The biggest set of changes here is Hans' fixes and quirks for various
Baytrail based platforms with RT5640 CODECs, and there's one core fix
for a missed length assignment for __counted_by() checking. Otherwise
it's small device specific fixes, several of them in the DT bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmciNo8ACgkQJNaLcl1U
h9CNfAf/bw39l2d16DVOdzq1gv4I0BUX7M/wTsLRujnDCv8F7qZn3BhhPEeEiLDP
3wa8MzwcnXGI7rM5kzPKUERI352N7FzWUpSz6r7QtszPpttzx8HSxcHuuU68msSo
oqrUmEqA+1sFuDwsMMm85uUpeHHFQtgEhtMxMafz9VxWhTqSQCfIoM62pAns2Xdq
X3mSaovGIofWXszMjzf7tWrWfAAnzgvYjmOYNd7QwIpi/HZL9iAxw/orbLW6AZCm
ZnrhiGxf5ZZeeaiZhEzdH7iktM1+WpvLihl1PUD8JcgCHW3CJud/OqtpXV+AeyHm
p7dI0bb71g0RJ08pt+i64wxS6HA+Qg==
=I/0i
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.12-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.12
The biggest set of changes here is Hans' fixes and quirks for various
Baytrail based platforms with RT5640 CODECs, and there's one core fix
for a missed length assignment for __counted_by() checking. Otherwise
it's small device specific fixes, several of them in the DT bindings.
On a system with wcd937x, rxmacro and Qualcomm audio DSP, which is pretty
common set of devices on Qualcomm platforms, and due to the order of how
DAPM widgets are powered on (they are sorted), there is a small time window
when wcd937x chip is online and expects the flow of incoming data but
rxmacro is not yet online. When wcd937x is programmed to receive data
via AUX port then its AUX PDM watchdog is enabled in
wcd937x_codec_enable_aux_pa(). If due to some reasons the rxmacro and
soundwire machinery are delayed to start streaming data, then there is
a chance for this AUX PDM watchdog to reset the wcd937x codec. Such event
is not logged as a message and only wcd937x IRQ counter is increased
however there could be a lot of other reasons for that IRQ.
There is a similar opportunity for such delay during DAPM widgets power
down sequence.
If wcd937x codec reset happens on the start of the playback, then there
will be no sound and if such reset happens at the end of a playback then
it may generate additional clicks and pops noises.
On qrb4210 RB2 board without any debugging bits the wcd937x resets are
sometimes observed at the end of a playback though not always.
With some debugging messages or with some tracing enabled the AUX PDM
watchdog resets the wcd937x codec at the start of a playback and there
is no sound output at all.
In this patch:
- TIMEOUT_SEL bit in PDM_WD_CTL2 register is set to increase the watchdog
reset delay to 100ms which eliminates the AUX PDM watchdog IRQs on
qrb4210 RB2 board completely and decreases the number of unwanted clicks
noises;
- HOLD_OFF bit postpones triggering such watchdog IRQ till wcd937x codec
reset which usually happens at the end of a playback. This allows to
actually output some sound in case of debugging.
Cc: Adam Skladowski <a39.skl@gmail.com>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Cc: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-3-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The wcd937x supports also AUX input but the control that sets correct
soundwire port for this is missing. This control is required for audio
playback, for instance, on qrb4210 RB2 board as well as on other
SoCs.
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Reported-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Suggested-by: Adam Skladowski <a39.skl@gmail.com>
Suggested-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-2-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Infinix ZERO BOOK 13 has a 2+2 speaker system which isn't probed correctly.
This patch adds a quirk with the proper pin connections.
Also The mic in this laptop suffers too high gain resulting in mostly
fan noise being recorded,
This patch Also limit mic boost.
HW Probe for device; https://linux-hardware.org/?probe=a2e892c47b
Test: All 4 speaker works, Mic has low noise.
Signed-off-by: Piyush Raj Chouhan <piyushchouhan1598@gmail.com>
Link: https://patch.msgid.link/20241028155516.15552-1-piyuschouhan1598@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widgets array in the snd_soc_dapm_widget_list has a __counted_by
attribute attached to it, which points to the num_widgets variable. This
attribute is used in bounds checking, and if it is not set before the
array is filled, then the bounds sanitizer will issue a warning or a
kernel panic if CONFIG_UBSAN_TRAP is set.
This patch sets the size of the widgets list calculated with
list_for_each as the initial value for num_widgets as it is used for
allocating memory for the array. It is updated with the actual number of
added elements after the array is filled.
