According to DP spec, it is not required in the Link Training
procedure.
[jg1.han@samsung.com: modified the commit message]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Fix a bug where we check !dp->irq instead of the correct check for
-ENXIO.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
EDID error handling has 2 problems:
- It doesn't fail as early as it can
- The retry counts for i2c and aux transactions are huge
This patch fails if the initial i2c transaction fails, and reduces the
aux and i2c retry counts down to 3.
[jg1.han@samsung.com: reduced the retry count of exynos_dp_read_byte_from_dpcd()]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
According to the exynos datasheet (Figure 49-10), we should wait for PLL
lock before programming the training pattern when doing software eDP
link training.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Clean up some of the SW training code to make it more clear and reduce
duplicate code.
[jg1.han@samsung.com: used exynos_dp_write_bytes_to_dpcd()]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Add return code checks to the DPCD transactions in the SW link training
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch enables device tree based discovery support for DP driver.
The driver is modified to handle platform data in both the cases:
with DT and non-DT.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add dss_get_core_pdev() which returns the platform device for dss core
device. The following patches use the core pdev to register sysfs files
in the compat code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move display sysfs related code from display.c to display-sysfs.c, for
clarity. The sysfs code will only be used for compat mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes dispc_ovl_calc_scaling to get pclk and lclk as
parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes calc_scaling to get pclk and lclk as parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes check_horiz_timing_omap3() to get pclk and lclk as
parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes calc_core_clk() function to get pclk as a parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the dispc_plane_pclk_rate and dispc_plane_lclk_rate functions to
return 0 if the given plane is the writeback plane. The clocks are not
valid for WB, but returning 0 from these functions instead of running
into BUG() will simplify the code that uses these functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_go() should never be called with manager output disabled or if
the GO bit is already set. Change the current silent returns to
WARN_ONs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of doing direct register reads/writes, dispc_wb_enable() and
dispc_wb_is_enabled() functions can use the common overlay functions to
set and check the enable bit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
WB will not be used with compat-mode, i.e. from omapfb. This means we
don't need the current complex dispc_wb_enable function, but can have a
simple register write version of the function.
This patch removes all the extra code from dispc_wb_enable()
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_disable_digit_out() needs to wait until the DIGIT output is
turned off. This is done with either VSYNC irq on OMAP2/3 and
FRAMEDONETV on OMAP4+. It currently uses a rather hacky way to decide
what irq to use.
This patch changes dispc_mgr_disable_digit_out to use
dispc_mgr_get_framedone_irq to find out if there's framedone irq on this
SoC, and if not, uses VSYNC.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2/3 do not have FRAMEDONETV irq, but later omaps do. We currently
always return 0 from dispc_mgr_get_framedone_irq() for TV output to be
compatible with OMAP2/3.
This patch implements "no_framedone_tv" dispc-feature that is used in
dispc_mgr_get_framedone_irq to return either 0 for OMAP2/3, or the
correct IRQ number for FRAMEDONETV on OMAP4+.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_get_dsidev_from_id() gives a WARN if DSI support is not compiled in.
This warning is not right, as it's valid to call
dsi_get_dsidev_from_id() to see if there is DSI support or not.
Remove the WARN().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the DSI support has not been compiled in or the SoC doesn't have DSI
hardware, dpi_get_dsidev() returns NULL. This NULL is passed to
dpi_verify_dsi_pll() causing a crash. The bug was added with commit
0e8276ef75 (OMAPDSS: DPI: always use DSI
PLL if available).
Fix this by checking if dsidev is NULL before calling
dpi_verify_dsi_pll().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove dispc_mgr_is_channel_enabled() and dss_mgr_get_timings()
declarations, as the function doesn't exist.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'fbdev-next' of github.com:timur-tabi/linux-2.6:
drivers/video: fsl-diu-fb: store EDID data in the global object
drivers/video: fsl-diu-fb: don't touch registers for unused features
drivers/video: fsl-diu-fb: clean up reset of primary display
drivers/video: fsl-diu-fb: remove unused 'cursor_reset' variable
drivers/video: fsl-diu-fb: improve message displays
drivers/video: fsl-diu-fb: streamline enabling of interrupts
drivers/video: fsl-diu-fb: add support for set_gamma ioctls
drivers/video: fsl-diu-fb: simplify platforms that have only one port
MAINTAINERS: Make Timur Tabi the maintainer for the Freescale DIU driver
do clk_get on connection id "fck" to support OMAP based
platforms having multiple clocks for module. Without this
driver change clk_get fails on am335x.
