_port() helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both DSA slave create and destroy functions call call_dsa_notifiers with
respectively DSA_PORT_REGISTER and DSA_PORT_UNREGISTER and the same
dsa_notifier_register_info structure.
Wrap this in a dsa_slave_notify helper so prevent cluttering these
functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dsa_slave_create is called, the related port already has a CPU port
assigned to it, available in its cpu_dp member. Use it instead of the
unique tree cpu_dp.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no user for the .set_addr function, remove it from
DSA. If a switch supports this feature (like mv88e6xxx), the
implementation can be done in the driver setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.
This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_ptr is a dsa_port instance, there is no need to keep
the tag operations in the dsa_switch_tree structure. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With DSA, a master net device (CPU facing interface) has a dsa_ptr
pointer to which hangs a dsa_switch_tree. This is not correct because a
master interface is wired to a dedicated switch port, and because we can
theoretically have several master interfaces pointing to several CPU
ports of the same switch fabric.
Change the master interface's dsa_ptr for the CPU dsa_port pointer.
This is a step towards supporting multiple CPU ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to make DSA master devices point to their corresponding
CPU port instead of the whole tree, add copies of dst and rcv in the
dsa_port structure so that we keep fast access in the receive hot path.
Also keep the copies at the beginning of the dsa_port structure in order
to ensure they are available in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging protocol operations are specific to each CPU port,
thus the dsa_device_ops pointer belongs to the dsa_port structure.
>From now on assign a slave's xmit copy from its CPU port tagging
operations. This will ease the future support for multiple CPU ports.
Also keep the tag_ops at the beginning of the dsa_port structure so that
we ensure copies for hot path are in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving the DSA tagging protocol used by a CPU switch, use a
temporary "tag_ops" variable to store the dsa_device_ops instead of
using directly dst->tag_ops. This will make the future patches moving
this pointer around easier to read.
There is no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that the master device is linked to a CPU port by using
"cpu_dp" for the dsa_port variable in master.c instead of "port", then
use a "port" variable to describe the port index, as usually seen in
other places of DSA core.
This will make the future patch touching dsa_ptr more readable. There is
no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging code does not need to know about the DSA architecture,
it only needs to return the slave device corresponding to the source
port index (and eventually the source device index for cascade-capable
switches) parsed from the frame received on the master device.
For this purpose, provide an inline dsa_master_get_slave helper which
validates the device and port indexes and look up the slave device.
This makes the tagging rcv functions more concise and robust, and also
makes dsa_get_cpu_port obsolete.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot be registering the network device first, then setting its
carrier off and finally connecting it to a PHY, doing that leaves a
window during which the carrier is at best inconsistent, and at worse
the device is not usable without a down/up sequence since the network
device is visible to user space with possibly no PHY device attached.
Re-order steps so that they make logical sense. This fixes some devices
where the port was not usable after e.g: an unbind then bind of the
driver.
Fixes: 0071f56e46 ("dsa: Register netdev before phy")
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_nway_reset now that dsa_slave_nway_reset does exactly
the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_set_link_ksettings now that dsa_slave_set_link_ksettings
does exactly the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_get_link_ksettings now that dsa_slave_get_link_ksettings
does exactly the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to store a phy_device in dsa_slave_priv since
net_device already provides one. Simply s/p->phy/dev->phydev/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of returning -EOPNOTSUPP when a slave device has no PHY,
directly return -ENODEV as ethtool and phylib do.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide dsa_port_enable and dsa_port_disable helpers to respectively
enable and disable a switch port. This makes the dsa_port_set_state_now
helper static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA slave open function configures the unicast MAC addresses on the
master device, enable the switch port, change its STP state, then start
the PHY device.
Make the close function symmetric, by first stopping the PHY device,
then changing the STP state, disabling the switch port and restore the
master device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a DSA port's FDB entries is not specific to a DSA slave, so add
a dsa_port_fdb_dump function, similarly to dsa_port_fdb_add and
dsa_port_fdb_del.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few DSA slave functions take a dsa_slave_priv pointer as first
argument, whereas the scope of the slave.c functions is the slave
net_device structure. Fix this and rename dsa_netpoll_send_skb to
dsa_slave_netpoll_send_skb.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of open coding the check.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA overrides the master device ethtool ops, so that it can inject stats
from its dedicated switch CPU port as well.
The related code is currently split in dsa.c and slave.c, but it only
scopes the master net device. Move it to a new master.c DSA core file.
This file will be later extented with master net device specific code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA overrides the master's ethtool ops so that we can inject its CPU
port's statistics. Because of that, we need to setup the ethtool ops
after the master's dsa_ptr pointer has been assigned, not before.
This patch setups the ethtool ops after dsa_ptr is assigned, and
restores them before it gets cleared.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch tree is meant to be applied, it already has a CPU
port. Thus remove the condition of dst->cpu_dp.
Moreover, the next lines access dst->cpu_dp unconditionally.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to store a copy of the master ethtool ops, storing the
original pointer in DSA and the new one in the master netdev itself is
enough.