Signed-off-by: Aleksei Vetrov <vvvvvv@google.com>
Fixes: 80e698e2df ("ASoC: soc-dapm: Annotate struct snd_soc_dapm_widget_list with __counted_by")
Link: https://patch.msgid.link/20241028-soc-dapm-bounds-checker-fix-v1-1-262b0394e89e@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_gpiod_get_optional() fails, we need to disable previously enabled
regulators, as done in the other error handling path of the function.
Also, gpiod_set_value_cansleep(, 1) needs to be called to undo a
potential gpiod_set_value_cansleep(, 0).
If the "reset" gpio is not defined, this additional call is just a no-op.
This behavior is the same as the one already in the .remove() function.
Fixes: 11b9cd748e ("ASoC: cs42l51: add reset management")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/a5e5f4b9fb03f46abd2c93ed94b5c395972ce0d1.1729975570.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Some old Bay Trail tablets which shipped with Android as factory OS
have the SST/LPE audio engine described by an ACPI device with a
HID (Hardware-ID) of LPE0F28 instead of 80860F28.
Add support for this. Note this uses a new sst_res_info for just
the LPE0F28 case because it has a different layout for the IO-mem ACPI
resources then the 80860F28.
An example of a tablet which needs this is the Vexia EDU ATLA 10 tablet,
which has been distributed to schools in the Spanish Andalucía region.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241025090221.52198-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Vexia Edu Atla 10 tablet mostly uses the BYTCR tablet defaults,
but as happens on more models it is using IN1 instead of IN3 for
its internal mic and JD_SRC_JD2_IN4N instead of JD_SRC_JD1_IN4P
for jack-detection.
Add a DMI quirk for this to fix the internal-mic and jack-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024211615.79518-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On some x86 Bay Trail tablets which shipped with Android as factory OS,
the DSDT is so broken that the codec needs to be manually instantatiated
by the special x86-android-tablets.ko "fixup" driver for cases like this.
This means that the codec-dev cannot be retrieved through its ACPI fwnode,
add support to the bytcr_rt5640 machine driver for such manually
instantiated rt5640 i2c_clients.
An example of a tablet which needs this is the Vexia EDU ATLA 10 tablet,
which has been distributed to schools in the Spanish Andalucía region.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024211615.79518-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An uncomfortably large set of fixes due to me not getting round to
sending them for longer than I should due to travel and illness. This
is mostly smaller driver specific changes, but there are a couple of
generic changes:
- Bumping the minimal topology ABI we check for during validation, the
code had support for v4 removed previously but the update of the
define used for initial validation was missed.
- Fix the assumption that DAPM structs will be embedded in a component
which isn't true for card widgets when doing name comparisons, though
fortunately this is rarely triggered.
We've pulled in one Soundwire fix which was part of a larger series
fixing cleanup issues in on Intel Soundwire systems.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmcZbjoACgkQJNaLcl1U
h9BoYQf9EOlJlxr1s8iJxERcsps7BjLG1dOYeCMKEkZTG1j8BDMsKmcbXWboWQIC
0+kcfTm7DeYnXZQPJD4LllyUuWushphksllk+tTXRFqihEN9Bwa96TgzzoK+UFUc
PyfEps3fW2w1iUz4Rq4psueDl2g6X4edmqUvdSyquOiVMI0tiEbs7OQgATbdlIrG
13HlJMumQ1zblzceFnzTfCZNKHQyhNoJuzwLX5HjanEFor/OcVULtwcNA175Roqw
fpFxmmntGHFbZPqSJ2lAQmeBgYC0RH+GP6nFK2zWGN+7aLs7QM0PqEDrN16IxtpJ
h/6Hnu8scPHabrh4aYyew7YB8hXLpA==
=BQdY
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.12-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.12
An uncomfortably large set of fixes due to me not getting round to
sending them for longer than I should due to travel and illness. This
is mostly smaller driver specific changes, but there are a couple of
generic changes:
- Bumping the minimal topology ABI we check for during validation, the
code had support for v4 removed previously but the update of the
define used for initial validation was missed.
- Fix the assumption that DAPM structs will be embedded in a component
which isn't true for card widgets when doing name comparisons, though
fortunately this is rarely triggered.
We've pulled in one Soundwire fix which was part of a larger series
fixing cleanup issues in on Intel Soundwire systems.
Old procedure has a chance to meet Headphone no output.
