Only tpm_tis and tpm_tis_synquacer have a dedicated way to access
multiple bytes at once, every other driver will just fall back to
read_bytes/write_bytes. Therefore, remove the read16/read32/write32
calls and move their logic to read_bytes/write_bytes.
Suggested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The Atmel TPM 1.2 chips crash with error
`tpm_try_transmit: send(): error -62` since kernel 4.14.
It is observed from the kernel log after running `tpm_sealdata -z`.
The error thrown from the command is as follows
```
$ tpm_sealdata -z
Tspi_Key_LoadKey failed: 0x00001087 - layer=tddl,
code=0087 (135), I/O error
```
The issue was reproduced with the following Atmel TPM chip:
```
$ tpm_version
T0 TPM 1.2 Version Info:
Chip Version: 1.2.66.1
Spec Level: 2
Errata Revision: 3
TPM Vendor ID: ATML
TPM Version: 01010000
Manufacturer Info: 41544d4c
```
The root cause of the issue is due to the TPM calls to msleep()
were replaced with usleep_range() [1], which reduces
the actual timeout. Via experiments, it is observed that
the original msleep(5) actually sleeps for 15ms.
Because of a known timeout issue in Atmel TPM 1.2 chip,
the shorter timeout than 15ms can cause the error described above.
A few further changes in kernel 4.16 [2] and 4.18 [3, 4] further
reduced the timeout to less than 1ms. With experiments,
the problematic timeout in the latest kernel is the one
for `wait_for_tpm_stat`.
To fix it, the patch reverts the timeout of `wait_for_tpm_stat`
to 15ms for all Atmel TPM 1.2 chips, but leave it untouched
for Ateml TPM 2.0 chip, and chips from other vendors.
As explained above, the chosen 15ms timeout is
the actual timeout before this issue introduced,
thus the old value is used here.
Particularly, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 14700us,
TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 15000us according to
the existing TPM_TIMEOUT_RANGE_US (300us).
The fixed has been tested in the system with the affected Atmel chip
with no issues observed after boot up.
References:
[1] 9f3fc7bcdd tpm: replace msleep() with usleep_range() in TPM
1.2/2.0 generic drivers
[2] cf151a9a44 tpm: reduce tpm polling delay in tpm_tis_core
[3] 59f5a6b07f tpm: reduce poll sleep time in tpm_transmit()
[4] 424eaf910c tpm: reduce polling time to usecs for even finer
granularity
Fixes: 9f3fc7bcdd ("tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers")
Link: https://patchwork.kernel.org/project/linux-integrity/patch/20200926223150.109645-1-hao.wu@rubrik.com/
Signed-off-by: Hao Wu <hao.wu@rubrik.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Do not tear down the system when getting invalid status from a TPM chip.
This can happen when panic-on-warn is used.
Instead, introduce TPM_TIS_INVALID_STATUS bitflag and use it to trigger
once the error reporting per chip. In addition, print out the value of
TPM_STS for improved forensics.
Link: https://lore.kernel.org/keyrings/YKzlTR1AzUigShtZ@kroah.com/
Fixes: 55707d531a ("tpm_tis: Add a check for invalid status")
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some TIS based TPMs can return 0xff to status reads if the locality
hasn't been properly requested. Detect this condition by checking the
bits that the TIS spec specifies must return zero are clear and return
zero in that case. Also drop a warning so the problem can be
identified in the calling path and fixed (usually a missing
try_get_ops()).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds plumbing required for drivers based on tpm_tis to set hwrng quality.
Signed-off-by: Louis Collard <louiscollard@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In the effort to remove all VLAs from the kernel[1], it is desirable to
build with -Wvla. However, this warning is overly pessimistic, in that
it is only happy with stack array sizes that are declared as constant
expressions, and not constant values. One case of this is the
evaluation of the max() macro which, due to its construction, ends up
converting constant expression arguments into a constant value result.
All attempts to rewrite this macro with __builtin_constant_p() failed
with older compilers (e.g. gcc 4.4)[2]. However, Martin Uecker,
constructed[3] a mind-shattering solution that works everywhere.
Cthulhu fhtagn!