In the meantime, set orig_ethtool_ops to NULL when restoring the master
ethtool ops and check the presence of the master original ethtool ops as
well as its needed functions before calling them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We originally used skb->priority but that was not quite correct as this
bitfield needs to contain the egress switch queue we intend to send this
SKB to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let switch drivers indicate how many TX queues they support. Some
switches, such as Broadcom Starfighter 2 are designed with 8 egress
queues. Future changes will allow us to leverage the queue mapping and
direct the transmission towards a particular queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two kfree_skb() should be consume_skb(), to be friend with drop monitor
(perf record ... -e skb:kfree_skb)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first call of skb_put_padto() will free up the SKB on error, but we
return NULL which tells dsa_slave_xmit() that the original SKB should be
freed so this would lead to a double free here.
The second skb_put_padto() already frees the passed sk_buff reference
upon error, so calling kfree_skb() on it again is not necessary.
Detected by CoverityScan, CID#1416687 ("USE_AFTER_FREE")
Fixes: e71cb9e009 ("net: dsa: ksz: fix skb freeing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile tested only, but saw no warnings/errors with
allmodconfig build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer frees the original skb when an xmit function returns NULL,
meaning an error occurred. But if the tagging code copied the original
skb, it is responsible of freeing the copy if an error occurs.
The ksz tagging code currently has two issues: if skb_put_padto fails,
the skb copy is not freed, and the original skb will be freed twice.
To fix that, move skb_put_padto inside both branches of the skb_tailroom
condition, before freeing the original skb, and free the copy on error.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking handle, which does not have the inner class
information and drivers wrongly assume clsact->egress as ingress, use
the newly introduced classid identification helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530 inserts the 4 magic header in between the 802.3 address and
protocol field. The patch implements the callback that can be called by
the flow dissector to figure out the real protocol and offset of the
network header. With this patch applied we can properly parse the packet
and thus make hashing function properly.
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to access this struct from within the flow_dissector to fix
dissection for packets coming in on DSA devices.
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save 2628 bytes on arm eabi by allocate only the required 3 ports.
Now that ds->num_ports is correct: In net/dsa/tag_lan9303.c
eliminate duplicate LAN9303_MAX_PORTS, use ds->num_ports.
(Matching the pattern of other net/dsa/tag_xxx.c files.)
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the MDB HW database is synced with the bridge's one, thus,
There is no need to support special dump functionality.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge port attributes/vlan for DSA devices should be set only
from bridge code. Furthermore, The vlans are synced totally with the
bridge so there is no need for special dump support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA drivers do not support bridge flags offload. Yet, this attribute
should be added in order for the bridge to fail when one tries set a
flag on the port, as explained in commit dc0ecabd62 ("net: switchdev:
Add support for querying supported bridge flags by hardware").
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA uses switchdev's implementation of FDB add/del ndos. This
patch moves the implementation inside DSA in order to support the legacy
way for static FDB configuration.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue. In case of a successful
FDB add a notification is sent back to bridge.
In case of hw FDB del failure the static FDB will be deleted from
the bridge, thus, the interface is moved to down state in order to
indicate inconsistent situation.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the switchdev objects are embedded inside the DSA notifier
info. This patch removes this dependency. This is done as a preparation
stage before adding support for learning FDB through the switchdev
notification chain.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_create currently takes 4 arguments while it only needs the
related dsa_port and its name. Remove all other arguments.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_cpu_dsa_setup currently takes 4 arguments but they are all available
from the dsa_port argument. Remove all others.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_switch_alloc() already assigns ds-dev, which can be used in
dsa_switch_setup_one and dsa_cpu_dsa_setups instead of requiring an
additional struct device argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let dsa_slave_setup_tc be a splitter for specific setup_tc types and
push out cls_matchall specific code into a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be aligned with the rest of the types, rename
TC_SETUP_MATCHALL to TC_SETUP_CLSMATCHALL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing with a background iperf pushing 1Gbit/sec worth of
traffic and having both ifconfig and ethtool collect statistics, we
could see quite frequent deadlocks. Convert the often accessed DSA slave
network devices statistics to per-cpu 64-bit statistics to remove these
deadlocks and provide fast efficient statistics updates.
Fixes: f613ed665b ("net: dsa: Add support for 64-bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA slave network devices maintain a pair of bytes and packets counters
for each directions, but these are not 64-bit capable. Re-use
pcpu_sw_netstats which contains exactly what we need for that purpose
and update the code path to report 64-bit capable statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the PHY EEE settings, rename the .set_eee and
.get_eee ops to respectively .set_mac_eee and .get_mac_eee.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch operations for EEE are only meant to configure a port's
MAC EEE settings. The port's PHY EEE settings are accessed by the DSA
layer and must be made available via a proper PHY driver.
In order to reduce this confusion, remove the phy_device argument from
the .set_eee operation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA drivers are calling phy_init_eee if eee_enabled is true.