This patch is based on the discussion in community
http://marc.info/?l=linux-kernel&m=135166018907827&w=2
Signed-off-by: Manjunathappa <prakash.pm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Configure below LCDC configurations to optimal values, also have an
option configure these optional parameters for platform.
1) AC bias configuration: Required only for passive panels
2) Dma_burst_size:
3) FIFO_DMA_DELAY:
4) FIFO threshold: Does not apply for da830 LCDC.
Patch is verified for 16bpp and 24bpp configurations on da830, da850 and
am335x EVMs.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adopt fb_videomode data instead of defining driver private
structure to hold panel information. This is the way standard FB
drivers maintain the panel information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge SH Mobile LCDC patches from Laurent.
* 'lcdc-next' of git://linuxtv.org/pinchartl/fbdev:
fbdev: sh_mobile_lcdc: Make sh_mobile_lcdc_sys_bus_ops static
sh: kfr2r09: Use the backlight API for brightness control
ARM: mach-shmobile: ag5evm: Use the backlight API for brightness control
fbdev: sh_mobile_lcdc: Remove unused get_brightness pdata callback
sh: ecovec24: Remove unused get_brightness LCDC callback
sh: ap325rxa: Remove unused get_brightness LCDC callback
ARM: mach-shmobile: mackerel: Removed unused get_brightness callback
fbdev: sh_mobile_lcdc: Store the backlight brightness internally
fbdev: sh_mipi_dsi: Remove the unused sh_mipi_dsi_info lcd_chan field
ARM: mach-shmobile: Remove the unused sh_mipi_dsi_info lcd_chan field
fbdev: sh_mipi_dsi: Remove last reference to LCDC platform data
fbdev: sh_mipi_dsi: Use the LCDC entity default mode
fbdev: sh_mipi_dsi: Use the sh_mipi_dsi_info channel field
ARM: mach-shmobile: Initiliaze the new sh_mipi_dsi_info channel field
fbdev: sh_mipi_dsi: Add channel field to platform data
ARM: mach-shmobile: ag5evm: Add LCDC tx_dev field to platform data
fbdev: sh_mobile_lcdc: Remove priv argument from channel and overlay init
fbdev: sh_mobile_lcdc: Rename mode argument to modes
fbdev: sh_mobile_lcdc: Get display dimensions from the channel structure
fbdev: sh_mobile_lcdc: use dma_mmap_coherent
Although the DIU driver creates five framebuffer devices, only the first
one controls the physical display. The remaining four are virtual "AOIs".
Therefore, the EDID data should be stored in the global fsl_diu_data
object, instead of the per-framebuffer object.
Signed-off-by: Timur Tabi <timur@freescale.com>
We don't use the writeback buffer, so don't initialize the registers for
that feature.
The default value for SYN_POL is already zero, so don't re-initialize it.
Writing the INT_STATUS register does nothing.
The value that we write to the PLUT register only makes sense on the
MPC8610 and P1022, so don't touch that register on the MPC5121.
Signed-off-by: Timur Tabi <timur@freescale.com>
Commit 4b5006ec ("shared DIU framebuffer support") added the ability to
retain the splash screen until the framebuffer is opened by user space.
Clean up this code to eliminate redundant writes to registers, and eliminate
the use of dummy area descriptor.
Signed-off-by: Timur Tabi <timur@freescale.com>
Remove functions request_irq_local() and free_irq_local(), and merge
their code into the functions that handle opening and closing the
framebuffer. We also improve the way that interrupts are enabled.
Also implement a work-around for broken U-Boots that leave the DIU
interrupts enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
The MPC5121 BSP comes with a gamma_set utility that initializes the gamma
table via an ioctl. Unfortunately, the ioctl number that utility uses
is defined improperly, but we can still support it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Allow the platform code not to define a value for diu_ops.set_monitor_port.
This would be for platforms that only have one monitor port.
set_monitor_port() will never be called with an unsupported port anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Green pixel and blue pixel are 3 bits and 2 bits respectively
at ARGB232 format. Thus, the value of red offset should be 5,
not 4. Also, the value of red length should be 2, because
red pixel is 2 bits at ARGB232 format.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch returns an error, when bpp is invalid in
s3c_fb_check_var(). If invalid bpp is requested,
an error should be returned.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Because there is no need to access to the platform device in
suspend/resume and runtime_suspend/resume, dev_get_drvdata()
can be used instead of platform_get_drvdata() to make the code
smaller.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch uses FIMD_V8_VIDTCON0 as the address definition
of VIDTCON0 register, because the address offset of VIDTCONx
registers is changed from 0x0 to 0x20000 for EXYNOS5 FIMD.
