Pull thermal fixes from Eduardo Valentin:
"Minor fixes to OF thermal, qoriq, and rcar drivers"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: of-thermal: disable passive polling when thermal zone is disabled
thermal: rcar_gen3_thermal: convert to SPDX identifiers
thermal: rcar_thermal: convert to SPDX identifiers
thermal: qoriq: Switch to SPDX identifier
thermal: qoriq: Simplify the 'site' variable assignment
thermal: qoriq: Use devm_thermal_zone_of_sensor_register()
Pull thermal management updates from Zhang Rui:
- Add Daniel Lezcano as the reviewer of thermal framework and SoC
driver changes (Daniel Lezcano).
- Fix a bug in intel_dts_soc_thermal driver, which does not translate
IO-APIC GSI (Global System Interrupt) into Linux irq number (Hans de
Goede).
- For device tree bindings, allow cooling devices sharing same trip
point with same contribution value to share cooling map (Viresh
Kumar).
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
dt-bindings: thermal: Allow multiple devices to share cooling map
MAINTAINERS: Add Daniel Lezcano as designated reviewer for thermal
Thermal: Intel SoC DTS: Translate IO-APIC GSI number to linux irq number
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When thermal zone is in passive mode, disabling its mode from
sysfs is NOT taking effect at all, it is still polling the
temperature of the disabled thermal zone and handling all thermal
trips, it makes user confused. The disabling operation should
disable the thermal zone behavior completely, for both active and
passive mode, this patch clears the passive_delay when thermal
zone is disabled and restores it when it is enabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no need to assign zero to the variable 'site' and then
perform a compound bitwise OR operation afterwards.
Make it simpler by assigning the final 'site' value directly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
By using the managed devm_thermal_zone_of_sensor_register() we can
drop the explicit call to thermal_zone_of_sensor_unregister() in the
qoriq_tmu_remove() function, which simplifies the code a bit.
So switch to devm_thermal_zone_of_sensor_register().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Eduardo Valentin:
- rework tsens driver to add support for tsens-v2 (Amit Kucheria)
- rework armada thermal driver to use syscon and multichannel support
(Miquel Raynal)
- fixes to TI SoC, IMX, Exynos, RCar, and hwmon drivers
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (34 commits)
thermal: armada: fix copy-paste error in armada_thermal_probe()
thermal: rcar_thermal: avoid NULL dereference in absence of IRQ resources
thermal: samsung: Remove Exynos5440 clock handling left-overs
thermal: tsens: Fix negative temperature reporting
thermal: tsens: switch from of_iomap() to devm_ioremap_resource()
thermal: tsens: Rename variable
thermal: tsens: Add generic support for TSENS v2 IP
thermal: tsens: Rename tsens-8996 to tsens-v2 for reuse
thermal: tsens: Add support to split up register address space into two
dt: thermal: tsens: Document the fallback DT property for v2 of TSENS IP
thermal: tsens: Get rid of unused fields in structure
thermal_hwmon: Pass the originating device down to hwmon_device_register_with_info
thermal_hwmon: Sanitize attribute name passed to hwmon
dt-bindings: thermal: armada: add reference to new bindings
dt-bindings: cp110: add the thermal node in the syscon file
dt-bindings: cp110: update documentation since DT de-duplication
dt-bindings: ap806: add the thermal node in the syscon file
dt-bindings: cp110: prepare the syscon file to list other syscons nodes
dt-bindings: ap806: prepare the syscon file to list other syscons nodes
dt-bindings: cp110: rename cp110 syscon file
...
The return value from devm_kzalloc() is not checked correctly. The
test is done against a wrong variable. Fix it.
Fixes: e72f03ef2543 ("thermal: armada: use the resource managed registration helper alternative")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Ensure that the base address used by a call to rcar_thermal_common_write()
may be NULL if the SOC supports interrupts for use with the thermal device
but none are defined in DT as is the case for R-Car H1 (r8a7779). Guard
against this condition to prevent a NULL dereference when the device is
probed.
Tested on:
* R-Mobile APE6 (r8a73a4) / APE6EVM
* R-Car H1 (r8a7779) / Marzen
* R-Car H2 (r8a7790) / Lager
* R-Car M2-W (r8a7791) / Koelsch
* R-Car M2-N (r8a7793) / Gose
* R-Car D3 ES1.0 (r8a77995) / Draak
Fixes: 1969d9dc20 ("thermal: rcar_thermal: add r8a77995 support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Commit 8014220d48 ("thermal: samsung: Remove support for Exynos5440")
removed the Exynos5440 specific part of code for accessing TMU interrupt
registers but the surrounding clock handling was left.
Clean it up.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The current code will always return 0xffffffff in case of negative
temperatures due to a bug in how the binary sign extension is being done.
