Commit c3ae62af8e ("tcp: should drop incoming frames without ACK
flag set") was created to mitigate a security vulnerability in which a
local attacker is able to inject data into locally-opened sockets by
using TCP protocol statistics in procfs to quickly find the correct
sequence number.
This broke the RFC5961 requirement to send a challenge ACK in response
to spurious RST packets, which was subsequently fixed by commit
7b514a886b ("tcp: accept RST without ACK flag").
Unfortunately, the RFC5961 requirement that spurious SYN packets be
handled in a similar manner remains broken.
RFC5961 section 4 states that:
... the handling of the SYN in the synchronized state SHOULD be
performed as follows:
1) If the SYN bit is set, irrespective of the sequence number, TCP
MUST send an ACK (also referred to as challenge ACK) to the remote
peer:
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
After sending the acknowledgment, TCP MUST drop the unacceptable
segment and stop processing further.
By sending an ACK, the remote peer is challenged to confirm the loss
of the previous connection and the request to start a new connection.
A legitimate peer, after restart, would not have a TCB in the
synchronized state. Thus, when the ACK arrives, the peer should send
a RST segment back with the sequence number derived from the ACK
field that caused the RST.
This RST will confirm that the remote peer has indeed closed the
previous connection. Upon receipt of a valid RST, the local TCP
endpoint MUST terminate its connection. The local TCP endpoint
should then rely on SYN retransmission from the remote end to
re-establish the connection.
This patch lets SYN packets through the discard added in c3ae62af8e,
so that spurious SYN packets are properly dealt with as per the RFC.
The challenge ACK is sent unconditionally and is rate-limited, so the
original vulnerability is not reintroduced by this patch.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use them to push skb->vlan_tci into the payload and avoid code
duplication.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name fits better. Plus there's going to be introduced
__vlan_insert_tag later on.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on sk_forward_alloc problems reported by Denys
Fedoryshchenko, we found that tcp connect() (and fastopen) do not call
sk_wmem_schedule() for SYN packet (and/or SYN/DATA packet), so
sk_forward_alloc is negative while connect is in progress.
We can fix this by calling regular sk_stream_alloc_skb() both for the
SYN packet (in tcp_connect()) and the syn_data packet in
tcp_send_syn_data()
Then, tcp_send_syn_data() can avoid copying syn_data as we simply
can manipulate syn_data->cb[] to remove SYN flag (and increment seq)
Instead of open coding memcpy_fromiovecend(), simply use this helper.
This leaves in socket write queue clean fast clone skbs.
This was tested against our fastopen packetdrill tests.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If icmp_rcv() has successfully processed the incoming ICMP datagram, we
should use consume_skb() rather than kfree_skb() because a hit on the likes
of perf -e skb:kfree_skb is not called-for.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that generating an MLD listener report on
devices with large MTUs (e.g. 9000) and a high number of IPv6
addresses can trigger a skb_over_panic():
skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20
head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0
dev:port1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:100!
invalid opcode: 0000 [#1] SMP
Modules linked in: ixgbe(O)
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4
[...]
Call Trace:
<IRQ>
[<ffffffff80578226>] ? skb_put+0x3a/0x3b
[<ffffffff80612a5d>] ? add_grhead+0x45/0x8e
[<ffffffff80612e3a>] ? add_grec+0x394/0x3d4
[<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d
[<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45
[<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68
[<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182
[<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d
[<ffffffff8025112b>] ? irq_exit+0x4e/0xd3
[<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46
[<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70
mld_newpack() skb allocations are usually requested with dev->mtu
in size, since commit 72e09ad107 ("ipv6: avoid high order allocations")
we have changed the limit in order to be less likely to fail.
However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb)
macros, which determine if we may end up doing an skb_put() for
adding another record. To avoid possible fragmentation, we check
the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong
assumption as the actual max allocation size can be much smaller.
The IGMP case doesn't have this issue as commit 57e1ab6ead
("igmp: refine skb allocations") stores the allocation size in
the cb[].
Set a reserved_tailroom to make it fit into the MTU and use
skb_availroom() helper instead. This also allows to get rid of
igmp_skb_size().
Reported-by: Wei Liu <lw1a2.jing@gmail.com>
Fixes: 72e09ad107 ("ipv6: avoid high order allocations")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: David L Stevens <david.stevens@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter updates for your net tree,
they are:
1) Fix missing initialization of the range structure (allocated in the
stack) in nft_masq_{ipv4, ipv6}_eval, from Daniel Borkmann.
2) Make sure the data we receive from userspace contains the req_version
structure, otherwise return an error incomplete on truncated input.
From Dan Carpenter.
3) Fix handling og skb->sk which may cause incorrect handling
of connections from a local process. Via Simon Horman, patch from
Calvin Owens.
4) Fix wrong netns in nft_compat when setting target and match params
structure.
5) Relax chain type validation in nft_compat that was recently included,
this broke the matches that need to be run from the route chain type.
Now iptables-test.py automated regression tests report success again
and we avoid the only possible problematic case, which is the use of
nat targets out of nat chain type.
6) Use match->table to validate the tablename, instead of the match->name.
Again patch for nft_compat.
7) Restore the synchronous release of objects from the commit and abort
path in nf_tables. This is causing two major problems: splats when using
nft_compat, given that matches and targets may sleep and call_rcu is
invoked from softirq context. Moreover Patrick reported possible event
notification reordering when rules refer to anonymous sets.
