The commit 111c182340 (kgdboc: reset
input devices (keyboards) when exiting debugger) introduced a
regression in early debugging such that you get a kernel oops on
continue (with the go command) if you boot a kernel with:
earlyprintk=vga ekgdboc=kbd kgdbwait
The restore kgdboc_restore_input() routine schedules work for the
purpose of sending key release events for any keys that were in the
depressed state prior to entering the kernel debugger. A simple fix
to the crash is to not invoke the schedule_work() if the kernel
system_state is anything other than SYSTEM_RUNNING.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
The saving of the NVS memory area during suspend and restoring it
during resume causes problems to appear on Sony Vaio VGN-NW130D, so
blacklist that machine to avoid those problems.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=23002
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Adriano <adriano.vilela@yahoo.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fault handling is getting enabled after enabling the interrupt-remapping (as
the success of interrupt-remapping can affect the apic mode and hence the
fault handling mode).
Hence there can potentially be some faults between the window of enabling
interrupt-remapping in the vt-d and the fault-handling of the vt-d units.
Handle any previous faults after enabling the vt-d fault handling.
For v2.6.38 cleanup, need to check if we can remove the dmar_fault() in the
enable_intr_remapping() and see if we can enable fault handling along with
enabling intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101201062244.630417138@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.
During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).
Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the system to hang.
Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: stable@kernel.org [v2.6.32+]
Reported-by: Max Asbock <masbock@linux.vnet.ibm.com>
Reported-and-tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fixed fsl dma slow issue by initializing dma mode register with
bandwidth control. It boosts dma performance and should works
with 85xx board.
Signed-off-by: Forrest Shi <b29237@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The code wants to check if there's a channel and it is not disabled,
but it used to check if channel is not NULL and accessed the channel
struct if this check failed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ltc4215 driver used the chip's "power good" status bit to provide
the power1_alarm file. This is wrong: the chip is really reporting the
status of one of the monitored voltages.
Change the sysfs file from power1_alarm to in2_min_alarm instead. This
matches the voltage that the chip is raising an alarm for.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
__pppoe_xmit function return value was invalid resulting in
additional call to kfree_skb on already freed skb. This resulted in
memory corruption and consequent kernel panic after PPPoE peer
terminated the link.
This fixes commit 55c95e738d.
Reported-by: Gorik Van Steenberge <gvs@zemos.net>
Reported-by: Daniel Kenzelmann <kernel.bugzilla@kenzelmann.dyndns.info>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Reported-by: Pawel Staszewski <pstaszewski@artcom.pl>
Diagnosed-by: Andrej Ota <andrej@ota.si>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Tested-by: Pawel Staszewski <pstaszewski@artcom.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Andrej Ota <andrej@ota.si>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must not wake the TX queue without free TX descriptors.
sca_xmit() expects at least one free descriptor and BUGs otherwise.
Problem reported and fix tested by Bernie Innocenti and Ward Vandewege.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing usage of rtnl_lock() to protect firmware interface registers.
These registers are accessed in some worker threads and can create a
deadlock if rtnl_lock is taken by upper layers while the worker is still
pending.
We remove rtnl_lock and use a driver mutex just while mailboxes are
accessed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Agere FW643 rev 06, listed as "11c1:5901 (rev 06) (prog-if 10 [OHCI])",
produced SBP-2 I/O errors since kernel 2.6.36. Disabling MSI fixes it.
Since MSI work on Agere FW643-E (same vendor and device ID, but rev 07),
introduce a device revision field into firewire-ohci's quirks list so
that different quirks can be defined for older and newer revisions.
Reported-by: Jonathan Isom <jeisom@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y
"VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403]"
does not generate any interrupts if Message Signaled Interrupts were
enabled. This is a regression since kernel 2.6.36 in which MSI support
was added to firewire-ohci. Hence blacklist MSI on all VIA controllers.
Reported-by: Robin Cook <rcook@wyrms.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y
Add the features struct and device table entry to enable yet another
version of Wacom Bamboo Pen (CTL460, Product ID 0xD4).
Signed-off-by: Kevin Granade <kevin.granade@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Properly const-, __init-, and __read_mostly-annotate this code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When CONFIG_CPU_FREQ=n ...
drivers/acpi/processor_thermal.c:159:12: warning: ‘acpi_thermal_cpufreq_increase’ defined but not used
drivers/acpi/processor_thermal.c:163:12: warning: ‘acpi_thermal_cpufreq_decrease’ defined but not used
Remove unused declaration of ‘acpi_thermal_cpufreq_increase’ and
‘acpi_thermal_cpufreq_decrease’
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
WARNING: drivers/acpi/acpi.o(.text+0xeda): Section mismatch in reference from the function acpi_os_initialize1() to the function .init.text:set_osi_linux()
The function acpi_os_initialize1() references
the function __init set_osi_linux().
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ERST writing may be used in NMI or Machine Check Exception handler. So
it need to use raw spinlock instead of normal spinlock. This patch
fixes it.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit b0ed7a91(ACPICA/ACPI: Add new host interfaces for _OSI suppor)
introduced another regression that only one _OSI string can be added or
removed.
Now multiple _OSI strings can be added or removed, for example
acpi_osi=Linux acpi_osi=FreeBSD acpi_osi="!Windows 2006"
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit b0ed7a91(ACPICA/ACPI: Add new host interfaces for _OSI suppor)
introduced a regression that _OSI string setup fails.
There are 2 paths to setup _OSI string.
DMI:
acpi_dmi_osi_linux -> set_osi_linux -> acpi_osi_setup -> copy _OSI
string to osi_setup_string
Boot command line:
acpi_osi_setup -> copy _OSI string to osi_setup_string
Later, acpi_osi_setup_late will be called to handle osi_setup_string.
If _OSI string is "Linux" or "!Linux", then the call path is,
acpi_osi_setup_late -> acpi_cmdline_osi_linux -> set_osi_linux ->
acpi_osi_setup -> copy _OSI string to osi_setup_string
This actually never installs _OSI string(acpi_install_interface not
called), but just copy the _OSI string to osi_setup_string.
This patch fixes the regression.
Reported-and-tested-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Was using L1_CACHE_BYTES for the Ingress Queue Entry Size but it really
needs to be 64 bytes in order to support the largest message sizes.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver.
I've had to add an additional delay (2ns) to adjust RX clock phase at
GMII/ RGMII interface (according to the PHY data-sheet). This helps to
have the RGMII working on some ST platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relationships
exposed by sysfs and udev. Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass reference to napi instead of enic device to the isr that services receive queue.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since connector can be built as a module and uses netlink socket
to communicate. The module should have an alias to autoload when socket
of NETLINK_CONNECTOR type is requested.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that one of the post-2.6.36 patches broke runtime PM of the
r8169 on my MSI Wind test machine in such a way that the link was not
brought up after reconnecting the network cable.
In the process of debugging the issue I realized that we only should
invoke the runtime PM functions in rtl8169_check_link_status() when
link change is reported and if we do so, the problem goes away.