Use sign_extend32() instead.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
devm_ioremap_resources() automatically requests resources (so that the I/O
region shows up in /proc/iomem) and devm_ wrappers do better error handling
and unmapping of the I/O region when needed.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We're actually reading the temperature from the status register. Fix the
variable name to reflect that.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
SDM845 uses v2 of the TSENS IP block but the get_temp() function appears to
be identical across v2.x.y in code seen so far. We use the generic
get_temp() function defined as part of ops_generic_v2.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The TSENS block inside the 8996 is internally classified as version 2 of
the IP. Several other SoC families use this block and can share this code.
We rename get_temp() to reflect that it can be used across the v2 family.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There are two banks of registers for v2 TSENS IPs: SROT and TM. On older
SoCs these were contiguous, leading to DTs mapping them as one register
address space of size 0x2000. In newer SoCs, these two banks are not
contiguous anymore.
Add logic to init_common() to differentiate between old and new DTs and
adjust associated offsets for the TM register bank so that the old DTs will
continue to function correctly.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
status_field and trdy are unused in any of the tsens drivers. Remove them.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When registering the hwmon device, we pass NULL as the device.
While this doesn't result in any immediate breakage, it leaves
the hwmon device at the root of the virtual devices, rather than
attached to the thermal zone hierarchy.
Instead, let's pass the actual device, which is part of the
thermal_zone_device structure. This also avoids the rather
unpleasant ""NULL device *" which can be generated by dev_{err,info}
in the hwmon subsystem.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
My Chromebook Plus (kevin) is spitting the following at boot time:
(NULL device *): hwmon: 'sbs-9-000b' is not a valid name attribute, please fix
Clearly, __hwmon_device_register is unhappy about the property name.
Some investigation reveals that thermal_add_hwmon_sysfs doesn't
sanitize the name of the attribute.
In order to keep it quiet, let's replace '-' with '_' in hwmon->type
This is consistent with what iio-hwmon does since b92fe9e337.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The implementation of armada_is_valid() is very simple and is the same
across all the versions of the IP since the ->is_valid_bit has been
introduced. Simplify the structure by getting rid of the function
pointer and calling directly the function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Sensor selection when using multiple sensors already checks for the
sensor validity. Move it to the legacy ->get_temp() hook, where it is
still needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When using new bindings with multiple sensors, sensor validity is
checked twice because sensor selection also checks for the validity.
Remove the redundant call from the IP initialization helper and move it
to the legacy probe section where it is still needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
MVEBU thermal IP supports multiple channels. Each channel may have
several sensors but for now each channel is wired to only one thermal
sensor. The first channel always points to the so called internal
sensor, within the thermal IP. There is usually one more channel (with
one sensor each time) per CPU. The code has been written to support
possible evolutions of the ap806 IP that would embed more CPUs and thus
more channels to select. Each channel should be referenced in the device
tree as an independent thermal zone.
Add the possibility to read each of these sensors through sysfs by
registering all the sensors (translated in "thermal_zone"). Also add a
mutex on these accesses to avoid read conflicts (only one channel/sensor
may be selected and read at a time).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Current use of thermal_zone_device_register() triggers a warning at boot
and should be replaced by devm_thermal_zone_of_sensor_register(). This
allows better handling of multiple thermal zones for later multi-sensors
support.
Also change the driver data to embed a new structure to make the
difference between legacy data (which needs to be cleaned) and
syscon-related data.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Until recently, only one register was referenced in MVEBU thermal IP
node. Recent changes added a second entry pointing to another
register right next to it. We cannot know for sure that we will not
have to access other registers. That will be actually the case when
overheat interrupt feature will come, where it will be needed to access
DFX registers in the same area.
This approach is not scalable so instead of adding consinuously memory
areas in the DT (and change the DT bindings, while keeping backward
compatibility), move the thermal node into a wider syscon from which it
will be possible to also configure the thermal interrupt.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Configure the sample frequency and number of averaged samples.
This is needed for two reasons:
1/ To be bootloader independent.
2/ To prepare the introduction of multi-sensors support by preventing
inconsistencies when reading temperatures that could be a mean of
samples took from different sensors.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Until now, Armada 380 and CP110 could share the same ->init() function
because their use was identical.
Prepare the support of multi-sensors support and overheat interrupt
feature by separating the initialization paths before they actually
diverge.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Calling a hook ->init_sensor() while what is initialized is the IP
itself and not the sensors is misleading. Rename the hook ->init() to
avoid any confusion in later work bringing multi-sensors support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On older versions of this thermal IP, TSEN referred as the internal
sensor in the thermal IP while EXT_TSEN referred as sensors outside of
this IP, ie in the CPUs most of the time. The bit names in the
specifications do not follow this rule anymore, so remove these comments
that are misleading.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Prepare the migration to use regmaps by first simplifying the
initialization functions: avoid unnecessary write/read cycles on
configuration registers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal zone names must follow certain rules imposed by the framework.