8) Fix race condition in between packets that are being confirmed by
conntrack and the ctnetlink flush operation. This happens since the
removal of the central spinlock. Thanks to Jesper D. Brouer to looking
into this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to add an unreachable route incorrectly returns -ESRCH if
if custom FIB rules are present:
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: Network is unreachable
[root@localhost ~]# ip rule add to 55.66.77.88 table 200
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: No such process
[root@localhost ~]#
Commit 83886b6b63 ("[NET]: Change "not found"
return value for rule lookup") changed fib_rules_lookup()
to use -ESRCH as a "not found" code internally, but for user space it
should be translated into -ENETUNREACH. Handle the translation centrally in
ipv4-specific fib_lookup(), leaving the DECnet case alone.
On a related note, commit b7a71b51ee
("ipv4: removed redundant conditional") removed a similar translation from
ip_route_input_slow() prematurely AIUI.
Fixes: b7a71b51ee ("ipv4: removed redundant conditional")
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In DC world, GSO packets initially cooked by tcp_sendmsg() are usually
big, as sk_pacing_rate is high.
When network is congested, cwnd can be smaller than the GSO packets
found in socket write queue. tcp_write_xmit() splits GSO packets
using the available cwnd, and we end up sending a single GSO packet,
consuming all available cwnd.
With GRO aggregation on the receiver, we might handle a single GRO
packet, sending back a single ACK.
1) This single ACK might be lost
TLP or RTO are forced to attempt a retransmit.
2) This ACK releases a full cwnd, sender sends another big GSO packet,
in a ping pong mode.
This behavior does not fill the pipes in the best way, because of
scheduling artifacts.
Make sure we always have at least two GSO packets in flight.
This allows us to safely increase GRO efficiency without risking
spurious retransmits.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/fou.c: In function ‘ip_tunnel_encap_del_fou_ops’:
net/ipv4/fou.c:861:1: warning: no return statement in function returning non-void [-Wreturn-type]
Fixes: a8c5f90fb5 ("ip_tunnel: Ops registration for secondary encap (fou, gue)")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/bridge/br_netfilter.c:870:6: symbol 'br_netfilter_enable' was not declared. Should it be static?
no; add include
net/ipv4/netfilter/nft_reject_ipv4.c:22:6: symbol 'nft_reject_ipv4_eval' was not declared. Should it be static?
yes
net/ipv6/netfilter/nf_reject_ipv6.c:16:6: symbol 'nf_send_reset6' was not declared. Should it be static?
no; add include
net/ipv6/netfilter/nft_reject_ipv6.c:22:6: symbol 'nft_reject_ipv6_eval' was not declared. Should it be static?
yes
net/netfilter/core.c:33:32: symbol 'nf_ipv6_ops' was not declared. Should it be static?
no; add include
net/netfilter/xt_DSCP.c:40:57: cast truncates bits from constant value (ffffff03 becomes 3)
net/netfilter/xt_DSCP.c:57:59: cast truncates bits from constant value (ffffff03 becomes 3)
add __force, 3 is what we want.
net/ipv4/netfilter/nf_log_arp.c:77:6: symbol 'nf_log_arp_packet' was not declared. Should it be static?
yes
net/ipv4/netfilter/nf_reject_ipv4.c:17:6: symbol 'nf_send_reset' was not declared. Should it be static?
no; add include
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of calling fou and gue functions directly from ip_tunnel
use ops for these that were previously registered. This patch adds the
logic to add and remove encapsulation operations for ip_tunnel,
and modified fou (and gue) to register with ip_tunnels.
This patch also addresses a circular dependency between ip_tunnel
and fou that was causing link errors when CONFIG_NET_IP_TUNNEL=y
and CONFIG_NET_FOU=m. References to fou an gue have been removed from
ip_tunnel.c
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Standardize function pointer uses.
Convert calling style from:
(*foo)(args...);
to:
foo(args...);
Other miscellanea:
o Add braces around loops with single ifs on multiple lines
o Realign arguments around these functions
o Invert logic in if to return immediately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IS_ENABLED(CONFIG_IPV6), to enable this code if IPv6 is
a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: c8e6ad0829 ("ipv6: honor IPV6_PKTINFO with v4 mapped addresses on sendmsg")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are only three neigh tables in the whole kernel:
arp table, ndisc table and decnet neigh table. What's more,
we don't support registering multiple tables per family.
Therefore we can just make these tables statically built-in.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alternative to RPS/RFS is to use hardware support for multiple
queues.
Then split a set of million of sockets into worker threads, each
one using epoll() to manage events on its own socket pool.
Ideally, we want one thread per RX/TX queue/cpu, but we have no way to
know after accept() or connect() on which queue/cpu a socket is managed.
We normally use one cpu per RX queue (IRQ smp_affinity being properly
set), so remembering on socket structure which cpu delivered last packet
is enough to solve the problem.
After accept(), connect(), or even file descriptor passing around
processes, applications can use :
int cpu;
socklen_t len = sizeof(cpu);
getsockopt(fd, SOL_SOCKET, SO_INCOMING_CPU, &cpu, &len);
And use this information to put the socket into the right silo
for optimal performance, as all networking stack should run
on the appropriate cpu, without need to send IPI (RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_mark_napi_id() is used to record for a flow napi id of incoming
packets for busypoll sake.
We should do this only on established flows, not on listeners.
This was 'working' by virtue of the socket cloning, but doing
this on SYN packets in unecessary cache line dirtying.
Even if we move sk_napi_id in the same cache line than sk_lock,
we are working to make SYN processing lockless, so it is desirable
to set sk_napi_id only for established flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing GRO processing for UDP tunnels, we never add
SKB_GSO_UDP_TUNNEL to gso_type - only the type of the inner protocol
is added (such as SKB_GSO_TCPV4). The result is that if the packet is
later resegmented we will do GSO but not treat it as a tunnel. This
results in UDP fragmentation of the outer header instead of (i.e.) TCP
segmentation of the inner header as was originally on the wire.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since raw_probe_proto_opt was added it had the problem of
causing the user iov to be read twice, once during the probe for
the protocol header and once again in ip_append_data.