Moreover, this allows rtl8169_runtime_idle() to be simplified quite
a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is definitly a problem, that some option cards send up broken
IP pakets leading to corrupted IP packets. These corruptions aren't
detected, because the driver claims that the packets are already
checksummed. This change removes the CHECKSUM_UNNECESSARY option
and let IP detect broken data.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A while back I made some changes to enable netpoll in the bonding driver. Among
them was a per-cpu flag that indicated we were in a path that held locks which
could cause the netpoll path to block in during tx, and as such the tx path
should queue the frame for later use. This appears to have given rise to a
regression. If one of those paths on which we hold the per-cpu flag yields the
cpu, its possible for us to come back on a different cpu, leading to us clearing
a different flag than we set. This results in odd netpoll drops, and BUG
backtraces appearing in the log, as we check to make sure that we only clear set
bits, and only set clear bits. I had though briefly about changing the
offending paths so that they wouldn't sleep, but looking at my origional work
more closely, it doesn't appear that a per-cpu flag is warranted. We alrady
gate the checking of this flag on IFF_IN_NETPOLL, so we don't hit this in the
normal tx case anyway. And practically speaking, the normal use case for
netpoll is to only have one client anyway, so we're not going to erroneously
queue netpoll frames when its actually safe to do so. As such, lets just
convert that per-cpu flag to an atomic counter. It fixes the rescheduling bugs,
is equivalent from a performance perspective and actually eliminates some code
in the process.
Tested by the reporter and myself, successfully
Reported-by: Liang Zheng <lzheng@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI_DEVICE_ID_CISSF is defined as 323b in pci_ids.h but redefined as 3fff in
hpsa.c. The ID of 3fff will _never_ ship as a standalone controller. It is
intended only as part a complete storage solution. As such, this patch
removes the redefinition and the StorageWorks P1210m from the product table.
It also removes a duplicate line for the "unknown" controller support.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Sometimes the Battery driver doesn't get notifications when it's
plugged/unplugged. And this results in the incorrect Battery
status reported by the power supply sysfs I/F.
Update Battery status first when querying from sysfs.
http://marc.info/?l=linux-acpi&m=128855015826728&w=2
Tested_by: Seblu <seblu@seblu.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
BIOSes. Can't live without them (apparently), definitely can't live with
them.
Reported-by: Ben Gamari <bgamari@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24312
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fix two bugs with the port array setup.
The first bug will only show up with broken xHCI hosts with Extended
Capabilities registers that have duplicate port speed entries for the same
port. The idea with the original code was to set the port_array entry to
-1 if the duplicate port speed entry said the port was a different speed
than the original port speed entry. That would mean that later, the port
would not be exposed to the USB core. Unfortunately, I forgot a continue
statement, and the port_array entry would just be overwritten in the next
line.
The second bug would happen if there are conflicting port speed registers
(so that some entry in port_array is -1), or one of the hardware port
registers was not described in the port speed registers (so that some
entry in port_array is 0). The code that sets up the usb2_ports array
would accidentally claim those ports. That wouldn't really cause any
user-visible issues, but it is a bug.
This patch should go into the stable trees that have the port array and
USB 3.0 port disabling prevention patches.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
A return value is not set for the successful case and it has a garbage value.
This fix will set the default value to SUCCESS and in case of any failures
it is changed.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This would cause a panic while reading the NPIV-config data.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_SHARED flag should not be set when calling request_irq for MSI
since this interrupt mechanism cannot be shared like standard INTx.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use the host_to_fcp_swap call to correctly populate the LUN field
in the Command Type 6 path. This field is used during LUN reset
cleanup and must match the field used in the FCP command.
Cc: stable@kernel.org
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
From: Johannes Berg <johannes.berg@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Interrupting the connection to the FCP channel while I/O requests are
being issued can lead to this deadlock. scsi_dispatch_cmd already
holds the host_lock while the recovery trigger tries to acquire the
host_lock again when iterating through the scsi_devices.
INFO: lockdep is turned off.
BUG: spinlock lockup on CPU#1, blast/9660, 0000000078f38878
CPU: 1 Not tainted 2.6.35.7SWEN2 #2
Process blast (pid: 9660, task: 0000000071f75940, ksp: 0000000074393ac0)
0000000074393640 00000000743935c0 0000000000000002 0000000000000000
0000000074393660 00000000743935d8 00000000743935d8 00000000005590c2
0000000000000000 0000000078f38878 0000000026ede800 0000000078f38878
000000000000000d 040000000000000c 0000000074393628 0000000000000000
0000000000000000 0000000000100b2a 00000000743935c0 0000000074393600
Call Trace:
([<0000000000100a32>] show_trace+0xee/0x144)
[<00000000003be202>] do_raw_spin_lock+0x112/0x178
[<000000000055d408>] _raw_spin_lock_irqsave+0x90/0xb0
[<00000000003f1514>] __scsi_iterate_devices+0x38/0xbc
[<00000000004849b0>] zfcp_erp_clear_adapter_status+0xd0/0x16c
[<000000000048587a>] zfcp_erp_adapter_reopen+0x3a/0xb4
[<0000000000489812>] zfcp_fsf_req_send+0x166/0x180
[<000000000048c8d6>] zfcp_fsf_fcp_cmnd+0x272/0x408
[<000000000048f864>] zfcp_scsi_queuecommand+0x11c/0x1e0
[<00000000003f1f2a>] scsi_dispatch_cmd+0x1d6/0x324
[<00000000003f9910>] scsi_request_fn+0x42c/0x56c
[<00000000003828ae>] __blk_run_queue+0x86/0x140
[<000000000037f742>] elv_insert+0x11a/0x208
[<000000000038104c>] blk_insert_cloned_request+0x84/0xe4
[<000003c0032b7c64>] dm_dispatch_request+0x6c/0x94 [dm_mod]
[<000003c0032b7d5c>] map_request+0xd0/0x100 [dm_mod]
[<000003c0032b9a78>] dm_request_fn+0xec/0x1bc [dm_mod]
[<0000000000382c0e>] generic_unplug_device+0x5a/0x6c
[<000003c0032b7f98>] dm_unplug_all+0x74/0x9c [dm_mod]
[<00000000001d1272>] sync_page+0x76/0x9c
[<00000000001d12ba>] sync_page_killable+0x22/0x60
[<000000000055a768>] __wait_on_bit_lock+0xc0/0x124
[<00000000001d1140>] __lock_page_killable+0x78/0x84
[<00000000001d351c>] generic_file_aio_read+0x5a4/0x7e8
[<0000000000228ec0>] do_sync_read+0xc8/0x12c
[<0000000000229edc>] vfs_read+0xac/0x1ac
[<000000000022a0d8>] SyS_read+0x58/0xa8
[<00000000001146de>] sysc_noemu+0x10/0x16
[<00000200000493c4>] 0x200000493c4
INFO: lockdep is turned off.