Fixes: c2d6af53a4 ("ALSA: hda/realtek - Add default procedure for suspend and resume state")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/17b717a0a0b04a77aea4a8ec820cba13@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 15c7fab0e0 ("ASoC: qcom: Move Soundwire runtime stream alloc to
soundcards") moved the allocation of Soundwire stream runtime from the
Qualcomm Soundwire driver to each individual machine sound card driver,
except that it forgot to update SC7280 card.
Just like for other Qualcomm sound cards using Soundwire, the card
driver should allocate and release the runtime. Otherwise sound
playback will result in a NULL pointer dereference or other effect of
uninitialized memory accesses (which was confirmed on SDM845 having
similar issue).
Cc: stable@vger.kernel.org
Cc: Alexey Klimov <alexey.klimov@linaro.org>
Cc: Steev Klimaszewski <steev@kali.org>
Fixes: 15c7fab0e0 ("ASoC: qcom: Move Soundwire runtime stream alloc to soundcards")
Link: https://lore.kernel.org/r/20241010054109.16938-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241012101108.129476-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms, for example i.MX93, there is only one
audio PLL source, so some sample rate can't be supported.
If the PLL source is used for 8kHz series rates, then 11kHz
series rates can't be supported.
So add constraints according to the frequency of available
clock sources, then alsa-lib will help to convert the
unsupported rate for the driver.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1728884313-6778-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the kconfig option for the tas2781 HDA driver to select CRC32 rather
than CRC32_SARWATE. CRC32_SARWATE is an option from the kconfig
'choice' that selects the specific CRC32 implementation. Selecting a
'choice' option seems to have no effect, but even if it did work, it
would be incorrect for a random driver to override the user's choice.
CRC32 is the correct option to select for crc32() to be available.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://patch.msgid.link/20241020175624.7095-1-ebiggers@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Acer Predator G9-593 has a 2+1 speaker system which isn't probed
correctly.
This patch adds a quirk with the proper pin connections.
Note that I do not own this laptop, so I cannot guarantee that this
fixes the issue.
Testing was done by other users here:
https://discussion.fedoraproject.org/t/-/118482
This model appears to have two different dev IDs...
- 0x1177 (as seen on the forum link above)
- 0x1178 (as seen on https://linux-hardware.org/?probe=127df9999f)
I don't think the audio system was changed between model revisions, so
the patch applies for both IDs.
Signed-off-by: José Relvas <josemonsantorelvas@gmail.com>
Link: https://patch.msgid.link/20241020102756.225258-1-josemonsantorelvas@gmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The step variable is initialized to zero. It is changed in the loop,
but if it's not changed it will remain zero. Add a variable check
before the division.
The observed behavior was introduced by commit 826b5de90c
("ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size"),
and it is difficult to show that any of the interval parameters will
satisfy the snd_interval_test() condition with data from the
amdtp_rate_table[] table.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 826b5de90c ("ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size")
Signed-off-by: Andrey Shumilin <shum.sdl@nppct.ru>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://patch.msgid.link/20241018060018.1189537-1-shum.sdl@nppct.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Clean up the link DMA for playback during stop for IPC4 is required to
reset the DMA read/write pointers when the stream is prepared and
restarted after a call to snd_pcm_drain()/snd_pcm_drop().
The change is mainly on ASoC. We may go via ASoC tree with Vinod's
Acked-by tag
Ranjani Sridharan (4):
ASoC: SOF: ipc4-topology: Do not set ALH node_id for aggregated DAIs
ASoC: SOF: Intel: hda: Handle prepare without close for non-HDA DAI's
soundwire: intel_ace2x: Send PDI stream number during prepare
ASoC: SOF: Intel: hda: Always clean up link DMA during stop
drivers/soundwire/intel_ace2x.c | 19 +++++-----------
sound/soc/sof/intel/hda-dai-ops.c | 23 +++++++++----------
sound/soc/sof/intel/hda-dai.c | 37 +++++++++++++++++++++++++++----
sound/soc/sof/ipc4-topology.c | 15 +++++++++++--
4 files changed, 62 insertions(+), 32 deletions(-)
--
2.43.0
On i.MX8MM the register of volume control has positive and negative
values. It is different from other platforms like i.MX8MP and i.MX93
which only have positive values. Add a volume_sx flag to use SX_TLV
volume control for this kind of platform. Use common TLV volume control
for other platforms.
Fixes: cdfa92eb90 ("ASoC: fsl_micfil: Correct the number of steps on SX controls")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/20241017071507.2577786-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Turns out some registers of pre-2.5 version of rxmacro codecs are not
located at the expected offsets but 0xc further away in memory. So far
the detected registers are CDC_RX_RX2_RX_PATH_SEC7 and
CDC_RX_RX2_RX_PATH_DSM_CTL.
CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n) macro incorrectly generates the address
0x540 for RX2 but it should be 0x54C and it also overwrites
CDC_RX_RX2_RX_PATH_SEC7 which is located at 0x540.
The same goes for CDC_RX_RXn_RX_PATH_SEC7(rx, n).
Fix this by introducing additional rxn_reg_stride2 offset. For 2.5 version
and above this offset will be equal to 0.
With such change the corresponding RXn() macros will generate the same
values for 2.5 codec version for all RX paths and the same old values
for pre-2.5 version for RX0 and RX1. However for the latter case with
RX2 path it will also add rxn_reg_stride2 on top.
While at this, also remove specific if-check for INTERP_AUX from
rx_macro_digital_mute() and rx_macro_enable_interp_clk(). These if-check
was used to handle such special offset for AUX interpolator but since
CDC_RX_RXn_RX_PATH_SEC7(rx, n) and CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n)
macros will generate the correst addresses of dsm register, they are no
longer needed.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20241016221049.1145101-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new match table entry on Lunarlake for the TM2 laptops
with rt713 and rt1318.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241016030703.13669-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is required to reset the DMA read/write pointers when the stream is
prepared and restarted after a call to snd_pcm_drain()/snd_pcm_drop().
Also, now that the stream is reset during stop, do not save LLP registers
in the case of STOP/suspend to avoid erroneous delay reporting.
Link: https://github.com/thesofproject/sof/issues/9502
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
All: stable@vger.kernel.org # 6.10.x 6.11.x
Link: https://patch.msgid.link/20241016032910.14601-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When a PCM is restarted after a snd_pcm_drain/snd_pcm_drop(), the prepare
callback will be invoked and the hw_params will be set again. For the
HDA DAI's, the hw_params function handles this case already but not for
the non-HDA DAI's. So, add the check for link_prepared to verify if the
hw_params should be done again or not. Additionally, for SDW DAI's reset
the PCMSyCM registers as would be done in the case of a start after a
hw_free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
All: stable@vger.kernel.org # 6.10.x 6.11.x
Link: https://patch.msgid.link/20241016032910.14601-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For aggregated DAIs, the node ID is set to the group_id during the DAI
widget's ipc_prepare op. With the current logic, setting the dai_index
for node_id in the dai_config is redundant as it will be overwritten
with the group_id anyway. Removing it will also prevent any accidental
clearing/resetting of the group_id for aggregated DAIs due to the
dai_config calls could that happen before the allocated group_id is
freed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
All: stable@vger.kernel.org # 6.10.x 6.11.x
Link: https://patch.msgid.link/20241016032910.14601-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The cached version avoids redundant commands to the codec, improving
stability and reducing unnecessary operations. This change ensures
better power management and reliable restoration of pin configurations,
especially after hibernation (S4) and other power transitions.
Fixes: 9988844c45 ("ALSA: hda/conexant - Fix audio routing for HP EliteOne 1000 G2")
Suggested-by: Kai-Heng Feng <kaihengf@nvidia.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org>
Link: https://patch.msgid.link/20241016080713.46801-1-kovalev@altlinux.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DisCo for SoundWire 2.0 spec adds support for a new
sdw-manager-list property. Add it in backwards-compatible mode with
'sdw-master-count', which assumed that all links between 0..count-1
exist.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241001070611.63288-5-yung-chuan.liao@linux.intel.com
For some reason we used an array of one u8 when the specification
requires a u32.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241001070611.63288-4-yung-chuan.liao@linux.intel.com
Optimize a bit by using an intermediate 'fwnode' variable.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241001070611.63288-3-yung-chuan.liao@linux.intel.com
SDM845 sound card driver uses qcom_snd_sdw_startup() from the common
Soundwire module, so select it to fix build failures:
ERROR: modpost: "qcom_snd_sdw_startup" [sound/soc/qcom/snd-soc-sdm845.ko] undefined!
Fixes: d0e806b0cc ("ASoC: qcom: sdm845: add missing soundwire runtime stream alloc")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241012100957.129103-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Irq handler need to be executed as fast as possible, so
the log in irq handler is better to use dev_dbg which needs
to be enabled when debugging.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://patch.msgid.link/1728622433-2873-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On the HiHope boards, we have a single port with a single endpoint defined
as below:
....
rsnd_port: port {
rsnd_endpoint: endpoint {
remote-endpoint = <&dw_hdmi0_snd_in>;
dai-format = "i2s";
bitclock-master = <&rsnd_endpoint>;
frame-master = <&rsnd_endpoint>;
playback = <&ssi2>;
};
};
....