They are limited in length and shall not have any hyphen '-'.
This is done in a separate function for future use in another location.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Majority of this code (i.e. functions from ti-bandgap.c) has been
introduced in May 2013 by commit eb982001db ("thermal: introduce TI
SoC thermal driver"). Just remove it altogether (in case it is needed
it can be easily resurrected from git repo).
While at it fix incorrect "not used" comments.
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Intel SoC DTS uses a hardcoded GSI number, before this commit
it was passing it to request_irq as if it were a linux irq number,
but there is no 1:1 mapping so in essence it was requesting a
random interrupt.
Besides this causing the DTS driver to not actually get an interrupt
if the thermal thresholds are exceeded this also is causing an
interrupt conflict on some devices since the linux irq 86 which is
being requested is already in use, leading to oopses like this:
genirq: Flags mismatch irq 86. 00002001 (soc_dts) vs. 00000083 (volume_down)
CPU: 0 PID: 601 Comm: systemd-udevd Tainted: G C OE 4.17.0-rc6+ #45
Hardware name: Insyde i86/Type2 - Board Product Name, BIOS CHUWI.D86JLBNR03 01/14/2015
Call Trace:
dump_stack+0x5c/0x80
__setup_irq.cold.50+0x4e/0xac
? request_threaded_irq+0xad/0x160
request_threaded_irq+0xf5/0x160
? 0xffffffffc0a93000
intel_soc_thermal_init+0x74/0x1000 [intel_soc_dts_thermal]
This commit makes the intel_soc_dts_thermal.c code call
acpi_register_gsi() to translate the hardcoded IO-APIC GSI number (86)
to a linux irq, so that the dts code uses the right interrupt and we
no longer get an oops about an irq conflict.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Without this fix, the thermal probe on i.MX6 might trigger a division
by zero exception later in the probe if the calibration does fail.
Note: This linux behavior (Division by zero in kernel) has been triggered
on a Qemu i.MX6 emulation where parameters in nvmem were not set. With this
fix the division by zero is not triggeed anymore as the thermal probe does
fail early.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cooling device should be part of the i.MX cpufreq driver, but it
cannot be removed for the sake of DT stability. So turn the cooling
device registration into a separate function and perform the
registration only if the CPU OF node does not have the #cooling-cells
property.
Use of_cpufreq_power_cooling_register in imx_thermal code to link the
cooling device to the device tree node provided.
This makes it possible to bind the cpufreq cooling device to a custom
thermal zone via a cooling-maps entry like:
cooling-maps {
map0 {
trip = <&board_alert>;
cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
Assuming a cpu node exists with label "cpu0" and #cooling-cells
property.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
Pull thermal SoC updates from Zhang Rui:
"Thermal SoC management updates:
- imx thermal driver now supports i.MX7 thermal sensor (Anson Huang)
- exynos thermal driver dropped support for exynos 5440 (Krzysztof
Kozlowski)
- rcar_thermal now supports r8a77995 (Yoshihiro Kaneko)
- rcar_gen3_thermal now supports r8a77965 (Niklas Söderlund)
- qcom-spmi-temp-alarm now supports GEN2 PMIC peripherals (David
Collins)
- uniphier thermal now supports UniPhier PXs3 (Kunihiko Hayashi)
- mediatek thermal now supports MT7622 SoC (Sean Wang)
- considerable refactoring of exynos driver (Bartlomiej
Zolnierkiewicz)
- small fixes all over the place on different drivers"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (50 commits)
thermal: qcom: tsens: Allow number of sensors to come from DT
thermal: tegra: soctherm: add const to struct thermal_cooling_device_ops
thermal: exynos: Reduce severity of too early temperature read
thermal: imx: Switch to SPDX identifier
thermal: qcom-spmi-temp-alarm: add support for GEN2 PMIC peripherals
thermal: ti-soc-thermal: fix incorrect entry in omap5430_adc_to_temp[]
thermal: rcar_thermal: add r8a77995 support
dt-bindings: thermal: rcar-thermal: add R8A77995 support
thermal: mediatek: use of_device_get_match_data()
thermal: exynos: remove trip reporting to user-space