Call zfcp_fsf_fcp_cmnd without the host_lock and disable the
interrupts when acquiring the req_q_lock. According to the patch
description in "[PATCH] Eliminate error handler overload of the SCSI
serial number", the serial_number is not used, so simply drop the
queuecommand wrapper function and run zfcp_scsi_queuecommand without
holding the host_lock.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The ERP got values assigned for which no reference was taken. This
can lead to an unpredictable race condition. Fix this by only
assigning the values which are required and for which a reference was
pulled or is held implicitly.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the evaluation of GPN_FT requests wants to remove an invalid port
from the system the zfcp_erp_port_shutdown function is triggered.
Depending on the system status a superior action (e.g. adapter reopen)
is required. This can lead to an invalid mem access of the port struct
which might be freed at the time since the superior action is not
holding a reference of the port which triggered this ERP action.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The request data assignment between the fsf abort initiator and its
corresponding handler is not consistent and leads to an unpredictable
behaviour, e.g. kernel panic. This patch fixes this issue and assigns
the correct value.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The error handler is using the test cmd->serial_number == 0 in the
abort routines to signal that the command to be aborted has already
completed normally. This design was to close a race window in the
original error handler where a command could go through the normal
completion routines after it timed out but before error handling was
started.
Mike Anderson pointed out that when we converted our timeout and
softirq completions, we picked up atomicity here because the block
layer now mediates this with the REQ_ATOM_COMPLETE flag and guarantees
that *either* the command times out or our done routine is called, but
ensures we can't get both occurring. That makes the serial number
zero check redundant and it can be removed.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Firmware requires a larger configuration entry size than the driver
currently allows, and MSI-X pretty much doesn't work with current FW,
so disable it for now.
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bio_map_kern() returns ERR_PTRs on failure and never returns NULL.
[jejb: remove redundant unlikely spotted by Tobias Klauser]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the tail advances beyond the autoreport HEAD value, then we need to
fallback to an uncached read of the HEAD register in order to ascertain
the correct amount of remaining space in the ringbuffer.
Reported-by: Fang, Xun <xunx.fang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32259
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Correct the register table for SM2, LDO8, RTC
Change-Id: I45348cec5ffbb7da9bd7523764fb611b537236b8
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change-Id: I40400bb65eab496bb1becd26b37a9653b99d4f41
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(Split into separate patches)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change-Id: Idacf5e1e51dbbbcd5ea93f310a4e907977e7359e
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(Split into separate patches)
(Minor formatting fixes)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change-Id: I76eaceb31b56264f6978af15db1e6fc7e2e01b5a
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(Split into separate patches)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It should be required for all 7xx asics, but seems to cause
problems on some AGP 7xx chips.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=19002
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reported-and-Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The "e" pointer is either NULL or freed when we call
drm_vblank_put(dev, e->pipe) on the error path. Just pass the "pipe"
variable directly instead.
I changed another caller to use "pipe" as well for consistency.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Grub doesn't parse spaces in parameters correctly, so
this makes it impossible to force video= parameters
for kms on the grub kernel command line.
v2: shorten the names to make them easier to type.
Reported-by: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we fail to start a raid10 for some reason, we call
md_unregister_thread to kill the thread that was created.
Unfortunately md_thread() will then make one call into the handler
(raid10d) even though md_wakeup_thread has not been called. This is
not safe and as md_unregister_thread is called after mddev->private
has been set to NULL, it will definitely cause a NULL dereference.
So fix this at both ends:
- md_thread should only call the handler if THREAD_WAKEUP has been
set.
- raid10 should call md_unregister_thread before setting things
to NULL just like all the other raid modules do.
This is applicable to 2.6.35 and later.
Cc: stable@kernel.org
Reported-by: "Citizen" <citizen_lee@thecus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
With v0.90 metadata, a hot-spare does not become a full member of the
array until recovery is complete. So if we re-add such a device to
the array, we know that all of it is as up-to-date as the event count
would suggest, and so it a bitmap-based recovery is possible.
However with v1.x metadata, the hot-spare immediately becomes a full
member of the array, but it record how much of the device has been
recovered. If the array is stopped and re-assembled recovery starts
from this point.
When such a device is hot-added to an array we currently lose the 'how
much is recovered' information and incorrectly included it as a full
in-sync member (after bitmap-based fixup).
This is wrong and unsafe and could corrupt data.
So be more careful about setting saved_raid_disk - which is what
guides the re-adding of devices back into an array.
The new code matches the code in slot_store which does a similar
thing, which is encouraging.
This is suitable for any -stable kernel.
Reported-by: "Dailey, Nate" <Nate.Dailey@stratus.com>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
As recorded in
https://bugzilla.kernel.org/show_bug.cgi?id=24012
it is possible for a flush request through md to hang. This is due to
an interaction between the recursion avoidance in
generic_make_request, the insistence in md of only having one flush
active at a time, and the possibility of dm (or md) submitting two
flush requests to a device from the one generic_make_request.
If a generic_make_request call into dm causes two flush requests to be
queued (as happens if the dm table has two targets - they get one
each), these two will be queued inside generic_make_request.
Assume they are for the same md device.
The first is processed and causes 1 or more flush requests to be sent
to lower devices. These get queued within generic_make_request too.
Then the second flush to the md device gets handled and it blocks
waiting for the first flush to complete. But it won't complete until
the two lower-device requests complete, and they haven't even been
submitted yet as they are on the generic_make_request queue.
The deadlock can be broken by using a separate thread to submit the
requests to lower devices. md has such a thread readily available:
md_wq.
So use it to submit these requests.
Reported-by: Giacomo Catenazzi <cate@cateee.net>
Tested-by: Giacomo Catenazzi <cate@cateee.net>
Signed-off-by: NeilBrown <neilb@suse.de>
submit_flushes is called from exactly one place.
Move the code that is before and after that call into
submit_flushes.
This has not functional change, but will make the next patch
smaller and easier to follow.
Signed-off-by: NeilBrown <neilb@suse.de>
None of the functions called between setting flush_pending to 1, and
atomic_dec_and_test can change flush_pending, or will anything
running in any other thread (as ->flush_bio is not NULL). So the
atomic_dec_and_test will always succeed.
So remove the atomic_sec and the atomic_dec_and_test.
Signed-off-by: NeilBrown <neilb@suse.de>
In ib_uverbs_poll_cq() code there is a potential integer overflow if
userspace passes in a large cmd.ne. The calls to kmalloc() would
allocate smaller buffers than intended, leading to memory corruption.
There iss also an information leak if resp wasn't all used.
Unprivileged userspace may call this function, although only if an
RDMA device that uses this function is present.
Fix this by copying CQ entries one at a time, which avoids the
allocation entirely, and also by moving this copying into a function
that makes sure to initialize all memory copied to userspace.
Special thanks to Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
for his help and advice.
Cc: <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
[ Monkey around with things a bit to avoid bad code generation by gcc
when designated initializers are used. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... and interface up.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This results in an erroneus num_adhoc_vifs count, as the this counter
was incremented but not decremented for mesh interfaces.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler takes a lock - but since commit bcad6e80f3 this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.