Move up this statement in the DSA layer to simplify the DSA drivers.
qca8k does not require to cache the ethtool_eee structures from now on.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port's PHY and MAC are both implied in EEE. The current code does
not call the PHY operations if the related device is NULL. Change that
by returning -ENODEV if there's no PHY device attached to the interface.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7530 driver has its dsa_switch_ops::get_tag_protocol function
check ds->cpu_port_mask to issue a warning in case the configured CPU
port is not capable of supporting tags.
After commit 14be36c2c9 ("net: dsa: Initialize all CPU and enabled
ports masks in dsa_ds_parse()") we slightly re-arranged the
initialization such that this was no longer working. Just make sure that
ds->cpu_port_mask is set prior to the first call to get_tag_protocol,
thus restoring the expected contract. In case of error, the CPU port bit
is cleared.
Fixes: 14be36c2c9 ("net: dsa: Initialize all CPU and enabled ports masks in dsa_ds_parse()")
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_is_port_initialized helper is only used by dsa_switch_resume and
dsa_switch_suspend, if CONFIG_PM_SLEEP is enabled. Make it static to
dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 6d3c8c0dd8 ("net: dsa: Remove master_netdev and
use dst->cpu_dp->netdev") and a29342e739 ("net: dsa: Associate
slave network device with CPU port") we would be seeing NULL pointer
dereferences when accessing dst->cpu_dp->netdev too early. In the legacy
code, we actually know early in advance the master network device, so
pass it down to the relevant functions.
Fixes: 6d3c8c0dd8 ("net: dsa: Remove master_netdev and use dst->cpu_dp->netdev")
Fixes: a29342e739 ("net: dsa: Associate slave network device with CPU port")
Reported-by: Jason Cobham <jcobham@questertangent.com>
Tested-by: Jason Cobham <jcobham@questertangent.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to how cross-chip VLAN works, define a bitmap of multicast
group members for a switch, now including its DSA ports, so that
multicast traffic can be sent to all switches of the fabric.
A switch may drop the frames if no user port is a member.
This brings support for multicast in a multi-chip environment.
As of now, all switches of the fabric must support the multicast
operations in order to program a single fabric port.
Reported-by: Jason Cobham <jcobham@questertangent.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Jason Cobham <jcobham@questertangent.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code only assigns the default cpu_dp to all user ports of
the switch to which the CPU port belongs. The user ports of the other
switches of the fabric thus don't have a default CPU port.
This patch fixes this by assigning the cpu_dp of all user ports of all
switches of the fabric when the tree is fully parsed.
Fixes: a29342e739 ("net: dsa: Associate slave network device with CPU port")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper function which will return a reference to the CPU
port used in a dsa_switch_tree. Right now this is a singleton, but this
will change once we introduce multi-CPU port support, so ease the
transition by converting the affected code paths.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports with DSA, have the
dsa_port structure know which CPU it is associated with. This will be
important in order to make sure the correct CPU is used for transmission
of the frames. If not for functional reasons, for performance (e.g: load
balancing) and forwarding decisions.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate master_ethtool_ops and master_orig_ethtool_ops into struct
dsa_port in order to be both consistent, and make things self contained
within the dsa_port structure.
This is a preliminary change to supporting multiple CPU port interfaces.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports, remove
dst->master_netdev and ds->master_netdev and replace them with only one
instance of the common object we have for a port: struct
dsa_port::netdev. ds->master_netdev is currently write only and would be
helpful in the case where we have two switches, both with CPU ports, and
also connected within each other, which the multi-CPU port patch series
would address.
While at it, introduce a helper function used in net/dsa/slave.c to
immediately get a reference on the master network device called
dsa_master_netdev().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a multi-chip switch fabric, it is currently the responsibility of the
driver to add the CPU or DSA (interconnecting chips together) ports as
members of a new VLAN entry. This makes the drivers more complicated.
We want the DSA drivers to be stupid and the DSA core being the one
responsible for caring about the abstracted switch logic and topology.
Make the DSA core program the CPU and DSA ports as part of the VLAN.
This makes all chips of the data path to be aware of VIDs spanning the
the whole fabric and thus, seamlessly add support for cross-chip VLAN.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VLAN object is propagated to every switch chip of the
switch fabric, we can easily ensure that they all support the required
VLAN operations before modifying an entry on a single switch.
To achieve that, remove the condition skipping other target switches,
and add a bitmap of VLAN members, eventually containing the target port,
if we are programming the switch target.
This will allow us to easily add other VLAN members, such as the DSA or
CPU ports (to introduce cross-chip VLAN support) or the other port
members if we want to reduce hardware accesses later.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9520ed8fb8 ("net: dsa: use cpu_switch instead of ds[0]")
replaced the use of dst->ds[0] with dst->cpu_switch since that is
functionally equivalent, however, we can now run into an use after free
scenario after unbinding then rebinding the switch driver.
The use after free happens because we do correctly initialize
dst->cpu_switch the first time we probe in dsa_cpu_parse(), then we
unbind the driver: dsa_dst_unapply() is called, and we rebind again.
dst->cpu_switch now points to a freed "ds" structure, and so when we
finally dereference it in dsa_cpu_port_ethtool_setup(), we oops.
