Add module parameter to control logging levels of async event
notifications from firmware that get logged to system log. Also, allow
changing the value from sysfs after driver load.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Load balancing IO completions across all available MSI-X vectors should be
enabled for Invader and later generation controllers only. This needs to
be disabled for older controllers. Add an adapter type check before
setting msix_load_balance flag.
Fixes: 1d15d9098a ("scsi: megaraid_sas: Load balance completions across all MSI-X")
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_get_target_prop(), driver is incorrectly calculating the target
ID for devices with channel 1 and 3. Due to this, firmware will either
fail the command (if there is no device with the target id sent from
driver) or could return the properties for a target which was not
intended. Devices could end up with the wrong queue depth due to this.
Fix target id calculation for channel 1 and 3.
Fixes: 96188a89cc ("scsi: megaraid_sas: NVME interface target prop added")
Cc: stable@vger.kernel.org
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_debug_dump_all_queues() function repeatedly calls into
lpfc_debug_dump_qe() which has a temporary 128 byte buffer. This was fine
before the introduction of CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE because
each instance could occupy the same stack slot. However, now they each get
their own copy, which leads to a huge increase in stack usage as seen from
the compiler warning:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debug_dump_all_queues':
drivers/scsi/lpfc/lpfc_debugfs.c:6474:1: error: the frame size of 1712 bytes is larger than 100 bytes [-Werror=frame-larger-than=]
Avoid this by not marking lpfc_debug_dump_qe() as inline so the compiler
can choose to emit a static version of this function when it's needed or
otherwise silently drop it. As an added benefit, not inlining multiple
copies of this function means we save several kilobytes of .text section,
reducing the file size from 47kb to 43.
It is somewhat unusual to have a function that is static but not inline in
a header file, but this does not cause problems here because it is only
used by other inline functions. It would however seem reasonable to move
all the lpfc_debug_dump_* functions into lpfc_debugfs.c and not mark them
inline as a later cleanup.
Fixes: 81a56f6dcd ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, all USB devices skip VPD pages, even when the device supports
them (SPC-3 and later), but some of them support VPD, like Cruzer Blade.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function sas_wait_eh is declared static and marked EXPORT_SYMBOL, which
is at best an odd combination. Because the function is not used outside of
the drivers/scsi/libsas/sas_scsi_host.c file it is defined in, this commit
removes the EXPORT_SYMBOL() marking.
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/megaraid/megaraid_sas_base.c:271:1: warning: symbol 'megasas_issue_dcmd' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_base.c:2227:6: warning: symbol 'megasas_do_ocr' was not declared. Should it be static?
drivers/scsi/megaraid/megaraid_sas_base.c:3194:25: warning: symbol 'megaraid_host_attrs' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With a possibly faulty disk the following messages may appear in the logs:
kernel: sd 0:0:9:0: timing out command, waited 180s
kernel: sd 0:0:9:0: timing out command, waited 20s
kernel: sd 0:0:9:0: timing out command, waited 20s
kernel: sd 0:0:9:0: timing out command, waited 60s
kernel: sd 0:0:9:0: timing out command, waited 20s
This is not very informative because it's not possible to identify the
command that timed out.
This patch replaces sdev_printk() with scmd_printk().
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On session deletion, current qla code would unregister an NVMe session
before flushing IOs. This patch would move the unregistration of NVMe
session after IO flush. This way FC-NVMe layer would not have to wait for
stuck IOs. In addition, qla2xxx would stop accepting new IOs during session
deletion.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch uses kref to protect access between fcp_abort path and nvme
command and LS command completion path. Stack trace below shows the abort
path is accessing stale memory (nvme_private->sp).
When command kref reaches 0, nvme_private & srb resource will be
disconnected from each other. Any subsequence nvme abort request will not
be able to reference the original srb.
