Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Multiple options depend on I2C but are already under under if I2C. Remove
those useless dependencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some entries in the Kconfig are improperly indented with spaces instead of
tabs.
Also fix whitespaces in Makefile.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Gcc is unable to prove that alm_pending is always initialized
when it is used, so it prints a harmless warning:
drivers/rtc/rtc-pcf8563.c: In function 'pcf8563_probe':
drivers/rtc/rtc-pcf8563.c:449:5: warning: 'alm_pending' may be used uninitialized in this function [-Wmaybe-uninitialized]
This uses the same conditional expression that is used inside of
the pcf8563_get_alarm_mode() function, to help gcc figure it out
and shut up that warning, and make the ARM defconfigs build again
with no warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a45d528aab ("rtc: pcf8563: clear expired alarm at boot time")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alarm interrupt enable register is at offset 0x7, while the time
registers for the alarm follow that. When we program Alarm interrupt
enable prior to programming the time, it is possible that previous
time value could be close or match at the time of alarm enable
resulting in interrupt trigger which is unexpected (and does not match
the time we expect it to trigger).
To prevent this scenario from occuring, program the ALM0_EN bit only
after the alarm time is appropriately programmed.
Ofcourse, I2C programming is non-atomic, so there are loopholes where
the interrupt wont trigger if the time requested is in the past at
the time of programming the ALM0_EN bit. However, we will not have
unexpected interrupts while the time is programmed after the interrupt
are enabled.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Sometimes the irq line is not connected to any soc-pin. This does
not hinder basic timekeeping functionality of the rtc, so probe
should not fail in this case.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use resource_size function on resource object instead of explicit
computation.
No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver can't accommodate the 12 hour mode but the error message states
that the 24 hour mode is not supported.
Also fix the typos (hour vs hours).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use bit instead of hand coding the shift and correct the 24 hour vs 24
hours typo.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-efi driver declares that the EFI 'epoch' is 1/1/1998, but
the UEFI spec does not define it at all. It does define a range of
[1900, 9999] for the 'Year' member of the EFI_TIME struct, so let's
use 1900 as the minimum year and not 1998.
Also, move the validation of the year to the convert_from_efi_time()
routine where all other EFI_TIME fields are validated as well.
This prevents rtc_read_time() failures when the RTC that backs the
EFI time services is set to a date before 1998, e.g., when it has
lost power.
This also optimizes the compute_wday() routine, by replacing the for
loop with a simple arithmetic expression, and by reusing the yearday
value that we need to compute anyway when populating the
rtc_time::tm_yday field.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now rtc_set_mmss() has no users, just remove it.
We still have rtc_set_time() doing similar things.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, CONFIG_RTC_SYSTOHC uses CONFIG_RTC_HCTOSYS_DEVICE which
is originally used by CONFIG_RTC_HCTOSYS, but this rtc device has
some limiations, for example, it must be battery-backed, be able
to work with irq off and through system suspension, etc.
So add CONFIG_RTC_SYSTOHC_DEVICE used exclusively for CONFIG_RTC_SYSTOHC,
it is more lenient compared to CONFIG_RTC_HCTOSYS_DEVICE, and could
be assigned any available RTC in the system.
Default value is CONFIG_RTC_HCTOSYS_DEVICE which is "rtc0" by default.
After this patch, NTP will sync up "rtc0" by default.
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
sunxi_rtc_setalarm() uses deprecated rtc_tm_to_time(),
which will overflow in year 2106 on 32-bit machines.
This patch solves this by:
- Replacing rtc_tm_to_time() with rtc_tm_sub()
Also remove the unnecessary initial zeroing of some
local variables in sunxi_rtc_setalarm().
Cc: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
isl1208_i2c_set_alarm() uses deprecated rtc_tm_to_time(),
which will overflow in year 2106 on 32-bit machines.
This patch solves this by:
- Replacing rtc_tm_to_time() with rtc_tm_sub()
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf8563_rtc_set_alarm() uses deprecated rtc_tm_to_time()
and rtc_time_to_tm(), which will overflow in year 2106
on 32-bit machines.