To fix this, simply set dst->cpu_switch to NULL in dsa_dst_unapply()
which guarantees that we always correctly re-assign dst->cpu_switch in
dsa_cpu_parse().
Fixes: 9520ed8fb8 ("net: dsa: use cpu_switch instead of ds[0]")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was no reason for duplicating the code that initializes
ds->enabled_port_mask in both dsa_parse_ports_dn() and
dsa_parse_ports(), instead move this to dsa_ds_parse() which is early
enough before ops->setup() has run.
While at it, we can now make dsa_is_cpu_port() check ds->cpu_port_mask
which is a step towards being multi-CPU port capable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have all the information we need in dsa_port, so use it instead of
repeating the same arguments over and over again.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to have a reference to a dsa_switch, instead we should
pass a reference to a CPU dsa_port, change that. This is a preliminary
change to better support multiple CPU ports.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_switch_suspend() and dsa_switch_resume() are functions that belong in
net/dsa/dsa.c and are not part of the legacy platform support code.
Fixes: a6a71f19fe ("net: dsa: isolate legacy code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of a86d8becc3 ("net: dsa: Factor bottom tag receive functions"),
the rcv caller frees the original SKB in case or error.
Be symmetric with that and make the xmit caller do the same.
At the same time, fix the checkpatch NULL comparison check:
CHECK: Comparison to NULL could be written "!nskb"
#208: FILE: net/dsa/tag_trailer.c:35:
+ if (nskb == NULL)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many rcv functions from net/dsa/tag_*.c have a useless out_drop goto
label which simply returns NULL. Kill it in favor of the obvious.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_ptr is not a void pointer anymore since Nov 2011, as of cf50dcc24f
("dsa: Change dsa_uses_{dsa, trailer}_tags() into inline functions"),
but an explicit dsa_switch_tree pointer, thus remove the (void *) cast.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer uses inline helpers and copy of the tagging functions for
faster access in hot path. Add comments to detail that.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
function ksz_rcv can be made static as it does not need to be
in global scope. Reformat arguments to make it checkpatch warning
free too.
Cleans up sparse warning: "symbol 'ksz_rcv' was not declared. Should
it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for the Microchip KSZ switch family tail tagging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_register_switch function takes a useless struct device
pointer argument, which always equals ds->dev.
Drivers either call it with ds->dev, or with the same device pointer
passed to dsa_switch_alloc, which ends up being assigned to ds->dev.
This patch removes the second argument of the dsa_register_switch and
_dsa_register_switch functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper is only used once and makes the code more complicated that it
should. Remove it and reorganize the variables so that it fits on 80
columns.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the switchdev bridge ageing time attribute is propagated to all
switch chips of the fabric, each switch can check if the requested value
is valid and program itself, so that the whole fabric shares a common
ageing time setting.
This is especially needed for switch chips in between others, containing
no bridge port members but evidently used in the data path.
To achieve that, remove the condition which skips the other switches. We
also don't need to identify the target switch anymore, thus remove the
sw_index member of the dsa_notifier_ageing_time_info notifier structure.
On ZII Dev Rev B (with two 88E6352 and one 88E6185) and ZII Dev Rev C
(with two 88E6390X), we have the following hardware configuration:
# ip link add name br0 type bridge
# ip link set master br0 dev lan6
br0: port 1(lan6) entered blocking state
br0: port 1(lan6) entered disabled state
# echo 2000 > /sys/class/net/br0/bridge/ageing_time
Before this patch:
zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
300000
300000
15000
zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
300000
18750
After this patch:
zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
15000
15000
15000
zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
18750
18750
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new DSA_NOTIFIER_VLAN_ADD and DSA_NOTIFIER_VLAN_DEL events to
notify not only a single switch, but all switches of a the fabric when
an VLAN entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new DSA_NOTIFIER_MDB_ADD and DSA_NOTIFIER_MDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an MDB entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new DSA_NOTIFIER_FDB_ADD and DSA_NOTIFIER_FDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an FDB entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch keeps the port-wide ageing time handling code in
dsa_port_ageing_time, pushes the requested ageing time value in a new
switch fabric notification, and moves the switch-wide ageing time
handling code in dsa_switch_ageing_time.
This has the effect that now not only the switch that the target port
belongs to can be programmed, but all switches composing the switch
fabric. For the moment, keep the current behavior and ignore other
switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA notifier events and info structure definitions are not meant for
DSA drivers and users, but only used internally by the DSA core files.
Move them from the public net/dsa.h file to the private dsa_priv.h file.
Also use this opportunity to turn the events into an anonymous enum,
because we don't care about the values, and this will prevent future
conflicts when adding (and sorting) new events.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which handles VLAN objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which handles MDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which handles FDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which sets a port ageing time in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which sets VLAN filtering on a port in port.c,
where it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DSA port code which bridges a port in port.c, where it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new port.c file to hold all DSA port-wide logic. This patch moves
in the code which sets a port state.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev bridge ageing time attribute setter
from the DSA slave device to the generic DSA port, so that the future
port-wide API can also be used for other port types, such as CPU and DSA
links.