This is a potential security problem since it means that whatever
we're probing may be invalid. This patch plugs the hole by
firstly advancing the iov so we don't read the same spot again,
and secondly saving what we read the first time around for use
by ip_append_data.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function raw_probe_proto_opt tries to extract the first two
bytes from the user input in order to seed the IPsec lookup for
ICMP packets. In doing so it's processing iovec by hand and
overcomplicating things.
This patch replaces the manual iovec processing with a call to
memcpy_fromiovecend.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transferring from the original range in nf_nat_masquerade_{ipv4,ipv6}()
we copy over values from stack in from min_proto/max_proto due to uninitialized
range variable in both, nft_masq_{ipv4,ipv6}_eval. As we only initialize
flags at this time from nft_masq struct, just zero out the rest.
Fixes: 9ba1f726be ("netfilter: nf_tables: add new nft_masq expression")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As NIC multicast filtering isn't perfect, and some platforms are
quite content to spew broadcasts, we should not trigger an event
for skb:kfree_skb when we do not have a match for such an incoming
datagram. We do though want to avoid sweeping the matter under the
rug entirely, so increment a suitable statistic.
This incorporates feedback from David L. Stevens, Karl Neiss and Eric
Dumazet.
V3 - use bool per David Miller
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
Open vSwitch
First two patches are related to OVS MPLS support. Rest of patches
are mostly refactoring and minor improvements to openvswitch.
v1-v2:
- Fix conflicts due to "gue: Remote checksum offload"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 64ce207306 ("[NET]: Make NETDEBUG pure printk wrappers")
originally had these NETDEBUG printks as always emitting.
Commit a2a316fd06 ("[NET]: Replace CONFIG_NET_DEBUG with sysctl")
added a net_msg_warn sysctl to these NETDEBUG uses.
Convert these NETDEBUG uses to normal pr_info calls.
This changes the output prefix from "ESP: " to include
"IPSec: " for the ipv4 case and "IPv6: " for the ipv6 case.
These output lines are now like the other messages in the files.
Other miscellanea:
Neaten the arithmetic spacing to be consistent with other
arithmetic spacing in the files.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages aren't useful as there's a generic dump_stack()
on OOM.
Neaten the comment and if test above the OOM by separating the
assign in if into an allocation then if test.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device can export MPLS GSO support in dev->mpls_features same way
it export vlan features in dev->vlan_features. So it is safe to
remove NETIF_F_GSO_MPLS redundant flag.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
When filling netlink info, dport is being returned as flags. Fix
instances to return correct value.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that generating an MLD listener report on
devices with large MTUs (e.g. 9000) and a high number of IPv6
addresses can trigger a skb_over_panic():
skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20
head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0
dev:port1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:100!
invalid opcode: 0000 [#1] SMP
Modules linked in: ixgbe(O)
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4
[...]
Call Trace:
<IRQ>
[<ffffffff80578226>] ? skb_put+0x3a/0x3b
[<ffffffff80612a5d>] ? add_grhead+0x45/0x8e
[<ffffffff80612e3a>] ? add_grec+0x394/0x3d4
[<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d
[<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45
[<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68
[<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182
[<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d
[<ffffffff8025112b>] ? irq_exit+0x4e/0xd3
[<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46
[<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70
mld_newpack() skb allocations are usually requested with dev->mtu
in size, since commit 72e09ad107 ("ipv6: avoid high order allocations")
we have changed the limit in order to be less likely to fail.
However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb)
macros, which determine if we may end up doing an skb_put() for
adding another record. To avoid possible fragmentation, we check
the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong
assumption as the actual max allocation size can be much smaller.
The IGMP case doesn't have this issue as commit 57e1ab6ead
("igmp: refine skb allocations") stores the allocation size in
the cb[].
Set a reserved_tailroom to make it fit into the MTU and use
skb_availroom() helper instead. This also allows to get rid of
igmp_skb_size().
Reported-by: Wei Liu <lw1a2.jing@gmail.com>
Fixes: 72e09ad107 ("ipv6: avoid high order allocations")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: David L Stevens <david.stevens@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a single fixed string is smaller code size than using
a format and many string arguments.
Reduces overall code size a little.
$ size net/ipv4/igmp.o* net/ipv6/mcast.o* net/ipv6/ip6_flowlabel.o*
text data bss dec hex filename
34269 7012 14824 56105 db29 net/ipv4/igmp.o.new
34315 7012 14824 56151 db57 net/ipv4/igmp.o.old
30078 7869 13200 51147 c7cb net/ipv6/mcast.o.new
30105 7869 13200 51174 c7e6 net/ipv6/mcast.o.old
11434 3748 8580 23762 5cd2 net/ipv6/ip6_flowlabel.o.new
11491 3748 8580 23819 5d0b net/ipv6/ip6_flowlabel.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ueki Kohei reported that when we are using NewReno with connections that
have a very low traffic, we may timeout the connection too early if a
second loss occurs after the first one was successfully acked but no
data was transfered later. Below is his description of it:
When SACK is disabled, and a socket suffers multiple separate TCP
retransmissions, that socket's ETIMEDOUT value is calculated from the
time of the *first* retransmission instead of the *latest*
retransmission.
This happens because the tcp_sock's retrans_stamp is set once then never
cleared.
Take the following connection:
Linux remote-machine
| |
send#1---->(*1)|--------> data#1 --------->|
| | |
RTO : :
| | |
---(*2)|----> data#1(retrans) ---->|
| (*3)|<---------- ACK <----------|
| | |
| : :
| : :
| : :
16 minutes (or more) :
| : :
| : :
| : :
| | |
send#2---->(*4)|--------> data#2 --------->|
| | |
RTO : :
| | |
---(*5)|----> data#2(retrans) ---->|
| | |
| | |
RTO*2 : :
| | |
| | |
ETIMEDOUT<----(*6)| |
(*1) One data packet sent.
