This code was passing the incorrect pointer to PTR_ERR_OR_ZERO() so it
always returned success. It should have been checking the array element
instead of the array itself.
Fixes: 96a2e242a5 ("leds: flash: Add driver to support flash LED module in QCOM PMICs")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ZoWJS_epjIMCYITg@stanley.mountain
Signed-off-by: Lee Jones <lee@kernel.org>
The SY7802 is a current-regulated charge pump which can regulate two
current levels for Flash and Torch modes.
It is a high-current synchronous boost converter with 2-channel high
side current sources. Each channel is able to deliver 900mA current.
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20240624-sy7802-v5-2-7abc9d96bfa6@apitzsch.eu
Signed-off-by: Lee Jones <lee@kernel.org>
The fwnode_for_each_child_node() loop requires manual intervention to
decrement the child refcount in case of an early return.
Add the missing calls to fwnode_handle_put(child) to avoid memory leaks
in the error paths.
Cc: stable@vger.kernel.org
Fixes: 679f865206 ("leds: Add mt6360 driver")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20240611-leds-mt6360-memleak-v1-1-93642eb5011e@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240522165358.62238-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
V4L2 will disable strobe mode of the LED device when enable torch mode,
but this logic will conflict with the "priv->fled_torch_used"
in "mt6360_strobe_set()". So after enabling torch mode of the first
LED, the second LED will not be able to enable torch mode correctly.
Therefore, at the beginning of "mt6360_strobe_set()", check whether the
state of the upcoming change and the current LED device state are the
same, so as to avoid the above problem.
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Link: https://lore.kernel.org/r/28FE6F1712799128000.chiaen_wu@richtek.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add a short struct description and remove one extraneous struct field
description to quieten these warnings:
leds-lm3601x.c:73: warning: missing initial short description on line:
* struct lm3601x_led -
leds-lm3601x.c💯 warning: Excess struct member 'led_name' description in 'lm3601x_led'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20240229071931.7870-2-rdunlap@infradead.org
Signed-off-by: Lee Jones <lee@kernel.org>
Enabling strobe and then setting brightness to 0 causes the driver to enter
invalid state after strobe end timer fires. We should cancel strobe mode
resources when changing brightness (aka torch mode).
Fixes: cef8ec8cbd ("leds: add sgm3140 driver")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217191133.1757553-1-megi@xff.cz
Signed-off-by: Lee Jones <lee@kernel.org>
Along the same lines as making devm_led_classdev_register() declared
extern unconditional, do the same thing for the two sub-classes
that have similar stubs.
The users of these interfaces go to great lengths to allow building
with both the generic leds API and the extended version, but realistically
there is not much use in this, so just simplify it to always rely
on it and remove the confusing fallback logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240109090715.982332-2-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The expresswire module requires gpiolib, so anything selecting it
also needs this dependency:
WARNING: unmet direct dependencies detected for LEDS_EXPRESSWIRE
Depends on [n]: NEW_LEDS [=y] && GPIOLIB [=n]
Selected by [y]:
- LEDS_KTD2692 [=y] && NEW_LEDS [=y] && LEDS_CLASS_FLASH [=y] && OF [=y]
Fixes: e59a15af7aa6 ("leds: ktd2692: Convert to use ExpressWire library")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240213165602.2230970-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The KTD2692 uses the ExpressWire protocol implemented in the newly
introduced ExpressWire library. Convert the driver to use the library.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-2-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-1-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct mt6370_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915201051.never.429-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct mt6360_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915201020.never.433-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
All platform drivers below drivers/leds/ unconditionally return zero in
their remove callback and so can be converted trivially to the variant
returning void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917130947.1122198-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
The variable 'count' is defined as unsigned type, so the following if
statement is invalid, we can modify the type of count to int.