Also ds->ports is now a contiguous array of dsa_port structures, thus
their addresses cannot be NULL. Remove the useless check in
dsa_fastest_ageing_time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev VLAN filtering attribute setter from
the DSA slave device to the generic DSA port, so that the future
port-wide API can also be used for other port types, such as CPU and DSA
links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev VLAN object handlers from the DSA
slave device to the generic DSA port, so that the future port-wide API
can also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev MDB object handlers from the DSA slave
device to the generic DSA port, so that the future port-wide API can
also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the switchdev FDB object handlers from the DSA slave
device to the generic DSA port, so that the future port-wide API can
also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge join and leave functions only deal with a DSA port,
change their scope from the DSA slave net_device to the DSA generic
dsa_port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the scope of the fabric notification helper from the DSA slave to
the DSA port, since this is a DSA layer specific notion, that can be
used by non-slave ports (CPU and DSA).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having multiple STP state helpers scoping a slave device
supporting both the DSA logic and the switchdev binding, provide a
single dsa_port_set_state helper scoping a DSA port, as well as its
dsa_port_set_state_now wrapper which skips the prepare phase.
This allows us to better separate the DSA logic from the slave device
handling.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers and core use switchdev. Include switchdev.h only once, in
the dsa.h public header, so that inclusion in DSA drivers or forward
declarations of switchdev structures in not necessary anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The public include/net/dsa.h file is meant for DSA drivers, while all
DSA core files share a common private header net/dsa/dsa_priv.h file.
Ensure that dsa_priv.h is the only DSA core file to include net/dsa.h,
and add a new line to separate absolute and relative headers at the same
time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With more tag protocols being added, regain some order by sorting the
entries in various places.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dsa_switch_tree instance holds a dsa_switch pointer and a port index
to identify the switch port to which the CPU is attached.
Now that the DSA layer has a dsa_port structure to hold this data, use
it to point the switch CPU port.
This patch simply substitutes s/dst->cpu_switch/dst->cpu_dp->ds/ and
s/dst->cpu_port/dst->cpu_dp->index/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tag_lan9303.c does check for a NULL dst but that's already checked by
dsa_switch_rcv() one layer above.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.
This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves as is the legacy DSA code from dsa.c to legacy.c,
except the few shared symbols which remain in dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA tag receive functions do strictly the same thing after they have located
the originating source port from their tag specific protocol:
- push ETH_HLEN bytes
- set pkt_type to PACKET_HOST
- call eth_type_trans()
- bump up counters
- call netif_receive_skb()
Factor all of that into dsa_switch_rcv(). This also makes us return a pointer to
a sk_buff, which makes us symetric with the xmit function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA tag receive functions need to unshare the skb before mangling it, move
this to the generic dsa_switch_rcv() function which will allow us to make the
tag receive function return their mangled skb without caring about freeing a
NULL skb.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_switch_rcv() already tests for dst == NULL, so there is no need to duplicate
the same check within the tag receive functions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 96567d5dac ("net: dsa: dsa2: Add basic support of devlink")
I see the following link error with CONFIG_NET_DSA=y and CONFIG_NET_DEVLINK=m:
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe226b): undefined reference to `devlink_alloc'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe2284): undefined reference to `devlink_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe243e): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24e1): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24fa): undefined reference to `devlink_port_type_eth_set'
net/built-in.o: In function 'dsa_dst_unapply.part.8':
dsa2.c:(.text.unlikely+0x345): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x36c): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x38e): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x3f2): undefined reference to 'devlink_unregister'
dsa2.c:(.text.unlikely+0x3fb): undefined reference to 'devlink_free'
Fix this by adding a dependency on MAY_USE_DEVLINK so that CONFIG_NET_DSA
get switched to be build as module when CONFIG_NET_DEVLINK=m.
Fixes: 96567d5dac ("net: dsa: dsa2: Add basic support of devlink")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce crosschip_bridge_{join,leave} operations in the dsa_switch_ops
structure, which can be used by switches supporting interconnection.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the switch and its ports with devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DSA switch driver cannot program an ageing time value due to it
being out-of-range, switchdev will raise a stack trace before failing.
To fix this, add ageing_time_min and ageing_time_max members to the
dsa_switch in order for the switch drivers to optionally specify their
supported ageing time limits.
The DSA core will now check for provided ageing time limits and return
-ERANGE from the switchdev prepare phase if the value is out-of-range.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ageing time is defined as unsigned int, so make
dsa_fastest_ageing_time return an unsigned int instead of int.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding switch.o to the list of DSA object files, we essentially
duplicated the previous obj-y line and just added switch.o, remove the
duplicate.
Fixes: f515f192ab ("net: dsa: add switch notifier")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_create() can fail, and dsa_user_port_unapply() will properly check
for the network device not being NULL before attempting to destroy it. We were
not setting the slave network device as NULL if dsa_slave_create() failed, so
we would later on be calling dsa_slave_destroy() on a now free'd and
unitialized network device, causing crashes in dsa_slave_destroy().