(*2) Because no ACK packet is received, the packet is retransmitted.
(*3) The ACK packet is received. The transmitted packet is acknowledged.
At this point the first "retransmission event" has passed and been
recovered from. Any future retransmission is a completely new "event".
(*4) After 16 minutes (to correspond with retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and (*4).
The socket's timeout SHOULD be calculated from this point in time, but
instead it's calculated from the prior "event" 16 minutes ago.
(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT.
Therefore, now we clear retrans_stamp as soon as all data during the
loss window is fully acked.
Reported-by: Ueki Kohei
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".
When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.
Having a helper like this means there will be less places to touch
during that transformation.
Based upon descriptions and patch from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add processing of the remote checksum offload option in both the normal
path as well as the GRO path. The implements patching the affected
checksum to derive the offloaded checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add if_tunnel flag TUNNEL_ENCAP_FLAG_REMCSUM to configure
remote checksum offload on an IP tunnel. Add logic in gue_build_header
to insert remote checksum offload option.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new GSO type, SKB_GSO_TUNNEL_REMCSUM, which indicates remote
checksum offload being done (in this case inner checksum must not
be offloaded to the NIC).
Added logic in __skb_udp_tunnel_segment to handle remote checksum
offload case.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions and basic definitions for processing standard flags,
private flags, and control messages. This includes definitions
to compute length of optional fields corresponding to a set of flags.
Flag validation is in validate_gue_flags function. This checks for
unknown flags, and that length of optional fields is <= length
in guehdr hlen.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __skb_udp_tunnel_segment if outer UDP checksums are enabled and
ip_summed is not already CHECKSUM_PARTIAL, set up checksum offload
if device features allow it.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move fou_build_header out of ip_tunnel.c and into fou.c splitting
it up into fou_build_header, gue_build_header, and fou_build_udp.
This allows for other users for TX of FOU or GUE. Change ip_tunnel_encap
to call fou_build_header or gue_build_header based on the tunnel
encapsulation type. Similarly, added fou_encap_hlen and gue_encap_hlen
functions which are called by ip_encap_hlen. New net/fou.h has
prototypes and defines for this.
Added NET_FOU_IP_TUNNELS configuration. When this is set, IP tunnels
can use FOU/GUE and fou module is also selected.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pernet ops aren't ever unregistered, which causes a memory
leak and an OOPs if the module is ever reinserted.
Fixes: 0b5e8b8eea ("net: Add Geneve tunneling protocol driver")
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geneve does not currently set the inner protocol type when
transmitting packets. This causes GSO segmentation to fail on NICs
that do not support Geneve offloading.
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of seq_printf() is soon to be removed. Remove the
checks from seq_printf() in favor of seq_has_overflowed().
Link: http://lkml.kernel.org/r/20141104142236.GA10239@salvia
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: netfilter-devel@vger.kernel.org
Cc: coreteam@netfilter.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Since adding a new function to seq_file (seq_has_overflowed())
there isn't any value for functions called from seq_show to
return anything. Remove the int returns of the various
print_tuple/<foo>_print_tuple functions.
Link: http://lkml.kernel.org/p/f2e8cf8df433a197daa62cbaf124c900c708edc7.1412031505.git.joe@perches.com
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: netfilter-devel@vger.kernel.org
Cc: coreteam@netfilter.org
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The seq_printf() and friends are having their return values removed.
The print_conntrack() returns the result of seq_printf(), which is
meaningless when seq_printf() returns void. Might as well remove the
return values of print_conntrack() as well.
Link: http://lkml.kernel.org/r/20141029220107.465008329@goodmis.org
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: netfilter-devel@vger.kernel.org
Cc: coreteam@netfilter.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch allows to set ECN on a per-route basis in case the sysctl
tcp_ecn is not set to 1. In other words, when ECN is set for specific
routes, it provides a tcp_ecn=1 behaviour for that route while the rest
of the stack acts according to the global settings.
One can use 'ip route change dev $dev $net features ecn' to toggle this.
Having a more fine-grained per-route setting can be beneficial for various
reasons, for example, 1) within data centers, or 2) local ISPs may deploy
ECN support for their own video/streaming services [1], etc.
There was a recent measurement study/paper [2] which scanned the Alexa's
publicly available top million websites list from a vantage point in US,
Europe and Asia:
Half of the Alexa list will now happily use ECN (tcp_ecn=2, most likely
blamed to commit 255cac91c3 ("tcp: extend ECN sysctl to allow server-side
only ECN") ;)); the break in connectivity on-path was found is about
1 in 10,000 cases. Timeouts rather than receiving back RSTs were much
more common in the negotiation phase (and mostly seen in the Alexa
middle band, ranks around 50k-150k): from 12-thousand hosts on which
there _may_ be ECN-linked connection failures, only 79 failed with RST
when _not_ failing with RST when ECN is not requested.
It's unclear though, how much equipment in the wild actually marks CE
when buffers start to fill up.
We thought about a fallback to non-ECN for retransmitted SYNs as another
global option (which could perhaps one day be made default), but as Eric
points out, there's much more work needed to detect broken middleboxes.
Two examples Eric mentioned are buggy firewalls that accept only a single
SYN per flow, and middleboxes that successfully let an ECN flow establish,
but later mark CE for all packets (so cwnd converges to 1).
[1] http://www.ietf.org/proceedings/89/slides/slides-89-tsvarea-1.pdf, p.15
[2] http://ecn.ethz.ch/
Joint work with Daniel Borkmann.