thermal: exynos: remove unused defines for Exynos5433
thermal: exynos: cleanup code for enabling threshold interrupts
thermal: exynos: check return values of ->get_trip_[temp, hyst] methods
thermal: exynos: move trips setting to exynos_tmu_initialize()
thermal: exynos: set trips in ascending order in exynos7_tmu_initialize()
thermal: exynos: do not use trips structure directly in ->tmu_initialize
thermal: exynos: add exynos*_tmu_set_[trip,hyst]() helpers
thermal: exynos: move IRQs clearing to exynos_tmu_initialize()
thermal: exynos: clear IRQs later in exynos4412_tmu_initialize()
thermal: exynos: make ->tmu_initialize method void
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIbBAABAgAGBQJbFnd0AAoJEFKgDEdIgJTyuWgP+O/+kRbXR5WTphJ8e9+CqHp4
LF6AJXTuiA0fPJ5TcTNtZ84AVvmoNcTXnaM3Ou8HfR2qER8Gqu4WbdcfqhU2/KUq
L4x4YlW+DZPOhy7chFx/yTgdSWc8vBwSG80DLSQhjnOJBY4SwBaVSSCYi/CSiAvr
I18zt03mSXUe9RADrT3W0rbryIbyICvZjMbKkUlSm7ZTQv482FaU2Jezp86qDYLB
FWc7QOLKzXRjFTg5IQ91mTtqnM2gnHwqOzGFR+jILn8BQwVe5dYp42sCSne34kBD
pHz5GosIIYRH3Eik7pNzOhN4nsncLfPwwQQx/YH1KmKteNPTPJZO01pEwMaurc3w
LaoTD7LNDyZCkzxJF/kKOiW4ys1cMf5jyoiV9Sou7PIVPcxuR1ToMXQvHSplZPG1
UyDwW41XVmluYdC2O4ybRQWMu3nmrQKCjjGkCmizK3xMWNs4u/5Y4kS3mi7Zwk3y
X1wlm2BW7RPzVl7WWlNergR2UHNq2zgToOWzFfSqXtMukYbmei+mXYIIe6nKa2GH
ji/d/Sr/RIAgUs46sBzRBLK9ZCqybPxSvnfNZx8WodLU1dLYT3yY1vGZbGPEMB2w
puS7ctPT9dfnBxi/MOegXlTyKTOJkCB3o/bsWkIdSvRI45qbYE1aQN8IMmDQ20sv
X8A3LnDQZvUfKEULrU0=
=hB2y
-----END PGP SIGNATURE-----
Merge tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Help userspace log daemons to catch up with a flood of messages. They
will get woken after each message even if the console is far behind
and handled by another process.
- Flush printk safe buffers safely even when panic() happens in the
normal context.
- Fix possible va_list reuse when race happened in printk_safe().
- Remove %pCr printf format to prevent sleeping in the atomic context.
- Misc vsprintf code cleanup.
* tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
printk: drop in_nmi check from printk_safe_flush_on_panic()
lib/vsprintf: Remove atomic-unsafe support for %pCr
serial: sh-sci: Stop using printk format %pCr
thermal: bcm2835: Stop using printk format %pCr
clk: renesas: cpg-mssr: Stop using printk format %pCr
printk: fix possible reuse of va_list variable
printk: wake up klogd in vprintk_emit
vsprintf: Tweak pF/pf comment
lib/vsprintf: Mark expected switch fall-through
lib/vsprintf: Replace space with '_' before crng is ready
lib/vsprintf: Deduplicate pointer_string()
lib/vsprintf: Move pointer_string() upper
lib/vsprintf: Make flag_spec global
lib/vsprintf: Make strspec global
lib/vsprintf: Make dec_spec global
lib/test_printf: Mark big constant with UL
Printk format "%pCr" will be removed soon, as clk_get_rate() must not be
called in atomic context.
Replace it by printing the variable that already holds the clock rate.
Note that calling clk_get_rate() is safe here, as the code runs in task
context.
Link: http://lkml.kernel.org/r/1527845302-12159-3-git-send-email-geert+renesas@glider.be
To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
For platforms that has multiple copies of the TSENS hardware block it's
necessary to be able to specify the number of sensors per block in DeviceTree.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Correct the typecast with const to struct thermal_cooling_device_ops.
It is the last argument to the function thermal_of_cooling_device_register
and this argument is of type const. So, declare this structure
thermal_cooling_device_ops as constant.
Signed-off-by: sumeet p <srplinux2008@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal core tries to read temperature during sensor registering in
thermal_zone_of_sensor_register(). In that time Exynos TMU driver and
hardware are not yet initialized. Commit 0eb875d88a ("thermal:
exynos: Reading temperature makes sense only when TMU is turned on")
added a boolean flag to prevent reading bogus temperature in such
case but it exposed warning message during boot:
[ 3.864913] thermal thermal_zone0: failed to read out thermal zone (-22)
Return EAGAIN in such case to skip omitting such message because it
might mislead user.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