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to use the new DSA API with platform data. Most of the
code in net/dsa/dsa2.c does not rely so much on device_nodes and can get
the same information from platform_data instead.
We purposely do not support distributed configurations with platform
data, so drivers should be providing a pointer to a 'struct
dsa_chip_data' structure if they wish to communicate per-port layout.
Multiple CPUs port could potentially be supported and dsa_chip_data is
extended to receive up to one reference to an upstream network device
per port described by a dsa_chip_data structure.
dsa_dev_to_net_device() increments the network device's reference count,
so we intentionally call dev_put() to be consistent with the DT-enabled
path, until we have a generic notifier based solution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for using this function in net/dsa/dsa2.c, rename the function
to make its scope DSA specific, and export it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A slave device will now notify the switch fabric once its port is
bridged or unbridged, instead of calling directly its switch operations.
This code allows propagating cross-chip bridging events in the fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scope of the functions inside net/dsa/slave.c must be the slave
net_device pointer. Change to state setter helper accordingly to
simplify callers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error is returned during the bridging of a port in a
NETDEV_CHANGEUPPER event, net/core/dev.c rolls back the operation.
Be consistent and unassign dp->bridge_dev when this happens.
In the meantime, add comments to document this behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code handling the slave netdevice notifier call by
providing a dsa_slave_changeupper helper for NETDEV_CHANGEUPPER, and so
on (only this event is supported at the moment.)
Return NOTIFY_DONE when we did not care about an event, and NOTIFY_OK
when we were concerned but no error occurred, as the API suggests.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netdevice notifier block register code in slave.c and provide
helpers for dsa.c to register and unregister it.
At the same time, check for errors since (un)register_netdevice_notifier
may fail.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary plumbing at the slave network device level to have switch
drivers implement ndo_setup_tc() and most particularly the cls_matchall
classifier. We add support for two switch operations:
port_add_mirror and port_del_mirror() which configure, on a per-port
basis the mirror parameters requested from the cls_matchall classifier.
Code is largely borrowed from the Mellanox Spectrum switch driver.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for CFP/TCAMP in the bcm_sf2 driver add the
plumbing to call into driver specific {get,set}_rxnfc operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bridge_dev pointer from dsa_slave_priv to dsa_port so that DSA
drivers can access this information and remove the need to cache it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store a pointer to the dsa_port structure in the dsa_slave_priv
structure, instead of the switch/port index.
This will allow to store more information such as the bridge device,
needed in DSA drivers for multi-chip configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the physical switch instance and port index a DSA port belongs to to
the dsa_port structure.
That can be used later to retrieve information about a physical port
when configuring a switch fabric, or lighten up struct dsa_slave_priv.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains the number of ports. Use it where the
structure is valid instead of the DSA_MAX_PORTS value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the assignment of ports in _dsa_register_switch() closer to where
it is checked, no functional change. Re-order declarations to be
preserve the inverted christmas tree style.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that these functions take a device_node structure pointer
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing platform data, and therefore no valid
device_node pointer, make most DSA functions takes a pointer to a
dsa_port structure whenever possible. While at it, introduce a
dsa_port_is_valid() helper function which checks whether port->dn is
NULL or not at the moment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 448b4482c6 ("net: dsa: Add lockdep class to tx queues to avoid
lockdep splat") removed the netif_device_detach() call done in
dsa_slave_suspend() which is necessary, and paired with a corresponding
netif_device_attach(), bring it back.
Fixes: 448b4482c6 ("net: dsa: Add lockdep class to tx queues to avoid lockdep splat")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may be able to see invalid Broadcom tags when the hardware and drivers are
misconfigured, or just while exercising the error path. Instead of flooding
the console with messages, flat out drop the packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the wrong !, otherwise we get false positives about having
multiple CPU interfaces.
Fixes: b22de49086 ("net: dsa: store CPU switch structure in the tree")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check the return value of phy_connect_direct() in
dsa_slave_phy_connect() otherwise we may be continuing the
initialization of a slave network device with a PHY that already
attached somewhere else and which will soon be in error because the PHY
device is in error.
The conditions for such an error to occur are that we have a port of our
switch that is not disabled, and has the same port number as a PHY
address (say both 5) that can be probed using the DSA slave MII bus. We
end-up having this slave network device find a PHY at the same address
as our port number, and we try to attach to it.
A slave network (e.g: port 0) has already attached to our PHY device,
and we try to re-attach it with a different network device, but since we
ignore the error we would end-up initializating incorrect device
references by the time the slave network interface is opened.
The code has been (re)organized several times, making it hard to provide
an exact Fixes tag, this is a bugfix nonetheless.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA Ethernet switches are true Linux devices, the CPU
switch is not necessarily the first one. If its address is higher than
the second switch on the same MDIO bus, its index will be 1, not 0.
Avoid any confusion by using dst->cpu_switch instead of dst->ds[0].