So, FIMD_V8_VIDTCON0 should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
The help message of config FB_S3C_DEBUG_REGWRITE is fixed,
because printk(KERN_DEBUG) was replaced with pr_debug().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Merge my own merge branch to get various fixes from there
and upstream, especially the hvc console tty refcouting fixes
which which testing is quite a bit harder...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1jPB
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss fixes from Tomi Valkeinen:
"Here are a few OMAPDSS fixes for the next -rc. I'm sending these
directly to you, and quite late, as the fbdev tree maintainer
(Florian) has been busy with his work and hasn't had time to manage
the fb patches."
* tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: do not fail if dpll4_m4_ck is missing
OMAPFB: Fix possible null pointer dereferencing
OMAPDSS: HDMI: fix missing unlock on error in hdmi_dump_regs()
omapdss: dss: Fix clocks on OMAP363x
OMAPDSS: DSI: fix dsi_get_dsidev_from_id()
omapfb compilation fails on x86 (but not on omap):
drivers/video/omap2/omapfb/omapfb-ioctl.c: In function ‘omapfb_ioctl’:
drivers/video/omap2/omapfb/omapfb-ioctl.c:861:23: error: ‘SZ_1M’ undeclared (first use in this function)
drivers/video/omap2/omapfb/omapfb-ioctl.c:861:23: note: each undeclared identifier is reported only once for each function it appears in
Fix this by including linux/sizes.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not fail if dpll4_m4_ck is missing. The clock is not there on omap24xx,
so this should not be a hard error.
The patch retains the functionality before the commit 185bae10 (OMAPDSS:
DSS: Cleanup cpu_is_xxxx checks).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Register the DSS driver after SPI probe. This simplifies the
initialization. This is similar to what is being done e.g.
in panel-acx565akm.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
From Alexander Shiyan:
The main direction of this patchset - approaching the platform to the
possibility of using configurations with multiple platforms in a single
kernel. Added support of the majority of the necessary kernel symbol.
Also part of the driver code used only for the platform was moved to the
board code and converted to the use of standard drivers.
* clps711x/soc2:
MAINTAINERS: Add ARM CLPS711X entry
ARM: clps711x: Update defconfig due latest changes and new kernel symbols
ARM: clps711x: Rename board files to match functionality
ARM: clps711x: edb7211: Add support for NOR-Flash
ARM: clps711x: Moving backlight controls of framebuffer driver to the board
ARM: clps711x: p720t: Special driver for handling NAND memory is removed
ARM: clps711x: Moving power management of framebuffer driver to the board
ARM: clps711x: autcpu12: Special driver for handling NAND memory is removed
ARM: clps711x: Unused empty "ACK" calls for IRQ-chips removed
ARM: clps711x: Add FIQ interrupt handling
ARM: clps711x: Implement usage "MULTI_IRQ_HANDLER" kernel option for a platform
ARM: clps711x: Implement usage "SPARSE_IRQ" kernel option for a platform
ARM: clps711x: cdb89712: Special driver for handling memory is removed
ARM: clps711x: Always select AUTO_ZRELADDR for a platform
ARM: clps711x: p720t: Unneeded inclusion of head-sa1100.S removed
ARM: clps711x: Transform clps711x-framebuffer to platform driver and use it
ARM: clps711x: p720t: Using "leds-gpio" driver for LED control
ARM: clps711x: Using platform_driver for ethernet device
This patch moves the backlight controls for clps711x-framebuffer driver
to the board code. To control we use "generic-bl" driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
[olof: fixed space/tab whitespace in drivers/video/clps711xfb.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves the power management for clps711x-framebuffer driver
to the board code. To control we use "platform-lcd" driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
There's no need to query the hardware for the currenty brightness value
through a platform data callback when we can cache the value internally
in the LCDC driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The format check that references LCDC platform data isn't needed, as the
mismatch between LCDC and MIPI-DSI platform it detects would result in a
badly displayed image, which isn't worse than a complete failure to
setup the transmitter.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Configure the MIPI-DSI transmitter using the LCDC entity default mode
instead of accessing the mode through the LCDC platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Get the LCDC channel selector from the sh_mipi_dsi_info channel field
directly instead of accessing the LCDC platform data through the
lcd_chan field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The channel and overlay init functions operate on a channel and an
overlay, don't pass the priv parameter explicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The sh_mobile_lcdc_channel_fb_init() mode argument is used to pass a
list of modes, rename it to modes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Get the display dimensions directly from the channel structure instead
of recomputing them from the monitor specs or accessing the platform
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
fb_mmap() implemented in fbmem.c uses smem_start as the physical
address of the frame buffer. In the sh_mobile_lcdc driver, the
smem_start is a dma_addr_t that is not a physical address when IOMMU is
enabled. dma_mmap_coherent() maps the address correctly.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
clps711x-framebuffer driver needs to be updated and this is a first step
to make driver better. With this patch we are convert clps711x-framebuffer
to platform device and load this driver from board code.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a dispc_features struct for OMAP5. Previously, OMAP5 used the same
struct as OMAP4. The new struct for OMAP5 contains the updated register
field offset and maximum limit for overlay manager width and height.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The overlay manager width and height vary in OMAP5 from previous OMAPs
in terms of maximum limit and register field positions. Add parameters
in dispc_features for these. Also remove params related to manager width
and height from dss_features, as we want to maintain a feature list for
individual IPs.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Variable r is never set to any value different to zero.