[ 5631.003998] BUG: unable to handle kernel paging request at 00000010000005d8
[ 5631.004016] IP: [<ffffffffc087df92>] qla_nvme_abort_work+0x22/0x100 [qla2xxx]
[ 5631.004086] Workqueue: events qla_nvme_abort_work [qla2xxx]
[ 5631.004097] RIP: 0010:[<ffffffffc087df92>] [<ffffffffc087df92>] qla_nvme_abort_work+0x22/0x100 [qla2xxx]
[ 5631.004109] Call Trace:
[ 5631.004115] [<ffffffffaa4b8174>] ? pwq_dec_nr_in_flight+0x64/0xb0
[ 5631.004117] [<ffffffffaa4b9d4f>] process_one_work+0x17f/0x440
[ 5631.004120] [<ffffffffaa4bade6>] worker_thread+0x126/0x3c0
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffc050d10c>] qla_nvme_unregister_remote_port+0x6c/0xf0 [qla2xxx]
PGD 800000084cf41067 PUD 84d288067 PMD 0
Oops: 0000 [#1] SMP
Call Trace:
[<ffffffff98abcfdf>] process_one_work+0x17f/0x440
[<ffffffff98abdca6>] worker_thread+0x126/0x3c0
[<ffffffff98abdb80>] ? manage_workers.isra.26+0x2a0/0x2a0
[<ffffffff98ac4f81>] kthread+0xd1/0xe0
[<ffffffff98ac4eb0>] ? insert_kthread_work+0x40/0x40
[<ffffffff9918ad37>] ret_from_fork_nospec_begin+0x21/0x21
[<ffffffff98ac4eb0>] ? insert_kthread_work+0x40/0x40
RIP [<ffffffffc050d10c>] qla_nvme_unregister_remote_port+0x6c/0xf0 [qla2xxx]
The crash is due to a bad entry in the nvme_rport_list. This list is not
protected, and when a remoteport_delete callback is called, driver
traverses the list and crashes.
Actually, the list could be removed and driver could traverse the main
fcport list instead. Fix does exactly that.
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Aero adapters, driver provides three different performance modes
controlled through module parameter named 'perf_mode'. Below are those
performance modes:
0: Balanced - Additional high IOPS reply queues will be enabled along with
low latency queues. Interrupt coalescing will be enabled only for these
high IOPS reply queues.
1: IOPS - No additional high IOPS queues are enabled. Interrupt coalescing
will be enabled on all reply queues.
2: Latency - No additional high IOPS queues are enabled. Interrupt
coalescing will be disabled on all reply queues. This is a legacy
behavior similar to Ventura & Invader Series.
Default performance mode settings:
- Performance mode set to 'Balanced', if Aero controller is working in
16GT/s PCIe speed.
- Performance mode will be set to 'Latency' mode for all other cases.
Through module parameter 'perf_mode', user can override default performance
mode to desired one.
Captured some performance numbers with these performance modes. 4k Random
Read IO performance numbers on 24 SAS SSD drives for above three
performance modes. Performance data is from Intel Skylake and HGST SS300
(drive model SDLL1DLR400GCCA1).
IOPS:
-----------------------------------------------------------------------
|perf_mode | qd = 1 | qd = 64 | note |
|-------------|--------|---------|-------------------------------------
|balanced | 259K | 3061k | Provides max performance numbers |
| | | | both on lower QD workload & |
| | | | also on higher QD workload |
|-------------|--------|---------|-------------------------------------
|iops | 220K | 3100k | Provides max performance numbers |
| | | | only on higher QD workload. |
|-------------|--------|---------|-------------------------------------
|latency | 246k | 2226k | Provides good performance numbers |
| | | | only on lower QD worklaod. |
-----------------------------------------------------------------------
Average Latency:
-----------------------------------------------------
|perf_mode | qd = 1 | qd = 64 |
|-------------|--------------|----------------------|
|balanced | 92.05 usec | 501.12 usec |
|-------------|--------------|----------------------|
|iops | 108.40 usec | 498.10 usec |
|-------------|--------------|----------------------|
|latency | 97.10 usec | 689.26 usec |
-----------------------------------------------------
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver will use round-robin method for IO submission in batches within
the high IOPS queues when the number of in-flight ios on the target device
is larger than 8. Otherwise the driver will use low latency reply queues.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
High iops queues are mapped to non-managed IRQs. Set affinity of
non-managed irqs to local numa node. Low latency queues are mapped to
managed IRQs.
Driver reserves some reply queues for high IOPS queues (through
pci_alloc_irq_vectors_affinity and .pre_vectors interface). The rest of
queues are for low latency.
Based on IO workload, driver will decide which group of reply queues
(either high IOPS queues or low latency queues) to be used.
High IOPS queues will be mapped to local numa node of controller and
low latency queues will be mapped to CPUs across numa nodes. In general,
high IOPS and low latency queues should fit into 128 reply queues
which is the max number of reply queues supported by Aero adapters.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver should enable interrupt coalescing (during driver load and after
Controller Reset) for High IOPS queues by masking appropriate bits in IOC
INIT frame.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero controllers support balanced performance mode through the ability to
configure queues with different properties.