Reference: http://thread.gmane.org/gmane.linux.network/335797
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function cookie_check_timestamp(), both called from IPv4/6 context,
is being used to decode the echoed timestamp from the SYN/ACK into TCP
options used for follow-up communication with the peer.
We can remove ECN handling from that function, split it into a separate
one, and simply rename the original function into cookie_decode_options().
cookie_decode_options() just fills in tcp_option struct based on the
echoed timestamp received from the peer. Anything that fails in this
function will actually discard the request socket.
While this is the natural place for decoding options such as ECN which
commit 172d69e63c ("syncookies: add support for ECN") added, we argue
that in particular for ECN handling, it can be checked at a later point
in time as the request sock would actually not need to be dropped from
this, but just ECN support turned off.
Therefore, we split this functionality into cookie_ecn_ok(), which tells
us if the timestamp indicates ECN support AND the tcp_ecn sysctl is enabled.
This prepares for per-route ECN support: just looking at the tcp_ecn sysctl
won't be enough anymore at that point; if the timestamp indicates ECN
and sysctl tcp_ecn == 0, we will also need to check the ECN dst metric.
This would mean adding a route lookup to cookie_check_timestamp(), which
we definitely want to avoid. As we already do a route lookup at a later
point in cookie_{v4,v6}_check(), we can simply make use of that as well
for the new cookie_ecn_ok() function w/o any additional cost.
Joint work with Daniel Borkmann.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Was a bit more difficult to read than needed due to magic shifts;
add defines and document the used encoding scheme.
Joint work with Daniel Borkmann.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
else is unnecessary after return 0 in __udp4_lib_rcv()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove __inline__ / inline and let compiler decide what to do
with static functions
Inspired-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/ipvs fixes for net
The following patchset contains fixes for netfilter/ipvs. This round of
fixes is larger than usual at this stage, specifically because of the
nf_tables bridge reject fixes that I would like to see in 3.18. The
patches are:
1) Fix a null-pointer dereference that may occur when logging
errors. This problem was introduced by 4a4739d56b ("ipvs: Pull
out crosses_local_route_boundary logic") in v3.17-rc5.
2) Update hook mask in nft_reject_bridge so we can also filter out
packets from there. This fixes 36d2af5 ("netfilter: nf_tables: allow
to filter from prerouting and postrouting"), which needs this chunk
to work.
3) Two patches to refactor common code to forge the IPv4 and IPv6
reject packets from the bridge. These are required by the nf_tables
reject bridge fix.
4) Fix nft_reject_bridge by avoiding the use of the IP stack to reject
packets from the bridge. The idea is to forge the reject packets and
inject them to the original port via br_deliver() which is now
exported for that purpose.
5) Restrict nft_reject_bridge to bridge prerouting and input hooks.
the original skbuff may cloned after prerouting when the bridge stack
needs to flood it to several bridge ports, it is too late to reject
the traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_iphdr_put(): to build the IPv4 header.
* nf_reject_ip_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some drivers are unable to perform TX completions in a bound time.
They instead call skb_orphan()
Problem is skb_fclone_busy() has to detect this case, otherwise
we block TCP retransmits and can freeze unlucky tcp sessions on
mostly idle hosts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1f3279ae0c ("tcp: avoid retransmits of TCP packets hanging in host queues")
Signed-off-by: David S. Miller <davem@davemloft.net>
Challenge ACK is described in RFC 5961, fix typo.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb_inner_network_header is used but this does not account
for Ethernet header for ETH_P_TEB. Use skb_inner_mac_header which
handles TEB and also should work with IP encapsulation in which case
inner mac and inner network headers are the same.
Tested: Ran TCP_STREAM over GRE, worked as expected.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we cache them, the kernel will reuse them, independently of
whether forwarding is enabled or not. Which means that if forwarding is
disabled on the input interface where the first routing request comes
from, then that unreachable result will be cached and reused for
other interfaces, even if forwarding is enabled on them. The opposite
is also true.
This can be verified with two interfaces A and B and an output interface
C, where B has forwarding enabled, but not A and trying
ip route get $dst iif A from $src && ip route get $dst iif B from $src
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only count packets that failed cookie-authentication.
We can get SYNCOOKIESFAILED > 0 while we never even sent a single cookie.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, despite the comment right before the function,
nf_log_register allows registering two loggers on with the same type and
end up overwriting the previous register.
Not a real issue today as current tree doesn't have two loggers for the
same type but it's better to get this protected.
Also make sure that all of its callers do error checking.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The WARN_ON in inet_evict_bucket can be triggered by a valid case:
inet_frag_kill and inet_evict_bucket can be running in parallel on the
same queue which means that there has been at least one more ref added
by a previous inet_frag_find call, but inet_frag_kill can delete the
timer before inet_evict_bucket which will cause the WARN_ON() there to
trigger since we'll have refcnt!=1. Now, this case is valid because the
queue is being "killed" for some reason (removed from the chain list and
its timer deleted) so it will get destroyed in the end by one of the
inet_frag_put() calls which reaches 0 i.e. refcnt is still valid.
CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the evictor is running it adds some chosen frags to a local list to
be evicted once the chain lock has been released but at the same time
the *frag_queue can be running for some of the same queues and it
may call inet_frag_kill which will wait on the chain lock and
will then delete the queue from the wrong list since it was added in the
eviction one. The fix is simple - check if the queue has the evict flag
set under the chain lock before deleting it, this is safe because the
evict flag is set only under that lock and having the flag set also means
that the queue has been detached from the chain list, so no need to delete
it again.