Delete the if statement as it will never executed.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 952cbaaa9b (OMAPFB: Change
dssdev->manager references) added checks for OMAPFB_WAITFORVSYNC ioctl
to verify that the display, output and overlay manager exist. However,
the code erroneously uses && for each part, which means that
OMAPFB_WAITFORVSYNC may crash the kernel if no display, output or
manager is associated with the framebuffer.
This patch fixes the issue by using ||.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Conflicts:
drivers/video/omap2/dss/Kconfig
drivers/video/omap2/omapfb/omapfb-ioctl.c
drivers/video/omap2/omapfb/omapfb-main.c
Merge changes to make omapfb use common dma_alloc, and remove omap's
custom vram allocator.
This reverts commit 14840b9a83.
The commit breaks audio, and a new version will be applied later.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
I'm reviving an old patch from 2009 that adds support for GXT4000P and GXT6500P
adapter to the gxt4500 driver.
See threads at http://marc.info/?l=linux-fbdev-devel&m=124345080216952&w=2
and https://lists.ozlabs.org/pipermail/linuxppc-dev/2009-June/072672.html
for more details.
This patch adds support for GXT4000P and GXT6500P cards found on some
IBM pSeries machines.
GXT4000P/6000P and GXT4500P/6500P couples are identical from
software's point of view and are based on the same Raster Engine
(RC1000), except for a different reference clock for the PLL.
GXT6x00P models are equipped with an additional Geometry Engine
(GT1000) but this driver doesn't use it.
Signed-off-by: Nico Macrionitis <acrux@cruxppc.org>
Signed-off-by: Giuseppe Coviello <cjg@cruxppc.org>
Tested-by: Dan Horák <dan@danny.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use dma_alloc_attrs to allocate memory instead of omap specific vram
allocator. After this we can remove the omap vram allocator.
There are some downsides to this change:
1) dma_alloc_attrs doesn't let us allocate at certain physical address.
However, this should not be a problem as this feature of vram allocator
is only used when reserving the framebuffer that was initialized by the
bootloader, and we don't currently support "passing" a framebuffer from
the bootloader to the kernel anyway.
2) dma_alloc_attrs, as of now, always ioremaps the allocated area, and
we don't need the ioremap when using VRFB. This patch uses
DMA_ATTR_NO_KERNEL_MAPPING for the allocation, but the flag is currently
not operational.
3) OMAPFB_GET_VRAM_INFO ioctl cannot return real values anymore. I
changed the ioctl to return 64M for all the values, which, I hope, the
applications will interpret as "there's enough vram".
4) "vram" kernel parameter to define how much ram to reserve for video
use no longer works. The user needs to enable CMA and use "cma"
parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When doing a manual update in dss_mgr_start_update, we clear the shadow dirty
flags. Although there isn't any harm in clearing them. The need to clear them
out here should never arrive.
When applying configurations for a manual update manager, we never do any
register writes, i.e, calls to dss_mgr_write_regs and dss_mgr_write_regs_extra
never happen while applying. We do all these writes only when we call
dss_mgr_start_update. Hence, there is never a time when the shadow registers
are dirty.
Remove the call to mg_clear_shadow_dirty.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The bool was_updating is never really used for anything. It is set to the
current value of mp->updating, but not used anywhere. Remove this variable.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
An overlay's channel out field isn't a shadow register. The TRM says that it's
taken into effect immediately. This understanding was missing and channel out
was treated as a shadow parameter, and in overlay's private data as extra info.
Program channel out bits directly in dss_ovl_set_manager(). In order to do this
safely, we need to be totally sure that the overlay is disabled in hardware. For
auto update managers, we can assume that the overlay was truly disabled at
dss_ovl_unset_manager() through the wait_pending_extra_info_updates() call.