Fix orinoco_cs and spectrum_cs
<https://bugzilla.kernel.org/show_bug.cgi?id=23932>
Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to set LRO on ehea, the user must set a module parameter, which
is not the standard way to do so. This patch adds a way to set LRO using
the ethtool tool.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regarding benet be_cmd_multicast_set() function, now using
netdev_for_each_mc_addr() helper for mac address copy, but
when copying to req->mac[] did not increase of the index.
Cc: Sathya Perla <sathyap@serverengines.com>
Cc: Subbu Seetharaman <subbus@serverengines.com>
Cc: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Cc: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DisplayPort standard (1.1a) states that:
The I2C-over-AUX Reply field is valid only when Native AUX CH Reply
field is AUX_ACK (00). When Native AUX CH Reply field is not 00, then,
I2C-over-AUX Reply field must be 00 and be ignored.
This fixes broken EDID reading when using an active DisplayPort to
duallink DVI converter. If the AUX CH replier chooses to defer the
transaction, a short read occurs and erroneous data is returned as
the i2c reply due to a lack of length checking and failure to check
for AUX ACK.
As a result, broken EDIDs can look like:
0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef
00: bc bc bc ff bc bc bc ff bc bc bc ac bc bc bc 45 ???.???.???????E
10: bc bc bc 10 bc bc bc 34 bc bc bc ee bc bc bc 4c ???????4???????L
20: bc bc bc 50 bc bc bc 00 bc bc bc 40 bc bc bc 00 ???P???.???@???.
30: bc bc bc 01 bc bc bc 01 bc bc bc a0 bc bc bc 40 ???????????????@
40: bc bc bc 00 bc bc bc 00 bc bc bc 00 bc bc bc 55 ???.???.???.???U
50: bc bc bc 35 bc bc bc 31 bc bc bc 20 bc bc bc fc ???5???1??? ????
60: bc bc bc 4c bc bc bc 34 bc bc bc 46 bc bc bc 00 ???L???4???F???.
70: bc bc bc 38 bc bc bc 11 bc bc bc 20 bc bc bc 20 ???8??????? ???
80: bc bc bc ff bc bc bc ff bc bc bc ff bc bc bc ff ???.???.???.???.
...
which can lead to:
[drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder
[drm:drm_edid_block_valid] *ERROR* Raw EDID:
<3>30 30 30 30 30 30 30 32 38 32 30 32 63 63 31 61 000000028202cc1a
<3>28 00 02 8c 00 00 00 00 18 00 00 00 00 00 00 00 (...............
<3>20 4c 61 73 74 20 62 65 61 63 6f 6e 3a 20 33 32 Last beacon: 32
<3>32 30 6d 73 20 61 67 6f 46 00 05 8c 00 00 00 00 20ms agoF.......
<3>36 00 00 00 00 00 00 00 00 0c 57 69 2d 46 69 20 6.........Wi-Fi
<3>52 6f 75 74 65 72 01 08 82 84 8b 96 24 30 48 6c Router......$0Hl
<3>03 01 01 06 02 00 00 2a 01 00 2f 01 00 32 04 0c .......*../..2..
<3>12 18 60 dd 09 00 10 18 02 00 00 01 00 00 18 00 ..`.............
Signed-off-by: David Flynn <davidf@rd.bbc.co.uk>
[ickle: fix up some surrounding checkpatch warnings]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
When matching error address to the range contained by one memory node,
we're in valid range when node interleaving
1. is disabled, or
2. enabled and when the address bits we interleave on match the
interleave selector on this node (see the "Node Interleaving" section in
the BKDG for an enlightening example).
Thus, when we early-exit, we need to reverse the compound logic
statement properly.
Cc: <stable@kernel.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This corrects the misprint introduced when moving '#if
PAGE_SHIFT' from i7core_edac.c to edac_core.h (commit
e9144601d3)
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrei Konovalov <akonovalov@mvista.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
00740c5854 changed edac_core to
un-/register a workqueue item only if a lowlevel driver supplies a
polling routine. Normally, when we remove a polling low-level driver, we
go and cancel all the queued work. However, the workqueue unreg happens
based on the ->op_state setting, and edac_mc_del_mc() sets this to
OP_OFFLINE _before_ we cancel the work item, leading to NULL ptr oops on
the workqueue list.
Fix it by putting the unreg stuff in proper order.
Cc: <stable@kernel.org> #36.x
Reported-and-tested-by: Tobias Karnat <tobias.karnat@googlemail.com>
LKML-Reference: <1291201307.3029.21.camel@Tobias-Karnat>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
If we break the loop when there are still skbs in tq and no skb in
rq, the skbs will be left in txq until new skbs are enqueued into rq.
In rare cases, no new skb is queued, then these skbs will stay in rq
forever.
After this patch, if tq isn't empty when we break the loop, we goto
resched directly.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of the inexact hash-based MAC address filter.
It's 64 bits but current code is missing a ULL. Results in filtering out
some legitimate packets.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow 1 as a valid div value as specified in the ADM1026 datasheet.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent setting fan_div from stomping on other fans that share the
same I2C register.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The manual fan speed control logic of the IT8721F is much different
from what older devices had. Update the code to properly support that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
If we fail to find a hci device pointer in hci_uart, don't try
to deref the NULL one we do have.
Signed-off-by: Jun Nie <njun@marvell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: i915 cannot provide switcher services.
drm/radeon/kms: fix vram base calculation on rs780/rs880
drm/radeon/kms: fix formatting of vram and gtt info
drm/radeon/kms: forbid big bo allocation (fdo 31708) v3
drm: Don't try and disable an encoder that was never enabled
drm: Add missing drm_vblank_put() along queue vblank error path
drm/i915/dp: Only apply the workaround if the select is still active
drm/i915: Emit a request to clear a flushed and idle ring for unbusy bo
drm/i915/lvds: Always restore panel-fitter when enabling the LVDS
drm/i915/ringbuffer: Only print an error on the second attempt to reset head
drm/i915: announce to userspace that the bsd ring is coherent
agp/intel: Fix wrong kunmap in i830_cleanup()
drm/i915: Factor in pixel-repeat in FDI M/N calculation
drm/i915: Death to the unnecessary 64bit divide
drm/i915: Clean conflicting modesetting registers upon init
drm/i915: Apply a workaround for transitioning from DP on pipe B to HDMI.
drm/i915: Always set the DP transcoder config to 8BPC.
Adds new Bamboo Pen & Touch model - Bamboo P & T Special Edition
Medium (CTH661/L; Product ID = 0xdb).
Tested-by: Tobias Verbeke <tobias.verbeke@gmail.com>
Signed-off-by: David Foley <favux.is@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The firmware framework gets initialized during fs_initcall time, so
we are not allowed to call request_firmware earlier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid overflowing a 32 bit value.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Forbid allocating buffer bigger than visible VRAM or GTT, also
properly set lpfn field.
v2 - use max macro
- silence warning
v3 - don't explicitly set range limit
- use min macro
Cc: stable <stable@kernel.org>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prevents code that assumes that the encoder is active when asked to be
disabled from dying a horrible death.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently, in case of using scatter/gather mode, head of data is not sent to
destination. The cause is second descriptor address is set to NEXT.
