Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pointer comparison is not sufficient for non-NULL device name matching,
so use strcmp(). Otherwise the semantics remain the same.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When one regulator supplies another allow the relationship to be specified
using names rather than struct regulators, in a similar manner to that
allowed for consumer supplies. This allows static configuration at compile
time, reducing the need for dynamic init code.
Also change the references to LINE supply to be system supply since line
is sometimes used for actual supplies and therefore potentially confusing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the request for wdt_mem region fails, this patch modifies the driver
such that, it does not try to release the wdt_mem region on exit.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds HAVE_S3C2410_WATCHDOG to control inclusion of watchdog driver
for Samsung SoCs. This option will help to include the driver only for the
necessary machines and not for all for any given arch.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For TCO V1 devices the programmed timeout was twice too long
because the fact that the TCO V1 timer needs to count down
twice before triggering the watchdog, wasn't accounted for.
Also the timeout values in the module description and error
message were clarified. And the _STS registers are 16 bit
instead of 8 bit.
Signed-off-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Simon Kagstrom <simon.kagstrom@netinsight.se>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If we are not able to register then it is better to have
watchdog in disabled state than noticing a system reboot.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-By: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Move the limited watchdog driver help from kernel-parameters.txt
to Documentation/watchdog/watchdog-parameters.txt and add info to it
for all watchdog drivers except the ones that have driver-specific
files already.
Correct minor comments and MODULE_PARM_DESC() text in 2 places.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix MODULE_PARM_DESC() strings in several watchdog drivers.
Some are simple as add a parenthesis.
Others are problems from __stringify() being used on a
variable name instead of a macro name, so the variable name
is produced in the string instead of its build-time value.
In these cases, create a macro for the value so that the
module param description string is useful.
Only pc87413_wdt has been built (due to toolchains).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Module roccat is a char device used to report special events of roccat hardware
to userland. These events include requests for on-screen-display of profile or
dpi settings or requests for execution of macro sequences that are not stored
in device. The information in these events depends on hid device implementation
and contains data that is not available in a single hid event or else hidraw
could have been used.
It is inspired by hidraw, but uses only one circular buffer for all readers.
The device is as generic as possible so that the functionality is usable by all
(kone and upcomming) roccat device drivers.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix sock.h kernel-doc warning:
Warning(include/net/sock.h:1438): No description found for parameter 'wq'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo in cgroup_cls_state when cls_cgroup is built-in.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 58f9b0b024, "of: eliminate
of_device->node and dev_archdata->{of,prom}_node" changed the location
of the device_node pointer. Most drivers were converted to the new
location, but the xilinx_spi_of driver was missed and now fails to
compile.
This patch fixes up the xilinx_spi_of driver to use the new location.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
BugLink: https://launchpad.net/bugs/576160
Symptom: Currently (2.6.32.12) the Dell M1730 uses the 3stack model
quirk. Unfortunately this means that capture is not functional out-
of-the-box despite ensuring that capture settings are unmuted and
raised fully.
Test case: boot from Ubuntu 10.04 LTS live cd; capture does not
work.
Resolution: Correct the model quirk for Dell M1730 to rely on the
BIOS configuration.
This patch also trivially sorts the quirk into the correct section
based on the comments.
Reported-and-Tested-By: <picdragon99@msn.com>
Tested-By: Daren Hayward
Tested-By: Tobias Krais
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
First issue:
With the original patch, I've noticed by unmuting the mic
(and even having it muted), there is a distorted("Noise")
coming from the internal speakers, even when the headphones are plugged in.
What my finding's revealed is:
/* Mic (rear) pin: input vref at 80% */
{0x18, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
{0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
From the original patch. Looking at codec#0 0x18/0x1a is listed as:
Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x90100141: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0x4, Sequence = 0x1
Misc = NO_PRESENCE
Pin-ctls: 0x41: OUT VREF_50
Unsolicited: tag=00, enabled=0
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
seems this Node is listed as: [Fixed] Speaker while 0x15
Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x018b3020: [Jack] Line In at Ext Rear
Conn = Comb, Color = Blue
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x01: VREF_50
Unsolicited: tag=00, enabled=0
Connection: 5
0x0c 0x0d* 0x0e 0x0f 0x26
is [Jack] Line In at Ext Rear.
(looking at the other apple products as examples
I came up with the fix below).
Second issue:
alc885_mbp_4ch_modes
The original patch does a good job with the
HP pin automute function, but from what I noticed is I would have to manually
change the channel form 2 to 4 after plugging the headphones in.
And not to mention having odd moments to where I was jamming out
with the headphones on, then later realized I had sound blasting out
of the speakers as well. My findings revealed that changing
alc885_mbp_4ch_modes to alc885_mba21_ch_modes and setting
- spec->autocfg.speaker_pins[0] = 0x15;
+ spec->autocfg.speaker_pins[0] = 0x18;
gets the automute function when the headphones plugged in working
flawlessly(and the no need to manually change the channel number
afterwards).
Third issue:
alc885_imac91_mixer
There probably doesnt need to be anything changed with this
(esspecially if your one to like lots of sliders),but my findings
revealed that mac osx only has a master on the top right,
another switch on itunes, and then a slider for the mic.