However, when unsetting manager for an overlay that was previously connected to
a manager in manual update, we can't be sure if the overlay is truly disabled.
That is, op->enabled might not reflect the actual state of the overlay in
hardware. The older manager may require a manual update transfer to truly
disable the overlay. We expect the user of OMAPDSS to take care of this, in
OMAPDSS, we make sure that an overlay's manager isn't unset if there if
extra_info is still dirty for that overlay.
The wrong understanding of channel out bits also explains the reason why we see
sync lost when changing an overlay's manager which was previously connected to a
manual update manager. The following sequence of events caused this:
- When we disable the overlay, no register writes are actually done since the
manager is manual update, op->enabled is set to false, and the
extra_info_dirty flag is set. However, in hardware, the overlay is still
enabled in both shadow and working registers.
- When we unset the manager, the software just configures the overlay's manager
to point to NULL.
- When we set the overlay to a new manager(which is in auto update) through
dss_ovl_set_manager, the check for op->enabled passes, the channel field in
extra info is set to the new manager. When we do an apply on this manager,
the new channel out field is set in the hardware immediately, and since the
overlay enable bit is still set in hardware, the new manager sees that the
overlay is enabled, and tries to retrieve pixels from it, this leads to sync
lost as it might be in the middle of processing a frame when we set the
channel out bit.
The solution to this was to ensure that user space does another update after
disabling the overlay, this actually worked because the overlay was now truly
disabled, and an immediate write to channel out didn't impact since the manager
saw the new overlay as disabled, and doesn't try to retrieve pixels from it.
Remove channel as an extra_info field. Make dss_ovl_unset_manager more strict
about the overlay being disabled when detaching the manager. For overlays
connected to a manual update manager, unset_manager fails if we need another
update to disable the overlay.
We still need to a manual update to ensure the overlay is disabled to get change
the overlay's manager. We could work on doing a dummy update by using DISPC's
capability to gate the different video port signals. This is left for later.
Remove the comment about the sync lost issue.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When calculating row and pixel increments for graphics and video pipes, we need
to consider the dimensions of the input frame to know how to read from the
buffer. Hence, we need to calculate these parameters from the input to the
pipeline.
For writeback, the row and pixel increments need to be calculated based on the
output of the writeback pipeline, i.e, the dimensions of the frame after
scaling. Ensure that dispc driver uses values of out_width and out_height when
calling calc_dma/calc_tiler_rotation_offset.
For graphics and video pipes, the original code passed the original height as
frame_height to calc_dma_rotation_offset, and not the predecimated height. This
is left as it is for now. We need to figure out why pre decimated height isn't
needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since writeback writes to a buffer instead of reading from one, predecimation
doesn't make sense for it. Configure the width and height predecimation limits
to 1 if the plane is writeback.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_calc_scaling_44xx() doesn't work correctly for writeback. There are
two issues with it:
- the function tries to calculate pixel clock for the input plane using
dispc_plane_pclk_rate(), calling this with writeback as input plane results in
a BUG(), this function shouldn't be called for writeback at all. Fix this by
calculating pixel clock only when we are not in mem to mem mode.
- the maximum input_width is the product of the downscale ratio supported and
the and the given output_width. This was calculated incorrectly by dividing
output_width with maxdownscale. Fix this.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Normally the omapdss driver gets the regulators using the regulator
names assigned for omapdss. However, in an effort to get a minimal DSS
support for DT enabled kernel on selected boards, we will add omapdss
devices and platform data the old way even for DT kernel. This causes
the problem that omapdss cannot find the regulators using omapdss's
regulator names.
This patch creates a temporary workaround for DSI and HDMI by trying to
get the regulators also using native OMAP4 regulator names.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This function is now used in the driver init path to handle
probe errors properly. Thus, it may be possible to use this function
outside the exit path.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix sparse warning:
drivers/video/omap2/dss/dispc.c:3320:6: warning: symbol
'dispc_dump_irqs' was not declared. Should it be static?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
Creating the accessory devices, such as audio, from the HDMI driver
allows to regard HDMI as a single entity with audio an display
functionality. This intends to follow the design of drivers such
as MFD, in which a single entity handles the creation of the accessory
devices. Such devices are then used by domain-specific drivers; audio in
this case.
Also, this is in line with the DT implementation of HDMI, in which we will
have a single node to describe this feature of the OMAP SoC.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It could be possible that the DMA port differs accross diferent HDMI IPs. Thus,
add an IP-specific function to obtain the address offset and size of the DMA
data port.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display must be uninitialized in order to free the requested GPIOs.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not blindly assume that the panel could be initialized.
