This patch adds basic support for the PF. With this it is possible to
bring up the interface, but without being able to configure any of the
filters on the interface itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the mailbox that connects the PF to the Switch
Management entity. This mailbox will pass TLV formatted messages between
the two entities by using a pair of shared ring buffers.
The primary use of the mailbox is to configure L2 forwarding addresses,
VLANs, and general resource allocation from the switch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds generic mailbox support. The general idea of the mailboxes
is to use a pair of ring buffers, one for request, one for response to send
data between the local driver and some remote entity be it the PF of the
Switch Manager.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic read/write operations for accessing the hardware.
In addition to read read functionality the read functions also provide
surprise remove detection in the event that the device either loses power
or is removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the TVL message formats supported by the PF,
VF, and Switch Management entity.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic defines and structures needed by the PF for
operation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the beginning framework onto which I am going to add the
fm10k driver which supports the Intel(R) FM10000 Ethernet Switch Host
Interface.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 9cb0e39423.
It causes my Sony Vaio Pro 11 to immediately reboot at startup.
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pcie_poll_cmd() take msecs instead of jiffies, so convert timeout to msecs.
Fixes: 40b960831c ("PCI: pciehp: Compute timeout from hotplug command start time")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull networking fixes from David Miller:
1) If the user gives us a msg_namelen of 0, don't try to interpret
anything pointed to by msg_name. From Ani Sinha.
2) Fix some bnx2i/bnx2fc randconfig compilation errors.
The gist of the issue is that we firstly have drivers that span both
SCSI and networking. And at the top of that chain of dependencies
we have things like SCSI_FC_ATTRS and SCSI_NETLINK which are
selected.
But since select is a sledgehammer and ignores dependencies,
everything to select's SCSI_FC_ATTRS and/or SCSI_NETLINK has to also
explicitly select their dependencies and so on and so forth.
Generally speaking 'select' is supposed to only be used for child
nodes, those which have no dependencies of their own. And this
whole chain of dependencies in the scsi layer violates that rather
strongly.
So just make SCSI_NETLINK depend upon it's dependencies, and so on
and so forth for the things selecting it (either directly or
indirectly).
From Anish Bhatt and Randy Dunlap.
3) Fix generation of blackhole routes in IPSEC, from Steffen Klassert.
4) Actually notice netdev feature changes in rtl_open() code, from
Hayes Wang.
5) Fix divide by zero in bond enslaving, from Nikolay Aleksandrov.
6) Missing memory barrier in sunvnet driver, from David Stevens.
7) Don't leave anycast addresses around when ipv6 interface is
destroyed, from Sabrina Dubroca.
8) Don't call efx_{arch}_filter_sync_rx_mode before addr_list_lock is
initialized in SFC driver, from Edward Cree.
9) Fix missing DMA error checking in 3c59x, from Neal Horman.
10) Openvswitch doesn't emit OVS_FLOW_CMD_NEW notifications accidently,
fix from Samuel Gauthier.
11) pch_gbe needs to select NET_PTP_CLASSIFY otherwise we can get a
build error.
12) Fix macvlan regression wherein we stopped emitting
broadcast/multicast frames over software devices. From Nicolas
Dichtel.
13) Fix infiniband bug due to unintended overflow of skb->cb[], from
Eric Dumazet. And add an assertion so this doesn't happen again.
14) dm9000_parse_dt() should return error pointers, not NULL. From
Tobias Klauser.
15) IP tunneling code uses this_cpu_ptr() in preemptible contexts, fix
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
net: bcmgenet: call bcmgenet_dma_teardown in bcmgenet_fini_dma
net: bcmgenet: fix TX reclaim accounting for fragments
ipv4: do not use this_cpu_ptr() in preemptible context
dm9000: Return an ERR_PTR() in all error conditions of dm9000_parse_dt()
r8169: fix an if condition
r8152: disable ALDPS
ipoib: validate struct ipoib_cb size
net: sched: shrink struct qdisc_skb_cb to 28 bytes
tg3: Work around HW/FW limitations with vlan encapsulated frames
macvlan: allow to enqueue broadcast pkt on virtual device
pch_gbe: 'select' NET_PTP_CLASSIFY.
scsi: Use 'depends' with LIBFC instead of 'select'.
openvswitch: restore OVS_FLOW_CMD_NEW notifications
genetlink: add function genl_has_listeners()
lib: rhashtable: remove second linux/log2.h inclusion
net: allow macvlans to move to net namespace
3c59x: Fix bad offset spec in skb_frag_dma_map
3c59x: Add dma error checking and recovery
sparc: bpf_jit: fix support for ldx/stx mem and SKF_AD_VLAN_TAG
can: at91_can: add missing prepare and unprepare of the clock
...