An important note to make is that we're safe w.r.t refcnt because
inet_frag_kill and inet_evict_bucket will sync on the del_timer operation
where only one of the two can succeed (or if the timer is executing -
none of them), the cases are:
1. inet_frag_kill succeeds in del_timer
- then the timer ref is removed, but inet_evict_bucket will not add
this queue to its expire list but will restart eviction in that chain
2. inet_evict_bucket succeeds in del_timer
- then the timer ref is kept until the evictor "expires" the queue, but
inet_frag_kill will remove the initial ref and will set
INET_FRAG_COMPLETE which will make the frag_expire fn just to remove
its ref.
In the end all of the queue users will do an inet_frag_put and the one
that reaches 0 will free it. The refcount balance should be okay.
CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Tested-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing upcoming Yaogong patch (converting out of order queue
into an RB tree), I hit the max reordering level of linux TCP stack.
Reordering level was limited to 127 for no good reason, and some
network setups [1] can easily reach this limit and get limited
throughput.
Allow a new max limit of 300, and add a sysctl to allow admins to even
allow bigger (or lower) values if needed.
[1] Aggregation of links, per packet load balancing, fabrics not doing
deep packet inspections, alternative TCP congestion modules...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new expression provides NAT in the redirect flavour, which is to
redirect packets to local machine.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch refactors the IPv4 code so it can be usable both from xt and
nf_tables.
A similar patch follows-up to handle IPv6.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
unsigned char *sha (source) was already in original git version
but was never used.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu tcp_md5sig_pool contains memory blobs that ultimately
go through sg_set_buf().
-> sg_set_page(sg, virt_to_page(buf), buflen, offset_in_page(buf));
This requires that whole area is in a physically contiguous portion
of memory. And that @buf is not backed by vmalloc().
Given that alloc_percpu() can use vmalloc() areas, this does not
fit the requirements.
Replace alloc_percpu() by a static DEFINE_PER_CPU() as tcp_md5sig_pool
is small anyway, there is no gain to dynamically allocate it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 765cf9976e ("tcp: md5: remove one indirection level in tcp_md5sig_pool")
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit "net: Save TX flow hash in sock and set in skbuf on xmit"
introduced the inet_set_txhash() and ip6_set_txhash() routines to calculate
and record flow hash(sk_txhash) in the socket structure. sk_txhash is used
to set skb->hash which is used to spread flows across multiple TXQs.
But, the above routines are invoked before the source port of the connection
is created. Because of this all outgoing connections that just differ in the
source port get hashed into the same TXQ.
This patch fixes this problem for IPv4/6 by invoking the the above routines
after the source port is available for the socket.
Fixes: b73c3d0e4("net: Save TX flow hash in sock and set in skbuf on xmit")
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_segment has three possible return values:
1. a pointer to the first segmented skb
2. an errno value (IS_ERR())
3. NULL. This can happen when GSO is used for header verification.
However, several callers currently test IS_ERR instead of IS_ERR_OR_NULL
and would oops when NULL is returned.
Note that these call sites should never actually see such a NULL return
value; all callers mask out the GSO bits in the feature argument.
However, there have been issues with some protocol handlers erronously not
respecting the specified feature mask in some cases.
It is preferable to get 'have to turn off hw offloading, else slow' reports
rather than 'kernel crashes'.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_segment() has a 'features' argument representing offload features
available to the output path.
A few handlers, e.g. GRE, instead re-fetch the features of skb->dev and use
those instead of the provided ones when handing encapsulation/tunnels.
Depending on dev->hw_enc_features of the output device skb_gso_segment() can
then return NULL even when the caller has disabled all GSO feature bits,
as segmentation of inner header thinks device will take care of segmentation.
This e.g. affects the tbf scheduler, which will silently drop GRE-encap GSO skbs
that did not fit the remaining token quota as the segmentation does not work
when device supports corresponding hw offload capabilities.
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter fixes for net
The following patchset contains netfilter fixes for your net tree,
they are:
1) Fix missing MODULE_LICENSE() in the new nf_reject_ipv{4,6} modules.
2) Restrict nat and masq expressions to the nat chain type. Otherwise,
users may crash their kernel if they attach a nat/masq rule to a non
nat chain.
3) Fix hook validation in nft_compat when non-base chains are used.
Basically, initialize hook_mask to zero.
4) Make sure you use match/targets in nft_compat from the right chain
type. The existing validation relies on the table name which can be
avoided by
5) Better netlink attribute validation in nft_nat. This expression has
to reject the configuration when no address and proto configurations
are specified.
6) Interpret NFTA_NAT_REG_*_MAX if only if NFTA_NAT_REG_*_MIN is set.
Yet another sanity check to reject incorrect configurations from
userspace.
7) Conditional NAT attribute dumping depending on the existing
configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A quick batch of bug fixes:
1) Fix build with IPV6 disabled, from Eric Dumazet.
2) Several more cases of caching SKB data pointers across calls to
pskb_may_pull(), thus referencing potentially free'd memory. From
Li RongQing.
3) DSA phy code tests operation presence improperly, instead of going:
if (x->ops->foo)
r = x->ops->foo(args);
it was going:
if (x->ops->foo(args))
r = x->ops->foo(args);
Fix from Andew Lunn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
Net: DSA: Fix checking for get_phy_flags function
ipv6: fix a potential use after free in sit.c
ipv6: fix a potential use after free in ip6_offload.c
ipv4: fix a potential use after free in gre_offload.c
tcp: fix build error if IPv6 is not enabled
pskb_may_pull() may change skb->data and make greh pointer oboslete;
so need to reassign greh;
but since first calling pskb_may_pull already ensured that skb->data
has enough space for greh, so move the reference of greh before second
calling pskb_may_pull(), to avoid reassign greh.