While there, group mutex initialization at a single place.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not assume blindly that the DSS driver was registered successfully.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Minor cleanup to give to the resource variable a more proper name.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merging in Greg's tty tree including a cleanup patch needed by the OMAP serial
header cleanups.
* depends/tty: (305 commits)
tty/serial/8250: Make omap hardware workarounds local to 8250.h
serial/8250/8250_early: Prevent rounding error in uartclk
serial: samsung: use clk_prepare_enable and clk_disable_unprepare
TTY: Report warning when low_latency flag is wrongly used
console: use might_sleep in console_lock
TTY: move tty buffers to tty_port
TTY: add port -> tty link
TTY: tty_buffer, cache pointer to tty->buf
TTY: move TTY_FLUSH* flags to tty_port
TTY: n_tty, propagate n_tty_data
TTY: move ldisc data from tty_struct: locks
TTY: move ldisc data from tty_struct: read_* and echo_* and canon_* stuff
TTY: move ldisc data from tty_struct: bitmaps
TTY: move ldisc data from tty_struct: simple members
TTY: n_tty, add ldisc data to n_tty
TTY: audit, stop accessing tty->icount
TTY: n_tty, remove bogus checks
TTY: n_tty, simplify read_buf+echo_buf allocation
TTY: hci_ldisc, remove invalid check in open
TTY: ldisc, wait for idle ldisc in release
...
check_horiz_timing_omap3() has a variable named 'DS'. i386 uses DS name
for something else, causing a compilation error. As 'DS' is not a very
good local variable name in the first place, let's change it to 'ds',
fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently get the decision whether to use PRCM or DSI PLL clock for
DPI from the board file. This is not a good way to handle it, and it
won't work with device tree.
This patch changes DPI to always use DSI PLL if it's available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The SoCs that have DSI module should have a working DSI PLL. However,
some rare boards have not connected the powers to the DSI PLL.
This patch adds a function that tries to power up the DSI PLL, and
reports if that doesn't succeed. DPI uses this function to fall back to
PRCM clocks if DSI PLL doesn't work.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using dpi_use_dsi_pll() to check if dsi pll is to be used, we
can just check if dpi.dsidev != NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.c currently exposes functions to configure the dispc source clock
and lcd source clock. There are configured separately from the output
drivers.
However, there is no safe way for the output drivers to handle dispc
clock, as it's shared between the outputs. Thus, if, say, the DSI driver
sets up DSI PLL and configures both the dispc and lcd clock sources to
that DSI PLL, the resulting dispc clock could be too low for, say, HDMI.
Thus the output drivers should really only be concerned about the lcd
clock, which is what the output drivers actually use. There's lot to do
to clean up the dss clock handling, but this patch takes one step
forward and removes the use of dss_select_dispc_clk_source() from the
output drivers.
After this patch, the output drivers only configure the lcd source
clock. On omap4+ the dispc src clock is never changed from the default
PRCM source. On omap3, where the dispc and lcd clocks are actually the
same, setting the lcd clock source sets the dispc clock source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't currently set the dss fck when starting up. This is not a
problem, as we setup the fck later when configuring the pixel clocks. Or
this is how it was for omap2, for the rest of the omaps this may not be
so.
For DSI, HDMI and also for DPI when using DSI PLL, we don't need to
change the dss fck, and thus it may be left unconfigured. Usually the
dss fck is already setup fine by default, but we can't trust this.
This patch sets the dss fck to maximum at probe time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_calc_clock_rates() was removed earlier as it was not used, but it is
needed for DSI PLL calculations, so this patch adds it back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It looks like on many OMAP versions powers for both HSClk and HSDiv to
be enabled to have a functional HSDiv.
This patch fixes the issue by forcing both powers on.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI PLL and HSDivider can be used to generate the pixel clock for
LCD overlay manager, which then goes to DPI output. On the DPI output
pin the voltage of the signal is shifted from the OMAP's internal
minimal voltage to 1.8V range. The shifting is not instant, and the
higher the clock frequency, the less time there is to shift the signal
to nominal voltage.
If the HSDivider's divider is greater than one and odd, the resulting
pixel clock does not have 50% duty cycle. For example, with a divider of
3, the duty cycle is 33%.
When combining high frequency (in the area of 140MHz+) and non-50% duty
cycle, it has been observed the the shifter does not have enough time to
shift the voltage enough, and this leads to bad signal which is rejected
by monitors.
