This patch changes Line In as Out Switch and Mic In as Out Switch to
enums for consistency, and causes all mic and line in ports to be probed
and controls to be added appropriately.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICH6_GCTL_RESET was wrongly set to another bit by the commit
b21fadb9c1. This caused a problem when
the codec needs really a reset (e.g. recovering from the communication
error at probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added some missing register bits definitions to reduce magic numbers.
Also renamed some to follow the names on the datasheet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the single_cmd mode, the hardware cannot store the multiple replies
like on RIRB, thus each verb has to sync and wait for the response no
matter whether the return value is needed or not. Otherwise it may
result in a wrong return value from the previous verb.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A docking mic control is shown by default. The Compaq Presario
CQ60 laptop has no docking connector, so designate it as a
CXT5051_HP model.
This makes the phantom mixer slider disappear.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a debug mode to make the codec communication
synchronous. Define SND_HDA_SUPPORT_SYNC_WRITE in hda_codec.c,
and the call of snd_hda_codec_write*() will become synchronous,
i.e. wait for the reply from the codec at each time issuing a verb.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the single_cmd mode, the current driver code doesn't do any update
for RIRB just for any safety reason. But, actually the RIRB and
single_cmd mode don't conflict. Unsolicited events can be delivered
even while using the single_cmd mode.
This patch allows the handling of unsolicited events with single_cmd
mode, just always checking RIRB independent from single_cmd flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec communication error occurs, the CORB/RIRB counters should
be reset first before re-issuing the verb. Simply call azx_free_cmd_io()
and azx_init_cmd_io() to achieve that.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Realtek codecs like ALC861 seem to support only VREF50 while the
current driver assumes it's only VREF80. Check other VREF bits to set
the correct value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for the headphone volume control on IDT/STAC codecs
resulted in the removal of invalid "Side" volume eventually. But,
if the front panel doesn't exist, this setup could be regarded as a
sort of regression, as reported in kernel bug #13250.
Now as a workaround, a new model 5stack-no-fp is added so that the user
without the front panel can choose this one explicitly.
Reference: bko#13250
http://bugzilla.kernel.org/show_bug.cgi?id=13250
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS W5Fm needs the fixed codec-slots to probe to override the BIOS
problem like W5F.
Tested-by: Alp Kılıç <kilic.alp@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The digital beep tone is calculated in two different ways depending
on the codec chip. The standard one is using a divider, and another
one is a linear tone for IDT/STAC codecs. Currently, only the
latter type is used for all codecs, which resulted in a wrong tone
pitch.
This patch adds the calculation of the standard HD-audio type.
Also clean-up the fields in hda_beep struct.
Reference: bko#13162
http://bugzilla.kernel.org/show_bug.cgi?id=13162
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add proper prefix to each kernel message in hda_intel.c.
Also, avoid the unneeded prefix when CONFIG_SND_VERBOSE_PRINTK is used
together with snd_print*().
Reference: bko#13207
http://bugzilla.kernel.org/show_bug.cgi?id=13207
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for MacBook 3,1 sound by adding a model new
"mb31" with the appropriate init verbs, mixers and channel modes to
the ALC883 configuration. patch_alc882() and patch_alc883() are
modified to handle the MacBook 3,1 sound-chip (Realtek ALC889A)
correctly.
Signed-off-by: Torben Schulz <public@letorbi.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI entries of Creative with HD-audio class can be the devices
with emu20k1/emu20k2 chips. These are supported better by snd-ctxfi
driver. With that driver, the device will mutate from HD-audio to
its native class.
This patch adds a simple ifdef to avoid the conflict of device probe
between snd-hda-intel and snd-ctxfi drivers. 1102:0009 seems still
OK to be added as it has no emu20kx chip, and is a pure HD-audio
device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split the name string in hda_codec struct to vendor_name and chip_name
strings to be stored directly from the preset name.
Since mostly only the chip name is referred in many patch_*.c, this
results in the reduction of many codes in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a mixer control for the STAC92XX boards to control the
DC bias of mic ports, allowing recording from both powered and
non-powered sources. It replaces the "Mic Output Switch" with "Mic Jack
Mode" to switch between Mic, Line In, and Line Out.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the codec SSID for MacBook Pro 5,1 as compatible as MP51.
However, the headphone auto-muting function doesn't work. So,
this is just a tentative solution.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The model=acer for ALC883/889 doesn't work well for the recent Acer
Aspire laptops. Since model=auto works better nowadays, it's safer
to use the default fallback instead of the Acer specific one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add specific configuration for Samsung NC10 mini notebook. Internal
mic/speakers will be correctly muted when plugging in external ones.
Mixer controls are added for speakers, headphones and PC beep.
"Boost" is added for the microphones.
Signed-off-by: Chris Pockelé <chris.pockele.f1@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing descriptions and the model names for Realtek codecs
to the documentation and the config table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of unsol handlers defined in patch_realtek.c can be classified to
two types, mute via amp of pins and mute via ctl bits of pins.
Thus there are a big room to generalize each implementation.
This patch creates two generic functions, alc_automute_amp() and
alc_automute_pin(). The latter is actually changed from the previous
alc_sku_automute(). Each caller needs to initialize hp_pins and
speaker_pins properly at own init_hook.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The speaker auto-muting per HP plugging for ALC262 HIPPO and compatible
devices is slightly buggy as the "Master" or "Front" mixer control can
still toggle the speaker output even if the headphone is plugged.
This patch fixes the issue, and clean up the hippo-related codes
together with fixes of some inconsistent mixer names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA VT1708S and VT1702 codecs can have two SPDIF outputs. One of them
should have been handled as the extra digital out, but it's not
properly accessed.
This patch fixes the handling of the secondary SPDIF on these codecs
with the slave dig-out as found in patch_sigmatel.c. This makes the
use of such a device easier (for normal users).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on Mac Mini Core2 Duo sets both INPUT and OUTPUT pinctl bits to
the line-in jack, and it confuses the driver as if it's a valid input.
This patch adds the check of OUTPUT bit so that the driver fixes the
invalid pin setup.
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commmit dfed0ef9b3 was reverted
accidentally by the merge of auto-detection fix patch.
Fixed again now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable auto-muting in model=auto only for devices with HP and speakers.
For devices with HP and line-outs, don't enable the auto-muting.
Also, add a debug print to show the auto-mute feature.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the realtek auto-probing mode, the initialization of amp with
some magic COEF or EAPD verbs is applied only when the codec SSID
has valid values to satisfy the realtek's definition.
However, many devices don't provide in that way, thus the device
doesn't work as is.
This patch allows the same initialization code even if the SSID
doesn't pass the bit test. Also, alc_subsystem_id() is changed
just to check and define the type, so that it's called in the
parser, instead of the initializer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current ad1884a-mobile model has a problem that the speaker output
doesn't work sometimes after boot or power-saving on some HP laptops.
It seems that the verbs accessing to the non-functional widgets cause
this problem.
This patch simplifies the init verbs for mobile model not to touch
unnecessary setups so that it avoids the speaker-mute problem.
Reference: Novell bnc#495668
https://bugzilla.novell.com/show_bug.cgi?id=495668
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current error-recovery scheme for the codec communication errors
doesn't work always well. Especially falling back to the
single-command mode causes the fatal problem on many systems.
In this patch, the problematic verb is re-issued again after the error
(even with polling mode) instead of the single-cmd mode. The
single-cmd mode will be used only when specified via the command
option explicitly, mainly just for testing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