Reply queues with interrupt coalescing enabled are called "high iops reply
queues" and reply queues with interrupt coalescing disabled are called "low
latency reply queues".
The driver configures a combination of high iops and low latency reply
queues if:
- HBA is an AERO controller;
- MSI-X vectors supported by the HBA is 128;
- Total CPU count in the system more than high iops queue count;
- Driver is loaded with default max_msix_vectors module parameter; and
- System booted in non-kdump mode.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added driver support to allow passthrough MPI toolbox type MFI commands to
firmware based on firmware capability.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For RAID5/RAID6 volumes configured behind Aero, driver will be doing 64bit
division operations on behalf of firmware as controller's ARM CPU is very
slow in this division. Later, driver calculates Q-ARM, P-ARM and Log-ARM and
passes those values to firmware by writing these values to RAID_CONTEXT.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
RAID1 PCI bandwidth limit algorithm is not applicable to Aero as it's PCIe
Gen4 adapter.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: This issue is applicable to scenario when JBOD sequence map is
unavailable (memory allocation for JBOD sequence map failed) to driver but
feature is supported by firmware. If the driver sends a JBOD IO by not
adding 255 (MAX_PHYSICAL_DEVICES - 1) to device ID when underlying firmware
supports JBOD sequence map, it will lead to the IO failure.
Fix: For JBOD IOs, driver will not use the RAID map to fetch the devhandle
if JBOD sequence map is unavailable. Driver will set Devhandle to 0xffff
and Target ID to 'device ID + 255 (MAX_PHYSICAL_DEVICES - 1)'.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware does not expect FastPath IO sent through Region Lock Bypass queue.
Though firmware never exposes such settings when fastpath IO can be sent to
RL bypass queue but it's safer to remove dead code which directs fastpath
IO to RL Bypass queue.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: Under certain conditions, controller goes in FAULT state after IOC
INIT fired to firmware. Such Fault can be recovered through controller
reset.
Fix: In driver probe context, if firmware fault is observed post IOC INIT,
driver would do controller reset followed by retry logic for IOC INIT
command.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: There is possibility of few DCMDs timing out with 'reset_mutex' lock
held. As part of DCMD timeout handling, driver calls function
megasas_reset_fusion which also tries to acquire same lock 'reset_mutex'
and end up with deadlock.
Fix: Upon timeout of DCMDs (which are fired with 'reset_mutex' lock held),
driver will release 'reset_mutex' before calling OCR function and will
acquire lock again after OCR function returns.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On PowerPC architecture, calling disable_irq_nosync from IRQ context is not
providing the required effect.
In current megaraid_sas driver, disable_irq_nosync is being called from IRQ
context before enabling IRQ poll. But due to the issue seen on PPC, after
IRQ poll disable and legacy ISR is enabled, we are not seeing our ISR
getting called.
Fix: Call disable_irq from IRQ poll thread context instead of IRQ context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will add support for non-secure Aero adapter PCI IDs. Driver
will throw an error message when a non-secure type controller is
detected. Purpose of this interface is to avoid interacting with any
firmware which is not secured/signed by Broadcom. Any tampering on Firmware
component will be detected by hardware and it will be communicated to the
driver to avoid any further interaction with that component.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero adapters provides Atomic Request Descriptor as an alternative method
for posting an entry onto a request queue. The posting of an Atomic Request
Descriptor is an atomic operation, providing a safe mechanism for multiple
processors on the host to post requests without synchronization. This
Atomic Request Descriptor format is identical to first 32 bits of Default
Request Descriptor and uses only 32 bits.
If Aero adapters support Atomic descriptor, driver should use it for
posting IOs and DCMDs to firmware.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the logic for collecting IOP log respective to event log size.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to read event log size from MPI configuration table and
export through sysfs.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable msix load balance only when combined reply queue mode is disabled on
the SAS3 and above generation HBA devices.
Earlier msix load balance used to enable if the number of online cpus is
greater than the number of MSI-X vectors enabled on the HBA. Combined reply
queue mode will be disabled only on those HBA which works in shared
resources mode. I.e. on SAS3 HBAs it will be <= 8 and on SAS35 HBA devices
it will be <= 16.
- Before this patch if system has 256 logical CPUs and HBA exposes 128
MSI-X vectors, driver will enable msix load balance.
