Change setting for 400KHz frequency support by more accurate value.
Fixes: 66b0c2846b ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Value for getting frequency capability wrongly has been taken from
register offset instead of register value.
Fixes: 66b0c2846b ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In the commit be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust
support"), we miss setting OFFSET_EXT_CONF register if
i2c->dev_comp->timing_adjust is false, now add it back.
Fixes: be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust support")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
"I2C has a smaller pull reuest this time:
- new driver for I2C virtio
- removal of PMC SMP driver because platform is already gone
- IRQ probing and DMAENGINE API cleanups
- add SI metric prefix definitions to units.h
- beginning of i801 refactorization
- a few driver improvements"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (28 commits)
i2c: cadence: Implement save restore
i2c: xlp9xx: fix main IRQ check
i2c: mt65xx: fix IRQ check
i2c: virtio: add a virtio i2c frontend driver
i2c: hix5hd2: fix IRQ check
i2c: s3c2410: fix IRQ check
i2c: iop3xx: fix deferred probing
i2c: synquacer: fix deferred probing
i2c: sun6i-pw2i: Prefer strscpy over strlcpy
i2c: remove dead PMC MSP TWI/SMBus/I2C driver
i2c: dev: Use sysfs_emit() in "show" functions
i2c: dev: Define pr_fmt() and drop duplication substrings
i2c: designware: Fix indentation in the header
i2c: designware: Use DIV_ROUND_CLOSEST() macro
units: Add SI metric prefix definitions
i2c: at91: mark PM ops as __maybe unused
i2c: sh_mobile: : use proper DMAENGINE API for termination
i2c: qup: : use proper DMAENGINE API for termination
i2c: mxs: : use proper DMAENGINE API for termination
i2c: imx: : use proper DMAENGINE API for termination
...
The zynqmp platform now supports chip-off so the registers can
lose context.
Implement save restore for i2c module.
Since we have only a couple of registers
an unconditional restore is done.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0 for the main IRQ, the driver's probe()
method will return 0 early (as if the method's call was successful).
Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always
override that decision...
Fixes: 2bbd681ba2 ("i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39 ("I2C: mediatek: Add driver for MediaTek I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add an I2C bus driver for virtio para-virtualization.
The controller can be emulated by the backend driver in
any device model software by following the virtio protocol.
The device specification can be found on
https://lists.oasis-open.org/archives/virtio-comment/202101/msg00008.html.
By following the specification, people may implement different
backend drivers to emulate different controllers according to
their needs.
Co-developed-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Jie Deng <jie.deng@intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: 15ef27756b ("i2c: hix5hd2: add i2c controller driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec9785 ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When adding the code to handle platform_get_irq*() errors in the commit
489447380a ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated. The safe
replacement is strscpy().
This is a previous step in the path to remove the strlcpy() function
entirely from the kernel [1].
[1] https://github.com/KSPP/linux/issues/89
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 1b00767fd8 ("MIPS: Remove PMC MSP71xx platform") removes the
config PMC_MSP in ./arch/mips/Kconfig.
Hence, since then, the corresponding PMC MSP TWI/SMBus/I2C driver is
dead code. Remove this dead driver.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In couple of places the indentation makes harder to read the code.
Fix it to be sane.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of open-coding DIV_ROUND_CLOSEST() and similar use the macros directly.
While at it, replace numbers with predefined SI metric prefixes.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver uses pm_ptr(), so the PM ops could be unused.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: dab4b0e8c9 ("i2c: at91: remove #define CONFIG_PM")
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove #define CONFIG_PM and use __maybe_unused for PM functions and
pm_ptr() for PM ops.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch to use module_parport_driver() to reduce boilerplate code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If a user is interested in such details he can enable smbus tracing.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
p2sb_spinlock is used in i801_add_tco_spt() only, and in process context
only. Therefore a mutex is sufficient, and we can make the definition
local to i801_add_tco_spt().
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Setting the autosuspend delay to a negative value disables runtime pm in
a little bit smarter way, because we need no cleanup when removing the
driver. Note that this is safe when reloading the driver, because the
call to pm_runtime_set_autosuspend_delay() in probe() will reverse the
effect. See update_autosuspend() for details.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver is written as if platform_get_irq() returns 0 on errors (while
actually it returns a negative error code), blithely passing these error
codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with
-EINVAL. Add the necessary error check to the pre-existing *if* statement
forcing the driver into the polling mode...
Fixes: 4ad48e6ab1 ("i2c: Renesas Highlander FPGA SMBus support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Bit SMBHSTCNT_PEC_EN is used only if software calculates the CRC and
uses register SMBPEC. This is not supported by the driver, it supports
hw-calculation of CRC only (using bit SMBAUXSTS_CRCE). The chip spec
states the following, therefore never set bit SMBHSTCNT_PEC_EN.
Chapter SMBus CRC Generation and Checking
If the AAC bit is set in the Auxiliary Control register, the PCH
automatically calculates and drives CRC at the end of the transmitted
packet for write cycles, and will check the CRC for read cycles. It will
not transmit the contents of the PEC register for CRC. The PEC bit must
not be set in the Host Control register. If this bit is set, unspecified
behavior will result.
This patch is based solely on the specification and compile-tested only,
because I have no PEC-capable devices.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
During some transfers the bus can still be busy when an interrupt is
received. Commit 763778cd79 ("i2c: mpc: Restore reread of I2C status
register") attempted to address this by re-reading MPC_I2C_SR once but
that just made it less likely to happen without actually preventing it.