This patch solves this by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Initialise the variable high_bb_charging before using it to avoid
configuring wrong value and fix following compilation warning:
/*
rtc-palmas.c: In function ‘palmas_rtc_probe’:
rtc-palmas.c:242:7: warning: ‘high_bb_charging’ may be used
uninitialized in this function
*/
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[viresh.kumar@linaro.org: acked rtc-spear]
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Return -EINVAL if the voltage low bit is set to avoid getting a bogus
time at boot.
There was a comment stating that util-linux hwclock refuses to set a
new time if we return an error code on read, but at least the current
version do set the time as expected. Remove the comment and the check
for valid time, and let the rtc core check it for us.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Driver for the on chip RTC found on Cortina's SoC Gemini.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
[alexandre.belloni@free-electrons.com: use devm_request_irq() and remove
useless goto]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When entering suspend while an wakeup alarm is set, enable_set_wake
should make sure that the RTC interrupt keep being enabled and the
.irq_set_wake for the RTC interrupt get called. However, since the
driver uses the suspend_noirq callback, the call to enable_irq_wake
has been made after disabling the interrupts. While .irq_set_wake
has been called properly, the interrupt remained disabled.
Use the suspend callback to call enable_irq_wake early enough to
ensure the RTC interrupt remains enabled.
Fixes: 7654e9d4fd ("drivers/rtc/rtc-snvs: fix suspend/resume")
Cc: <stable@vger.kernel.org> # 3.19
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Using gpio_request_array()/gpio_free_array() can make the code
simpler because it can set the direction and initial value
in one shot and the for loop is unnecessary.
Also, struct v3020_gpio is removed, because the struct v3020_gpio
is replaced with struct gpio.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Drivers should not be using the __raw_* io accessors.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the rtc-max77802 driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the platform ID table so the module contains that data.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the rtc-max77686 driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the platform ID table so the module contains that data.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to
modules.alias:
alias i2c:ds1672 rtc_ds1672
alias i2c:max6900 rtc_max6900
alias platform:lp3974-rtc rtc_max8998
alias platform:max8998-rtc rtc_max8998
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On some !ARM 32bits platforms, the following compilation error happens
because of the division on a 64bits value in mtk_rtc_read_time():
drivers/built-in.o: In function `mtk_rtc_read_time':
rtc-mt6397.c:(.text+0x265d13f): undefined reference to `__divdi3'
rtc-mt6397.c:(.text+0x265d150): undefined reference to `__moddi3'
Use div_s64() as done in rtc_time64_to_tm() to solve that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to C99, %2.s means 'print two spaces' (a precision of
. without following digits or * means 0). The kernel's printf
implementation, however, treats that case as if no precision was
given, but relying on that quirk is rather silly. Also, since no -
(aka left-justify) flag is given, the field with of 2 would then cause
the alarm->enabled case to come out as "o n". Deobfuscate it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch updates the email address of the rtc-at32ap700x driver supported by
me to an email account I will use on a more regular basis in the future.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the DryICE unit is locked it is impossible to set the time. Provide an
error message for this case.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Maybe the unit enters the hardware related state at runtime and not at
system boot time (after a power cycle).
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This code is required to recover the unit from a security violation.
Hopefully this code can recover the unit from a hardware related invalid
state as well.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Be independent of the endianness of the kernel.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are now no differences between RTC on Exynos3250 and S3C6410.
Merge everything into one so duplicated code could be removed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc_timer_cancel() always returns 0 and cannot fail (calls only
other void-returning functions).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
While setting the time, the RTC TIME register should not be accessed.
However due to hardware constraints, setting the RTC time involves
sleeping during 100ms. This sleep was done outside the critical section
protected by the spinlock, so it was possible to read the RTC TIME
register and get an incorrect value. This patch introduces a mutex for
protecting the RTC TIME access, unlike the spinlock it is allowed to
sleep in a critical section protected by a mutex.
The RTC STATUS register can still be used from the interrupt handler but
it has no effect on setting the time.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org> [4.0]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a basic driver for the ultra-low-power Abracon AB x80x series of RTC
chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor/
battery charger.
[arnd@arndb.de: abx805 depends on i2c]
[alexandre.belloni@free-electrons.com: renam buffer from date to buf in abx80x_rtc_read_time()]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ST's Low Power Controller (LPC) controls two devices; watchdog and RTC.
Only one of the devices can be used at any one time. This is enforced
by the correlating MFD driver. This portion of the driver-set controls
the Real Time Clock.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