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store a dsa_switch pointer to the CPU switch in the tree instead of only
its index. This avoids the need to initialize it to -1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a543ef479 ("net: dsa:
Implement ndo_get_phys_port_id") since it misuses the purpose of
ndo_get_phys_port_id(). We have ndo_get_phys_port_name() to do the
correct thing for us now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the physical port number of a DSA created network device using
ndo_get_phys_port_name().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the new DTS bindings for DSA (dsa2), the "ethernet" and "link"
phandles are respectively mandatory and exclusive to CPU port and DSA
link device tree nodes.
Simplify dsa2.c a bit by checking the presence of such phandle instead
of checking the redundant "label" property.
Then the Linux philosophy for Ethernet switch ports is to expose them to
userspace as standard NICs by default. Thus use the standard enumerated
"eth%d" device name if no "label" property is provided for a user port.
This allows to save DTS files from subjective net device names.
If one wants to rename an interface, udev rules can be used as usual.
Of course the current behavior is unchanged, and the optional "label"
property for user ports has precedence over the enumerated name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly possible to have non zero indexed switches being present
in a DSA switch tree, in such a case, we will be deferencing a NULL
pointer while dsa_cpu_port_ethtool_{setup,restore}. Be more defensive
and ensure that dst->ds[0] is valid before doing anything with it.
Fixes: 0c73c523cf ("net: dsa: Initialize CPU port ethtool ops per tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support for DSA Ethernet switch chips depends on TCP/IP networking,
thus explicit that HAVE_NET_DSA depends on INET.
DSA uses SWITCHDEV, thus select it instead of depending on it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making struct dsa_switch_ops const, encapsulate it
within a dsa_switch_driver which has a list pointer and a pointer to
dsa_switch_ops. This allows us to take the list_head pointer out of
dsa_switch_ops, which is written to by {un,}register_switch_driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Isolate the HWMON support in DSA in its own file. Currently only the
legacy DSA code is concerned.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_driver_version string is irrelevant and has not been bumped
since its introduction about 9 years ago. Kill it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there can be multiple dsa switches stacked together but
not all of devicetree nodes available at the time of calling
dsa_dst_parse(), EPROBE_DEFER can be returned by it. When this
happens, only the last dsa switch has to be deleted by
dsa_dst_del_ds(), but not the whole list, because next time linux
cames back to this function it will try to add only the last dsa
switch which returned EPROBE_DEFER.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "out" label in dsa_switch_setup_one() is useless, thus remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_get_phys_port_id() by returning the physical port number
of the switch this per-port DSA created network interface corresponds
to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on slave-setup errors and on slave destroy.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_parse_phandle() before
returning from dsa_slave_phy_setup().
Note that this also modifies the PHY priority so that any fixed-link
node is only parsed when no phy-handle is given, which is in accordance
with the common scheme for this.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
_dsa_register_switch() gets a dsa_switch_tree object either via
dsa_get_dst() or via dsa_add_dst(). Former path does not increase kref
in returned object (resulting into caller not owning a reference),
while later path does create a new object (resulting into caller owning
a reference).
The rest of _dsa_register_switch() assumes that it owns a reference, and
calls dsa_put_dst().
This causes a memory breakage if first switch in the tree initialized
successfully, but second failed to initialize. In particular, freed
dsa_swith_tree object is left referenced by switch that was initialized,
and later access to sysfs attributes of that switch cause OOPS.
To fix, need to add kref_get() call to dsa_get_dst().
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() when
registering and deregistering the fixed-link PHY-device.
Fixes: 39b0c70519 ("net: dsa: Allow configuration of CPU & DSA port
speeds/duplex")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These few drivers call ether_setup(), but have no ndo_change_mtu, and thus
were overlooked for changes to MTU range checking behavior. They
previously had no range checks, so for feature-parity, set their min_mtu
to 0 and max_mtu to ETH_MAX_MTU (65535), instead of the 68 and 1500
inherited from the ether_setup() changes. Fine-tuning can come after we get
back to full feature-parity here.
CC: netdev@vger.kernel.org
Reported-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
CC: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
CC: R Parameswaran <parameswaran.r7@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today the DSA drivers are in charge of flushing the MAC addresses
associated to a port when its STP state changes from Learning or
Forwarding, to Disabled or Blocking or Listening.
This makes the drivers more complex and hides the generic switch logic.
Introduce a new optional port_fast_age operation to dsa_switch_ops, to
move this logic to the DSA layer and keep drivers simple.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a void helper to set the STP state of a port, checking first if the
required routine is provided by the driver.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only 1 of the 3 drivers currently has a set_addr() operation. Make the
set_addr() callback optional to reduce the amount of empty stubs inside
the drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 83c0afaec7 ("net: dsa: Add new binding implementation")
has a duplicate invocation of the set_addr() operation callback. Remove one
of them.
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SWITCHDEV_OBJ_ID_PORT_MDB support to the DSA layer.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.
The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing switch drivers to implement system-wide
suspend/resume functions, export dsa_switch_suspend and
dsa_switch_resume() such that these are callable from the appropriate
driver specific suspend/resume functions.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function for DSA drivers to handle the switchdev
SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME attribute.
The ageing time is passed as milliseconds.