Instead of a single re-read, poll with a timeout so that the bus is given
enough time to settle but a genuine stuck SCL is still noticed.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- core supports now bus regulators controlling power for SCL/SDA
- quite some DT binding conversions to YAML
- added a seperate DT binding for the optional SMBus Alert feature
- documentation with examples how to deal with I2C sysfs files
- some bigger rework for the i801 driver
- and a few usual driver updates
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (42 commits)
i2c: ali1535: mention that the device should not be disabled
i2c: mpc: Restore reread of I2C status register
i2c: core-smbus: Expose PEC calculate function for generic use
Documentation: i2c: Add doc for I2C sysfs
i2c: core: Disable client irq on reboot/shutdown
dt-bindings: i2c: update bindings for MT8195 SoC
i2c: imx: Fix some checkpatch warnings
i2c: davinci: Simplify with dev_err_probe()
i2c: cadence: Simplify with dev_err_probe()
i2c: xiic: Simplify with dev_err_probe()
i2c: cadence: Clear HOLD bit before xfer_size register rolls over
dt-bindings: i2c: ce4100: Replace "ti,pcf8575" by "nxp,pcf8575"
i2c: i801: Improve i801_setup_hstcfg
i2c: i801: Use driver name constant instead of function dev_driver_string
i2c: i801: Simplify initialization of i2c_board_info in i801_probe_optional_slaves
i2c: i801: Improve status polling
i2c: cht-wc: Replace of_node by NULL
i2c: riic: Add RZ/G2L support
dt-bindings: i2c: renesas,riic: Document RZ/G2L I2C controller
dt-bindings: i2c: renesas,iic: Convert to json-schema
...
The comment from the i801 driver is valid here, too, so copy it.
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Prior to commit 1538d82f46 ("i2c: mpc: Interrupt driven transfer") the
old interrupt handler would reread MPC_I2C_SR after checking the CSR_MIF
bit. When the driver was re-written this was removed as it seemed
unnecessary. However as it turns out this is necessary for i2c devices
which do clock stretching otherwise we end up thinking the bus is still
busy when processing the interrupt.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the OSIFI2C_SET_BIT_RATE and OSIFI2C_STOP requests which erroneously
used the osif_usb_read() helper and set the IN direction bit.
Reported-by: syzbot+9d7dadd15b8819d73f41@syzkaller.appspotmail.com
Fixes: 83e53a8f12 ("i2c: Add bus driver for for OSIF USB i2c device.")
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the following warnings reported by checkpatch::
drivers/i2c/busses/i2c-imx.c:173: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:175: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:176: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:177: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:455: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:602: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:638: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1170: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1374: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1398: WARNING: Prefer strscpy over strlcpy - see: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On Xilinx zynq SOC if the delay between address register write and
control register write in cdns_mrecv function is more, the xfer size
register rolls over and controller is stuck. This is an IP bug and
is resolved in later versions of IP.
To avoid this scenario, disable the interrupts on the current processor
core between the two register writes and enable them later. This can
help achieve the timing constraint.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We need to add a check for if the kzalloc() fails.
Fixes: 4a7695429e ("i2c: cp2615: add i2c driver for Silicon Labs' CP2615 Digital Audio Bridge")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bence Csókás <bence98@sch.bme.hu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As explained in [0] currently we may leave SMBHSTSTS_INUSE_STS set,
thus potentially breaking ACPI/BIOS usage of the SMBUS device.
Seems patch [0] needs a little bit more of review effort, therefore
I'd suggest to apply a part of it as quick win. Just clearing
SMBHSTSTS_INUSE_STS when leaving i801_access() should fix the
referenced issue and leaves more time for discussing a more
sophisticated locking handling.
[0] https://www.spinics.net/lists/linux-i2c/msg51558.html
Fixes: 01590f361e ("i2c: i801: Instantiate SPD EEPROMs automatically")
Suggested-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i801_setup_hstcfg() leaves the bits in priv->original_hstcfg that
we're interested in intact. Therefore we can remove the return value
from the function and use priv->original_hstcfg directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We are the driver, so we can use the driver name directly instead of
retrieving it by calling dev_driver_string().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Why shall we bother to open-code something that the compiler can do for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Polling uses the same timeout as irq mode: 400 * 500us = 200ms = HZ / 5.
So let's use the adapter->timeout value also for polling. This has the
advantage that userspace can control the timeout value for polling as
well. In addition change the code to make it better readable.
Last but not least remove the timeout debug messages. Calls to both
functions are followed by a call to i801_check_post() that will print
an error message in case of timeout.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver is run on the platforms where OF node is always NULL.
The confusion comes from IRQ domain APIs that take either OF or
firmware node as input parameter. Since fwnode is not used here
either, replace of_node by NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
RZ/G2L i2c controller is compatible with RZ/A i2c controller.
By default IP is in reset state, so need to perform release
reset before accessing any register.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Mark bus as suspended during system suspend to block the future
transfers. Implement geni_i2c_resume_noirq() to resume the bus.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the hardware is still accessing memory after SMMU translation
is disabled (as part of smmu shutdown callback), then the
IOVAs (I/O virtual address) which it was using will go on the bus
as the physical addresses which will result in unknown crashes
like NoC/interconnect errors.
So, implement shutdown callback for i2c driver to suspend the bus
during system "reboot" or "shutdown".
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