As a workaround this patch makes the divider calculation skip all odd
dividers when the required pixel clock is over 100MHz. The limit of
100MHz is a guesstimate.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI may use DSI PLL, so it depends on DSI. However, currently DPI driver
is added first, which causes DPI initialization to fail when it tries to
get the DSI PLL.
This patch changes the init order to fix this.
A better solution would be to separate DSI PLL and DSI drivers. They
have dependencies, though, but we could still have DSI PLL as an
independent entity that we could initialize before any of the output
drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The dispc error handler tries to "fix" issues by disabling and enabling
panel. This is problematic, as we're trying to remove the dependency
from omapdss to the omap_dss_devices. It's also racy, and doesn't really
fix anything.
This patch removes the use of omap_dss_device from the error handler,
and just disables and enables the associated overlay manager. This
should produce similar results as the previous solution, without using
dssdev.
However, the error handling is still horrible. But the problem boils
down to one question, to which I don't have a clear answer: what to do
when a HW error happens?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler has a loop inside another loop, and both use
the same loop variable. This is clearly wrong, and this patch makes a
new variable for the inner loop.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current omapfb code goes over all the modes found from the monitors
EDID data, and searches for a mode that is compatible with the DSS
hardware and has the highest x-res.
While this works ok as such, it proves problematic when using DSI PLL
for pixel clock. Calculating DSI PLL dividers is not the fastest of the
operations, and while doing it for one mode is usually ok, doing it for
20 modes is noticable.
Also, the first mode given in the EDID data should be the native mode of
the monitor, and thus also the best mode, so if that can be used, no
need to look further.
This patch changes the code to use the first mode that is compatible
with the DSS hardware.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It seems that using the second EDID block causes more problems than is
of any help. The first mode in the extended block will get
FB_MODE_IS_FIRST set, which will override the first mode from the first
EDID block, thus making the default videomode selection not to work
properly.
This patch removes the use of the extended edid block for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi driver tries to find the given video timings from its static
list of timings, to find the required ID for the mode. The check tries
to find exact match for the pixel clock, among other checks.
with omapfb driver there can be some amount of error in the give pixel
clock, as the pixel clock is converted between Hz and ps, thus the
hdmi's check fails to find the mode.
This patch makes the check more allowing, by rounding the pixel clocks
to nearest MHz.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
This patch makes use of the hdmi_power_[on|off]_core() functions added
in the previous patch. The functions are used when reading EDID or
detecting if a monitor is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
There's currently just one power-on function for HDMI, which enables the
IP and the video output. When reading EDID or detecting if a monitor is
connected, we don't need the video output.
Enabling the video output for these operations is not a big problem in
itself, but the quick enable/disable cycles caused by the operations
seem to cause sync lost errors from time to time. Also, this makes it
possible to read the EDID before the full video path has been set up.
This patch splits the hdmi_power_on into two parts, hdmi_power_on_core
and hdmi_power_on_full. The "full" version does what hdmi_power_on does
currently, and hdmi_power_on_core only enables the core IP. Similar
changes are made for power_off.
Note that these don't allow the HDMI IP to be first enabled, and later
enable the video output, but the HDMI IP will first need to be powered
off before calling the full version. So this is rather limited
implementation, but it fills the needs for reading EDID.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
DISPC irqs need to be handled from the compat layer and also in the
future by the omapdrm. To make this possible, this patchs adds a set of
helper functions, so that the irqs can be managed without direct
register reads/writes.
The following functions are added, and all the current direct reg
reads/writes are changed to use these.
u32 dispc_read_irqstatus(void);
void dispc_clear_irqstatus(u32 mask);
u32 dispc_read_irqenable(void);
void dispc_write_irqenable(u32 mask);
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new dispc function, dispc_ovl_enabled(). This returns if the overlay
enable bit is set in the registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need a low level manager-enable function for omapdrm. We have that
function as dispc internal func, _enable_mgr_out().
This patch exposes that function, and renames it to dispc_mgr_enable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current dispc_mgr_enable/disable function are blocking, and do a bit
too much for omapdrm. We'll expose new enable & disable functions that
will just set the bits in the registers in the following patches.
This patch renames the current functions to *_sync, to make it clear
that they are blocking, and also to free up the dispc_mgr_enable/disable
names for these new functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use dss_feat_get_num_ovls() in dispc.c instead of
omap_dss_get_num_overlays() to remove the dependency to overlay.c. Note
that we still have uses of omap_dss_get_num_overlays() in dispc.c, but
these will be moved out in the future patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapdss driver sets up the initial connections between
overlays, overlay manager and a panel, based on default display
parameter coming from the board file or via module parameters.