Fixes: 7a7ffbabf9("ipv4: fix tunneled VM traffic over hw VXLAN/GRE GSO NIC")
Cc: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
pskb_may_pull() maybe change skb->data and make uh pointer oboslete,
so reload uh and guehdr
Fixes: 37dd0247 ("gue: Receive side for Generic UDP Encapsulation")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull() maybe change skb->data and make eth pointer oboslete,
so set eth after pskb_may_pull()
Fixes:3d7b46cd("ip_tunnel: push generic protocol handling to ip_tunnel module")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_setup_cork() called inside ip_append_data() steals dst entry from rt to cork
and in case errors in __ip_append_data() nobody frees stolen dst entry
Fixes: 2e77d89b2f ("net: avoid a pair of dst_hold()/dst_release() in ip_append_data()")
Signed-off-by: Vasily Averin <vvs@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can retrieve opt from skb, no need to pass it as a parameter.
And opt should always be non-NULL, no need to check.
Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Tested-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cookie_v4_check() allocates ip_options_rcu in the same way
with tcp_v4_save_options(), we can just make it a helper function.
Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 971f10eca1 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
missed that cookie_v4_check() still calls ip_options_echo() which uses
IPCB(). It should use TCPCB() at TCP layer, so call __ip_options_echo()
instead.
Fixes: commit 971f10eca1 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Reported-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Tested-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
TCP Small queues tries to keep number of packets in qdisc
as small as possible, and depends on a tasklet to feed following
packets at TX completion time.
Choice of tasklet was driven by latencies requirements.
Then, TCP stack tries to avoid reorders, by locking flows with
outstanding packets in qdisc in a given TX queue.
What can happen is that many flows get attracted by a low performing
TX queue, and cpu servicing TX completion has to feed packets for all of
them, making this cpu 100% busy in softirq mode.
This became particularly visible with latest skb->xmit_more support
Strategy adopted in this patch is to detect when tcp_wfree() is called
from ksoftirqd and let the outstanding queue for this flow being drained
before feeding additional packets, so that skb->ooo_okay can be set
to allow select_queue() to select the optimal queue :
Incoming ACKS are normally handled by different cpus, so this patch
gives more chance for these cpus to take over the burden of feeding
qdisc with future packets.
Tested:
lpaa23:~# ./super_netperf 1400 --google-pacing-rate 3028000 -H lpaa24 -l 3600 &
lpaa23:~# sar -n DEV 1 10 | grep eth1
06:16:18 AM eth1 595448.00 1190564.00 38381.09 1760253.12 0.00 0.00 1.00
06:16:19 AM eth1 594858.00 1189686.00 38340.76 1758952.72 0.00 0.00 0.00
06:16:20 AM eth1 597017.00 1194019.00 38480.79 1765370.29 0.00 0.00 1.00
06:16:21 AM eth1 595450.00 1190936.00 38380.19 1760805.05 0.00 0.00 0.00
06:16:22 AM eth1 596385.00 1193096.00 38442.56 1763976.29 0.00 0.00 1.00
06:16:23 AM eth1 598155.00 1195978.00 38552.97 1768264.60 0.00 0.00 0.00
06:16:24 AM eth1 594405.00 1188643.00 38312.57 1757414.89 0.00 0.00 1.00
06:16:25 AM eth1 593366.00 1187154.00 38252.16 1755195.83 0.00 0.00 0.00
06:16:26 AM eth1 593188.00 1186118.00 38232.88 1753682.57 0.00 0.00 1.00
06:16:27 AM eth1 596301.00 1192241.00 38440.94 1762733.09 0.00 0.00 0.00
Average: eth1 595457.30 1190843.50 38381.69 1760664.84 0.00 0.00 0.50
lpaa23:~# ./tc -s -d qd sh dev eth1 | grep backlog
backlog 7606336b 2513p requeues 167982
backlog 224072b 74p requeues 566
backlog 581376b 192p requeues 5598
backlog 181680b 60p requeues 1070
backlog 5305056b 1753p requeues 110166 // Here, this TX queue is attracting flows
backlog 157456b 52p requeues 1758
backlog 672216b 222p requeues 3025
backlog 60560b 20p requeues 24541
backlog 448144b 148p requeues 21258
lpaa23:~# echo 1 >/proc/sys/net/ipv4/tcp_tsq_enable_tcp_wfree_ksoftirqd_detect
Immediate jump to full bandwidth, and traffic is properly
shard on all tx queues.
lpaa23:~# sar -n DEV 1 10 | grep eth1
06:16:46 AM eth1 1397632.00 2795397.00 90081.87 4133031.26 0.00 0.00 1.00
06:16:47 AM eth1 1396874.00 2793614.00 90032.99 4130385.46 0.00 0.00 0.00
06:16:48 AM eth1 1395842.00 2791600.00 89966.46 4127409.67 0.00 0.00 1.00
06:16:49 AM eth1 1395528.00 2791017.00 89946.17 4126551.24 0.00 0.00 0.00
06:16:50 AM eth1 1397891.00 2795716.00 90098.74 4133497.39 0.00 0.00 1.00
06:16:51 AM eth1 1394951.00 2789984.00 89908.96 4125022.51 0.00 0.00 0.00
06:16:52 AM eth1 1394608.00 2789190.00 89886.90 4123851.36 0.00 0.00 1.00
06:16:53 AM eth1 1395314.00 2790653.00 89934.33 4125983.09 0.00 0.00 0.00
06:16:54 AM eth1 1396115.00 2792276.00 89984.25 4128411.21 0.00 0.00 1.00
06:16:55 AM eth1 1396829.00 2793523.00 90030.19 4130250.28 0.00 0.00 0.00
Average: eth1 1396158.40 2792297.00 89987.09 4128439.35 0.00 0.00 0.50
lpaa23:~# tc -s -d qd sh dev eth1 | grep backlog
backlog 7900052b 2609p requeues 173287
backlog 878120b 290p requeues 589
backlog 1068884b 354p requeues 5621
backlog 996212b 329p requeues 1088
backlog 984100b 325p requeues 115316
backlog 956848b 316p requeues 1781
backlog 1080996b 357p requeues 3047
backlog 975016b 322p requeues 24571
backlog 990156b 327p requeues 21274
(All 8 TX queues get a fair share of the traffic)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_nh_match does not match nexthops correctly. Example:
ip route add 172.16.10/24 nexthop via 192.168.122.12 dev eth0 \
nexthop via 192.168.122.13 dev eth0
ip route del 172.16.10/24 nexthop via 192.168.122.14 dev eth0 \
nexthop via 192.168.122.15 dev eth0
Del command is successful and route is removed. After this patch
applied, the route is correctly matched and result is:
RTNETLINK answers: No such process
Please consider this for stable trees as well.