The fixes for TI DRA7 remove divide-by-zero errors. The recently merged
AT91 clock driver fixes some bad error checking and the QCOM driver fix
restores audio for that platform, a clear regression. A list iteration
bug in the framework core was hit recently and is fixed up here. Finally
a compilation warning is fixed for efm32gg, which is also a regression
fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=dUkX
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock layer fixes from Mike Turquette:
"The fixes for the clock tree are mostly run-time bugs in clock
drivers.
The fixes for TI DRA7 remove divide-by-zero errors. The recently
merged AT91 clock driver fixes some bad error checking and the QCOM
driver fix restores audio for that platform, a clear regression. A
list iteration bug in the framework core was hit recently and is fixed
up here. Finally a compilation warning is fixed for efm32gg, which is
also a regression fix"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk/efm32gg: fix dt init prototype
clk: prevent erronous parsing of children during rate change
clk: rockchip: Fix the clocks for i2c1 and i2c2
clk: qcom: Fix sdc 144kHz frequency entry
clk: at91: fix num_parents test in at91sam9260 slow clk implementation
clk: ti: dra7-atl: Provide error check for incoming parameters in set_rate
clk: ti: divider: Provide error check for incoming parameters in set_rate
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ojl4
-----END PGP SIGNATURE-----
Merge tag 'fscache-fixes-20140917' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull fs-cache fixes from David Howells:
- Put a timeout in releasepage() to deal with a recursive hang between
the memory allocator, writeback, ext4 and fscache under memory
pressure.
- Fix a pair of refcount bugs in the fscache error handling.
- Remove a couple of unused pagevecs.
- The cachefiles requirement that the base directory support rename
should permit rename2 as an alternative - otherwise certain
filesystems cannot now be used as backing stores (such as ext4).
* tag 'fscache-fixes-20140917' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
CacheFiles: Handle rename2
cachefiles: remove two unused pagevecs.
FS-Cache: refcount becomes corrupt under vma pressure.
FS-Cache: Reduce cookie ref count if submit fails.
FS-Cache: Timeout for releasepage()
Florian Fainelli says:
====================
net: bcmgenet: TX reclaim and DMA fixes
This patch set contains one fix for an accounting problem while reclaiming
transmitted buffers having fragments, and the second fix is to make sure
that the DMA shutdown is properly controlled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be manipulaging the DMA_CTRL registers directly by writing
0 to them to disable DMA. This is an operation that needs to be timed to
make sure the DMA engines have been properly stopped since their state
machine stops on a packet boundary, not immediately.
Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to
ensure a proper DMA engine state. As a result, we need to reorder the
function bodies to resolve the use dependency.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET driver supports SKB fragments, and succeeds in transmitting
them properly, but when reclaiming these transmitted fragments, we will
only update the count of free buffer descriptors by 1, even for SKBs
with fragments. This leads to the networking stack thinking it has more
room than the hardware has when pushing new SKBs, and backing off
consequently because we return NETDEV_TX_BUSY.
Fix this by accounting for the SKB nr_frags plus one (itself) and update
ring->free_bds accordingly with that value for each iteration loop in
__bcmgenet_tx_reclaim().
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this_cpu_ptr() in preemptible context is generally bad
Sep 22 05:05:55 br kernel: [ 94.608310] BUG: using smp_processor_id()
in
preemptible [00000000] code: ip/2261
Sep 22 05:05:55 br kernel: [ 94.608316] caller is
tunnel_dst_set.isra.28+0x20/0x60 [ip_tunnel]
Sep 22 05:05:55 br kernel: [ 94.608319] CPU: 3 PID: 2261 Comm: ip Not
tainted
3.17.0-rc5 #82
We can simply use raw_cpu_ptr(), as preemption is safe in these
contexts.