With commit 547b02f74e ("ASoC: rsnd: enable multi Component support for
Audio Graph Card/Card2"), support for multiple ports was added. This caused
probe failures on HiHope boards, as the endpoint could not be retrieved due
to incorrect device node pointers being used.
This patch fixes the issue by updating the `rsnd_dai_of_node()` and
`rsnd_dai_probe()` functions to use the correct device node pointers based
on the port names ('port' or 'ports'). It ensures that the endpoint is
properly parsed for both single and multi-port configurations, restoring
compatibility with HiHope boards.
Fixes: 547b02f74e ("ASoC: rsnd: enable multi Component support for Audio Graph Card/Card2")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/20241010141432.716868-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable slot_found is being initialized to zero and inside
a for-loop is being checked if it's reached MAX_NUM_CH, however,
this is currently impossible since slot_found is never changed.
In a previous loop a similar coding pattern is used and slot_found
is being incremented. It appears the increment of slot_found is
missing from the loop, so fix the code by adding in the increment.
Fixes: 6a8e1d46f0 ("ASoC: max98388: add amplifier driver")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20241010182032.776280-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If snd_hda_gen_add_kctl fails to allocate memory and returns NULL, then
NULL pointer dereference will occur in the next line.
Since dolphin_fixups function is a hda_fixup function which is not supposed
to return any errors, add simple check before dereference, ignore the fail.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 20e5077241 ("ALSA: hda/cs8409: Add support for dolphin")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://patch.msgid.link/20241010221649.1305-1-m.masimov@maxima.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When building for the UM arch and neither INDIRECT_IOMEM=y, nor
HAS_IOMEM=y is selected, it will fall back to the implementations from
asm-generic/io.h for IO memcpy. But these fall-back functions just do a
memcpy. So, instead of depending on UML, add dependency on 'HAS_IOMEM ||
INDIRECT_IOMEM'.
Reviewed-by: Yann Sionneau <ysionneau@kalrayinc.com>
Signed-off-by: Julian Vetter <jvetter@kalrayinc.com>
Link: https://patch.msgid.link/20241010124601.700528-1-jvetter@kalrayinc.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Line6 driver source code files contain an outdated email address of the
original author. This patch updates the contact information.
Signed-off-by: Markus Grabner <line6@grabner-graz.at>
Link: https://patch.msgid.link/20241009194251.15662-1-line6@grabner-graz.at
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit adding support for multiple control interfaces expanded struct
snd_usb_power_domain with pointer to control interface for proper control
message routing but missed one initialization point of this structure,
which has left new field with NULL value.
Standard mandates that each device has at least one control interface and
code responsible for power domain does not check for NULL values when
querying for control interface. This caused some USB devices to crash
the kernel.
Fixes: 6aa8700150 ("ALSA: usb-audio: Support multiple control interfaces")
Signed-off-by: Karol Kosik <k.kosik@outlook.com>
Link: https://patch.msgid.link/AS8P190MB1285B563C6B5394DB274813FEC782@AS8P190MB1285.EURP190.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added proper error handling for register value check that
return -EPERM when register value does not meet expected condition
Signed-off-by: Zhu Jun <zhujun2@cmss.chinamobile.com>
Link: https://patch.msgid.link/20241009073938.7472-1-zhujun2@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a problem with simultaneous audio output to headphones and
speakers, and when headphones are turned off, the speakers also turn
off and do not turn them on.
However, it was found that if you boot linux immediately after windows,
there are no such problems. When comparing alsa-info, the only difference
is the different configuration of Node 0x1d:
working conf. (windows): Pin-ctls: 0x80: HP
not working (linux): Pin-ctls: 0xc0: OUT HP
This patch disable the AC_PINCTL_OUT_EN bit of Node 0x1d and fixes the
described problem.
Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241009134248.662175-1-kovalev@altlinux.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current implementation does not work for widgets of DAPMs without
component, as snd_soc_dapm_to_component() requires it. If the widget is
directly owned by the card, e.g. as it is the case for the tegra
implementation, the call leads to UB. Therefore directly access the
component of the widget's DAPM to be able to check if a component is
available.
Fixes: f82eb06a40 ("ASoC: tegra: machine: Handle component name prefix")
Cc: stable@vger.kernel.org # v6.7+
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://patch.msgid.link/20241008-tegra-dapm-v2-1-5e999cb5f0e7@skidata.com
Signed-off-by: Mark Brown <broonie@kernel.org>