The NEXT must have head of descriptor address.
This patch sets head of descriptor address to the NEXT.
Acked-by: Yong Wang <youg.y.wang@intel.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
[dan.j.williams@intel.com: fixed up usage of virt_to_phys()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.
Fixes regression in 5bddd17.
Reported-and-tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17]
Call netif_napi_{add,del}() on the NAPI contexts in the new and
old channels, respectively.
Since efx_init_napi() cannot fail, make its return type void.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.
This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Cc: stable@kernel.org
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are using a legacy interrupt, our IRQ may be shared and our
interrupt handler may be called even though interrupts are disabled on
the NIC. When we change ring sizes, we reallocate the event queue and
the interrupt handler may use an invalid pointer when called for
another device's interrupt.
Maintain a legacy_irq_enabled flag and test that at the top of the
interrupt handler. Note that this problem results from the need to
work around broken INT_ISR0 reads, and does not affect the legacy
interrupt handler for Falcon A1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
wmi: use memcmp instead of strncmp to compare GUIDs
ACPI, hp-wmi: Fix memory leak in acpi query
msi-wmi: fix semantically incorrect use of keycode instead of scancode
msi-wmi: Add mute key support
asus-laptop: add wimax and wwan support
eeepc-wmi: fix compiler warning
ibm_rtl: _RTL_ is not available in UEFI mode
ibm_rtl: Loosen the DMI criteria to all IBM machines
drivers/platform/x86/thinkpad_acpi.c: delete double assignment
eeepc-wmi: add cpufv sysfs documentation
toshiba_acpi.c: Add key_entry for a lone FN keypress
ibm_rtl: fix printk format warning
In order for bos to retire eventually, a request must be sent down the
ring. This is expected, for example, by occlusion queries for which mesa
will wait upon (whilst running glean) before issuing more batches and so
the normal activity upon the ring is suspended and we need to emit a
request to clear the idle ring.
Reported-by: Jinjin, Wang <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The existing gpio-keys driver can be usable only for GPIO lines with
interrupt support. Several devices have buttons connected to a GPIO
line which is not capable to generate interrupts. This patch adds a
new input driver using the generic GPIO layer and the input-polldev
to support such buttons.
[Ben Gardiner <bengardiner@nanometrics.ca: fold code to use more
of the original gpio_keys infrastructure; cleanups and other
improvements.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 2c01946c6b (omap3 nand: cleanup
virtual address usages) wrongly enabled CONFIG_MTD_NAND_OMAP_HWECC
which breaks boards like beagle and pandora that use software ECC
for write.
Boards like beagle and pandora uses sw ecc for write (e.g. binary flushed
from u-boot) and read from kernel.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6524/1: GIC irq desciptor bug fix
ARM: 6523/1: iop: ensure sched_clock() is notrace
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
ARM: cns3xxx: Fix build with CONFIG_PCI=y
While looking for the duplicates in /sys/class/wmi/, I couldn't find
them. The code that looks for duplicates uses strncmp in a binary GUID,
which may contain zero bytes. The right function is memcmp, which is
also used in another section of wmi code.
It was finding 49142400-C6A3-40FA-BADB-8A2652834100 as a duplicate of
39142400-C6A3-40FA-BADB-8A2652834100. Since the first byte is the fourth
printed, they were found as equal by strncmp.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org
After freeing the rings we were not zeroing out the ring count values.
This patch now clears these counts correctly.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Really fix build break on symbol-prefixed archs
[media] Fix Kconfig errors due to two visible menus
i2c/algos: convert Kconfig to use the menu's `visible' keyword
media/video: convert Kconfig to use the menu's `visible' keyword
Revert "i2c: Fix Kconfig dependencies"
kconfig: regen parser
kconfig: add an option to determine a menu's visibility
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: Fix GSC PS/2 driver name for keyboard and mouse
parisc: KittyHawk LCD fix
parisc: convert the rest of the irq handlers to simple/percpu
parisc: fix dino/gsc interrupts
parisc: remove redundant initialization in sigsegv path of sys_rt_sigreturn
Linus Torvalds pointed out that our code was unbalanced when powering on
the panel with respect to the power off sequence in that we were failing
to restore the panel-fitter. The consequence of this would be that
across a simple DPMS off/on for a non-native mode, without an intervening
modeset, the panel fitter would remain disabled and the output would shift
on the panel.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There's not much we can do here but hope for the best. However the first
failure happens quite frequently and if often remedied by the second
attempt to reset HEAD. So only print the error if that attempt also
fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=19802
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).
[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a missing NULL check and fix the wrong address passed to kunmap()
in i830_cleanup().
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[danvet: added cc stable]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rename intel_mid_dma_pci to intel_mid_dma_pci_driver to pick up the
applied annotations of that suffix.
Reported-by: <major_Lee@wistron.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently while submitting scatterlists with more than one SG
entry the DMA buffer address from the first SG entry is inserted
into all initialized DMA buffer descriptors. This is due to the
typo in the for_each_sg() loop where the scatterlist pointer is
used for obtaining the DMA buffer address and _not_ the SG list
iterator.
As a result all received data will be written only into the first
DMA buffer while reading. While writing the data from the first
DMA buffer is send to the device multiple times. This caused
the filesystem destruction on the MMC card when using DMA in
mxcmmc driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Changed Makefile to use <modules>-y instead of <modules>-objs. Following
(documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
K class aka KittyHawk don't have LED support on their LCD. Installing
HP-UX confirmed this. The current led_wq fills the LCD with black
characters each time it runs.
The patch prevents the led_wq workqueue and its proc entry to be
created for KittyHawk machines.
It also increase min_cmd_delay as currently, one character out of two
is lost when a string is sent to the LCD.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Kyle McMartin <kyle@mcmartin.c>
The generic conversion eliminates the spurious no_ack and no_end
routines, converts all the cascaded handlers to handle_simple_irq() and
makes iosapic use a modified handle_percpu_irq() to become the same as
the CPU irq's. This isn't an essential change, but it eliminates the
mask/unmask overhead of handle_level_irq().
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fixes the modesetting on the secondary panel of the Libretto W100 and
presumably many more Ironlake laptops with SDVO LVDS displays.
Reported-and-tested-by: Matthew Willoughby <mattfredwill@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
ARM: pcmcia: Fix for building DEBUG with sa11xx_base.c as a module.
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
Cc: <stable@kernel.org>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the hardware DDA to calculate the ratio with as much accuracy as is
possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
* '2.6.37-rc4-pvhvm-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: unplug the emulated devices at resume time
xen: fix save/restore for PV on HVM guests with pirq remapping
xen: resume the pv console for hvm guests too
xen: fix MSI setup and teardown for PV on HVM guests
xen: use PHYSDEVOP_get_free_pirq to implement find_unbound_pirq
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: allocate irq descs on any NUMA node
xen: prevent crashes with non-HIGHMEM 32-bit kernels with largeish memory
xen: use default_idle
xen: clean up "extra" memory handling some more
* 'upstream/bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: x86/32: perform initial startup on initial_page_table
xen: don't bother to stop other cpus on shutdown/reboot
If we leave the registers in a conflicting state then when we attempt
to teardown the active mode, we will not disable the pipes and planes
in the correct order -- leaving a plane reading from a disabled pipe and
possibly leading to undefined behaviour.