Should fix https://bugzilla.kernel.org/show_bug.cgi?id=84991
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Joe <joe9mail@gmail.com>
Fixes: 9a4aa9af44 ("ipv4: Use percpu Cache route in IP tunnels")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using an atomic bitop on the vgic_v2.vgic_elrsr field which was
not aligned to the natural size on 64-bit platforms. This bug showed up
after QEMU correctly identifies the pl011 line as being level-triggered,
and not edge-triggered.
These data structures are protected by a spinlock so simply use a
non-atomic version of the accessor instead.
Tested-by: Joel Schopp <joel.schopp@amd.com>
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
$ grep CONFIG_CLS_U32_MARK .config
# CONFIG_CLS_U32_MARK is not set
net/sched/cls_u32.c: In function 'u32_change':
net/sched/cls_u32.c:852:1: warning: label 'errout' defined but not used
[-Wunused-label]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2da78092 changed the locking from a mutex to a spinlock,
so we now longer sleep in this context. But there was a leftover
might_sleep() in there, which now triggers since we do the final
free from an RCU callback. Get rid of it.
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Steffen Klassert says:
====================
pull request (net): ipsec 2014-09-22
We generate a blackhole or queueing route if a packet
matches an IPsec policy but a state can't be resolved.
Here we assume that dst_output() is called to kill
these packets. Unfortunately this assumption is not
true in all cases, so it is possible that these packets
leave the system without the necessary transformations.
This pull request contains two patches to fix this issue:
1) Fix for blackhole routed packets.
2) Fix for queue routed packets.
Both patches are serious stable candidates.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
icsk_rto is a 32bit field, and icsk_backoff can reach 15 by default,
or more if some sysctl (eg tcp_retries2) are changed.
Better use 64bit to perform icsk_rto << icsk_backoff operations
As Joe Perches suggested, add a helper for this.
Yuchung spotted the tcp_v4_err() case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC2710 (MLDv1), section 3.7. says:
The length of a received MLD message is computed by taking the
IPv6 Payload Length value and subtracting the length of any IPv6
extension headers present between the IPv6 header and the MLD
message. If that length is greater than 24 octets, that indicates
that there are other fields present *beyond* the fields described
above, perhaps belonging to a *future backwards-compatible* version
of MLD. An implementation of the version of MLD specified in this
document *MUST NOT* send an MLD message longer than 24 octets and
MUST ignore anything past the first 24 octets of a received MLD
message.
RFC3810 (MLDv2), section 8.2.1. states for *listeners* regarding
presence of MLDv1 routers:
In order to be compatible with MLDv1 routers, MLDv2 hosts MUST
operate in version 1 compatibility mode. [...] When Host
Compatibility Mode is MLDv2, a host acts using the MLDv2 protocol
on that interface. When Host Compatibility Mode is MLDv1, a host
acts in MLDv1 compatibility mode, using *only* the MLDv1 protocol,
on that interface. [...]
While section 8.3.1. specifies *router* behaviour regarding presence
of MLDv1 routers:
MLDv2 routers may be placed on a network where there is at least
one MLDv1 router. The following requirements apply:
If an MLDv1 router is present on the link, the Querier MUST use
the *lowest* version of MLD present on the network. This must be
administratively assured. Routers that desire to be compatible
with MLDv1 MUST have a configuration option to act in MLDv1 mode;
if an MLDv1 router is present on the link, the system administrator
must explicitly configure all MLDv2 routers to act in MLDv1 mode.
When in MLDv1 mode, the Querier MUST send periodic General Queries
truncated at the Multicast Address field (i.e., 24 bytes long),
and SHOULD also warn about receiving an MLDv2 Query (such warnings
must be rate-limited). The Querier MUST also fill in the Maximum
Response Delay in the Maximum Response Code field, i.e., the
exponential algorithm described in section 5.1.3. is not used. [...]
That means that we should not get queries from different versions of
MLD. When there's a MLDv1 router present, MLDv2 enforces truncation
and MRC == MRD (both fields are overlapping within the 24 octet range).