Fixes: 4e902c5741 ("[IPv4]: FIB configuration using struct fib_config")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We worked hard to improve tcp_ack() performance, by not accessing
skb_shinfo() in fast path (cd7d8498c9 tcp: change tcp_skb_pcount()
location)
We still have one spurious access because of ACK timestamping,
added in commit e1c8a607b2 ("net-timestamp: ACK timestamp for
bytestreams")
By checking if sk_tsflags has SOF_TIMESTAMPING_TX_ACK set,
we can avoid two cache line misses for the common case.
While we are at it, add two prefetchw() :
One in tcp_ack() to bring skb at the head of write queue.
One in tcp_clean_rtx_queue() loop to bring following skb,
as we will delete skb from the write queue and dirty skb->next->prev.
Add a couple of [un]likely() clauses.
After this patch, tcp_ack() is no longer the most consuming
function in tcp stack.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP Small Queues (tcp_tsq_handler()) can hold one reference on
sk->sk_wmem_alloc, preventing skb->ooo_okay being set.
We should relax test done to set skb->ooo_okay to take care
of this extra reference.
Minimal truesize of skb containing one byte of payload is
SKB_TRUESIZE(1)
Without this fix, we have more chance locking flows into the wrong
transmit queue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the missing validation code to avoid the use of nat/masq from
non-nat chains. The validation assumes two possible configuration
scenarios:
1) Use of nat from base chain that is not of nat type. Reject this
configuration from the nft_*_init() path of the expression.
2) Use of nat from non-base chain. In this case, we have to wait until
the non-base chain is referenced by at least one base chain via
jump/goto. This is resolved from the nft_*_validate() path which is
called from nf_tables_check_loops().
The user gets an -EOPNOTSUPP in both cases.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull percpu updates from Tejun Heo:
"A lot of activities on percpu front. Notable changes are...
- percpu allocator now can take @gfp. If @gfp doesn't contain
GFP_KERNEL, it tries to allocate from what's already available to
the allocator and a work item tries to keep the reserve around
certain level so that these atomic allocations usually succeed.
This will replace the ad-hoc percpu memory pool used by
blk-throttle and also be used by the planned blkcg support for
writeback IOs.
Please note that I noticed a bug in how @gfp is interpreted while
preparing this pull request and applied the fix 6ae833c7fe
("percpu: fix how @gfp is interpreted by the percpu allocator")
just now.
- percpu_ref now uses longs for percpu and global counters instead of
ints. It leads to more sparse packing of the percpu counters on
64bit machines but the overhead should be negligible and this
allows using percpu_ref for refcnting pages and in-memory objects
directly.
- The switching between percpu and single counter modes of a
percpu_ref is made independent of putting the base ref and a
percpu_ref can now optionally be initialized in single or killed
mode. This allows avoiding percpu shutdown latency for cases where
the refcounted objects may be synchronously created and destroyed
in rapid succession with only a fraction of them reaching fully
operational status (SCSI probing does this when combined with
blk-mq support). It's also planned to be used to implement forced
single mode to detect underflow more timely for debugging.
There's a separate branch percpu/for-3.18-consistent-ops which cleans
up the duplicate percpu accessors. That branch causes a number of
conflicts with s390 and other trees. I'll send a separate pull
request w/ resolutions once other branches are merged"
* 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (33 commits)
percpu: fix how @gfp is interpreted by the percpu allocator
blk-mq, percpu_ref: start q->mq_usage_counter in atomic mode
percpu_ref: make INIT_ATOMIC and switch_to_atomic() sticky
percpu_ref: add PERCPU_REF_INIT_* flags
percpu_ref: decouple switching to percpu mode and reinit
percpu_ref: decouple switching to atomic mode and killing
percpu_ref: add PCPU_REF_DEAD
percpu_ref: rename things to prepare for decoupling percpu/atomic mode switch
percpu_ref: replace pcpu_ prefix with percpu_
percpu_ref: minor code and comment updates
percpu_ref: relocate percpu_ref_reinit()
Revert "blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe"
Revert "percpu: free percpu allocation info for uniprocessor system"
percpu-refcount: make percpu_ref based on longs instead of ints
percpu-refcount: improve WARN messages
percpu: fix locking regression in the failure path of pcpu_alloc()
percpu-refcount: add @gfp to percpu_ref_init()
proportions: add @gfp to init functions
percpu_counter: add @gfp to percpu_counter_init()
percpu_counter: make percpu_counters_lock irq-safe
...
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
1/ Step down as dmaengine maintainer see commit 08223d80df "dmaengine
maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13 (commit
7787380336 "net_dma: mark broken"), without reports of performance
regression.
3/ Miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BBBv
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 7787380336 "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
