with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests
below are off by one. also don't do an '< 0' test on an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8390 driver was structured by Al Viro to allow the flexibility
required by platforms. lib8390.c contains the core code which drivers
explicitly include:
- 8390.c includes lib8390.c to provide the standard ISA based driver.
- etherh.c includes it with the accessors defined for RiscPC platforms,
where it is addressed via the MMIO accessors with a device dependent
register spacing.
Other platform drivers do something similar.
However, b9a9b4b caused the kernel to contain not only the etherh
private build of lib8390 (included in etherh.c) but also lib8390.c
itself, and referred the new net_device_ops methods to the ISA version.
The result of this is is not pretty:
Unable to handle kernel paging request at virtual address 12032030
pgd = c8330000
[12032030] *pgd=00000000
Internal error: Oops: 18331805 [#1]
Modules linked in: ipv6
CPU: 0 Not tainted (2.6.29-rc3 #167)
PC is at do_set_multicast_list+0xd0/0x190
LR is at bitrev32+0x28/0x34
pc : [<c017aab4>] lr : [<c0139120>] psr: a0000093
sp : c8321d9c ip : c8321d84 fp : c8321dbc
r10: c80c6800 r9 : 00000000 r8 : c80c6b60
r7 : c80c6b80 r6 : cc80c800 r5 : c80c6800 r4 : 00000000
r3 : cc80c80c r2 : 00000004 r1 : 00000007 r0 : e0000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
...
Fix up b9a9b4b by making etherh's net_device_ops refer to the internal
lib8390 functions, and remove the build of the ISA 8390.c driver.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Further to a71558d, this is round five of fixes to make etherh work
again. As mainline kernels stand, the fixes in b9a9b4b were the wrong
approach.
The 8390 driver was structured by Al Viro to allow the flexibility required
by platforms. lib8390.c contains the core code which drivers explicitly
include:
- 8390.c includes lib8390.c to provide the standard ISA based driver.
- etherh.c includes it with the accessors defined for RiscPC platforms,
where it is addressed via the MMIO accessors with a device dependent
register spacing.
Other platform drivers do something similar.
However, b9a9b4b caused the kernel to contain not only the etherh private
build of lib8390 (included in etherh.c) but also lib8390.c itself, and
referred the new net_device_ops methods to the ISA version. The result
of this is is not pretty:
Unable to handle kernel paging request at virtual address 12032030
pgd = c8330000
[12032030] *pgd=00000000
Internal error: Oops: 18331805 [#1]
Modules linked in: ipv6
CPU: 0 Not tainted (2.6.29-rc3 #167)
PC is at do_set_multicast_list+0xd0/0x190
LR is at bitrev32+0x28/0x34
pc : [<c017aab4>] lr : [<c0139120>] psr: a0000093
sp : c8321d9c ip : c8321d84 fp : c8321dbc
r10: c80c6800 r9 : 00000000 r8 : c80c6b60
r7 : c80c6b80 r6 : cc80c800 r5 : c80c6800 r4 : 00000000
r3 : cc80c80c r2 : 00000004 r1 : 00000007 r0 : e0000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
...
Fix up b9a9b4b by making etherh's net_device_ops refer to the internal
lib8390 functions, and remove the build of the ISA 8390.c driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Further to 483a2b3a31, also fix:
drivers/net/arm/etherh.c:649: error: 'eth_set_mac_addr' undeclared here (not in a function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
spin_lock functions take a pointer to the lock, not the lock itself.
This error was noticed by compiling ebsa110_defconfig for linux-rt where
the locking functions obviously are more picky about their arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Roel Kluin <12o3l@tiscali.nl>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Russell King:
drivers/net/arm/etherh.c:649: error: unknown field 'ndo_set_mac_addr' specified in initializer
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices were converted incorrectly and are missing the validate
address hooks.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicated include in drivers/net/arm/ks8695net.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I hit similar build failure due to the change in the netif_rx_reschedule()
drivers/net/ehea/ehea_main.c: In function 'ehea_poll':
drivers/net/ehea/ehea_main.c:844: warning: passing argument 1 of 'netif_rx_reschedule' from incompatible pointer type
drivers/net/ehea/ehea_main.c:844: error: too many arguments to function 'netif_rx_reschedule'
make[3]: *** [drivers/net/ehea/ehea_main.o] Error 1
greping through the sources for the changes missed out, we have
./drivers/net/arm/ixp4xx_eth.c:507: netif_rx_reschedule(dev, napi)) {
./drivers/net/arm/ep93xx_eth.c:310: if (more && netif_rx_reschedule(dev, napi))
./drivers/net/wan/ixp4xx_hss.c:657: netif_rx_reschedule(dev, napi)) {
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the KS8695 ethernet device (ks8695net).
This driver is only of use on the KS8695 which is an ARM9 based SoC. The
documentation on this SoC is sparse and poor, with barely a register
description and a rough outline of how the ethernet works, this driver was
therefore written with strong reference to the Micrel supplied Linux 2.6.9
port, and to Andrew Victor's ks8695eth driver.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Acked-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build of ARM etherh driver with new net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arm ixp4xx_eth driver doesn't compile in 2.6.27-rc1:
CC [M] drivers/net/arm/ixp4xx_eth.o
drivers/net/arm/ixp4xx_eth.c: In function 'eth_poll':
drivers/net/arm/ixp4xx_eth.c:554: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:554: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'eth_xmit':
drivers/net/arm/ixp4xx_eth.c:701: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:701: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'init_queues':
drivers/net/arm/ixp4xx_eth.c:886: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:886: error: too few arguments to function 'dma_mapping_error'
make[3]: *** [drivers/net/arm/ixp4xx_eth.o] Error 1
make[2]: *** [drivers/net/arm] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
dma_mapping_error() changed in 2.6.27-rc1 to also take a device parameter,
but nobody bothered updating ixp4xx_eth.c. Fixed by passing the appropriate
device value in the dma_mapping_error() calls.
Tested on an ixp425 box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
ipw2200: Call netif_*_queue() interfaces properly.
netxen: Needs to include linux/vmalloc.h
[netdrvr] atl1d: fix !CONFIG_PM build
r6040: rework init_one error handling
r6040: bump release number to 0.18
r6040: handle RX fifo full and no descriptor interrupts
r6040: change the default waiting time
r6040: use definitions for magic values in descriptor status
r6040: completely rework the RX path
r6040: call napi_disable when puting down the interface and set lp->dev accordingly.
mv643xx_eth: fix NETPOLL build
r6040: rework the RX buffers allocation routine
r6040: fix scheduling while atomic in r6040_tx_timeout
r6040: fix null pointer access and tx timeouts
r6040: prefix all functions with r6040
rndis_host: support WM6 devices as modems
at91_ether: use netstats in net_device structure
sfc: Create one RX queue and interrupt per CPU package by default
sfc: Use a separate workqueue for resets
sfc: I2C adapter initialisation fixes
...
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