Section 8.3.2. specifies behaviour in the presence of MLDv1 multicast
address *listeners*:
MLDv2 routers may be placed on a network where there are hosts
that have not yet been upgraded to MLDv2. In order to be compatible
with MLDv1 hosts, MLDv2 routers MUST operate in version 1 compatibility
mode. MLDv2 routers keep a compatibility mode per multicast address
record. The compatibility mode of a multicast address is determined
from the Multicast Address Compatibility Mode variable, which can be
in one of the two following states: MLDv1 or MLDv2.
The Multicast Address Compatibility Mode of a multicast address
record is set to MLDv1 whenever an MLDv1 Multicast Listener Report is
*received* for that multicast address. At the same time, the Older
Version Host Present timer for the multicast address is set to Older
Version Host Present Timeout seconds. The timer is re-set whenever a
new MLDv1 Report is received for that multicast address. If the Older
Version Host Present timer expires, the router switches back to
Multicast Address Compatibility Mode of MLDv2 for that multicast
address. [...]
That means, what can happen is the following scenario, that hosts can
act in MLDv1 compatibility mode when they previously have received an
MLDv1 query (or, simply operate in MLDv1 mode-only); and at the same
time, an MLDv2 router could start up and transmits MLDv2 startup query
messages while being unaware of the current operational mode.
Given RFC2710, section 3.7 we would need to answer to that with an MLDv1
listener report, so that the router according to RFC3810, section 8.3.2.
would receive that and internally switch to MLDv1 compatibility as well.
Right now, I believe since the initial implementation of MLDv2, Linux
hosts would just silently drop such MLDv2 queries instead of replying
with an MLDv1 listener report, which would prevent a MLDv2 router going
into fallback mode (until it receives other MLDv1 queries).
Since the mapping of MRC to MRD in exactly such cases can make use of
the exponential algorithm from 5.1.3, we cannot [strictly speaking] be
aware in MLDv1 of the encoding in MRC, it seems also not mentioned by
the RFC. Since encodings are the same up to 32767, assume in such a
situation this value as a hard upper limit we would clamp. We have asked
one of the RFC authors on that regard, and he mentioned that there seem
not to be any implementations that make use of that exponential algorithm
on startup messages. In any case, this patch fixes this MLD
interoperability issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
old gcc 4.2 used by avr32 architecture produces warnings:
lib/test_bpf.c:1741: warning: integer constant is too large for 'long' type
lib/test_bpf.c:1741: warning: integer constant is too large for 'long' type
lib/test_bpf.c: In function '__run_one':
lib/test_bpf.c:1897: warning: 'ret' may be used uninitialized in this function
silence these warnings.
Fixes: 02ab695bb3 ("net: filter: add "load 64-bit immediate" eBPF instruction")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one error condition dm9000_parse_dt() returns NULL, however the
return value is checked using IS_ERR() in dm9000_probe(), leading to the
error not being properly propagated if CONFIG_OF is not enabled or the
device tree data is not available. Fix this by also returning an
ERR_PTR() in this case.
Fixes: 0b8bf1baab (net: dm9000: Allow instantiation using device tree)
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ah struct might not have been initialized when
interrupt comes so check for it.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clock is disabled when the device is blocked.
So, clock_enabled is the logical negation of "blocked".
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes to the cls_u32 classifier must appear atomic to the
readers. Before this patch if a change is requested for both
the exts and ifindex, first the ifindex is updated then the
exts with tcf_exts_change(). This opens a small window where
a reader can have a exts chain with an incorrect ifindex. This
violates the the RCU semantics.
Here we resolve this by always passing u32_set_parms() a copy
of the tc_u_knode to work on and then inserting it into the hash
table after the updates have been successfully applied.