Also because we can have multiple logical bridges on top of a physical
switch and ageing time are switch-wide, call the driver function with
the fastest ageing time in use on the chip instead of the requested one.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/dsa/dsa2.c:680:6: warning:
symbol '_dsa_unregister_switch' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routing table of every switch in a tree is currently initialized to
all zeros. This is an issue since 0 is a valid port number.
Add a DSA_RTABLE_NONE=-1 constant to initialize the signed values of the
routing table pointing to other switches.
This fixes the device mapping of the mv88e6xxx driver where the port
pointing to the switch itself and to non-existent switches was wrongly
configured to be 0. It is now set to the expected 0xf value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can properly support multiple distinct trees in the system,
using a global variable: dsa_cpu_port_ethtool_ops is getting clobbered
as soon as the second switch tree gets probed, and we don't want that.
We need to move this to be dynamically allocated, and since we can't
really be comparing addresses anymore to determine first time
initialization versus any other times, just move this to dsa.c and
dsa2.c where the remainder of the dst/ds initialization happens.
The operations teardown restores the master netdev's ethtool_ops to its
original ethtool_ops pointer (typically within the Ethernet driver)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function: dsa_cpu_port_ethtool_init() which initializes a
custom ethtool_ops structure with custom DSA ethtool operations for CPU
ports. This is a preliminary change to move the initialization outside
of net/dsa/slave.c.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mimic what net/dsa/dsa.c does and provide a slave MII bus by default
which will be created if the driver implements a phy_read method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers rely on these two bitmasks to contain the correct values
for them to successfully probe and initialize at drv->setup() time,
calculate correct values to put in both masks as early as possible in
dsa_get_ports_dn().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we have multiples trees and switches with the same index, we
need to add another discriminating id: the switch tree.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing DSA binding has a number of limitations and problems. The
main problem is that it cannot represent a switch as a linux device,
hanging off some bus. It is limited to one CPU port. The DSA platform
device is artificial, and does not really represent hardware.
Implement a new binding which can be embedded into any type of node on
a bus to represent one switch device, and its links to other switches.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch may want to instantiate its own MDIO bus. Only do it
centrally if the switch has not already created one, and the read op
is implemented.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the two switch statements with an array lookup, and store the
result in the dsa tree structure. The drivers no longer need to know
the selected tag protocol, so remove it from the dsa switch structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to setup a single DSA/CPU port into a function of
its own, and export it, so it can be used by the new binding.
Similarly, refactor the destroy code into a function. When destroying
the ports, don't put the of node. They should be released at the end
along with the normal ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new binding will not have a chip data structure, it will place the
routing directly into the switch structure. To enable backwards
compatibility, copy the routing from the chip data into the switch
structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a maximum of four switches, the size of the routing table is the
same as the pointer to it. Removing it makes the code simpler.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the port device node structure into the port structure, from the
chip data. This information is needed in the next step of implementing
the new binding.
The chip data structure is used while parsing the whole old binding,
before the individual switch structures exist. With the new bindings,
this is reversed, the switches exist first, and the interconnections
between the switches is derived from the individual switch
bindings. Thus this chip data structure becomes unneeded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
eviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are going to be more per-port members added to the switch
structure. So add a port structure and move the netdev into it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data nr_chips is used when validating a received packet,
to ensure it comes from a know switch chip. The number of possible
switches is limited to DSA_MAX_SWITCHES, so use this as the first
validation step. The new binding allows holes in the dst->ds[] array,
so also ensure ensure there is a valid dsa_switch for this packet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer should no longer assume the switch is connected to an
MDIO bus. As a result, we cannot use the address on the MDIO bus when
forming the name of the switches internal MDIO bus for its builtin and
possibly external PHYs. The switch index is sufficient to make the
name unique, so drop the MDIO address.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new binding does not make use of dsa_chip_data, a.k.a cd. When
retrieving the size of the EEPROM attached to a switch, don't assume
there is a cd attached to the switch structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch overloads the DSA master netdev, aka CPU Ethernet MAC to also
include switch-side statistics, which is useful for debugging purposes,
when the switch is not properly connected to the Ethernet MAC (duplex
mismatch, (RG)MII electrical issues etc.).
We accomplish this by retaining the original copy of the master netdev's
ethtool_ops, and just overload the 3 operations we care about:
get_sset_count, get_strings and get_ethtool_stats so as to intercept
these calls and call into the original master_netdev ethtool_ops, plus
our own.
We take this approach as opposed to providing a set of DSA helper
functions that would retrive the CPU port's statistics, because the
entire purpose of DSA is to allow unmodified Ethernet MAC drivers to be
used as CPU conduit interfaces, therefore, statistics overlay in such
drivers would simply not scale.
The new ethtool -S <iface> output would therefore look like this now:
<iface> statistics
p<2 digits cpu port number>_<switch MIB counter names>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the tag protocol in dsa_switch_driver for setup time and in
dsa_switch_tree for runtime is enough. Remove dsa_switch's one.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_slave_priv structure does not need a pointer to its net_device.
Kill it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the dsa_switch_driver.probe function to return a const char *.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