- After this patch if system has 256 logical CPUs and HBA exposes 128
MSI-X vectors, driver will disable msix load balance.
- After this patch if system has 256 logical CPUs and HBA exposes 16 MSI-X
vectors (due to combined reply queue mode being off in HW), driver will
enable msix load balance.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Even though 'smp_affinity_enable' module parameter is enabled, if the
number of online CPUs is bigger than the number of msix vectors enabled on
that HBA, then smp affinity settings should be disabled only for this HBA.
But currently the smp affinity setting is disabled globally and hence smp
affinity will be disabled for subsequent HBAs even though number of msix
vectors enabled for this HBA matches the number of online CPU.
To fix this, define a per HBA variable smp_affinity_enable. Initially this
variable is initialized with smp_affinity_enable module parameter value. If
this HBA has less number of msix vectors configured when compared to number
of online cpus, then only this HBA's variable smp_affinity_enable is set to
zero.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabling high iops queues, the driver should use the HBA's configured
PCIe link speed instead of looking for the maximum link speed.
I.e. enable high iops queues only if Aero/Sea HBA's configured PCIe link
speed is set to 16GT/s.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently default perf_mode is set to 'balanced' on Intel architecture
machines and on other machines default perf_mode is set to 'latency' mode.
This CPU architecture check is removed and the default perf_mode mode is
set to 'balanced' mode on all machines.
User can choose the required performance mode using perf_mode module
parameter.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ufs-tool stable release v1.0 is available at:
https://github.com/westerndigitalcorporation/ufs-tool
Feedback and bug reports, as always, are welcomed.
Signed-off-by: Arthur Simchaev <Arthur.Simchaev@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cb_arg alloc failed, we can't release the struct orig_io_req refcount
before we take its refcount. As Saurav said, move the srr_err label down
to avoid unnecessary refcount release and nullptr free.
Signed-off-by: Lin Yi <teroincn@163.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cb_arg alloc failed, we can't release the struct orig_io_req refcount
before we take its refcount. As Saurav said, move the rec_err label down
to avoid unnecessary refcount release and nullptr free.
Signed-off-by: Lin Yi <teroincn@163.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 2.12.10.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Reduce the sg_tablesize to 255.
- Reduce the MAX BDs firmware can handle to 255.
- Return IO to ML if BD goes more then 255 after split.
- Correct the size of each BD split to 0xffff.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If firmware sends either cleanup or abort completion, it means other won't
be sent. Clean out flags for other as well.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Separate out abort and cleanup flag and completion, to have better
understaning of what is getting processed.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain tests where the SCSI error handler issues an abort that is
already outstanding, we will cleanup the command so that the SCSI error
handler can proceed. In some of these cases we were seeing a command
mismatch:
kernel: scsi host2: bnx2fc: xid:0x42b eh_abort - refcnt = 2
kernel: bnx2fc: eh_abort: io_req (xid = 0x42b) already in abts processing
kernel: scsi host2: bnx2fc: xid:0x42b Entered bnx2fc_initiate_cleanup
kernel: scsi host2: bnx2fc: xid:0x42b CLEANUP io_req xid = 0x80b
kernel: scsi host2: bnx2fc: xid:0x80b cq_compl- cleanup resp rcvd
kernel: scsi host2: bnx2fc: xid:0x42b complete - rx_state = 9
kernel: scsi host2: bnx2fc: xid:0x42b Entered process_cleanup_compl refcnt = 2, cmd_type = 1
kernel: scsi host2: bnx2fc: xid:0x42b scsi_done. err_code = 0x7
kernel: scsi host2: bnx2fc: xid:0x42b sc=ffff8807f93dfb80, result=0x7, retries=0, allowed=5
kernel: ------------[ cut here ]------------
kernel: WARNING: at /root/rpmbuild/BUILD/netxtreme2-7.14.43/obj/default/bnx2fc-2.12.1/driver/bnx2fc_io.c:1347 bnx2fc_eh_abort+0x56f/0x680 [bnx2fc]()