Reported-and-tested-by: Andy Whitcroft <apw@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32078
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: se/7724: Remove FSI/B of GPIO init code
sh: se/7724: Update clock framework of FSI clock to non-legacy
sh: Assume new page cache pages have dirty dcache lines.
sh: boards: mach-se: use IS_ERR() instead of NULL check
sh: Add div6_reparent_clks to clock framework for FSI
dma: shdma: add a MODULE_ALIAS() to allow module autoloading
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
lxfb: Maintain video processor palette through suspend/resume
video: da8xx: Register IRQ as last thing in driver probing.
framebuffer: fix fbcmap.c kernel-doc warning
My new shiny code for corrupted PEB detection has NOR specific bug.
We tread PEB as corrupted and preserve it, if
1. EC header is OK.
2. VID header is corrupted.
3. data area is not "all 0xFFs"
In case of NOR we have 'nor_erase_prepare()' quirk, which invalidates
the headers before erasing the PEB. And we invalidate first the VID
header, and then the EC header. So if a power cut happens after we have
invalidated the VID header, but before we have invalidated the EC
header, we end up with a PEB which satisfies the above 3 conditions,
and the scanning code will treat it as corrupted, and will print
scary warnings, wrongly.
This patch fixes the issue by firt invalidating the EC header, then
invalidating the VID header. In case of power cut inbetween, we still
just lose the EC header, and UBI can deal with this situation gracefully.
Thanks to Anatolij Gustschin <agust@denx.de> for tracking this down.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reported-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Use the ccflag-y flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched. According to (documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We should not call kfree(dma) in mid_setup_dma error path because
the memory is allocated in intel_mid_dma_probe and will be freed
in intel_mid_dma_probe error path if mid_setup_dma return error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
otherwise, i will be -1 inside the latest iteration of the while loop.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: length resolution should be reported units/mm
HID: add support for F430 Force Feedback Wheel
HID: egalax: Use kzalloc
HID: Remove KERN_DEBUG from dbg_hid use
Manually fixed trivial conflict in drivers/hid/hid-input.c (due to
removal of KERN_DEBUG from dbg_hid use clashing with new keycode
interface switch)
Allocate irq descs on any NUMA node (we don't care) rather than
specifically node 0, which may not exist.
(At the moment NUMA is meaningless within a domain, so any info
the kernel has is just from an SRAT table we haven't suppressed/disabled.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If this is a non-HIGHMEM 32-bit kernel, then the page structures only go
up to the limit of addressable memory, even if more memory is physically
present. Don't try to add that extra memory to the balloon.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The AMD Geode CS5536 Companion Device Silicon Revision B1 Specification
Update mentions the follow as issue #36:
"Atomic write transactions to the atomic GPIO High Bank Feature Bit
registers should only affect the bits selected [...]"
"after Suspend, an atomic write transaction [...] will clear all
non-selected bits of the accessed register."
In other words, writing to the high bank for a single GPIO bit will
clear every other GPIO bit (but only sometimes after a suspend).
The workaround described is obvious and simple; do a read-modify-write.
This patch does that, and documents why we're doing it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's not useful to build LED triggers when there's no LEDs that can be
triggered by them. Therefore, fix up the dependencies so that this
cannot happen, and fix a few users that select triggers to depend on
LEDS_CLASS as well (there is also one user that also selects LEDS_CLASS,
which is OK).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Arnd Hannemann <arnd@arndnet.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This workaround only applies to Ironlake.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The pipe is always set to 8BPC, but here we were leaving whatever
previous bits were set by the BIOS in place.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This patch fixes hang in dmfe driver on attempt of sending a big packet.
Without this patch the code stops the queue and never wakes it again.
Signed-off-by: Alexander V. Lukyanov <lav@netis.ru>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reproduce: if connman (http://connman.net/) is started,
inserting the stmmac module triggers a "BUG: spinlock bad magic on CPU#0".
Registering the device in stmmac_probe() sends a notification to connman
which brings the interface up before the lock is initialized.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (27 commits)
Staging: rt2870: Add USB ID for Buffalo Airstation WLI-UC-GN
staging: easycap needs smp_lock.h, fixes build error
Staging: batman-adv: ensure that eth_type_trans gets linear memory
Staging: batman-adv: Don't remove interface with spinlock held
staging: brcm80211: updated maintainers contact information
staging: fix winbond build, needs delay.h
Staging: line6: fix up my fixup for some sysfs attribute permissions
Staging: zram: fix up my fixup for some sysfs attribute permissions
Staging: udlfb: fix up my fixup for some sysfs attribute permissions
Staging: samsung-laptop: fix up my fixup for some sysfs attribute permissions
Staging: iio: adis16220: fix up my fixup for some sysfs attribute permissions
Staging: frontier: fix up my fixup for some sysfs attribute permissions
Staging: asus_oled: fix up my fixup for some sysfs attribute permissions
staging: spectra: fix build error
Staging: intel_sst: fix memory leak
Staging: rtl8712: signedness bug in init
staging: rtl8187se: Change panic to warn when RF switch turned off
staging: comedi: fix memory leak
Staging: quickstart: free after input_unregister_device()
Staging: speakup: free after input_unregister_device()
...
* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
uio: Change mail address of Hans J. Koch
driver core: prune docs about device_interface
driver core: the development tree has switched to git
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: mfd: adjust the baud rate setting
TTY: open/hangup race fixup
TTY: don't allow reopen when ldisc is changing
NET: wan/x25, fix ldisc->open retval
TTY: ldisc, fix open flag handling
serial8250: Mark console as CON_ANYTIME
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix autosuspend bug in usb-serial
USB: ehci: disable LPM and PPCD for nVidia MCP89 chips
USB: serial: ftdi_sio: Vardaan USB RS422/485 converter PID added
USB: yurex: add .llseek fop to file_operations
USB: ftdi_sio: Add ID for RT Systems USB-29B radio cable
usb: musb: do not use dma for control transfers
usb: musb: gadget: fix compilation warning
usb: musb: clear RXCSR_AUTOCLEAR before PIO read
usb: musb: unmap dma buffer when switching to PIO
xhci: Don't let the USB core disable SuperSpeed ports.
xhci: Setup array of USB 2.0 and USB 3.0 ports.
xhci: Fix reset-device and configure-endpoint commands
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Fix information leak in marshalling code
IB/pack: Remove some unused code added by the IBoE patches
IB/mlx4: Fix IBoE link state
IB/mlx4: Fix IBoE reported link rate
mlx4_core: Workaround firmware bug in query dev cap
IB/mlx4: Fix memory ordering of VLAN insertion control bits
MAINTAINERS: Update NetEffect entry
This reverts commit 916448e77f.