if (count <= 0) {
dev_err(dev, "No led-sources specified\n");
return -ENODEV;
}
./drivers/leds/flash/leds-qcom-flash.c:546:5-10: WARNING: Unsigned expression compared with zero: count <= 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5344
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230531053559.5702-1-jiapeng.chong@linux.alibaba.com
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517180559.166329-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
The Qualcomm PMI8998 PMIC requires the LED to be disabled when configuring
the brightness. Always disable the LED when setting the brightness and
re-enable it afterwards.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-3-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
Add subtype for the Qualcomm PMI8998 PMIC to support it besides the
PM8150 PMIC which has the same registers. Adjust the driver to recognize
both PMIC subtypes as a 3 channel LED driver.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-2-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
Smatch reports:
drivers/leds/flash/leds-qcom-flash.c:103:18: warning:
symbol 'mvflash_3ch_regs' was not declared. Should it be static?
drivers/leds/flash/leds-qcom-flash.c:115:18: warning:
symbol 'mvflash_4ch_regs' was not declared. Should it be static?
These variables are only used locally, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230317191341.1670660-1-trix@redhat.com
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual Flash
LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the MT6370 Flash LED driver. Flash LED in MT6370
has 2 channels and support torch/strobe mode.
Co-developed-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/52480420a160e5a4c71715fbbf105e684a16e7c2.1678430444.git.chiaen_wu@richtek.com
Add initial driver to support flash LED module found in Qualcomm
Technologies, Inc. PMICs. The flash module can have 3 or 4 channels
and each channel can be controlled indepedently and support full scale
current up to 1.5 A. It also supports connecting two channels together
to supply one LED component with full scale current up to 2 A. In that
case, the current will be split on each channel symmetrically and the
channels will be enabled and disabled at the same time.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sm7225-fairphone-fp4 + pm6150l
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230303095023.538917-2-quic_fenglinw@quicinc.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-8-andriy.shevchenko@linux.intel.com
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The mutex might still be in use until the devm cleanup callback
devm_led_classdev_flash_release() is called. This only happens some time
after lm3601x_remove() completed.
Fixes: e63a744871 ("leds: lm3601x: Convert class registration to device managed")
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make the AUX pin optional, since it isn't a core part of functionality,
and the device is designed to be operational with only one CTRL pin.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use dev_err_probe instead of dev_err to avoid duplicate error
messages if the GPIO allocation makes the probe defer.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
output of dev_of_node() is already assigned to "np" variable in
ktd2692_parse_dt(). Use "np" variable to check if OF node is NULL
instead of calling dev_of_node() again.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add MT6360 LED driver include 2-channel Flash LED with torch/strobe mode,
3-channel RGB LED support Register/Flash/Breath Mode, and 1-channel for
moonlight LED.
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
fwnode_get_next_available_child_node() bumps a reference counting of
a returned variable. We have to balance it whenever we return to
the caller.
Fixes: e1c6edcbea ("leds: rt8515: Add Richtek RT8515 LED driver")
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add support for RT4505 flash LED controller. It can support up to 1.5A
flash current with hardware timeout and low input voltage protection.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The leds-rt8515 driver can optionall use the v4l2 flash led class,
but it causes a link error when that class is in a loadable module
and the rt8515 driver itself is built-in:
ld.lld: error: undefined symbol: v4l2_flash_init
>>> referenced by leds-rt8515.c
>>> leds/flash/leds-rt8515.o:(rt8515_probe) in archive
drivers/built-in.a
Adding 'depends on V4L2_FLASH_LED_CLASS' in Kconfig would avoid that,
but it would make it impossible to use the driver without the
v4l2 support.
Add the same dependency that the other users of this class have
instead, which just prevents the broken configuration.
Fixes: e1c6edcbea ("leds: rt8515: Add Richtek RT8515 LED driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This adds a driver for the Richtek RT8515 dual channel
torch/flash white LED driver.
This LED driver is found in some mobile phones from
Samsung such as the GT-S7710 and GT-I8190.
A V4L interface is added.
We do not have a proper datasheet for the RT8515 but
it turns out that RT9387A has a public datasheet and
is essentially the same chip. We designed the driver
in accordance with this datasheet. The day someone
needs to drive a RT9387A this driver can probably
easily be augmented to handle that chip too.
Sakari Ailus, Pavel Machek and Andy Shevchenko helped
significantly in getting this driver right.
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: newbytee@protonmail.com
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: linux-media@vger.kernel.org
Cc: phone-devel@vger.kernel.org
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