So the changes I did below try and mimic osx as much as possible
(only thing I had an issue with is just having one mute switch
on the master, instead of having two(still investigating)).
fourth issue:
alc882_capture_source
I endeded up creating alc889A_imac91_capture_source()
only because looking at alc882_capture_source I see
that the mic is set to 0x1 while this works, I also noticed
that adding 0x1 and 0x01 and testing that 0x1 somehow
stops working, and 0x01 works(so I figured 0x01 was more
of the alpha of the numbers(still need to figure out
where that valuse is)). In any case the microphone
does work with the original, and with the below patch, but both
still record not as clean(lots of "Noise", which I would like to
look into too).
Note: using alsamixer -Va reveals the capture switches.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/549560
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile)
Resolution: add SSID for Toshiba A100-259 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
This patch also trivially sorts the quirk table in ascending order by
subsystem vendor.
Reported-and-Tested-by: <davide.molteni@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/583983
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile).
Resolution: add SSID for Acer Aspire 5110 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
Reported-and-Tested-By: Leo
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the VENDOR/DEVICE ids provided in pci_ids.h instead of creating
local ids of the same values.
Also, fix the following checkpatch.pl warnings:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
WARNING: unnecessary whitespace before a quoted newline
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Computation of the clock prescaler value returned bogus results if
the requested SPI clock was impossible to set. It now sets either
the maximum or minimum clock frequency, as appropriate.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A number of files in drivers/spi fail checkincludes.pl due to the double
include of <linux/spi/spi_bitbang.h>.
The first include is needed to get the struct spi_bitbang definition and
the spi_bitbang_* function prototypes.
The second include happens after defining EXPAND_BITBANG_TXRX to get the
inlined bitbang_txrx_* utility functions.
The <linux/spi/spi_bitbang.h> header is also included by a number of other
spi drivers, as well as some arch/ code, in order to use struct spi_bitbang
and the associated functions.
To fix the double include, and remove any potential confusion about it, move
the inlined bitbang_txrx_* functions to a new private header in drivers/spi
and also remove the need to define EXPAND_BITBANG_TXRX.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since PSC could also be used in other modes than UART mode
we move PSC FIFO memory initialization from serial driver to
common platform code. The initialized FIFO memory slices may
not overlap, so the most easy way would be to configure them
all at once at init time for all PSC devices. This is now done
by this patch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds an SPI master driver for the Cirrus EP93xx SPI controller found
in EP93xx chips.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix this warning:
Documentation/spi/spidev_fdx.c: In function `do_msg':
Documentation/spi/spidev_fdx.c:61: warning: cast from pointer to integer of different size
Documentation/spi/spidev_fdx.c:64: warning: cast from pointer to integer of different size
buf should be unsigned long to match native arch on 32-bit x86 compile.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Turbo mode allows to read data to shift register when rx-buffer
is full thus improving the perfomance. This feature is available
for RX-only mode.
In PIO turbo mode when the penultimate word is available
in RX-buffer the controller should be disabled before reading data
to prevent the next transaction triggering. The controller itself
handles the last word to be correctly loaded to shift-register and
then transferred to RX-buffer.
The turbo mode is enabled by setting turbo_mode parameter to 1.
This parameter is a part of omap2_mcspi_device_config structure
which is passed through the spi_device controller_data pointer.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The value 160 has been obtained as optimal in testing it for
wl1271 which use spi for communication.
In some sense this change might also influence on other spi devices
connected to omap2_mcspi controller.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fix prevents queue being marked as "stopped", if data exists
in the queue list.
Signed-off-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Signed-off-by: Lukasz Baj <lukasz.baj@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds support for a further ST variant of the PL022 called
PL023. Some differences in the control registers due to being
stripped down to SPI mode only, and a new clock feedback sample
delay config setting is available.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The PL022 SPI driver did not cleanly separate between the
original unmodified ARM version and the ST Microelectronics
versions. Split this more cleanly and fix some whitespace
moaning from checkpatch at the same time.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes a typo were map_tx_dma is used instead of
map_rx_dma, casing the driver to unmap rx_dma when it
shouldn't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
QE mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for words
> 8 bits. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also move the different quirks into its own function to keep
mpc8xxx_spi_setup_transfer() sane.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Under abnormal termination, modify_qp() closes the QP, and async event
(AE) handling also attempts to close the same QP, causing a crash.
Fix this by checking the state of the QP before processing the AE.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enhance ethtool to read hardware registers for rcv/tx error stats.
Also add support for free pbl resources. Remove cq depth stats, which
are not used.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- wrap cq->cqidx_inc based on cq size.
- optimize t4_arm_cq logic.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
1) save the timestamp flit in the cq when we consume a CQE.
2) always compare the saved flit with the previous entry flit when
reading the next CQE entry. If the flits don't compare, then we
have overflowed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need 1 extra entry for the status page and 1 to always have 1 free
entry to detect when the queue is full.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The LLD now supports proper UP state change events, so move the RDMA
provider registration to UP path.
This fixes a crash when loading iw_cxgb4 _after_ the NFS/RDMA
transport is up and running.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the RDMA core unregister path, kernel users will be calling down
into the T4 provider to release resources. So we cannot detach from
the LLD until this process completes.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes possible memory leak.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI function reset needs to invoked after fw init ioctl is issued.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