Tested with the following short script:
#tc filter add dev p3p2 parent 8001:0 protocol ip prio 99 handle 1: \
u32 divisor 256
#tc filter add dev p3p2 parent 8001:0 protocol ip prio 99 \
u32 link 1: hashkey mask ffffff00 at 12 \
match ip src 192.168.8.0/2
#tc filter add dev p3p2 parent 8001:0 protocol ip prio 102 \
handle 1::10 u32 classid 1:2 ht 1: \
match ip src 192.168.8.0/8 match ip tos 0x0a 1e
#tc filter change dev p3p2 parent 8001:0 protocol ip prio 102 \
handle 1::10 u32 classid 1:2 ht 1: \
match ip src 1.1.0.0/8 match ip tos 0x0b 1e
CC: Eric Dumazet <edumazet@google.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a missed free_percpu in the unwind code path and when
keys are destroyed.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have 3 NFC fixes for 3.17:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZLhy
-----END PGP SIGNATURE-----
Merge tag 'nfc-fixes-3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.17 fixes
We have 3 NFC fixes for 3.17:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the slave is the curr_active_slave, no need to check
whether the slave is active or not, it is always active.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an extra semi-colon so __rtl8169_set_features() is called every
time.
Fixes: 929a031dfd ('r8169: adjust __rtl8169_set_features')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
Unable to load various tunneling modules without this:
[ 80.679049] fou: Unknown symbol udp_sock_create6 (err 0)
[ 91.439939] ip6_udp_tunnel: Unknown symbol ip6_local_out (err 0)
[ 91.439954] ip6_udp_tunnel: Unknown symbol __put_net (err 0)
[ 91.457792] vxlan: Unknown symbol udp_sock_create6 (err 0)
[ 91.457831] vxlan: Unknown symbol udp_tunnel6_xmit_skb (err 0)
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
Patches 1 and 2 fix sparse warnings (static declaration needed and endian
declaration needed) introduced by the earlier patch set.
Patches 3 and 4 add 20G/40G speed reporting via ethtool for the Skyhawk-R
chip.
Patches 5 to 12 fix various style issues and checkpatch warnings in the
driver such as:
- removing unnecessary return statements in void routines
- adding needed blank lines after a declaration block
- deleting multiple blank lines
- inserting a blank line after a function/struct definition
- removing space after typecast
- fixing multiple assignments on a single line
- fixing alignment on a line wrap
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes alignment whereever it doesn't match the open parenthesis
alignment.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes multiple assignments on a single line as warned
by checkpatch.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary spaces after typecasts as per checkpatch warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes checkpatch warnings about blank lines after an open brace '{'.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch inserts a blank line after function/struct/union/enum definitions
as per checkpatch warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes multiple blank lines in the driver as per checkpatch
warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes checkpatch warnings in be2net by adding a blank line
between declaration and code blocks.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds speed reporting via ethtool for 20G KR2 interface on the
Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds speed reporting via ethtool for 40Gbps KR4 interface
on the Skyhawk-R chip.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a sprase warnings regarding endian declarations introduced
by the following commit:
fixes: e36edd9 ("be2net: add ethtool "-m" option support")
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a sparse warning about missing static declaration that was
introduced by the following commit:
fixes: 936767039c ("be2net: send a max of 8 EQs to be_cmd_modify_eqd() on Lancer")
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nnB5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Two very simple bugfixes, affecting all supported architectures"
[ Two? There's three commits in here. Oh well, I guess Paolo didn't
count the preparatory symbol export ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: correct null pid check in kvm_vcpu_yield_to()
KVM: check for !is_zero_pfn() in kvm_is_mmio_pfn()
mm: export symbol dependencies of is_zero_pfn()
Commit ce93718fb7 ("net: Don't keep
around original SKB when we software segment GSO frames") frees the
original skb after software GSO even for dodgy gso skbs. This breaks
the stream throughput from untrusted sources, since only header
checking was done during software GSO instead of a true
segmentation. This patch fixes this by freeing the original gso skb
only when it was really segmented by software.
Fixes ce93718fb7 ("net: Don't keep
around original SKB when we software segment GSO frames.")
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw is in ALDPS mode, the hw may have no response for accessing
the most registers. Therefore, the ALDPS should be disabled before
accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
wouldn't enter ALDPS mode when linking on. The hw would enter the
ALDPS mode after several seconds when link down occurs and the ALDPS
is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have extra identation before .skb_copy_to_linear_data_offset(),
this patch just remove the identation.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