"As far as I can tell, either of these patches breaks multiple VIF
scenarios. I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
-- Ben Greear <greearb@candelatech.com>
http://marc.info/?l=linux-wireless&m=129123368719339&w=2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: fix kernel-doc for set_consumer_device_supply
regulator: enable supply regulator only when use count is zero
regulator: twl-regulator - fix twlreg_set_mode
regulator: lock supply in regulator enable
regulator: Return proper error for regulator_register()
regulator: Ensure enough delay time for enabling regulator
regulator: Remove a redundant device_remove_file call in create_regulator
regulator: Staticise mc13783_powermisc_rmw()
regulator: regulator disable supply fix
When remapping MSIs into pirqs for PV on HVM guests, qemu is responsible
for doing the actual mapping and unmapping.
We only give qemu the desired pirq number when we ask to do the mapping
the first time, after that we should be reading back the pirq number
from qemu every time we want to re-enable the MSI.
This fixes a bug in xen_hvm_setup_msi_irqs that manifests itself when
trying to enable the same MSI for the second time: the old MSI to pirq
mapping is still valid at this point but xen_hvm_setup_msi_irqs would
try to assign a new pirq anyway.
A simple way to reproduce this bug is to assign an MSI capable network
card to a PV on HVM guest, if the user brings down the corresponding
ethernet interface and up again, Linux would fail to enable MSIs on the
device.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Use the new hypercall PHYSDEVOP_get_free_pirq to ask Xen to allocate a
pirq. Remove the unsupported PHYSDEVOP_get_nr_pirqs hypercall to get the
amount of pirq available.
This fixes find_unbound_pirq that otherwise would return a number
starting from nr_irqs that might very well be out of range in Xen.
The symptom of this bug is that when you passthrough an MSI capable pci
device to a PV on HVM guest, Linux would fail to enable MSIs on the
device.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
On some motherboards the it8712f watchdog does not work unless
the game port was enabled. see Bug 13140. We therefor add a note
to Kconfig.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* fix devinit and devexit sections
* fix platform removal code so that the iounmap happens after the removal of the timer.
* changes the reboot_notifier by a platform shutdown method.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds an additional LPC Controller DeviceID for the Intel Patsburg PCH for TCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Input ABI requires reporting resolution on main axes in units per
millimeter, not units per inch, so we need to convert accordingly.
Tested-by: Nikolai Kondrashov <spbnick@gmail.com>
Acked-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We erroneously ignored the Always Running APIC Timer on WSM-EX.
Move the check for ARAT down so that it can apply to any/all models.
Signed-off-by: Len Brown <len.brown@intel.com>
Drivers should append their name on exported symbols, to avoid
conflicts with allyesconfig:
drivers/staging/built-in.o: In function `format_by_fourcc':
/home/v4l/work_trees/linus/drivers/staging/cx25821/cx25821-video.c:96: multiple definition of `format_by_fourcc'
drivers/media/built-in.o:/home/v4l/work_trees/linus/drivers/media/common/saa7146_video.c:88: first defined here
Let's rename both occurences with a small shellscript:
for i in drivers/staging/cx25821/*.[ch]; do sed s,format_by_fourcc,cx25821_format_by_fourcc,g <$i >a && mv a $i; done
for i in drivers/media/common/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
for i in include/media/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ib_ucm_init_qp_attr() and ucma_init_qp_attr() pass struct ib_uverbs_qp_attr
with reserved, qp_state, {ah_attr,alt_ah_attr}{reserved,->grh.reserved}
fields uninitialized to copy_to_user(). This leads to leaking of
contents of kernel stack memory to userspace.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use netif_running() and netif_carrier_ok() to report link state,
exactly as is done to report Ethernet link state in sysfs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX firmware is supposed to report the number blue flame
registers per page as log2 of the value. However, due to a firmware
bug, it reports actual number. This patch works around this by
checking if the number of registers calculated fits within a page. If
it does not, we use 8 registers per page.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new interface creates directories per mapped image
and under each it creates a subdir per available snapshot.
This allows keeping a cleaner interface within the sysfs
guidelines. The ABI documentation was updated too.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
The uvcvideo driver now locks all ioctls correctly on its own, the BKL
isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The stream mutex protects access to the struct uvc_streaming ctrl,
cur_format and cur_frame fields as well as to the hardware probe
control. Lock it appropriately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mmap() implementation belongs to the video buffers queue, move it
there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callers outside uvc_queue.c should not be forced to lock/unlock the
queue mutex manually. Move the mutex operations inside
uvc_free_buffers().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
uvc_find_control() must be called with the controls mutex locked. Fix
uvc_query_v4l2_menu() accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The unregister function had a race condition with the v4l2_open
function. Ensure that both functions test and clear the REGISTER
flag from within a critical section.
Thanks to Laurent Pinchart for finding this race.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL replacement mutex had some serious performance side-effects on
V4L drivers. It is replaced by a better heuristic that works around the
worst of the side-effects.
Read the v4l2-dev.c comments for the whole sorry story. This is a
temporary measure only until we can convert all v4l drivers to use
unlocked_ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Where reasonable use mutex_lock_interruptible instead of mutex_lock.
Also fix the poll, read and write error codes when called with an unregistered
device (e.g. after a USB device was disconnected). Poll must return
POLLERR|POLLHUP and read/write must return -ENODEV.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also added locking around snd_cx18_pcm_ioctl as a precaution
as requested by Andy Walls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial conversion, this driver used a mutex already.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These drivers could be trivially converted to unlocked_ioctl since they
already did locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the typhoon driver from ioctl to unlocked_ioctl.
When doing this I noticed a bug where curfreq was not initialized correctly
to mutefreq (it wasn't multiplied by 16).
The initialization is now also done before the device node is created.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert ioctl to unlocked_ioctl. Note that for this driver the locking
is done inside the sub-device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert from ioctl to unlocked_ioctl using the v4l2 core lock.
Also removed the 'exclusive access' limitation. There was no need for it
and it violates the v4l2 spec as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted from ioctl to unlocked_ioctl.
This driver already used an internal lock, but it was missing in cadet_open and
cadet_release and it was not used correctly in cadet_read.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch converts a bunch of V4L2 radio drivers to unlocked_ioctl.
These are all simple conversions: most already had a lock and so the ioctl
fop could simply be replaced by unlocked_ioctl.
radio-miropcm20.c was converted to use the new V4L2 core lock.
While doing this work I noticed that many of these drivers initialized
some more fields or muted audio or something like that *after* creating
the device node. This should be done before the device node is created
to prevent problems. Especially hal tends to grab a device node as soon
as it is created.
In one or two cases the mutex_init was even done after the device creation!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If turning on a power resource fails, do not reference count it,
since it cannot be in use in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 3e384ee6c6 (ACPI / PM: Fix
reference counting of power resources) introduced a regression by
causing fan power resources to be turned on and reference counted
unnecessarily during resume, so on some boxes fans are always on
after resume.