This patch updates the min()/max() macros to evaluate to a constant
expression when called on constant expression arguments. This removes
several false-positive stack VLA warnings from an x86 allmodconfig build
when -Wvla is added:
$ diff -u before.txt after.txt | grep ^-
-drivers/input/touchscreen/cyttsp4_core.c:871:2: warning: ISO C90 forbids variable length array ‘ids’ [-Wvla]
-fs/btrfs/tree-checker.c:344:4: warning: ISO C90 forbids variable length array ‘namebuf’ [-Wvla]
-lib/vsprintf.c:747:2: warning: ISO C90 forbids variable length array ‘sym’ [-Wvla]
-net/ipv4/proc.c:403:2: warning: ISO C90 forbids variable length array ‘buff’ [-Wvla]
-net/ipv6/proc.c:198:2: warning: ISO C90 forbids variable length array ‘buff’ [-Wvla]
-net/ipv6/proc.c:218:2: warning: ISO C90 forbids variable length array ‘buff64’ [-Wvla]
This also updates two cases where different enums were being compared
and explicitly casts them to int (which matches the old side-effect of
the single-evaluation code): one in tpm/tpm_tis_core.h, and one in
drm/drm_color_mgmt.c.
[1] https://lkml.org/lkml/2018/3/7/621
[2] https://lkml.org/lkml/2018/3/10/170
[3] https://lkml.org/lkml/2018/3/20/845
Co-Developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Co-Developed-by: Martin Uecker <Martin.Uecker@med.uni-goettingen.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This flag is only used to warn if CLKRUN_EN wasn't disabled on Braswell
systems, but the only way this can happen is if the code is not correct.
So it's an unnecessary check that just makes the code harder to read.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Commit 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell
systems") disabled CLKRUN protocol during TPM transactions and re-enabled
once the transaction is completed. But there were still some corner cases
observed where, reading of TPM header failed for savestate command
while going to suspend, which resulted in suspend failure.
To fix this issue keep the CLKRUN protocol disabled for the entire
duration of a single TPM command and not disabling and re-enabling
again for every TPM transaction. For the other TPM accesses outside
TPM command flow, add a higher level of disabling and re-enabling
the CLKRUN protocol, instead of doing for every TPM transaction.
Fixes: 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Making cmd_getticks 'const' introduced a couple of harmless warnings:
drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)
This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.
Cc: stable@vger.kernel.org
Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Since commit 1107d065fd ("tpm_tis: Introduce intermediate layer for
TPM access") Atmel 3203 TPM on ThinkPad X61S (TPM firmware version 13.9)
no longer works. The initialization proceeds fine until we get and
start using chip-reported timeouts - and the chip reports C and D
timeouts of zero.
It turns out that until commit 8e54caf407 ("tpm: Provide a generic
means to override the chip returned timeouts") we had actually let
default timeout values remain in this case, so let's bring back this
behavior to make chips like Atmel 3203 work again.
Use a common code that was introduced by that commit so a warning is
printed in this case and /sys/class/tpm/tpm*/timeouts correctly says the
timeouts aren't chip-original.
Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
To avoid code duplication between the old tpm_tis and the new and future
native tcg tis driver(ie: spi, i2c...), the tpm_tis driver was reworked,
so that all common logic is extracted and can be reused from all drivers.
The core methods can also be used from other TIS like drivers.
itpm workaround is now managed with a specific tis flag
TPM_TIS_ITPM_POSSIBLE.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This splits tpm_tis in a high-level protocol part and a low-level interface
for the actual TPM communication. The low-level interface can then be
implemented by additional drivers to provide access to TPMs using other
mechanisms, for example native I2C or SPI transfers, while still reusing
the same TIS protocol implementation.
Though the ioread/iowrite calls cannot fail, other implementations of this
interface might want to return error codes if their communication fails.
This follows the usual pattern of negative values representing errors and
zero representing success. Positive values are not used (yet).
Errors are passed back to the caller if possible. If the interface of a
function does not allow that, it tries to do the most sensible thing it
can, but this might also mean ignoring the error in this instance.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Split priv_data structure in common and phy specific structures. This will
allow in future patches to reuse the same tis logic on top of new phy such
as spi and i2c. Ultimately, other drivers may reuse this tis logic.
(e.g: st33zp24...)
iobase field is specific to TPM addressed on 0xFED4xxxx on LPC/SPI bus.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