This is unnecessary, as it's the higher level component that should
decide what display to use and how. This patch removes the code from
omapdss, and implements similar code to omapfb.
The def_disp module parameter and the default display platform_data
parameter are kept in omapdss, but omapdss doesn't do anything with
them. It will just return the default display name with
dss_get_default_display_name() call, which omapfb uses. This is done to
keep the backward compatibility.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Export dss_get_def_display_name() with the name of
omapdss_get_def_display_name() so that omapfb can use it after the next
patch which moves default display handling to omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the missing unlock on the error handling path in function
hdmi_dump_regs().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 185bae1095 ("OMAPDSS: DSS: Cleanup
cpu_is_xxxx checks") broke the DSS clocks configuration by erroneously
using the clock parameters applicable to all other OMAP34xx SoCs for the
OMAP363x. This went unnoticed probably because the cpu_is_omap34xx()
class check wasn't seen as matching the OMAP363x subclass.
Fix it by checking for the OMAP363x subclass before checking for the
OMAP34xx class.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.
drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'
Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If dsi_get_dsidev_from_id() is called with a DSI module id that does not
exist on the board, the function will crash as omap_dss_get_output()
will return NULL.
This happens on omap3 boards when dumping DSI clocks, as the dumping
code will try to get the dsidev for DSI modules 0 and 1, but omap3 only
has DSI module 0.
Also clean up the id -> output mapping, so that if the function is
called with invalid module ID it will return NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Archit Taneja <archit@ti.com>
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HUTj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-signed' into omap-for-v3.8/cleanup-headers-serial-take2
This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
dispc_mgr_lclk_rate() cannot currently be called with DIGIT channel
parameter, even if dispc_ovl_lclk_rate() can. Fix this by making
dispc_mgr_lclk_rate() handle DIGIT channel also.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.h contains dispc_irq_handler declaration, even if the function is
dispc.c internal. Remove the declaration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The output drivers get the omapdss hw version from the platform data for
their respective output device. This doesn't work with DT, as there's no
platform data for them.
Add a new function, omapdss_get_version(), which returns the dss version
from the core device, which will have platform data on DT also. The
function is exported so that users of omapdss can also use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The panel drivers contain enable, disable, suspend and resume calls.
The suspend and resume are effectively identical to disable and enable.
This patch removes panel suspend and enable code from omapdss and the
panel drivers, and replaces their use with enable and disable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the missing unlock on the error handling path in function
hdmi_dump_regs().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently have a single function to enable and disable the manager
output for LCD and DIGIT. The functions are a bit complex, as handling
both enable and disable require some extra steps to ensure that the
output is enabled or disabled properly without errors before exiting the
function.
The code can be made simpler to understand by splitting the functions
into separate enable and disable functions. We'll also clean up the
comments and some parameter names at the same time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc.c's functions to enable LCD and DIGIT outputs can be cleaned up a
bit by using common functions to set the enable bit and to check if the
output is enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_setup() uses struct omap_overlay to get the caps for the
overlay. We can change the code to get the caps directly from dss
features, thus removing the dependency to struct omap_overlay.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_set_device and dss_mgr_unset_device are declared in dss.h, but
the functions do not exist. Remove the declarations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dispc has a bunch of functions used to configure output related
parameters:
- dispc_mgr_set_io_pad_mode
- dispc_mgr_enable_stallmode
- dispc_mgr_enable_fifohandcheck
- dispc_mgr_set_clock_div
- dispc_mgr_set_tft_data_lines
- dispc_lcd_enable_signal_polarity
- dispc_mgr_set_lcd_type_tft
These are all called together, and the configuration values are taken
from struct dss_lcd_mgr_config.
Instead of exposing those individual dispc functions, create a new one,
dispc_mgr_set_lcd_config(), which is used to configure the above
parameters from values in struct dss_lcd_mgr_config.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When we enable an output we don't check if we need to register the vsync
isr. This causes us to miss vsync interrupts until somebody changes the
configuration of an overlay or an overlay manager.
Add the registration to dss_mgr_enable to fix the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If dsi_get_dsidev_from_id() is called with a DSI module id that does not
exist on the board, the function will crash as omap_dss_get_output()
will return NULL.
This happens on omap3 boards when dumping DSI clocks, as the dumping
code will try to get the dsidev for DSI modules 0 and 1, but omap3 only
has DSI module 0.
Also clean up the id -> output mapping, so that if the function is
called with invalid module ID it will return NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Archit Taneja <archit@ti.com>