Fix the problem by checking if the current device state is different
from the new state before reference counting and turning on power
resources in acpi_power_transition().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=22932 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Restore the check for an unassigned mac address before adopting the
first slaves as it's own. The change in behavior was introduced by:
commit c20811a79e
Author: Jiri Pirko <jpirko@redhat.com>
bonding: move dev_addr cpy to bond_enslave
Signed-off-by: David Strand <dpstrand@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for the b44_wap54g10_workaround was never included, because
the config option was wrong. The nvram_get function was never in
mainline kernel, only in external OpenWrt patches.
The code should be compiled in when CONFIG_BCM47XX is selected and not
when CONFIG_SSB_DRIVER_MIPS is selected, because nvram_getenv is only
available on bcm47xx platforms and now in the mainline kernel code.
Using an include is better than a second function declaration, to fix
this when the function signature changes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Move VLAN control bit setting to before wmb(). - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Atheros 3011 has small sflash firmware and needs to be
blacklisted in transport driver to load actual firmware
in DFU driver.
Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If a device is autosuspended an inability to resubmit URBs is
to be expected. Check the error code and only log real errors.
(Now that autosuspend is default enabled for btusb, those log
messages were happening all the time e.g. with a BT mouse)
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The ref-count of parport gained from parport_find_number()
was not released in normal path.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Geode X driver uses both of the LX's palettes, one for gamma
correction and one for colormaps.
The kernel driver currently only backs up the one used for colormaps
during suspend/resume. If you mess with gamma settings and do a
suspend/resume, colors go funny.
Fix this by backing up the video proc palette during suspend/resume,
alongside the display controller one which is already handled.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Following commit exposed a bug in driver:
"fbdev: da8xx/omap-l1xx: implement double buffering"
Bug is, if interrupt handler is called before initialization is
finished, raster controller is enabled and following register
modifications causes hardware to stay in a broken state.
By looking at this one may say that proper locking is missing in
this driver, and a more proper fix should be prepared. However,
aformentioned commit causes a regression in the driver and some
fix to current one should be applied first.
Signed-off-by: Caglar Akyuz <caglar@bilkon-kontrol.com.tr>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use correct bit positions of rsid field.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lenovo S10-3t's ClickPad is a 2-button ClickPad that reports BTN_LEFT
and BTN_RIGHT as normal touchpad, unlike the 1-button ClickPad used in
HP mini 210 that reports solely BTN_MIDDLE.
In 0xc0-cap response, the 1-button ClickPad has the 20-bit set while
2-button ClickPad has the 8-bit set.
This patch makes the kernel only handle 1-button ClickPad specially,
and treat 2-button ClickPad in the same fashion as regular touchpads.
This fixes kernel bug #18122 and MeeGo bug #4807.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add two new Bamboo Pen & Touch models:
Bamboo Comic Medium (CTH661/S1; Product ID = 0xd8)
Bamboo P & T Special Edition Small (CTH461/L; Product ID = 0xdA)
Tested-by: IRIE Shinsuke <irieshinsuke@yahoo.co.jp>
Tested-by: Andrea Cadeddu <mrernia@gmail.com>
Signed-off-by: David Foley <favux.is@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add workaround for dce3 ddc line vbios bug
drm/radeon/kms: fix interlaced and doublescan handling
drm/radeon/kms: fix typos in disabled vbios code
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm: record monitor status in output_poll_execute
drm: Set connector DPMS status to ON in drm_crtc_helper_set_config
drm/i915: fix regression due to ba3d8d749b
Revert "drm/radeon/kms: fix typo in r600 cs checker"
drm/i915/sdvo: Always add a 30ms delay to make SDVO TV detection reliable
MAINTAINERS: INTEL DRM DRIVERS list (intel-gfx) is subscribers-only
drm/i915/sdvo: Always fallback to querying the shared DDC line
drm/i915: Handle pagefaults in execbuffer user relocations
drm/i915/sdvo: Only enable HDMI encodings only if the commandset is supported
drm/radeon/kms: fix resume regression for some r5xx laptops
drm/radeon/kms: fix regression in rs4xx i2c setup
drm/i915: Only save/restore cursor regs if !KMS
drm/i915: Prevent integer overflow when validating the execbuffer
6xx/7xx was hitting the wrong BUS_CNTL reg and bits.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm/i915: fix regression due to ba3d8d749b
Previous baud rate setting code only has been tested with 3.5M/9600/
115200/230400/460800 bps, and recently we got a 3M bps device to test,
which needs to modify current MUL register setting, and with this
patch 2.5M/2M/1.5M/1M/0.5M should also work as they just use a MUL
value scale down from 3M's.
Also got some reference register setting from silicon guys for
different baud rates, which tries to keep the pre-scalar register value
to 16.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (as1437) fixes a bug in the usb-serial autosuspend
handling. Since the usb-serial core now has autosuspend support, it
must set the .supports_autosuspend member in every serial driver it
registers. Otherwise the usb_autopm_get_interface() call won't work.
This fixes Bugzilla #23012.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@kernel.org
Reported-by: Kevin Smith <thirdwiggin@gmail.com>
Reported-and-tested-by: Simon Gerber <gesimu@gmail.com>
Reported-and-tested-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tested on MacBookAir3,1. Without this, we get EPROTO errors when
fetching device config descriptors.
Signed-off-by: Brian Tarricone <brian@tarricone.org>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Edgar Hucek <gimli@dark-green.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the PID for the Vardaan Enterprises VEUSB422R3 USB to RS422/485
converter. It uses the same chip as the FTDI_8U232AM_PID 0x6001.
This should also work with the stable branches for:
2.6.31, 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36
Signed-off-by: Jacques Viviers <jacques.viviers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Default llseek operation behavior was changed by the patch named
"vfs: make no_llseek the default" after the yurex driver had been merged,
so the llseek to yurex is now ignored.
This patch add llseek fop with default_llseek to yurex driver
to catch up to the change.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another variant of the RT Systems programming cable for ham radios.
Signed-off-by: Michael Stuermer <ms@mallorn.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
passing argument 2 of 'dma_map_single' discards qualifiers from pointer target type
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix kernel-doc warning for set_consumer_device_supply():
Warning(drivers/regulator/core.c:912): missing initial short description on line:
* set_consumer_device_supply: Bind a regulator to a symbolic supply
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Singular Message is 16 bits:
DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
Current implementation return immedially after sucessfuly write MSB part.
To properly set mode, we need to write the complete message ( MSB and LSB ).
In twl.h, now we have defines for PM Master module register offsets,
use it instead of hard coded 0x15/0x16.
Use "message & 0xff" to ensure we send correct value for LSB.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Lesly Arackal Manuel <leslyam@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch add locks around regulator supply enable.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Integer division will truncate the result, this patch ensures we have
enough delay time for enabling regulator.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We already have device_remove_file() in error path,
no need to call it before goto link_name_err.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a disable failure when regulator supply is used.
A while loop in regulator disable checks for supply pointer != NULL
but the pointer is not always updated, resulting in the while loop
running too many times causing a disable failure.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