kernel: xid=0x42b refcount=-1
kernel: Modules linked in:
kernel: nls_utf8 isofs sr_mod cdrom tcp_lp dm_round_robin xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge ebtable_filter ebtables fuse ip6table_filter ip6_tables iptable_filter bnx2fc(OE) cnic(OE) uio fcoe libfcoe 8021q libfc garp mrp scsi_transport_fc stp llc scsi_tgt vfat fat dm_service_time intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd ses enclosure ipmi_ssif i2c_core hpilo hpwdt wmi sg ipmi_devintf pcspkr ipmi_si ipmi_msghandler shpchp acpi_power_meter dm_multipath nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs sd_mod crc_t10dif
kernel: crct10dif_generic bnx2x(OE) crct10dif_pclmul crct10dif_common crc32c_intel mdio ptp pps_core libcrc32c smartpqi scsi_transport_sas fjes uas usb_storage dm_mirror dm_region_hash dm_log dm_mod
kernel: CPU: 9 PID: 2012 Comm: scsi_eh_2 Tainted: G W OE ------------ 3.10.0-514.el7.x86_64 #1
kernel: Hardware name: HPE Synergy 480 Gen10/Synergy 480 Gen10 Compute Module, BIOS I42 03/21/2018
kernel: ffff8807f25a3d98 0000000015e7fa0c ffff8807f25a3d50 ffffffff81685eac
kernel: ffff8807f25a3d88 ffffffff81085820 ffff8807f8e39000 ffff880801ff7468
kernel: ffff880801ff7610 0000000000002002 ffff8807f8e39014 ffff8807f25a3df0
kernel: Call Trace:
kernel: [<ffffffff81685eac>] dump_stack+0x19/0x1b
kernel: [<ffffffff81085820>] warn_slowpath_common+0x70/0xb0
kernel: [<ffffffff810858bc>] warn_slowpath_fmt+0x5c/0x80
kernel: [<ffffffff8168d842>] ? _raw_spin_lock_bh+0x12/0x50
kernel: [<ffffffffa0549e6f>] bnx2fc_eh_abort+0x56f/0x680 [bnx2fc]
kernel: [<ffffffff814570af>] scsi_error_handler+0x59f/0x8b0
kernel: [<ffffffff81456b10>] ? scsi_eh_get_sense+0x250/0x250
kernel: [<ffffffff810b052f>] kthread+0xcf/0xe0
kernel: [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
kernel: [<ffffffff81696418>] ret_from_fork+0x58/0x90
kernel: [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
kernel: ---[ end trace 42deb88f2032b111 ]---
The reason that there was a mismatch is that the SCSI command is actual
returned from the cleanup handler. In previous testing, the type of
cleanup notification we'd get from the CQE did not trigger the code that
returned the SCSI command. To overcome the previous behavior we would put
a reference in bnx2fc_abts_cleanup() to account for the SCSI command.
However, in cases where the SCSI command is actually off, we end up with an
extra put.
The fix for this is to only take the extra put in bnx2fc_abts_cleanup if
the completion for the cleanup times out.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For bnx2fc, the source FCoE MAC is stored in the fcoe_port struct in the
data_src_mac field. Currently this is set in fcoe_ctlr_recv_flogi which
ends up setting it by simply using fc_fcoe_set_mac() which only uses the
default FCF-MAC. We still want to store the source FCoE MAC in
port->data_src_mac but we want to snoop the FLOGI response payload so as to
set it in the following method:
1. If a granted_mac is found, use that.
2. If not granted_mac is there but there is a FCF-MAP from the FCF then
create the MAC from the FCF-MAP and the destination ID from the frame.
3. If there is no FCF-MAP the use the spec. default FCF-MAP and the
destination ID from the frame.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case of UPIU/DME request execution failed in UFS device,
ufs_bsg_request() will complete the failed bsg job by calling
bsg_job_done(). Meanwhile, it returns this error status to blk-mq layer,
then triggers blk-mq completing this request again, this will cause the
following panic.
Call trace:
ll_sc___cmpxchg_case_acq_32+0x4/0x20
complete+0x28/0x70
blk_end_sync_rq+0x24/0x30
blk_mq_end_request+0xb8/0x118
bsg_job_put+0x4c/0x58
bsg_complete+0x20/0x30
blk_done_softirq+0xb4/0xe8
do_softirq+0x154/0x3f0
run_ksoftirqd+0x4c/0x68
smpboot_thread_fn+0x22c/0x268
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
Code: f84107fe d65f03c0 d503201f f9800011 (885ffc10)
---[ end trace d92825bff6326e66 ]---
Kernel panic - not syncing: Fatal exception in interrupt
This patch is to fix this issue. The solution is to complete the ufs-bsg
job only if no error happened.
[mkp: commit description tweak]
Fixes: df032bf27a (scsi: ufs: Add a bsg endpoint that supports UPIUs)
Signed-off-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
